all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 1.45 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Attestation Statements | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Cover Letter(s) | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual | Users Manual | 1.45 MiB |
UMxxxx USER MANUAL Evaluation Board STEVAL-WESU1 Introduction The STEVAL-WESU1 is a System Evaluation Board designed to provide a cost effective solution for precise motion sensing in wearable applications. The system is featuring a low power ARM Cortex-M3 microcontroller unit (STM32L151), an iNEMO inertial module (LSM6DS3), a high performance magnetometer (LIS3MDL), a barometric pressure sensor (LPS25HB), a Bluetooth low energy wireless network processor (BLUENRG-MS) and power management circuitry that allows fast charging and precise energy estimation (STNS01 and STC3115). The connectivity granted by the best in class BLUENRG-MS and supported by the integrated balun (BALF-NRG-
01D3) permit to maximize the RF performances with low area occupancy and design effort and pass the RF Test for FCC certification (FCC ID: S9NWESU1) and IC certification (IC ID: 8976C-
WESU1). An Android and iOS APP, available on Google Play and Apple Store, can be used for displaying information sent by the STEVAL-WESU1 through BLE connectivity as well as for setting operative modes. Figure 1. STEVAL-WESU1 evaluation board Rev 0.1 STMicroelectronics Confidential 1/22 July 2015 1 2 3 4 5 6 Table of Contents Board Description and Getting started ................................................................................... 4 Getting started ........................................................................................................................ 5 1.1 Hardware description ............................................................................................................... 8 Microcontroller ........................................................................................................................ 8 Sensors .................................................................................................................................. 8 LSM6DS3 ............................................................................................................................... 8 LISM3DL ................................................................................................................................ 8 LPS25HB ................................................................................................................................ 9 BLUENRG-MS and BALF-NRG-01D3 ................................................................................... 9 Power management ............................................................................................................... 9 STNS01 and STLQ015 .......................................................................................................... 9 STC3115 .............................................................................................................................. 10 Connectors ........................................................................................................................... 10 Battery connector ................................................................................................................. 10 SWD Connector and external peripherals............................................................................ 11 USB Connector .................................................................................................................... 12 Exposed pad connector ....................................................................................................... 12 uFL connector ...................................................................................................................... 12 Buttons and LEDs ................................................................................................................ 12 2.1 2.2 2.2.1 2.2.2 2.2.3 2.3 2.4 2.4.1 2.4.2 2.5 2.5.1 2.5.2 2.5.3 2.5.4 2.5.5 2.6 Formal notices required by the U.S. Federal Communications Commission ("FCC") ....... 13 Formal notices required by the Industry Canada ("IC") ....................................................... 14 Board schematic and bill of material ..................................................................................... 