FCC ID: YJ7DCR008 Bluetooth Speaker

DCE042 Tool Connect Chip Wireless Certifications and Safety Information This device is either CAN ICES-3(B)/NMB-3(B)or CAN ICES-5(B)/

NMB-5(B)compliant. This device complies with Part 15 of the FCC Rules and Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesiredoperation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures: 1)Reorient or relocate the receivingantenna, 2) Increase the separation between the equipment andreceiver, 3) Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected or 4) Consult the dealer or an experienced radio/TV technician forhelp. Changes or modifications to this equipment not expressly approved by the manufacturer could void the users authority to operate the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successfulcommunication. To comply with FCC and Industry Canada RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 5mm in the United States and 10mm in Canada from all persons and must not be co-located or operated in conjunction with any other antenna or transmitter. For Bluetooth Products When traveling on airlines, be sure to comply with the airline restrictions on usage of personal electronic devices and Bluetooth. The out of range alert feature has been designed to act as an aid to warn against products getting misplaced or stolen. It is not a securitysystem. The connectivity range is up to 100 feet (30.5 meters) depending on environment andlocation. The shortwave radio frequency signals of a Bluetooth device may impair the operation of other electronic and medical devices

(such as pacemakers or hearing aids). NOTE: The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth, SIG, Inc. and any use of such marks is under license. Other trademarks and trade names are those of their respectiveowners. This product complies with these standards when operated with a 6 foot (1.8 meters) or shorter extensioncord. Stanley Black and Decker, 701 East Joppa Road, Towson, MD 21286 www.stanleyblackanddecker.com

(NOV22) Part No. xxxx Copyright 2022 DCE042 Puce Tool ConnectMC Homologation du matriel sans fil et informations scurit Cet appareil est conforme la norme CAN ICES-3(B)/NMB-3(B) ou CAN ICES-5(B)/NMB-5(B). Cet appareil est conforme au paragraphe 15 du rglement du FCC et la (aux) norme(s) RSS exempt(s) de licence dIndustrie Canada. Son utilisation est sujette aux deux conditions suivantes

: 1) Ce dispositif ne doit pas causer dinterfrences nuisibles; et 2) Ce dispositif doit accepter toute interfrence reue, y compris toute interfrence pouvant causer un fonctionnementindsirable. Cet quipement a t test et jug conforme aux limites propres aux appareils numriques de Classe B, conformment au Paragraphe 15 du rglement du FCC. Ces limites sont destines offrir une protection raisonnable contre les interfrences nuisibles dune installation rsidentielle. Cet quipement produit, utilise et peut maner des ondes radiofrquences qui, sil nest pas install et utilis conformment aux directives, pourront causer des interfrences nuisibles aux communications radio. Cependant, en fonction des installations ralises, labsence dinterfrences nest pas garantie. Si cet quipement cause des interfrences nuisibles la rception radio ou tlvision (ce qui peut tre dtermin par la mise sous/hors tension de cet quipement) lutilisateur est encourag tenter de corriger ces interfrences en prenant lune ou plusieurs des mesures suivantes:

