FCC ID: YJ7CMCR001B Bluetooth Speaker

Wireless Certifications and Safety Information This device is either CAN ICES-3(B)/NMB-3(B)or CAN ICES-

5(B)/NMB-5(B)compliant. This device complies with Part 15 of the FCC Rules and Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesiredoperation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:

1)Reorient or relocate the receivingantenna, 2) Increase the separation between the equipment andreceiver, 3) Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected or 4) Consult the dealer or an experienced radio/TV technician forhelp. Changes or modifications to this equipment not expressly approved by the manufacturer could void the users authority to operate the device. FINAL PAGE SIZE: 8.5" x 5.5" (half letter) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum

(or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successfulcommunication. To comply with FCC and Industry Canada RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operated in conjunction with any other antenna or transmitter. For Bluetooth Products When traveling on airlines, be sure to comply with the airline restrictions on usage of personal electronic devices and Bluetooth. The out of range alert feature has been designed to act as an aid to warn against products getting misplaced or stolen. It is not a securitysystem. The connectivity range is up to 100 feet (30.5 meters) depending on environment andlocation. The shortwave radio frequency signals of a Bluetooth device may impair the operation of other electronic and medical devices (such as pacemakers or hearing aids). NOTE: The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth, SIG, Inc. and any use of such marks is under license. Other trademarks and trade names are those of their respectiveowners. This product complies with these standards when operated with a 6 foot (1.8 meters) or shorter extensioncord. Stanley Black and Decker, 701 East Joppa Road, Towson, MD 21286 www.stanleyblackanddecker.com

(FEB19) Part No. N591662 Copyright 2018, 2019 Homologation du matriel sans fil et informations scurit Cet appareil est conforme la norme CAN ICES-3(B)/NMB-