15 Bill of material ....................................................................................................................... 15 Schematic ............................................................................................................................. 19 5.1 5.2 Revision history ...................................................................................................................... 20 2/22 Version 0.1 STMicroelectronics Confidential Error! No text of specified style in document. ST application note template 1 Board Description and Getting started The STEVAL-WESU1 is a System Evaluation Board designed and optimized in order to be a reference design for users would made their own wearable electronic devices. In fact, the system architecture is made up of hardware, firmware and software solutions to accelerate the overall development of all applications: from embedded end-customer devices to mobile software development. The design choices have been taken to address accurate motion tracking suitable for training in every kind of activity or sport. Main Components:
- STM32L151VEY6, ultra-low-power ARM Cortex-M3 MCU with 512 Kbytes FLASH, 48kBytes of RAM in WLCSP100 package
- BLUENRG-MS, Bluetooth Low Energy (BLE) single-mode network processor, compliant with Bluetooth specification core 4.0
- BALF-NRG-01D3, 50 balun for BLUENRG-MS transceiver with integrated harmonic filter
- LSM6DS3, inertial module 3D accelerometer
(2/4/8g) + 3D gyroscope iNEMO
(245/500/2000dps)
- LIS3MDL, MEMS 3D magnetometer (4/8/12/16 gauss)
- LPS25HB, MEMS pressure sensor, 260-1260 hPa absolute digital output barometer
- STC3115, Gas gauge IC with alarm output
- STNS01, Li-Ion linear battery charger
- STLQ015XG30R, linear voltage regulator The Figure 2 shows a function block diagram of the board where the sensors and the BLUENRG-
MS are connected to microcontroller through two separate SPI peripherals, meanwhile the power management is driven by I2C peripheral. The system can be powered with USB connected to PC or through specific battery. The USB is also used for battery recharge. Figure 3 shows the block diagram of the RFIC BLUENRG-MS. Figure 2. Functional Block Diagram DRAFT STMicroelectronics Confidential Rev 0.1 4/22 ST application note template Error! No text of specified style in document. Figure 3. Block Diagram of RFIC: BlueNRG-MS DRAFT 1.1 Getting started The system is delivered fully assembled and connected with battery and with LDO off (shipment mode, with 2uA power consumption). It can be simply switched ON with USB-powered cable insertion (micro B male plug). The USB port connector can be used for battery charging. The system takes up to 160mA (@5V) to recharge the battery; for this reason you can use both USB wall adapter and PC port with this capability. Two LEDs (LED1 and LED2, see Figure 3) describes the Application Status and the Battery Charging Status. The Charging LED (LED 2) could be:
- Light ON, the USB plug is correctly connected and the board is charging;
- Light OFF, the board is not charging (use USB cable reconnection to force re-start);
- Blinking (approximately at 1Hz), charging failure (e.g. over-temperature, three wires battery not connected);
It is important to avoid deep discharge (< 30%) to maintain battery integrity and to prevent long-
term malfunctioning. The User Button (see Figure 4) can be pressed to enter and exit the Stop MODE. At power on the Application LED (LED1) starts with one smooth blink and in normal operation it blinks at 2s interval; after BLUENRG-MS connection the blinking interval becomes 1s and STEVAL-WESU1 system reads sensors data and sends it to a Bluetooth Smart Ready device; the data is displayed using a dedicated App. STMicroelectronics Confidential Rev 0.1 5/22 Error! No text of specified style in document. ST application note template A custom (1.27 mm pitch) SWD connector is used to have a compact solution, since to program the on-board STM32L151 it has been included in the package a specific adapter useful to be connected to a programmer tool (e.g. ST-LINK/v2). Figure 4. Board Layout top layer DRAFT Figure 5. Board Layout Bottom layer 6/22 Version 0.1 STMicroelectronics Confidential ST application note template Error! No text of specified style in document. Once it has been verified the battery is enough charged, the board is ready to be used. To visualize the information sent through the Bluetooth Low Energy connectivity is fundamental to install one of the App available for the Smartphone and Tablet:
