SPWF04SA SPWF04SC Serial-to-Wi-Fi b/g/n intelligent modules Preliminary Datasheet 13.7 dBm @ 54 Mbps OFDM RX sensitivity
-96.0 dBm @ 1 Mbps DSSS
-74.5 dBm @ 54 Mbps OFDM 16 configurable GPIOs available UART and SPI interface to host system Advanced low-power modes Standby with RTC: 0.8mA (TBC) Sleep connected (DTIM=1): 19 mA RX traffic 113 mA typical TX traffic 248 mA typical @ 18 dBm Features 2.4 GHz IEEE 802.11 b/g/n transceiver Simple AT command set host interface through STM32 ARM Cortex-M4, with 256 KB RAM UART and 2 MB Flash memory Integrated TCP/IP protocol stack 2 (TBC) simultaneous TCP or UDP clients and 2 (TBC) socket server supporting up to TLS 1.2, including common encryption algorithms: AES
(128, 256), hash (MD5, SHA-1, SHA-
256) and public key algorithms (RSA, ECC) Small form factor: 26.92 x 15.24 x 2.35 mm Single voltage supply (3.3 V typical) Multiple antenna options:
Integrated antenna (SPWF04SA versions) Integrated u.fl connector (SPWF04SC versions) Industrial temperature range: -40 C to 85 C Web server supporting dynamic web pages WEP/WPA/WPA2 personal and enterprice security System modes: Station, IBSS, and miniAP miniAP easily provisioned (SSID, PWD) Fast Wi-Fi reassociation after reset Firmware update via UART and Over The Air FCC/CE/IC/SRRC certified RoHS compliant Surface mount PCB module Applications Smart appliances
(FOTA TX power 18.3 dBm @ 1 Mbps DSSS Industrial control and data acquisition Home automation and security systems Wireless sensors Cable replacement Medical equipment Machine-to-machine communication April 2016
. DocID025635 Rev 7 1/18 www.st.com Description SPWF04SA, SPWF04SC 1 Description The SPWF04SA and the SPWF04SC intelligent Wi-Fi modules represent a plug-and-play and standalone 802.11 b/g/n solution for easy integration of wireless Internet connectivity features into existing or new products. Configured around a single-chip 802.11 transceiver with integrated PA and comprehensive power management subsystem, and an STM32 microcontroller with an extensive GPIO suite, the modules also incorporate timing clocks and voltage regulators. Two different options exist based on the integrated Flash memory. The module is available either configured with an embedded micro 2.45 GHz highly-efficient ISM band antenna (SPWF04SA), or with an u.fl connector for external antenna connection
(SPWF04SC). With low power consumption and ultra-compact (2.7 x 1.5 cm) footprint, the modules are ideal for fixed and mobile wireless applications, as well as challenging battery-operated applications. The SPWF04Sx parts are released with an integrated full featured TCP/IP protocol stack with added web server and additional application service capabilities, such as REST API for accessing files on servers in the cloud and support for dynamic web pages with CGI/SSI functions to easily interact with the module and the host processor over the air. For secure end-to-end communication with the cloud, an SSL/TLS stack is embedded in every module with no licensing charge. See application note AN4683 (TBC) for details. The SW package also includes an AT command layer interface for user-friendly access to the stack functionalities via the UART serial port. For details, see user manual UM1695
(TBC). It is always possible to upgrade the module firmware via UART and Over The Air (FOTA). Inside of the 2 MB extended Flash available on the SPWF04S module, 1 MB of the Flash is dedicated to FW upgrade and to host proprietary files, organized in a file system image, accessible through the integrated web server. FOTA is also possible with the SPWF04Sx module. ST may update the FW provided with the modules at any time. ST recommends that users regularly check for documentation and the current FW version available at www.st.com/wifimodules. 2/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Description Figure 1. Block diagram DocID025635 Rev 7 3/18 General electrical specifications SPWF04SA, SPWF04SC 2 General electrical specifications Table 1. Absolute maximum ratings Parameter Test condition/comment Min. Typ. Max. Unit Voltage supply Vin for 5 V tolerant pins Vin for all other pins Storage temperature range
-
-0.3
-0.3
-0.3
-55
-