3(B) ou CAN ICES-5(B)/NMB-5(B). Cet appareil est conforme au paragraphe 15 du rglement du FCC et la (aux) norme(s) RSS exempt(s) de licence dIndustrie Canada. Son utilisation est sujette aux deux conditions suivantes : 1) Ce dispositif ne doit pas causer dinterfrences nuisibles; et 2) Ce dispositif doit accepter toute interfrence reue, y compris toute interfrence pouvant causer un fonctionnementindsirable. Cet quipement a t test et jug conforme aux limites propres aux appareils numriques de Classe B, conformment au Paragraphe 15 du rglement du FCC. Ces limites sont destines offrir une protection raisonnable contre les interfrences nuisibles dune installation rsidentielle. Cet quipement produit, utilise et peut maner des ondes radiofrquences qui, sil nest pas install et utilis conformment aux directives, pourront causer des interfrences nuisibles aux communications radio. Cependant, en fonction des installations ralises, labsence dinterfrences nest pas garantie. Si cet quipement cause des interfrences nuisibles la rception radio ou tlvision (ce qui peut tre dtermin par la mise sous/hors tension de cet quipement) lutilisateur est encourag tenter de corriger ces interfrences en prenant lune ou plusieurs des mesures suivantes: 1)Rorienter lantenne de rception ou en changer lemplacement, 2)Augmenter la distance entre lquipement et le rcepteur, 3)Brancher lquipement une prise situe sur un circuit diffrent de celui sur lequel le rcepteur est connect, ou 4) Contacter un revendeur ou consulter un technicien radio/tlqualifi. Tout changement ou toute modification lappareil qui ne serait pas expressment approuv par le fabricant pourra annuler les droits de lutilisateur employer cet quipement. Conformment aux rglementions dIndustrie Canada, cet metteur radio ne peut fonctionner quavec une antenne dont le type et le gain maximal (ou dune valeur moindre) sont homologus par Industrie Canada pour cet metteur. Pour rduire toute interfrence radio potentielle pouvant affecter les autres utilisateurs, le type dantenne et ses gains devraient tre choisis de faon ce que la puissance isotrope rayonne quivalente ne soit pas suprieure aux limites permettant lacommunication. Afin de se conformer aux limites dexposition aux RF de FCC et Industrie Canada pour la population gnrale/lexposition non contrle, une ou plusieurs antennes utilises pour cet metteur doivent tre installes afin doffrir une distance de sparation dau moins 20 cm de toutes les personnes et doivent ne pas tre situes au mme endroit ou utilises conjointement tout autre antenne ou metteur. Pour les produits BluetoothMD Avant de voyager en avion, sassurer de suivre les restrictions des compagnies ariennes quant lutilisation dappareils lectroniques et BluetoothMDpersonnels. La fonctionnalit dalarme hors plage a t conue pour servir aider alerter en cas de perte ou vol de produits. Ce nest pas un systme de scurit. La plage de connectivit peut aller jusqu 30.5 meters (100 pieds) en fonction de lenvironnement et des lieux. Les signaux de radiofrquences ondes courtes dun appareil BluetoothMD pourront affecter les oprations dautres appareils lectroniques ou mdicaux (comme les stimulateurs cardiaques ou les appareils acoustiques). REMARQUE: le terme et les logos BluetoothMD sont des marques dposes appartenant BluetoothMD, SIG, Inc. et toute utilisation de ces marques est autorise par licence. Toute autre marque de commerce et appellation commerciale reste la proprit de leurs propritairesrespectifs. Ce produit est conforme ces standards lorsquil est utilis avec un cordon de 1m 80 (6pi) oumoins. Certificaciones inalmbricas e informacin de seguridad Este dispositivo cumple con CAN ICES-3(B)/NMB-3(B)o con CAN ICES-5(B)/NMB-5(B). Este dispositivo cumple con la Seccin 15 de las normas de la Comisin Federal de Comunicaciones (FCC) y las normas RSS de exencin de licencia del Ministerio de Industria de Canad. Su funcionamiento est sujeto a las dos siguientes condiciones: 1) Este dispositivo no puede causar interferencia daina, y 2) Este dispositivo debe aceptar cualquier interferencia que reciba, incluyendo aquella interferencia que podra producir un funcionamiento no deseado. Este equipo ha sido probado y se ha demostrado que cumple con los lmites establecidos para dispositivos digitales de ClaseB, de conformidad con la Seccin 15 de las Normas de la FCC. Estos lmites estn diseados para ofrecer un nivel razonable de proteccin contra la interferencia daina en instalaciones residenciales. Este equipo genera, utiliza y puede emitir energa de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones proporcionadas, puede producir una interferencia daina a la comunicacin radial. Sin embargo, no existen garantas de que no ocurra interferencia alguna en una instalacin en particular. Si este equipo produce interferencia daina a la recepcin radial o de televisin, lo que puede determinarse al apagar y volver a encender el equipo, se pide al usuario que corrija la interferencia implementando una o ms de las siguientesmedidas: 1) Cambie la orientacin o el lugar donde est ubicada la antena receptora, 2) Aumente el espacio que separa al equipo del receptor, 3) Conecte el equipo a una toma de corriente que est en un circuito diferente al circuito al que est conectado el receptor, o 4) Consulte con el distribuidor o con un tcnico de radio y televisin con experiencia que pueda ayudarle. Los cambios o modificaciones que no estn aprobados expresamente por el fabricante podran anular la autorizacin del usuario para utilizar el dispositivo. Segn el reglamento del Ministerio de Industria de Canad, este transmisor de radio puede funcionar solamente con una antena del tipo y de la mxima (o menor) ganancia aprobados para el transmisor por el Ministerio de Industria de Canad. Para reducir la posible interferencia radioelctrica a otros usuarios, el tipo de antena y su ganancia deberan elegirse de manera que la potencia isotrpica radiada equivalente (p.i.r.e.) no sea mayor que la necesaria para una comunicacinsatisfactoria. Para cumplir con los lmites de exposicin a radiofrecuencia de FCC e Industry Canada para la poblacin general/