- ST WESU Android App, available on Google Play;
- ST WESU iOS App available on Apple Store. To use this App is need a Smartphone or Tablet supporting the BLE connectivity, i.e. iPhone 4S and subsequent or, an Android based device with Android OS 4.3 or higher. DRAFT STMicroelectronics Confidential Rev 0.1 7/22 Error! No text of specified style in document. ST application note template 2 Hardware description This section describes the main components present on the board and described in Figure 3 and 4. 2.1 Microcontroller STM32L151VEY6 is an ultra-low-power microcontroller unit based on ARM Cortex M3. It features a great range of low power modes and an efficient voltage scaling that allows power saving. 2.2 Sensors 2.2.1 LSM6DS3 Thanks to their overall integration level the embedded sensors offer great flexibility in terms of accuracy of the system and in terms of power consumption. The integrated sensors perfectly fit the needs of an accurate AHRS algorithm (e.g. embedded iNEMO-Engine running on the STM32L151VEY6), height estimation and everything needed for wearable motion tracking: from extreme low power activity tracker to more advanced motion reconstruction. DRAFT The LSM6DS3 is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope performing at 1.25 mA (up to 1.6 kHz ODR) in high performance mode and enabling always-on low-power features for an optimal motion experience for the consumer. Up to 8 Kbyte of FIFO with dynamic allocation of significant data (i.e. external sensors, time stamp, etc) allows the overall power saving of the system.. STs family of MEMS sensor modules leverages the robust and mature manufacturing processes already used for the production of micro machined accelerometers and gyroscopes. The various sensing elements are manufactured using specialized micromachining processes, while the IC interfaces are developed using CMOS technology that allows the design of a dedicated circuit which is trimmed to better match the characteristics of the sensing element. The LSM6DS3 has a full-scale acceleration range of 2/4/8/16 g and an angular rate range of 125/245/500/1000/2000 dps. High robustness to mechanical shock makes the LSM6DS3 the preferred choice of system designers for the creation and manufacturing of reliable products. The LSM6DS3 is available in a plastic land grid array (LGA) package. 2.2.2 LISM3DL The LIS3MDL is an ultra-low-power high performance three-axis magnetic sensor. The LIS3MDL has user-selectable full scales of 4/ 8/ 12/16 gauss. The self-test capability allows the user to check the functioning of the sensor in the final application. The device may be configured to generate interrupt signals for magnetic field detection. The LIS3MDL includes an I2C serial bus interface that supports standard and fast mode (100 kHz and 400 kHz) and SPI serial standard interface. The LIS3MDL is available in a small thin plastic land grid array package (LGA) and is guaranteed to operate over an extended temperature range of -40 C to +85 C. 8/22 Version 0.1 STMicroelectronics Confidential ST application note template Error! No text of specified style in document. 2.2.3 LPS25HB The LPS25HB is an ultra-compact absolute piezo-resistive pressure sensor. It includes a monolithic sensing element and an IC interface able to take the information from the sensing element and to provide a digital signal to the external world. Thanks to its great accuracy (1 Pa RMS, 24bit ADC resolution), its bandwidth (1 Hz 25 Hz) and to its very low power consumption (4uA low power mode, 25uA high performance mode) the integration of this sensor is suitable for height estimation (e.g. VRU Vertical Reference Unit) and to enhance standard IMU performances with high frequency altitude reference. 2.3 BLUENRG-MS and BALF-NRG-01D3 The BLUENRG-MS is a very low power Bluetooth low energy (BLE) single-mode network processor, compliant with Bluetooth specification v4.1. The BLUENRG-MS can act as master or slave. The entire Bluetooth low energy stack runs on the embedded Cortex M0 core. The non-volatile Flash memory allows on-field stack upgrading. The BLUENRG-MS allows applications to meet the tight advisable peak current requirements imposed with the use of standard coin cell batteries. The maximum peak current is only 8.2 mA at 0 dBm of output power. Ultra low-power sleep modes and very short transition times between operating modes allow very low average current consumption, resulting