4.0 5.5 3.6 V V V 105 C Table 2. Operating conditions and input power specifications(1) Parameter Test condition/comment Min. Typ. Max. Unit Operating temperature range Industrial Input supply voltage 3.3 V supply input
-40 3.1 3.3 85 3.6 3.3 V supply Standby Sleep Low power state TX RX Both the STM32 and the radio are in standby power states The STM32 is in stop power state and the radio is in sleep power state The STM32 is active and the radio is in sleep power state TX power=0 dBm 802.11b TX power=10 dBm TX power=18 dBm TX power=0 dBm 802.11g TX power=10 dBm TX power=18 dBm 802.11b 802.11g 0.8 19 52 236 250 344 210 243 338 105 105 C V mA mA mA mA mA mA mA mA mA mA mA 1. Typical results are at room temperature only. 4/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Digital interface specifications 3 Digital interface specifications Table 3. Digital interface specifications, I/O pins Parameter Test condition/comment Min. Typ. Max. Unit Inputs Outputs VIH VIL VOH VOL IOH=4 mA IOL=4 mA
-
2.3 0 2.4 0 3.6 0.9 3.6 0.4 V V V V DocID025635 Rev 7 5/18 RF characteristics SPWF04SA, SPWF04SC 4 RF characteristics Table 4. RF characteristics Parameter Test condition/comment Min. Typ. Max. Unit RX sensitivity(1) 11b, 1 Mbps 11b, 2 Mbps 11b, 5.5 Mbps 11b, 11 Mbps 11g, 9 Mbps 11g, 18 Mbps 11g, 36 Mbps 11g, 54 Mbps 11n, MCS1, 13 Mbps 11n, MCS3, 26 Mbps 11n, MCS5, 52 Mbps 11n, MCS7, 65 Mbps Channel-to-channel de-sensitivity CH1 to 14 Maximum input signal CH7 11Mbps 9 Mbps Adjacent channel rejection 54 Mbps MCS1 MCS7 11b, 1 Mbps 11b, 11 Mbps TX output power (1) 11g, 54 Mbps, 10%PER 11g, 54 Mbps
@ 11b spectral mask 11g, 9 Mbps
@ 11g spectral mask 11g, 54 Mbps EVM = -27 dB, 4.5%
11n, MCS1 11n, MCS7 On-board antenna gain External antenna gain
@ 11n spectral mask EVM = -27 dB Average SG901-1066 average including cable loss 1. Output power and sensitivities are measured with a 50 connection at the antenna port. 6/18 DocID025635 Rev 7
-96
-93
-91
-87
-89.5
-86
-80
-74.5
-86.5
-81.5
-74
-71 1
-20 38 20 4 24 3 18.3 18.3 18.3 13.7 18.3 13.5
-1.2 2.8 dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dB dBm dBc dBc dBc dBc dBc dBm dBm dBm dBm dBm dBm dBi dBi SPWF04SA, SPWF04SC Pinout description 5 Pinout description Signal name GPIO[0]
GPIO[1]
GPIO[2]
GPIO[3]
GPIO[6]
GPIO[4]
GPIO[5]
GPIO[7]
GPIO[8]
GPIO[9]
GPIO[11]
GPIO[12]
GPIO[15]
GPIO[10]
Type I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O GPIO[13]
I/O Table 5. Pinout description Pin number Main function Alternate functions(1) Notes GPIO - general purpose input/output Input pull down and 5V tolerant Input pull down and 5V tolerant Floating and 5V tolerant Input pull down and 5V tolerant Input pull down and 5V tolerant 16 17 19 1 22 18 20 13 4 7 11 12 21 General purpose input/output Restore to factory settings(2) General purpose input/output/ADC General purpose input/output/PWM General purpose input/output General purpose input/output Wake Up/Sleep Inhibit(3) General purpose input/output General purpose input/output General purpose input/output STA/Mini AP Switch/WPS Pushbutton (4) General purpose input/output General purpose input/output/SPI nHostInterrupt General purpose input/output General purpose input/output/DAC Monitoring purpose with no alternate function 5 15 Drives LED, Blinks while running Drives LED, Wi-Fi link up DocID025635 Rev 7 7/18 Pinout description SPWF04SA, SPWF04SC Type I/O I I O I Signal name GPIO[14]
RXD /
MOSI TXD /
MISO CTS / nCS RTS / CLK RESETn 3.3 V Ground LSE HSE SWD I/O SWD CLK GPIO16 GPIO17 GPIO18 SDIO CLK /
SPI CLK SDIO D0 /
SPI MISO SDIO CMD
/ SPI MOSI Ground Paddle Table 5. Pinout description (continued) Pin number Main function Alternate functions(1) 14 8 6 9 10 LED drive, Power up UART pins Reset 3 Reset input Supply pins and paddle 24 23 34 35 26 29 27 28 30 31 32 33 25 Voltage supply Ground Ground Boot loader Boot loader (5) Not available Not available Not available Notes 5V tolerant 5V Tolerant Active low, 5V tolerant 5V tolerant Active low for 5 ms with pull up to 2.5VDC. Not 5V tolerant Decouple with 10uF capacitor Add plenty of ground vias for thermal dissipation and ground return BOOT0 I 2 1. The activation of ALT function depends upon the firmware version or upon the variable configuration. 2. To perform the factory reset of the variables, pin GPIO0 must be high during powerup. 