1)Rorienter lantenne de rception ou en changer lemplacement, 2)Augmenter la distance entre lquipement et le rcepteur, 3)Brancher lquipement une prise situe sur un circuit diffrent de celui sur lequel le rcepteur est connect, ou 4) Contacter un revendeur ou consulter un technicien radio/tlqualifi. Tout changement ou toute modification lappareil qui ne serait pas expressment approuv par le fabricant pourra annuler les droits de lutilisateur employer cet quipement. Conformment aux rglementions dIndustrie Canada, cet metteur radio ne peut fonctionner quavec une antenne dont le type et le gain maximal (ou dune valeur moindre) sont homologus par Industrie Canada pour cet metteur. Pour rduire toute interfrence radio potentielle pouvant affecter les autres utilisateurs, le type dantenne et ses gains devraient tre choisis de faon ce que la puissance isotrope rayonne quivalente ne soit pas suprieure aux limites permettant lacommunication. Afin de se conformer aux limites dexposition aux RF de FCC et Industrie Canada pour la population gnrale/lexposition non contrle, une ou plusieurs antennes utilises pour cet metteur doivent tre installes afin doffrir une distance de sparation dau moins 20 cm de toutes les personnes et doivent ne pas tre situes au mme endroit ou utilises conjointement tout autre antenne ou metteur. Afin de se conformer aux limites d'exposition aux RF de FCC et Industrie Canada pour la population gnrale/lexposition non contrle, une ou plusieurs antennes utilises pour cet metteur doivent tre installes afin doffrir une distance de sparation dau moins 5 mm aux tats-Unis et 10 mm au Canada de toutes les personnes et doivent ne pas tre situes au mme endroit ou utilises conjointement tout autre antenne ou metteur. Pour les produits BluetoothMD Avant de voyager en avion, sassurer de suivre les restrictions des compagnies ariennes quant lutilisation dappareils lectroniques et BluetoothMDpersonnels. La fonctionnalit dalarme hors plage a t conue pour servir aider alerter en cas de perte ou vol de produits. Ce nest pas un systme de scurit. La plage de connectivit peut aller jusqu 30.5 meters (100 pieds) en fonction de lenvironnement et des lieux. Les signaux de radiofrquences ondes courtes dun appareil BluetoothMD pourront affecter les oprations dautres appareils lectroniques ou mdicaux (comme les stimulateurs cardiaques ou les appareils acoustiques). REMARQUE: le terme et les logos BluetoothMD sont des marques dposes appartenant BluetoothMD, SIG, Inc. et toute utilisation de ces marques est autorise par licence. Toute autre marque de commerce et appellation commerciale reste la proprit de leurs propritairesrespectifs. Ce produit est conforme ces standards lorsquil est utilis avec un cordon de 1m 80 (6pi) oumoins. DCE042 Chip Tool Connect Certificaciones inalmbricas e informacin de seguridad Este dispositivo cumple con CAN ICES-3(B)/NMB-3(B)o con CAN ICES-5(B)/NMB-5(B). Este dispositivo cumple con la Seccin 15 de las normas de la Comisin Federal de Comunicaciones (FCC) y las normas RSS de exencin de licencia del Ministerio de Industria de Canad. Su funcionamiento est sujeto a las dos siguientes condiciones:

1) Este dispositivo no puede causar interferencia daina, y 2) Este dispositivo debe aceptar cualquier interferencia que reciba, incluyendo aquella interferencia que podra producir un funcionamiento no deseado. Este equipo ha sido probado y se ha demostrado que cumple con los lmites establecidos para dispositivos digitales de ClaseB, de conformidad con la Seccin 15 de las Normas de la FCC. Estos lmites estn diseados para ofrecer un nivel razonable de proteccin contra la interferencia daina en instalaciones residenciales. Este equipo genera, utiliza y puede emitir energa de radiofrecuencia y, si no se instala y utiliza de acuerdo con las instrucciones proporcionadas, puede producir una interferencia daina a la comunicacin radial. Sin embargo, no existen garantas de que no ocurra interferencia alguna en una instalacin en particular. Si este equipo produce interferencia daina a la recepcin radial o de televisin, lo que puede determinarse al apagar y volver a encender el equipo, se pide al usuario que corrija la interferencia implementando una o ms de las siguientesmedidas: 1) Cambie la orientacin o el lugar donde est ubicada la antena receptora, 2) Aumente el espacio que separa al equipo del receptor, 3) Conecte el equipo a una toma de corriente que est en un circuito diferente al circuito al que est conectado el receptor, o 4) Consulte con el distribuidor o con un tcnico de radio y televisin con experiencia que pueda ayudarle. Los cambios o modificaciones que no estn aprobados expresamente por el fabricante podran anular la autorizacin del usuario para utilizar el dispositivo. Segn el reglamento del Ministerio de Industria de Canad, este transmisor de radio puede funcionar solamente con una antena del tipo y de la mxima (o menor) ganancia aprobados para el transmisor por el Ministerio de Industria de Canad. Para reducir la posible interferencia radioelctrica a otros usuarios, el tipo de antena y su ganancia deberan elegirse de manera que la potencia isotrpica radiada equivalente (p.i.r.e.) no sea mayor que la necesaria para una comunicacinsatisfactoria. Para cumplir con los lmites de exposicin a radiofrecuencia de FCC e Industry Canada para la poblacin general/exposicin no controlada, la(s) antena(s) utilizada(s) para este transmisor debe(n) instalarse para proporcionar una distancia de separacin de por lo menos 20 cm de todas las personas y no debe ubicarse ni utilizarse junto con cualquier otra antena o transmisor. Para cumplir con los lmites de exposicin a radiofrecuencia de FCC e Industry Canada para la poblacin general/exposicin no controlada, la(s) antena(s) utilizada(s) para este transmisor debe(n) instalarse para proporcionar una distancia de separacin de por lo menos 5mm en los Estados Unidos y 20cm en Canad de todas las personas y no debe ubicarse ni utilizarse junto con cualquier otra antena o transmisor. Para productos con Bluetooth Al viajar en avin, asegrese de cumplir con las restricciones de las lneas areas acerca del uso de dispositivos electrnicos personales y Bluetooth. La funcin de alerta de fuera de alcance ha sido diseada para servir de ayuda para evitar la prdida o robo de productos. No es un sistema de seguridad. El rango de conectividad es de hasta 30.5 m (100 pies) dependiendo del entorno y la ubicacin. Las seales de radiofrecuencia de onda corta de un dispositivo Bluetooth pueden afectar el funcionamiento de otros dispositivos mdicos y electrnicos (como marcapasos o audfonos). NOTA: La marca denominativa y los logotipos de Bluetooth son marcas registradas propiedad de Bluetooth, SIG, Inc. y todo uso de dichas marcas se hace bajo licencia. Otras marca y nombres comerciales son de sus respectivospropietarios. Este producto cumple con estas normas cuando se pone en funcionamiento con un alargador de 1.82 m (6 pies) o mscorto.