in longer battery life. The BLUENRG-MS offers the option of interfacing with external microcontrollers using SPI transport layer. BALF-NRG-01D3 is a 50 conjugate match to BLUENRG-MS (QFN32 package) that integrates balun transformer and harmonics filtering. It features high RF performances with a very small footprint and a RF BOM reduction. It has been chosen as the best trade-off for costs, area occupation and high radio performances. The layout has been optimized to match 4 layers design and a chip antenna. DRAFT 2.4 Power management The power management block includes the STNS01, the STLQ015 and the STC3115 2.4.1 STNS01 and STLQ015 The STNS01 is a linear charger for single-cell Li-Ion batteries. In STEVAL-WESU1 system it is configured as battery charger and as power path selected between USB power source and battery power source. The STNS01's battery charger is designed to charge single cell Li-Ion batteries up to 4.2 V using a CC-CV charging algorithm (see STNS01 datasheet for more details). When a valid input voltage is detected, the STNS01 starts the charge cycle and the CHG pin switches from high impedance to low level. The CHG pin is connected to LED2 to monitor the charger. The charging status LED (LED 2) can be:
-
-
- blinking (approx. 1Hz): charging failure (e.g. over-temperature, three wires battery not solid ON: the USB plug is correctly connected and the board is charging;
solid OFF: the board is not charging (use USB cable reconnection to force re-start);
connected);
STMicroelectronics Confidential Rev 0.1 9/22 Error! No text of specified style in document. ST application note template The SYS pin is the voltage output of STNS01 selected power path. That SYS pin is connected to the linear voltage regulator STLQ015XG30R that provide a 3V (VDD) to all other devices. The STM32L151 is also connected to its SHDN pin to disconnect the power delivery to most of the devices and enable the shipment mode. 2.4.2 STC3115 The STC3115 includes the hardware functions required to implement a low-cost gas gauge for battery monitoring. The STC3115 uses current sensing, Coulomb counting and accurate measurements of the battery voltage to estimate the state-of-charge (SOC) of the battery. An internal temperature sensor simplifies implementation of temperature compensation. An alarm output signals a low SOC condition and can also indicate low battery voltage. The alarm threshold levels are programmable. The STC3115 offers advanced features to ensure high performance gas gauging in all application conditions. 2.5 Connectors The following sub-sections describe the connectors of STEVAL-WESU1 board (see Figure 4 as reference). The STEVAL-WESU1 has L form factor (see Figure 4), suitable to host the battery (i.e. 12xd25mm @ 85 mAh) in plane with the PCB and optimize the final design. DRAFT Figure 5 Photo of STEVAL-WESU1 with Battery 2.5.1 Battery connector Battery connector is placed on the shrink side of the board (see Figure 2). Its hardware connection is shown in Figure 6 Figure 6 Battery connector Schematic 10/22 Version 0.1 STMicroelectronics Confidential ST application note template Error! No text of specified style in document. 2.5.2 SWD Connector and external peripherals A custom 10 pin (1.27 mm pitch) connector is soldered. It can be used:
-
to program on-board microcontroller through a dedicated adapter connected to programmer tool (like ST-Link) (Figure 7)
- as an expansion connector to allow user to access to other board features as described in Table1 Figure 7: SWD Connector DRAFT Table1 Expansion Connector GPIO Description Expansion Connector GPIO Description Exp. Pin J500 Port/Pin Default func. Expansion PIN PWM USART ADC 8 3 6 A2 B0 A3 TP512 B12 Push Button User LED
-
-
1 2 3 4 TIM2CH3 USART2_TX ADC_CH2 TIM3CH3 ADC_CH8 TIM2CH4 USART2_RX ADC_CH3 TIM10CH1 ADC_CH18 STMicroelectronics Confidential Rev 0.1 11/22 Error! No text of specified style in document. ST application note template 2.5.3 USB Connector The USB connector accepts a micro USB type B and it is used to charge the battery or to power the board if battery is not present. 2.5.4 Exposed pad connector STEVAL-WESU1 gives the possibility to reduce form factor by cutting PCB area hosting USB connector and expansion connector (see cutting line in 8). USB feature will be accessible by exposed pads on the bottom of the PCB (8). Firmware upgrade will be possible only over the air or via USB DFU. Figure 8: STEVAL-WESU1 Exposed Pads 1: USB DP 2: USB 5V 3: GND 4: USB DM 5: TP512 Expansion PIN 4 test point DRAFT 2.5.5 uFL connector The uFL connector U201 (not mounted) is connected to BLUENRG-MS RF path through C206 (not mounted). By soldering a 51pF capacitor and desoldering L204, the uFL connector RF path can be activated, useful for debug purposes. 