3. GPIO function running when low power mode variable is enabled. 4. Introduced with the release 3.0 of AT Full stack. To enable the STAToMiniAP switch the GPIO[7] needs to be put low together with the HW reset 8/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Pinout description 5. To enable the firmware download, pin BOOT0 needs to be high during power up. RESETn need to be pulled low at least 5 ms to initiate the firmware download sequence. Application guidelines The HOST processor should control the RESETn pin of the module in order to recover from unexpected behavior using the HW reset. DocID025635 Rev 7 9/18 Module reflow SPWF04SA, SPWF04SC 6 Module reflow The SPWF04SA and SPWF04SC are surface mount modules with a 6-layer PCB. The recommended final assembly reflow profiles are indicated below. The soldering phase must be executed with care: in order to prevent an undesired melting phenomenon, particular attention must be paid to the setup of the peak temperature. The following are some suggestions for the temperature profile based on the IPC/JEDEC J-
STD-020C, July 2004 recommendations. Table 6. Soldering values Profile feature PB-free assembly Average ramp-up rate (TSMAX to TP) 3 C/sec max Preheat:
Temperature min. (Ts min.) Temperature max. (Ts max.) Time (Ts min. to Ts max) (ts) Critical zone:
Temperature TL Time TL Peak temperature (TP) 150 C 200 C 60-100 sec 217 C 60-70 sec 240 + 0 C Time within 5 C of actual peak temperature (TP) 10-20 sec Ramp-down rate 6 C/sec Time from 25 C to peak temperature 8 minutes max. Figure 2. Soldering profile 10/18 DocID025635 Rev 7 AM17477v1 SPWF04SA, SPWF04SC Regulatory compliance 7 Regulatory compliance RF compliance The RF certifications obtained are described in Table 7 below. Table 7. RF certification summary Comment FCC ID S9NSPWFS04 On board antenna and external ANTENOVA TITANIS with connector version IC ID 8976C-SPWFS04 On board antenna and external ANTENOVA TITANIS with connector version ETSI Compliant Approved with on board antenna and connector version This radio transmitter IC ID 8976-SPWFS04 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Note:
The TITANIS antenna from ANTENOVA. is the only approved antenna using the u.fl connector version. SPWF04SA, SPWF04SC Regulatory compliance
*Note all data provided in this table are based on the Antenova reference board FCC and IC This module has been tested and complies with the FCC part 15 and IC RSS-247 regulations. These limits are designed to provide reasonable protection against harmful interference in approved installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1. The device must not cause harmful interference. and 2. The device must accept any interference received, including interference that may cause undesired operation. Modifications or changes to this equipment not expressly approved by the party responsible for compliance may render void the user's authority to operate this equipment. The safe user distance, for RF Exposure, is 50mm (in compliance with 447498 D01 General RF Exposure Guidance v06 and RSS-102 Issue 5). Modular approval, FCC and IC
- FCC ID: S9NSPWFS04
-
IC: 8976C-SPWFS04 In accordance with FCC part 15, the modules SPWF04SA and SPWF04SC are listed above as a modular transmitter device. DocID025635 Rev 7 11/18 Regulatory compliance SPWF04SA, SPWF04SC Labeling instructions When integrating the SPWF04SA and SPWF04SC into the final product, it must be ensured that the FCC and IC labeling requirements specified below are satisfied. Based on the Public Notice from FCC, the product into which the ST transmitter module is installed must display a label referring to the enclosed module. The label should use wording like the following:
Contains Transmitter Module
- FCC ID: S9NSPWFS04
-
IC: 8976C-SPWFS04 Any similar wording that expresses the same meaning may also be used. CE This module complies with the following European EMI/EMC and safety directives and standards:
ETSI EN 300 328 V1.8.1:2012 EN 301 489-1 V1.9.2:2011 + EN 301 489-17 V2.2.1:2009 EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013 EN 62479:2010 Figure 3. CE certified SRRC
(T.B.C.) The SPWF04Sx module complies with Chinese SRRC certification. SRRC CMIIT ID: (T.B.D.)
(See the A.1 at the bottom of this document for the French translation) 12/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Package information 8 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Figure 4. Top view of the module shield Shield CE Logo Figure 5. Bottom view of the module Data Matrix Model Series Name zone Board Design Reference FCC and IC ID zone DocID025635 Rev 7 13/18 Package information SPWF04SA, SPWF04SC Figure 6. Wi-Fi module dimensions Note:
An antenna area of 217 x 520 mils must be free of any ground metalization or traces under the unit. The area extending away from the antenna should be free from metal on the PCB and housing to meet expected performance levels. Pin 25 is the required paddle ground and is not shown in this diagram. 14/18 DocID025635 Rev 7 SPWF04SA, SPWF04SC Package information Figure 7. Wi-Fi module footprint PCB design requires a detailed review of the center exposed pad. This pad requires good thermal conductivity. Soldering coverage should be maximized and checked via x-ray for proper design. There is a trade-off between providing enough soldering for conductivity and applying too much, which allows the module to float on the paddle creating reliability issues. ST recommends two approaches, a large center via that allows excess solder to flow down into the host PCB with smaller vias around it, or many smaller vias with just enough space for the viscosity of the chosen solder/flux to allow some solder to flow into the smaller vias. Either of these approaches must result in 60% or more full contact solder coverage on the paddle after reflow. ST strongly encourages PCB layout teams to work with their EMS providers to ensure vias and solder paste designs that will result in satisfactory performance. DocID025635 Rev 7 15/18 Regulatory compliance 9 Ordering information SPWF04SA/C Order codes Description Table 8. Ordering information SPWF04SA Wi-Fi module with integrated antenna, 1 MB of Flash and Wi-Fi full stack SPWF04SC Wi-Fi module with integrated ufl connector, 1 MB of Flash and Wi-Fi full stack Note:
Refer to the user manual for a complete list of features and commands available in the Wi-Fi full stack. Regulatory compliance Dclaration de conformit SPWF04SA/C A.1 Certification FCC Le module SPWF04SA/C a t test et dclar conforme avec la section 15 de la Rglementation FCC. Ces limitations sont stipules afin de procurer une protection raisonnable contre les interfrences gnantes dans les installations approuves. Cet appareil gnre, utilise et diffuse des ondes radio et, sil nest pas install et utilis en conformit avec les instructions dont il fait lobjet, peut causer des interfrences gnantes sur les communications radio. Il ny a cependant pas de garantie quune interfrence ne se produira pas dans une installation particulire. Cet appareil est en conformit avec la section 15 des rglements FCC. Lutilisation est soumise aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interfrences nocives, et (2) Cet appareil doit supporter toute interfrence reue, y compris des interfrences qui peuvent provoquer un fonctionnement non dsir. Tout changement ou modification fait(e) cet appareil et non expressment approuv(e) par STMicroelectronics peut annuler lautorisation pour lutilisateur de faire fonctionner lappareil. Approbation du module FCC ID: S9NSPWFS04 Conformment la section 15 des rglements FCC, le module SPWF04SA/C est rpertori comme un dispositif metteur modulaire. Ce module nest valu que pour une utilisation autonome. Les produits finis incorporant plusieurs metteurs doivent tre conformes la colocation et aux exigences d'exposition RF en concordance avec les procdures FCC multi-metteurs. Dautres metteurs fonctionnant dans des dispositifs portables exposs aux RF (par exemple, situs moins de 20 cm des personnes avec dispositifs portatifs ou ports contre le corps) peuvent ncessiter d'une approbation spare. Instructions d'tiquetage Lors de l'intgration du module SPWF04SA/C dans le produit final, le fabricant doit sassurer que les exigences en matire d'tiquetage de la FCC sont satisfaites . Une dclaration doit tre place sur ltiquette extrieure du produit final indiquant que le produit comprend un module certifi. L'tiquette doit comporter les informations suivantes
(ou une mention analogue que recouvre la mme notion):
OU Ce produit contient FCC ID: S9NSPWFS04 Contient FCC ID: S9NSPWFS04 Le sous-traitant doit inclure les noncs suivants sur ltiquette extrieure du produit final moins que le produit ne soit trop petit (par exemple moins de 4 x 4 pouces):
Cet appareil est en conformit avec la section 15 des rglements FCC . Lutilisation est soumise aux deux conditions suivantes:
(1) cet appareil ne doit pas causer d'interfrences nocives, et
(2) Cet appareil doit supporter toute interfrence reue, y compris des interfrences qui peuvent provoquer un fonctionnement non dsir. A.1.1 A1 DocID temporary Rev1 Regulatory compliance SPWF04SA, SPWF04SC A.1.2 Instructions pour lutilisation du produit La prsente section concerne les produits finis contenant le module SPWF04SA/C, assujettis aux normes FCC. Le manuel du produit final doit contenir la dclaration suivante (ou une mention analogue que recouvre la mme notion):
Avertissement: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorisation de l'utilisateur de faire fonctionner cet quipement. (Section 15.21) Dans le cas o le produit finis dun fabriquant OEM rentre dans les limites de la Classe B (rsidentiel), les noncs suivants doivent tre inclus dans le manuel du produit finis:
Remarque : Cet quipement a t test et dclar conforme aux limitations prvues dans le cadre de la classe B des appareils numriques, dfinies par la section 15 du rglement de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre toute interfrence dangereuse issue d'une installation rsidentielle. Cet quipement produit, utilise et peut mettre de l'nergie radio lectrique et, s'il n'est pas install et utilis conformment aux prsentes instructions, peut causer des interfrences nuisibles aux communications radio. Cependant, il se peut que des interfrences se produisent dans une installation particulire. Si cet appareil cause des interfrences nuisibles la rception des signaux de radio ou de tlvision, ce qui peut tre dtermin en allumant et en teignant l'appareil, on encourage l'utilisateur d'essayer de corriger ces interfrences par l'un des moyens suivants:
Rorienter ou repositionner l'antenne de rception. Augmenter la distance sparant lquipement du rcepteur. Connecter lquipement une prise appartenant un circuit diffrent de celui sur lequel le rcepteur est connect. Consulter le revendeur ou un technicien radio/TV expriment pour obtenir de laide. Dans le cas o le produit fini dun sous-traitant rentre dans les limites imposes aux appareils numriques de classe A, les noncs suivants doivent tre inclus dans le manuel du produit finis:
REMARQUE : Cet appareil a t test et certifi conforme aux spcifications d'un appareil lectronique de classe A (class A digital device), conformment la partie 15 du rglement de la FCC. Ces contraintes sont destines fournir une protection raisonnable contre les interfrences nuisibles quand l'appareil est utilis dans une installation commerciale. Cet quipement produit, utilise et peut mettre de l'nergie radio lectrique et, s'il n'est pas install et utilis conformment aux prsentes instructions, peut causer des interfrences nuisibles aux communications radio. L'utilisation de cet appareil dans une installation rsidentielle peut entraner des interfrences nuisibles et l'utilisateur devra corriger les interfrences ses propres frais. Regulatory compliance A.2 Certification IC (a) SPWF04SA, SPWF04SC Le module SPWF04SA/C a t test et dclar conforme avec la Rglementation IC CNR-210. Ces limitations sont stipules afin de procurer une protection raisonnable contre les interfrences gnantes en installations approuves. Cet appareil gnre, utilise et diffuse des ondes radio et, sil nest pas install et utilis en conformit avec les instructions dont il fait lobjet, peut causer des interfrences gnantes sur les communications radio. Il ny a cependant pas de garantie quune interfrence ne se produira pas dans une installation particulire. Ce produit rpond aux exigences de la norme CNR-210 d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes:
(1) cet appareil ne doit pas causer d'interfrences nocives, et
(2) Cet appareil doit supporter toute interfrence reue, y compris des interfrences qui peuvent provoquer un fonctionnement non dsir. Tout changement ou modification fait(e) cet appareil et non expressment approuv(e) par STMicroelectronics peut annuler lautorisation pour lutilisateur de faire fonctionner lappareil. Approbation du module IC: 8976C-SPWFS04 Conformment IC CNR-210, le module SPWF04SA/C est rpertori comme un dispositif metteur modulaire Ce module nest valu que pour une utilisation autonome. Les produits finis incorporant plusieurs metteurs doivent tre conformes la colocation et aux exigences d'exposition RF en concordance avec les procdures FCC multi-metteurs. Dautres metteurs fonctionnant dans des dispositifs portables exposs aux RF (par exemple, situs moins de 20 cm des personnes avec dispositifs portatifs ou ports contre le corps) peuvent ncessiter d'une approbation spare. A.2.1 Instructions d'tiquetage Lors de l'intgration du module SPWF04SA/C dans le produit final, le fabricant doit sassurer que les exigences en matire d'tiquetage de la IC sont satisfaites . Une dclaration doit tre place sur ltiquette extrieure du produit final indiquant que le produit comprend un module certifi. L'tiquette doit comporter les informations suivantes