exposicin no controlada, la(s) antena(s) utilizada(s) para este transmisor debe(n) instalarse para proporcionar una distancia de separacin de por lo menos 20 cm de todas las personas y no debe ubicarse ni utilizarse junto con cualquier otra antena o transmisor. Para productos con Bluetooth Al viajar en avin, asegrese de cumplir con las restricciones de las lneas areas acerca del uso de dispositivos electrnicos personales y Bluetooth. La funcin de alerta de fuera de alcance ha sido diseada para servir de ayuda para evitar la prdida o robo de productos. No es un sistema de seguridad. El rango de conectividad es de hasta 30.5 m (100 pies) dependiendo del entorno y la ubicacin. Las seales de radiofrecuencia de onda corta de un dispositivo Bluetooth pueden afectar el funcionamiento de otros dispositivos mdicos y electrnicos (como marcapasos o audfonos). NOTA: La marca denominativa y los logotipos de Bluetooth son marcas registradas propiedad de Bluetooth, SIG, Inc. y todo uso de dichas marcas se hace bajo licencia. Otras marca y nombres comerciales son de sus respectivospropietarios. Este producto cumple con estas normas cuando se pone en funcionamiento con un alargador de 1.82 m (6 pies) o mscorto.

Kirwan Magdamo Lead Project Engineer 701 East Joppa Road, Towson, MD 21286 T (410) 716 3563 Authority to Act as Agent Date: August 16, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:

Kimberly Colbert is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge

(47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: April 8, 2024 By:

(Signature1) Kirwan Magdamo

(Print name) Title:

Lead Project Engineer 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. On behalf of: Stanley Black & Decker

(Company Name) Telephone:

410-716-3563

Kirwan Magdamo Lead Project Engineer 701 East Joppa Road, Towson, MD 21286 T (410) 716 3563 Request for Confidentiality Date: August 16, 2023 Subject: Confidentiality Request for: YJ7CMCR001B and 9082A-CMCR001B Pursuant to FCC 47 CFR 0.457(d) and 0.459 and/or IC RSP-100, Section 12.4, the applicant requests that a part of the subject application(s) be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent

Permanent *1 Permanent Permanent Permanent Permanent

Permanent *1 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Stanley Black & Decker has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __ (specify number of days not to exceed 180)2___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. Short Term Confidentiality for Industry Canada Applications:

Starting May 2022, ISED will recognize short term confidentiality on certain exhibits until the intended date of marketing. The applicant requests the exhibits selected above as short term confidential be withheld from public view until:

(specify ISED expiration date / date of marketing) . Sincerely, By:

(Signature/Title3) Kirwan Magdamo

(Print name) 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Kirwan Magdamo Lead Project Engineer 701 East Joppa Road, Towson, MD 21286 T (410) 716 3563 Certification Application Attestation Statements Date: August 16, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:

Statement for 47 CFR section 2.911(d)(5)(i) Stanley Black & Decker certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: <N/A>

Statement for 47 CFR section 2.911(d)(5)(ii) _Stanley Black & Decker (the applicant) certifies that, as of the date of the filing of this application, the applicant is not identified on the Covered List as an entity producing covered equipment. Thank you, By:

(Signature2) Kirwan Magdamo

(Print name) 1 - The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead. Title:

Lead Project Engineer Company:

Stanley Black & Decker Telephone: 410-716-3563

Kirwan Magdamo Lead Project Engineer 701 East Joppa Road, Towson, MD 21286 T (410) 716 3563 U.S. Agent Designation for Service of Process TO:

American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification Section 2.911(d)(7) Information This letter is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information changes. Applicant Company name: Stanley Black & Decker FRN #: 0019980119 Grantee Code: YJ7 Contact Name: Kirwan Magdamo Street Address: 701 East Joppa Road City/Province/Zip: Towson, MD 21286 Telephone No: 410-716-3563 Email: Kirwan.Magdamo@sbdinc.com Applicant Signature1:

Date: August 9, 2023 Signed by (Printed Name/Title): Kirwan Magdamo, Lead Project Engineer, Stanley Black & Decker 1 - Letters must be placed on appropriate letterhead. The signee for the applicant must be one of the following: Applicant (grantee) contact of record in the FCCs authorization system, or authorized officers or employee of the applicant (grantee).