2.6 Buttons and LEDs The STEVAL-WESU1 board has 2 LEDs and only one button for user operations. 12/22 Version 0.1 STMicroelectronics Confidential ST application note template Error! No text of specified style in document. 3 Formal notices required by the U.S. Federal Communications Commission ("FCC") Model: STEVAL-WESU1 FCC ID: S9NWESU1 Any changes or modifications to this equipment not expressly approved by STMicroelectronics may cause harmful interference and void the users authority to operate this equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. For Class A Digital Devices This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. For Class B Digital Devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference's by one or more of the following measures:
DRAFT Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and the receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. STMicroelectronics Confidential Rev 0.1 13/22 Error! No text of specified style in document. ST application note template 4 Formal notices required by the Industry Canada
("IC") Model: STEVAL-WESU1 IC: 8976C-WESU1 English:
This Class A or B digital apparatus complies with Canadian CS-03. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. French:
Cet appareil numrique de la classe A ou B est conforme la norme CS-03 du Canada. Les changements ou les modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de l'utilisateur pour actionner l'quipement. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. 'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. DRAFT 14/22 Version 0.1 STMicroelectronics Confidential Error! No text of specified style in document. ST application note template 5 Board schematic and bill of material This section contains the bill of material and layout of the STEVAL-WESU1 5.1 Bill of material Item Q.ty Reference Part/Value 1 ANT1 1 CN500 2.4 GHz Micro_USB _AB BOM STEVAL-WESU1 Voltage
/Ampere
/Ohm Type /
Additional Notes Chip Antenna Tolerance Package Manufacturer Manufacturer Code SMD Pulse W3008C Molex 47590-0001 1uF 6.3V Ceramic X5R 10%
SMD 0402 Murata GRM155R60J105KE19D DRAFT Ceramic X5R SMD 0201 100nF 10%
16V 2 C118,C119 10pF 10uF 6.3V 25V Ceramic X5R Ceramic C0G, NP0 20%
0.5pF SMD 0402 TDK C1005X5R0J106M050BC SMD 0201 TDK C0603C0G1E100D030BA Murata GRM033R61C104KE84D STMicroelectronics Confidential Rev 0.1 15/22 1 2 3 4 5 6 C110,C200,C2 16,C401,C411 C111,C112,C1 13,C114,C115, C116,C201,C2 19,C222,C225, C228,C302,C3 04,C305,C306, C307,C308,C3 09,C406,C407, C412,C504,C5 05 C117,C303,C4 00,C404 5 23 4 More Info Error! No text of specified style in document. ST application note template 7 1 C206 51pF NOT MOUNT 50V Ceramic C0G 10%
SMD 0402 Murata GRM1555C1H510GA01D 8 2 C212,C213 12p 50V CH 0.1pF SMD 0201 Murata GRM0335C1H120GA01 9 2 C214,C221 100p 16V Ceramic X7R 10%
SMD 0201 Murata GRM033R71C101KD01D 10 2 C223,C224 Not Mount Not Mount Not Mount Not Mount SMD 0402 Murata Not Mount 11 2 C226,C227, C22,C23 15p 25V C0G 0.1pF SMD 0201 Murata GJM0336C1E150FB01D 12 13 14 15 16 17 18 19 20 21 22 23 1 C229 150n 2 C402,C403 2.2uF C405,C408,C4 09 3 10nF 6.3V 6.3V 10V Ceramic X5R Ceramic X5R(EIA) 10%
20%
SMD 0402 Murata GRM155R60J154KE01D SMD0402 Murata GRM155R60J225ME95D Ceramic X7R 10%
SMD 0201 Murata GRM033R71A103KA01D 1 C410 1 C500 1 C501 1 D401 1 D500 1 D501 1 D502 1 1 J500 J501 220nF 16V Ceramic X7R 10%
SMD 0402 10V 50V 47uF 4.7nF Ceramic X7R DRAFT Ceramic X5R SMD 0402 SMD 0805 ST0201 10%
20%
RED LED LED Murata Murata TDK VISHAY VISHAY ST ST GRM155R71C224KA12D GRM155R71H472KA01D C2012X5R1A476M125AC VLMS1500-GS08 VLMW1500-GS08 ESDALC6V1-1U2 ST-SUPPLY ESDA&P60-1U1M ST-SUPPLY QFN THR 1.27 mm 2x5 SAMTEC FTSH-105-01-F-D-K SMT 3W 1.2 Molex 78171-0003 WHITE ESDALC6V1
-1U2 ESDA7P60-
1U1M SWD/JTAG CON3 16/22 Version 0.1 STMicroelectronics Confidential Mandatory Use Manuf.Code Marked Mandatory Use Manuf.Code Marked Mandatory Use Manuf.Code Marked Mandatory Use Manuf.Code Marked Mandatory Use Manuf.Code Marked ST application note template Error! No text of specified style in document. 1 1 L203 L204 10uH 0R OHM 3.9nH 1.5 Ohm 215 mA 0 10k 0 0-NOT MOUNT 2K 1R 1 3 4 10 5 5 L205,L206 L401,L402,L40 3 R113,R309,R4 05,R506 R116,R117,R1 19,R120,R121, R122,R123,R2 00,R201,R501 R301,R302,R3 03,R307,R308 R114,R118,R3 04,R305,R306 1 R400 1 R401 1 R402 2 R403-R408 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 mm pitch 20%