Instruction Manual Guide Dutilisation Manual de instrucciones DCR008 Rechargeable Mini Bluetooth Speaker If you have questions or comments, contact us. Pour toute question ou tout commentaire, nous contacter. Si tiene dudas o comentarios, contctenos. 1-800-4-DeWALT English (original instructions) Franais (traduction de la notice dinstructions originale) Espaol (traducido de las instrucciones originales) 3 17 31 Fig. A DCR008 6 3 4 1 1 Power button 2 Volume up button 3 Volume down button 4 Bluetooth** status indicator LED 5 Play/Pause button 6 Bluetooth** button 7 Carry strap 8 Charging cable 9 Charger plug 10 Charging plug 11 Charging port cover 12 Charge indicator LED Fig.B 7 8 11 2 10 12 5 9 Composants Componentes 13 10 11 1 English (original instructions) English

 WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or seriousinjury. WARNING: To reduce the risk of injury, read the instructionmanual. Intended Use This DeWALT Bluetooth speaker is designed to play/stream audio via a wireless Bluetooth connection to a mobile phone or other audio device. DO nOT use under wet conditions or in presence of flammable liquids orgases. DO nOT let children come into contact with the unit. Supervision is required when inexperienced operators use thisunit. Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or propertydamage. which, if not avoided, could result in death or seriousinjury. situation which, if not avoided, will result in death or seriousinjury.

 DANGER: Indicates an imminently hazardous

 WARNING: Indicates a potentially hazardous situation

 CAUTION: Indicates a potentially hazardous situation

 (Used without word) Indicates a safety relatedmessage. which, if not avoided, may result in minor or moderateinjury. NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage. IMPORTANT SAFETY INSTRUCTIONS

 WARNING:

a ) Read theseinstructions. b ) Keep theseinstructions. c ) Heed allwarnings. d ) Follow allinstructions. e ) Do not use this apparatus nearwater. f ) Clean only with a drycloth. g ) Do not block any ventilation openings. Use in accordance with the manufacturersinstructions. h ) Do not use near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produceheat. i ) Protect the charging cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from theapparatus. j ) Only use attachments/accessories specified by themanufacturer. 2 k ) Unplug this apparatus during lightning storms or when unused for long periods oftime. l ) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as charing cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has beendropped. m ) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on theapparatus. n ) Do not use under wet conditions or in presence of flammable liquids orgases. o ) Do not keep ears close to thisappliance. Safety Instructions for Speakers To reduce the risk of fire or electric shock, do not expose this apparatus to rain ormoisture. Do not abuse charging cord. Never carry the speaker by its charging cord. Never pull the charging cord to disconnect from the charging port. Keep the charging cord away from heat, oil and sharpedges. Switch off before leaving speaker unattended, when speaker is not in use, before changing accessories or attachments, and before servicing. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for theirsafety. Children should be supervised to ensure that they do not play with theappliance. No exposed flame sources, such as lighted candles, should be placed on or near thespeaker. To reduce the risk of hearing damage, do not place ears too close to thespeaker. SAVE THESE INSTRUCTIONS FOR FUTURE USE Additional Safety Information

 WARNING: Never modify the speaker or any part of it. Damage or personal injury couldresult. The label on your speaker may include the following symbols. The symbols and their definitions are asfollows:

V ......................... volts Hz ....................... hertz min ..................... minutes RPM .................... revolutions per OPM .................... oscillations per minute or DC ...... direct current

...................... Class I Construction

(grounded)

/min .............. per minute BPM .................... beats per minute IPM ..................... impacts per minute minute sfpm ................... surface feet per minute SPM .................... strokes per minute A ......................... amperes W ........................ watts Wh ...................... watt hours Ah ....................... amp hours or AC ........... alternating current or AC/DC .... alternating or direct current

...................... Class II Construction

(double insulated) no ....................... no load speed n ......................... rated speed PSI....................... pounds per square inch

...................... earthing terminal

..................... safety alert symbol

..................... visible radiation do not stare into the light

..................... wear respiratory protection

..................... wear eye protection

..................... wear hearing protection

..................... read all documentation

..................... do not expose to rain BATTERIES The product is not fully charged out of the carton. Before using the product, read the safety instructions below and then follow the charging proceduresoutlined. nOTE: If the product is unused for approximately 90days, fully charge the battery to help prolong the life of thebattery. Important Safety Instructions for All Integral Battery Charging and cautionary markings for the battery, charging cable and product. Failure to follow the warnings and instructions may result in electric shock, fire and/or seriousinjury.

 WARNING: Read all safety warnings, instructions,

 WARNING: Only charge product using a certified power adapter that is compliant with applicable country regulations and international/regional safety standards. Using adapters that do not meet applicable safety standards could result in injury. Only use the charging cable supplied by the manufacturer for charging. The provided charging cable is not intended for any uses other than charging DeWALT rechargeable tools with charging ports. Charging other types of tools may cause their batteries to overheat and burst, resulting in personal injury, property damage, fire, electric shock orelectrocution. DO NOT expose charging cable to water, rain orsnow. Pull by the plugs rather than the cord when disconnecting the charging cable. This will reduce the risk of damage to the plugs andcord. Make sure that the cord is located so that it will not be stepped on, tripped over or otherwise subjected to damage orstress. DO NOT use a charging cable with a damaged cord orplugs. Have them replacedimmediately. Foreign materials of a conductive nature, such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil or any buildup of metallic particles should be kept away from the charging plugs and port. Always unplug the charging cable from the power supply when there is no tool attached toit. English Charging Procedure (Fig.A, B) 1. Pull the charging port cover(11) away from thespeaker. 2. Insert the charging plug(10) into the charging port(13). 3. Plug the charger plug(9) into any charging port (such as on a computer or wall adapter). nOTE: Charging takes two hours depending on power supply rating (5V, 1A). 4. The charge indicator LED(12) color is red and continuously on whilecharging. 5. Charging is complete when the charge indicatorLED(12) color is green and continuously on. The battery can be left charging or the USB cable can bedisconnnected. Hot/Cold Delay When the speaker detects that the battery is too hot or too cold, it automatically starts a hot/cold delay, suspending charging until the battery has reached an appropriate temperature. The speaker then automatically switches to charging mode. This feature ensures maximum batterylife. 1. A cold battery may charge at a slower rate than a warmbattery. 2. During a hot/cold delay the charge indicator LED(12) will not illuminate. Charging will not activate until the battery temperature reaches between 40Fand104F (4C and 40C). 3. Once the battery has reached an appropriate temperature, the charge indicator LED(12) will continuously blink, indicating that the speaker has resumed the charging procedure. Important Charging Notes 1. The speaker may become warm to the touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the speaker after use, avoid placing the speaker in a warm environment such as in a metal shed or an uninsulatedtrailer. 2. If the speaker does not charge properly, take the speaker and USB cable to your local servicecenter. 3. You may charge a partially used battery whenever you desire with no adverse effect on thespeaker. Over Temperature Protection (Fig.A) When over temperature protection is activated, the charge indicator LED(12) will turn off. nOTE: The unit can still be used during over the temperature protection cycle. Checking State of Charge (Fig. A) When the speaker is powered ON, press the power button(1) and the speaker will tell you the percentage of charge remaining in the battery. nOTE: It does not indicate tool functionality and is subject to variation based on product components, temperature and end-userapplication. 3 English Charge Indicator LED Status 6. Select DeWALT DCR008 on your device and lEVEl OF ChARgE 50%

25% - 50%

25%

0% - 99%

100%

0% - 99%

100%

ChARgE inDiCATOR lEDCOlOR Green Yellow Red and blinking. If 3% or less of charge remains, the speaker will tell you "Battery low, please recharge."

Red No illumination Red Green DURing UsE DURing ChARging ChARging WhilE in UsE OPERATION Button Functions (Fig. A) Power Button Press and hold the power button1 to turn the speaker on oroff. When the speaker is on, press the power button(1) and the speaker will tell you the percentage of charge remaining in the battery Play/Pause Button When audio device connected via Bluetooth: Press the play/pause button 5 to begin playing a selection from the audio device. Press the play/pause button 5 again to pauseplay. To advance to the next track, press the play/pause button (5) twice quickly. To skip to previous track, press the play/pause button (5) three times quickly. Volume Adjustment Buttons The volume buttons2, 3 can be used to increase or decrease volume on thespeaker. The volume will increase or decrease one level with a quick press of either volume buttons(2), ( 3 ). The volume will increase continuously with a long press of either volume buttons(2), ( 3 ). Playing Audio Audio can be played through the speaker via a wireless Bluetooth connection to a compatible Bluetooth audio device. Pairing Speaker with a Bluetooth AudioDevice (Fig. A) 1. Place the speaker and the Bluetooth audio device within 3 ft. (1m) of eachother. 2. Turn on the speaker by pressing the power button(1). 3. Be sure the Bluetooth audio device has Bluetooth turned on. (Please consult your device's instruction manual for specific pairing instructions.) 4. Press the Bluetooth button(6) on the speaker. 5. The blue Bluetooth status indicator(4) will flash twice indicating the speaker is in pair mode. 4 confirmpairing. 7. Once pairing is successful, the Bluetooth status indicator(4) will remain illuminated blue. 8. The speaker will now play audio from yourdevice. nOTE: Audio output power:1x5W. Bluetooth status indicator Blink Patterns status/Mode Flashes twice Solid light No light Speaker is in pairing mode and discoverable by yourdevice. Speaker is connected with adevice. Speaker has timed out and/or isoff. Connecting a Previously Paired Bluetooth AudioDevice If a Bluetooth device has been previously paired to the speaker, it should automatically reconnect when the speaker is powered on. nOTE: The Bluetooth audio device must have Bluetooth turned on to automaticallypair. 1. If connection does not occur and you are unable to stream audio, please follow the instructions for Pairing Speaker with a Bluetooth AudioDevice. stereo Pairing with Two speakers 1. On both speakers, simultaneously press and hold the Bluetooth button(6) or three seconds. 2. Speakers will announce left channel and right channel to indicate that pairing was successful. 3. The Bluetooth status indicator(4) will be blue on the left channel speaker and the Bluetooth status indicator(4) will not be illuminated on right channel speaker. Timeout Functionality (Fig. A) To conserve battery life, the speaker is designed to power off automatically after fifteen minutes of inactivity. This inactivity could be due to the device being unpaired for fifteen minutes or the Bluetooth connection being broken for the same period of time. If the speaker powers off due to inactivity of any kind, refer to Connecting a Previously Paired Bluetooth AudioDevice. Bluetooth Range Optimum Bluetooth streaming range is roughly 30 ft. (9m) with a straight line of sight to the speaker, but distances up to 100 ft. (30m) are possible. Physical obstacles, other wireless devices or electromagnetic devices may affect the connectionquality. If Bluetooth connection is lost due to exceeding time of separation, exceeding the optimum distance, obstacles or otherwise, reconnecting your device with the speaker may benecessary. incoming Call If your phone receives a call while it is connected to the speaker, it will pause the Bluetoothconnection. When the call is disconnected, the speaker will automatically switch back to the Bluetoothconnection. MAINTENANCE Your DeWALT power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regularcleaning. Register Online Thank you for your purchase. Register your product nowfor:

WARRAnTY sERViCE: Registering your product will help you obtain more efficient warranty service in case there is a problem with yourproduct. English Cleaning

 WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use a dry cloth only. Never let any liquid get inside the tool; never immerse any part of the tool into aliquid. Accessories

 WARNING: Since accessories, other than those offered by DeWALT, have not been tested with this product, use of such accessories with this product could be hazardous. To reduce the risk of injury, only DeWALT recommended accessories should be used with thisproduct. Recommended accessories for use with your product are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DeWALT. Call 18004DeWALT

(18004339258) or visit our website: www.dewalt.com Repairs The speaker and charging cable are not serviceable. There are no serviceable parts inside the speaker.

 WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by a DeWALT factory service center or a DeWALT-authorized service center. Always use identical replacementparts. COnFiRMATiOn OF OWnERshiP: In case of an insurance loss, such as fire, flood or theft, your registration of ownership will serve as your proof ofpurchase. FOR YOUR sAFETY: Registering your product will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer SafetyAct. Register online at www.dewalt.com.. Three Year Limited Warranty For warranty terms, go to https://www.dewalt.com/

support/warranty. To request a written copy of the warranty terms, contact:

Customer Service at DeWALT Industrial Tool Co., 701East Joppa Road, Towson, MD 21286or call 1-800-4-DeWALT

(18004339258). lATin AMERiCA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained in the packaging, call the local company or see website for warrantyinformation. FREE WARning lABEl REPlACEMEnT: If your warning labels become illegible or are missing, call 1-800-4-DeWALT

(18004339258) for a freereplacement. 5 DeWALT Industrial Tool Co. 701East Joppa Road, Towson, MD 21286 Copyright 2022 The following are trademarks for one or more DeWALT power tools: the yellow and black color scheme, the D shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of thetool. NXXXXXX 10/22

Authority to Act as Agent Date: January 26, 2023 American Certification Body, Inc. 313 Park Avenue, Suite 300 Falls Church, VA 22046 To Whom It May Concern:

Kimberly Colbert. is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: 08/01/2023 By:

Title:

(Signature1) Senior Compliance Engineer On behalf of: Stanley, Black & Decker, Inc. 410-716-3563 Telephone:

Kirwan Magdamo

(Print name) 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. Stanley Black & Decker, Inc. 701 E. Joppa Road Towson, MD 21286 U.S.A.

THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD Date: January 26, 2023 Request for Confidentiality Subject: Confidentiality Request for: FCC ID: YJ7DCR008 and IC ID: 9082A-DCR008 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent *1 Permanent Permanent Permanent Permanent Permanent *3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual

(Stanley Black & Decker Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180)2___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:

Lead Project Engineer

(Signature/Title3) Kirwan Magdamo

(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent 030122-15 THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD letter has been provided. Letters should be placed on appropriate letterhead. 030122-15

Kirwan Magdamo Lead Project Engineer 701 East Joppa Road, Towson, MD 21286 T (410) 716 3563 Certification Application Attestation Statements Date: February 14, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:

Statement for 47 CFR section 2.911(d)(5)(i) _Stanley Black & Decker, Inc.______ certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: <N/A>

Statement for 47 CFR section 2.911(d)(5)(ii) _Stanley Black & Decker, Inc.______ (the applicant) certifies that, as of the date of the filing of this application, the applicant is not identified on the Covered List as an entity producing covered equipment. Thank you, By:

(Signature) Kirwan Magdamo

(Print name) Title:

Lead Project Engineer Company:

Stanley Black & Decker, Inc. Telephone: 410-716-3563 1 - The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist .

Kirwan Magdamo Lead Project Engineer 701 East Joppa Road, Towson, MD 21286 T (410) 716 3563 U.S. Agent Designation for Service of Process

(Applicant is Both Grantee and U.S. Agent) TO:

American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification Section 2.911(d)(7) Information This letter is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information changes. Applicant Company name: Stanley Black & Decker, Inc. Grantee Code: YJ7 Contact Name: Kirwan Magdamo Street Address: 701 East Joppa Road City/Province/Zip: Towson, MD 21286 Telephone No: +410-716-3563 Email: kirwan.magdamo@sbdinc.com Applicant Signature:

Date: February 14, 2023 Signed by (Printed Name/Title): Kirwan Magdamo/Lead Project Engineer