(ou une mention analogue que recouvre la mme notion):
Contient IC ID: 8976C-SPWFS04 OU Ce produit contient IC ID: 8976C-SPWFS04 Le sous-traitant doit inclure les noncs suivants sur ltiquette extrieure du produit final moins que le produit ne soit trop petit (par exemple moins de 4 x 4 pouces):
Cet appareil est en conformit aux normes IC. Lutilisation est soumise aux deux conditions suivantes:
(1) cet appareil ne doit pas causer d'interfrences nocives, et
(2) Cet appareil doit supporter toute interfrence reue, y compris des interfrences qui peuvent provoquer un fonctionnement non dsir Regulatory compliance A.2.2 Instructions pour lutilisation du produit SPWF04SA, SPWF04SC La prsente section concerne les produits finis contenant le module SPWF04SA/C, assujettis aux normes IC. Le manuel du produit final doit contenir la dclaration suivante
(ou une mention analogue que recouvre la mme notion):
Avertissement: Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorisation de l'utilisateur de faire fonctionner cet quipement. (CNR-210) Dans le cas o le produit finis dun fabriquant OEM rentre dans les limites de la Classe B (rsidentiel), les noncs suivants doivent tre inclus dans le manuel du produit finis:
Remarque : Cet quipement a t test et dclar conforme aux limitations prvues dans le cadre de la classe B des appareils numriques, dfinies par la norme CNR-210 d'Industrie Canada. Regulatory compliance SPWF04SA, SPWF04SC Ces limites sont conues pour fournir une protection raisonnable contre toute interfrence dangereuse issue d'une installation rsidentielle. Cet quipement produit, utilise et peut mettre de l'nergie radio lectrique et, s'il n'est pas install et utilis conformment aux prsentes instructions, peut causer des interfrences nuisibles aux communications radio. Cependant, il se peut que des interfrences se produisent dans une installation particulire. Si cet appareil cause des interfrences nuisibles la rception des signaux de radio ou de tlvision, ce qui peut tre dtermin en allumant et en teignant l'appareil, nous encourageons l'utilisateur essayer de corriger ces interfrences par l'un des moyens suivants:
Rorienter ou repositionner l'antenne de rception. Augmenter la distance sparant lquipement du rcepteur. Connecter lquipement une prise appartenant un circuit diffrent de celui sur lequel le rcepteur est connect. Consulter le revendeur ou un technicien radio/TV expriment pour obtenir de laide. Dans le cas o le produit finis dun fabriquant OEM rentre dans le cadre des limites imposes aux appareils numriques de classe A, les noncs suivants doivent tre inclus dans le manuel du produit finis:
REMARQUE: Cet appareil a t test et certifi conforme aux spcifications d'un appareil lectronique de classe A (class A digital device), conformment la norme CNR-210 d'Industrie Canada. Ces contraintes sont destines fournir une protection raisonnable contre les interfrences nuisibles quand l'appareil est utilis dans une installation commerciale. Cet quipement produit, utilise et peut mettre de l'nergie radio lectrique et, s'il n'est pas install et utilis conformment aux prsentes instructions, peut causer des interfrences nuisibles aux communications radio. L'utilisation de cet appareil dans une installation rsidentielle peut entraner des interfrences nuisibles et l'utilisateur devra corriger les interfrences ses propres frais. A.3 Certification CE Le module SPWF04SA/C a obtenu une certification de conformit aux normes suivantes :
EN 300 328 V1.8.1 :2012 EN 300 328 V1.9.1 :2015 EN 301 489-17 V2.2.1 :2009 EN 301 489-1 V1.9.2:2011 EN 62479 :2010 EN60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2 :2013 Le module est certifi CE:
Regulatory compliance SPWF04SA, SPWF04SC A1 SPWF04SA, SPWF04SC Revision history 10 Revision history Table 9. Document revision history Date Revision Changes 27-Apr-2016 1 Initial release. DocID025635 Rev 7 17/18 SPWF04SA, SPWF04SC IMPORTANT NOTICE PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (ST) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to STs terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. 2016 STMicroelectronics All rights reserved 18/18 DocID025635 Rev 7