SMD 0805 Murata LQM21FN100M70L 0,1nH SMD 0402 Murata TBD 0,3nH SMD 0201 Murata LQG15HN3N9SO2D Mandatory Use Manuf.Code Marked Mandatory Use Manuf.Code Marked SMD 0201 Murata BLM03BD471SN1D SMD 0201 ANY ANY 1%
1%
1%
1%
1%
1%
SMD 0201 ANY SMD 0201 ANY SMD 0201 SMD 0201 SMD 0201 ANY ANY ANY ANY ANY ANY ANY ANY ANY ANY NTCS0402E3103FLT ANY ANY ANY ANY ANY 1%
60 - 0.05W 1K 10K NTC -
NOT MOUNT DRAFT SMD 0201 SMD 0402 SMD 0201 SMD 0201 1%
1%
1%
1%
1M 33K SMD 0201 ANY ANY Vishay ANY ANY 1M 100K 100 0.05 SW 1%
1%
1%
1%
SMD 0201 SMD 0201 SMD 0201 ANY ANY ANY SMD 0402 WELWYN LRCS0402-0R05FT5 Omron B3U-3000P 1 R404 1 R412 1 R413 1 R500 2 R502,R503 1 R504 1 R505 1 SW500 STMicroelectronics Confidential Rev 0.1 17/22 Error! No text of specified style in document. ST application note template PUSHBUTT ON-DPST U.FL connector -
NOT MOUNT STM32L15 1VEY6 BLUENRG-
MS BALF-NRG-
01D3 44 45 46 47 1 U201 1 U100 1 U200 1 U202 48 1 U301 LPS25HB 49 1 U302 LSM6DS3 1 U303 LIS3MDL 1 U400 STNS01 50 51 52 53 54 1 U401 1 U402 1 U502 50 Ohm - 6 Ghz SMD Coaxial Connector WLCSP104 VFQPN32 5x5 mm FLIP CHIP 4 ball HLGA-10L
(2.5 x 2.5x 0.76 mm) LGA-14L
(2.5x3x0.83 mm) VFLGA-12
(2.0x2.0x1.0 mm) DFN12L (3x3 mm) CSP (1.4 x 2.0 mm) SOT666 STC3115 STLQ015XG 30R USBULC6-
2M6 NX2012SA 32k EXS00A-
MU00389 NX2016SA 24MHZ EXS00A-
CS05544 NX2016SA 32MHz EXS00A-
CS06644 uQFN DRAFT Y2, Y201 Y101 55 2 56 1 57 1 Y202 NDK 18/22 Version 0.1 STMicroelectronics Confidential SMT Hirose U.FL-R-SMT-1(10) ST ST ST ST ST ST ST ST ST ST NDK NDK STM32L151VEY6 ST-SUPPLY BLUENRG-MSQTR ST-SUPPLY BALF-NRG-01D3 ST-SUPPLY LPS25HB ST-SUPPLY LSM6DS3 ST-SUPPLY LIS3MDL STNS01 STC3115 ST-SUPPLY ST-SUPPLY ST-SUPPLY STLQ015XG30R ST-SUPPLY USBULC6-2M6(uQFN) ST-SUPPLY ST application note template Error! No text of specified style in document. 5.2 Schematic DRAFT STMicroelectronics Confidential Rev 0.1 19/22 Error! No text of specified style in document. ST application note template 6 Revision history Table 1: Table Title Revision Date of modification Description of modification 0.2 0.3 0.4 July 15 July 15 July 15 Initial draft Modified version Changed name in STEVAL-WESU1 DRAFT 20/22 Version 0.1 STMicroelectronics Confidential ST application note template Error! No text of specified style in document. STMicroelectronics Confidential DRAFT Rev 0.1 21/22 Error! No text of specified style in document. ST application note template Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (ST) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to STs terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN STS TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. DRAFT 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies www.st.com Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. 22/22 Version 0.1 STMicroelectronics Confidential
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2015-12-18 | 2402 ~ 2480 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2015-12-18
|
||||
1 | Applicant's complete, legal business name |
ST Microelectronics S.R.L.
|
||||
1 | FCC Registration Number (FRN) |
0003770575
|
||||
1 | Physical Address |
Via C. Olivetti,2
|
||||
1 |
Agrate Brianza, N/A 20864
|
|||||
1 |
Italy
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
V******@tuvam.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
S9N
|
||||
1 | Equipment Product Code |
WESU1
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
P****** E********
|
||||
1 | Title |
Design Manager
|
||||
1 | Telephone Number |
+3903********
|
||||
1 | Fax Number |
+3903********
|
||||
1 |
p******@st.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 04/20/2016 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Evaluation Board | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Single Modular Approval | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Modular Approval. Power listed is conducted. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Compliance Certification Services Inc.
|
||||
1 | Name |
H******** L******
|
||||
1 | Telephone Number |
886-2******** Extension:
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
h******@sgs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2402.00000000 | 2480.00000000 | 0.0033000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC