FCC ID: YJ7DCE041 DeWalt Bluetooth Tag

English DCE041 BLUETOOTH DeWALT TAG Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage.

 DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.

 WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.

 CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.

 (Used without word) Indicates a safety related message.

 WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage. in electric shock, fire and/or seriousinjury. WARNING: To reduce the risk of injury, read the instructionmanual. If you have any questions or comments about this or any DeWALT tool, call us toll free at: 1-800-4-DeWALT (1-800-

433-9258). GENERAL SAFETY WARNINGS

 WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or seriousinjury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE 1. This device contains a factory-installed coin cell battery. It cannot be removed or replaced. 2. Chemical burn hazard. Keep out of reach of children. 3. Do not use in extreme hot or cold conditions. Keep between -30 F (-34 C) and 140 F (60 C). 4. Choking hazard. Keep out of reach of children. 5. This device contains a lithium button/coin cell battery. Do not force open the device as the battery can cause severe internal burns and lead to death in as little as 2 hours if swallowed or enters the body. If the device is damaged in any way, stop using the device and keep it away from children. If you think batteries may have been swallowed or entered the body, seek immediate medical attention. 6. If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of an organic solvent and lithium salts. 7. Do not incinerate or dismantle this device. 8. Under abusive conditions, liquid may be ejected from the device. Avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 9. DO NOT dispose of device together with household waste material! Appliance that has reached the end of its life must be collected separately and returned to an environmentally compatible recycling facility. The label on your tool may include the following symbols. The symbols and their definitions are asfollows:

V ......................... volts Hz .......................hertz min .....................minutes or AC ...........alternating current or AC/DC .... alternating or direct current

...................... Class II Construction (double insulated) or DC ......direct current

...................... Class I Construction (grounded) no .......................no load speed n .........................rated speed

/min ..............per minute BPM ....................beats per minute IPM .....................impacts per minute RPM .................... revolutions per minute sfpm ................... surface feet per minute SPM ....................strokes per minute A .........................amperes W ........................watts Storage Recommendations The best storage place is one that is cool and dry, away from direct sunlight and excess heat or cold. Wireless Certifications and Safety Information When traveling on airlines, be sure to comply with the airline restrictions on usage of personal electronic devices and

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory protection

.....................wear eye protection

..................... wear hearing protection

..................... read all documentation Bluetooth. The out of range alert feature has been designed to act as an aid to warn against products getting misplaced or stolen. It is not a security system. The connectivity range is up to 100 feet (30.5 meters) depending on environment and location. The shortwave radio frequency signals of a Bluetooth device may impair the operation of other electronic and medical devices

(such as pacemakers or hearing aids). This device is CAN ICES-3(B)/NMB-3(B) compliant. This device complies with Part 15 of the FCC rules and Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesiredoperation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and adaptor. Connect the equipment into an outlet on a circuit different from that to which the adaptor is connected. Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated (e.i.r.p.) is not more than that necessary for successful communication. To comply with FCC and Industry Canada RF radiation exposure limits for general population, the antenna used for this device must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications to this equipment not expressly approved by the manufacturer could void the users authority to operate the device. NOTE: The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth, SIG, Inc. and any use of such marks by DeWALT is under license. Other trademarks and trade names are those of their respective owners. INTENDED USE This Bluetooth DeWALT Tag is designed for tracking and locating professional power tools, equipment, and machines using the DeWALT Tool Connect app. Do not use DeWALT Tag to track or locate people or animals. DO NOT let children come into contact with it. Fig. A 2 1 2 DeWALT Tool Connect This DeWALT Tag is capable of connecting with mobile devices that support Bluetooth Smart (or Bluetooth 4.0) technology.

(To see if your mobile device is compatible, visit: http://www.bluetooth.com/Pages/Bluetooth-Smart-Devices-List.aspx) DeWALT Tool Connect is an application for your smart device (such as a smart phone or tablet) that can connect and control your DeWALT Tag. NOTE: The Tool Connect App is governed by separate terms and conditions available for viewing through the mobile application. Pairing and Activating the DeWALT Tag (Fig. A) Step 1: Download the DeWALT Tool Connect applicationat:

Step 2: Follow the instructions in the app to create your Tool Connect account. Step 3: Connect your DeWALT Tag with the DeWALT Tool Connect app first by pressing the button (1) on the front of the tag until it begins to blink. Then go to the Home screen of the app and select "+ Tool." The tag can only be connected to one Tool Connect account at a time. Step 4: Once the connection is established, you will be prompted to give the product an individual name as well as confirm that you would like to register the product on your DeWALT.com account. For more information on DeWALT Tool Connect functionality and features, please call 18004-DeWALT (18004339258), visit www.DeWALT.com or view the FAQ page and help screens located inside the mobile application. Installing the DeWALT Tag

 WARNING: Do not apply tag to product where it will become wet or exposed to flammable liquids or gases.

 WARNING: Do not secure in such a way as to impede the safe use of the product to which the tag is attached.

 WARNING: Before using screws or rivets to install, ensure the space behind the placement is clear.

 WARNING: Do not pierce tag with screw, nail, drill bit, etc.

#6 Pan head self-tapping screw through one or both of the mounting holes ( 2 ). The DeWALT tag is designed to track tools and equipment using the Tool Connect app. It will not prevent theft from happening. The tag can be installed in a variety of orientations. Consider installing the tag to prevent tampering. The tag can be installed using the following attachment options:

Glue or epoxy to back of tag. Be sure glue or epoxy is compatible with mounting surface. Adhesive backing. Cable or zip tie through one or both of the mounting holes ( 2 ). 5/32 diameter rivet through one or both of the mounting holes ( 2 ). Technical Data DCE041 3 3 Years

<100'

YJ7-DCE041 9082A-DCE041 IP67

??

VDC kg Voltage Battery life Signal Range FCC ID IC Ingress Protection Weight MAINTENANCE Cleaning  WARNING: Never use solvents or other harsh chemicals for cleaning the tag. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tag;

never immerse into aliquid. Repairs The tag is notserviceable, though its button cell battery can be replaced at a DeWALT authorized service center.

 WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement, when applicable) should be performed by a DeWALT factory service center or a DeWALT authorized service center. Always use identical replacementparts. Register Online Thank you for your purchase. Register your product nowfor:

WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty service in case there is a problem with yourproduct. CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft, your registration of ownership will serve as your proof ofpurchase. FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer SafetyAct. Register online at www.dewalt.com/register. Three Year Limited Warranty DeWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DeWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so these limitations may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. In addition to the warranty, DeWALT tools are covered byour:

1 YEAR FREE SERVICE DeWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year afterpurchase. 90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your DeWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund no questionsasked. LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained in the packaging, call the local company or see website for warrantyinformation. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DeWALT (1-800-

433-9258) for a freereplacement. The following are trademarks for one or more DeWALT power tools: the yellow and black color scheme, the D shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool. DeWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286

(FEB17) Part No. xxxxxx DCE041 Copyright 2017 DeWALT

FCCID#

IC#

INTERNAL PHOTOS YJ7DCE041 9082ADCE041 Page1of2 FCCID#

IC#

INTERNAL PHOTOS YJ7DCE041 9082ADCE041 Page2of2

FCCID#

IC#

EXTERNAL PHOTOS YJ7DCE041 9082ADCE041 Page1of2 FCCID#

IC#

EXTERNAL PHOTOS YJ7DCE041 9082ADCE041 Page2of2

REV. X-2 X-3 X-4 A A1 B C BY REVISIONS Sonic Weld Version -Initial DESCRIPTION Quote Updated to fit PCBA ESL Release APPROVED DATE 9/1/2016 9/1/2016 9/1/2016 9/14/2016 DVT Release, added P/N, Tollerance adjusted 10/11/2016 MSL Release C Added Circular Rib Details, Update Graphic 1/4/2017 3/1/2017 MODEL: DCE041 FCC ID: YJ7DCE041 IC: 9082A-DCE041 YYYY WW-C1 Laser Marked Label NOTES:

1. 2. 3. FOR DIMENSIONS AND DETAILS NOT SHOWN REFER TO 3D CAD DATA Material - Cycoloy C2950 ES283 Color: Yellow (Code ES283) THIRD ANGLE PROJECTION UNLESS OTHERWISE NOTED, THIS DOCUMENT CONTAINS LAIRD TECHNOLOGIES INFORMATION. REPRODUCTION, USE, DISCLOSURE OR TRANSMITTAL OF ALL OR ANY PART OF THIS DOCUMENT IS PROHIBITED EXCEPT TO THE EXTENT APPROVED IN WRITING BY AN AUTHORIZED REPRESENTATIVE OF LAIRD TECHNOLOGIES. LAIRD TECHNOLOGIES RESERVES ALL RIGHTS UNDER PATENTS, TRADEMARKS, COPY RIGHTS AND TRADE SECRETS. COPYRIGHT, LAIRD TECHNOLOGIES 2016, ALL RIGHTS RESERVED. 5 4 CAD FILE: Back Cover UNLESS OTHERWISE SPECIFIED:

DIMENSIONS ARE IN MILLIMETERS TOLERANCES:

ANGULAR:

X.X X.XX

.5

.2

.1 INTERPRET GEOMETRIC TOLERANCING PER: ASME 14.5M MATERIAL:

PC-ABS Cycoloy C2950 MASS:

- -

3 DATE DRAWN BY CHECKED BY CHECKED DATE CLIENT: SBD PROJECT: 1644 8/12/2016 LSR GW

- -

SHEET 1 OF 1 SCALE: 2:1 BACK COVER DWG. NO. TITLE:

SIZE A 2 1 REV C

Kirwan Magdamo Sr. Project Engineer 701 East Joppa Road, Towson, MD 21286 T (410) 716 3563 F (410) 716 2961 Authority to Act as Agent Date: March 2, 2017 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

Thomas T. Smith, Ryan Urness and Amanda Hauck of LS Research, LLC are authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. The term of this Agency Agreement shall start on the above date of this Agreement and shall continue in force until one (1) year thereafter. Thank you, Kirwan Magdamo

(Print name) __________________________

(Signature) Sr. Project Engineer By:

Title:

On behalf of: Stanley Black & Decker Telephone:

410-716-3563

(Company Name)

Kirwan Magdamo Sr. Project Engineer 701 East Joppa Road, Towson, MD 21286 T (410) 716 3563 F (410) 716 2961 Request for Confidentiality Date: March 2, 2017 Confidentiality Request for:

FCC ID: YJ7DCE041 To Whom It May Concern, Pursuant to FCC 47 CRF 0.457(d) and 0.459, the applicant requests that a part of the subject FCC application be held confidential. The applicant requests the exhibits listed below be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Block Diagram Schematics Operation Description/Theory of Operation Applicant has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Sincerely,

(Signature) Name: Kirwan Magdamo Title: Sr. Project Engineer Phone: 410-716-3563 Email: Kirwan.Magdamo@sbdinc.com

RE: Stanley Black & Decker FCC ID: YJ7DCE041 IC: 9082A-DCE041 ATCB020765 ACB:

FYI - The confidentiality letter requests Operational Description to be held confidential, however the test report exhibit contains the information from the Operational Description exhibit. Please note while the Op Description can be held confidential, the test report may not. Please confirm the applicant is aware this information will be public. Response: The applicant is aware and would like to move forward as is.