Getting Started With Your LTE PDA Model: N5004L Index N5004L overview N5004L overview Setting upyour device Safety information Certificate Warranty information& registration Customer support 3 4 6 10 12 13 Front/Back Rear camera Volume control Wake/Sleep button Rear camera flash Bottom Speaker Type-C connector 3 Settingupyourdevice Followthesestep-by-stepinstructionstosetup yourN5004L. Power off the device before inserting any cards!
2 1 Remove Back Cover Remove the back cover by prying the lower left corner of your device. 2 Insert SIM Orient SIM card to match diagram on slot. SIM (Nano) support 4G LTE connections. 3 Replace Back Cover After installing the SIM card, memory card, and battery, align the cover and snap it closed. Be sure to press all around the edges to ensure a secure fit. 4 Charge/Sync Plug in the type C connector to charge the device or transfer data. 3 1 4 Warning:
SIM cards are small enough to become a choking hazard, so pleasekeep them away from children & pets. SIMcards are also quite delicate. Please becareful when handling your card. 4 these environments may result in circuit malfunctions. Do not use your device during thunderstorms Safety information This section contains important information about the operation of your device, it also contains information about how to use the device safely. Read this information carefully before using your device. Electronic device Do not use your device if using the device is prohibited. Do not use the device if doing so causes danger or interference with other electronic devices. Interference with medical equipment Follow rules and regulations set forth by hospitals and health care facilities. Do not use your device where prohibited. Some wireless devices may affect the performance of hearing aids or pacemakers. Consult your service provider for more information. Pace maker manufacturers recommend that a minimum distance of 15 cm be maintained between a device and a pacemaker to prevent potential interference with the pacemaker. If using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the device in your front pocket. Areas with flammables and explosives Do not use the device where flammables or explosives are stored (in a gas station, oil depot,orchemicalplant,forexample).Using your device in the seen viron ments in creases the risk of explosion or fire. In addition, follow the instructions indicated in text or symbols. Do not store or transport the device in containers with flammable liquids, gases, or explosives. Traffic security Observe local laws and regulations while using the device. Toreduce the risk of accidents, do not use your wireless device while driving. Concentrate on driving. Your first responsibility is to drive safely. Do not hold the device while driving. Use hands-free accessories. RF signals may affect the electronic systems of motor vehicles. For more information, consult the vehicle manufacturer. Donot place the devic eover the air bagor inthe airbag deploymentarea in amotor vehicle. Doing so may hurt you because of the strong force when the air bag inflates. Wireless devices may in terfere with the airplanes flight system. Do not use your device where wireless devices arenot allowed according to the airplane companys regulations. Operating environment Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the device in 6 7 Do not connect battery poles with conductors, such as keys, jewelry, or other metal materials. Doing so may short-circuit the battery and cause injuries or burns. to protect your device against any danger caused by lightning. Ideal operating temperatures are 0 C to 35 C. Ideal storage temperatures are -
20 C to 45 C. Extreme heat or cold may damage your device or accessories. Do not expose your device todirect sunlight (such as on a car dashboard) for prolonged periods. Toprotect your device or accessories from fire or electrical shock hazards, avoid rain and moisture. Keep the device away from sources of heat and fire, such as a heater, microwave oven, stove, water heater, radiator, orcandle. Do not place sharp metal objects, such as pins, near the earpiece or speaker.The earpiece may attract these objects and result in injury. Stop using your device or applications for a while if the device is overheated. If skin is exposed to an overheated device for an extended period, low temperature burn symptoms, such as red spots and darker pigmentation, may occur. Do not use your devices camera flash directly in the eyes of people or pets. Otherwise temporary loss of vision or damage to the eyes may occur. Donot touch the devicesantenna.Otherwise, communication quality may be reduced. Do not allow children or pets to bite or suck the device or accessories. Doing so may result in damage orexplosion. Observelo callaws and regulations, and respect the privacy and legal rightsof others. Child safety Comply with all precautions with regardto childssafety.Letting children play with the device or its accessories may be dangerous. The device includes detachable parts that may present a choking hazard. Keep away from children. The device and its accessories are not intended for use by children. Children should only use the device with adult supervision. Accessories Using an unapproved or incompatible power adapter, charger or battery may cause fire, explosion or otherhazards. Choose only accessories approved for use with this model by the device manufacturer.The use of any other types of accessories may void the warranty, may violate local regulations and laws, and may be dangerous. If the power cable is damaged (for example, the cord is exposed or broken), or the plug loosens, stop using it at once. Continued use may lead to electric shocks, short circuits, or fire. Do not touch the power cord with wet hands or pull the power cord to disconnect the charger. Do not touch the device or the charger with wet hands. Doing so may lead to short circuits, malfunctions, or electricshocks. If your charger has been exposed to water, other liquids, or excessive moisture, only an authorized service center has the right to inspect. Battery safety 6 7 Keep the battery away from excessive heat and direct s unlight. Do not place it on or in heating devices, such as microwave ovens, stoves, or radiators. Batteries may explode if overheated. Do not attempt to modify or remanufacture the battery, insert foreign objects into it, or immerse or expose it to water or other liquids. Doing so may lead to fire, explosion, or other hazards. Environmental protection The device and its accessories (if included), such as the power adapter, headset, and battery should not be disposed of with household garbage. Disposal of the device and its accessories is subject to local regulations. Support If the battery leaks, ensure th at the electrolyte does not make direct contact with your proper collection and recycling. skins or eyes. If the electrolyte to uches your skins or splashes into your eyes, immediately flush with clean water and consult a doctor. In case of battery deformation, color change, or overheating while charging or storing, immediately stop using the device and remove the battery. Continued use may lead to battery leakage, fire, or explosion. Safety precautions Use of wireless hands-freesystem(headdevice,headset) with alowpower Bluetooth emitter. Make sure the device has a low SAR. Do not put batteries in fire as they may explode. Damaged batteries may also explode. This advice applies especially to children, adolescents and pregnant women. Dispose of used batteries in accordance with local regulations. Improper battery use may lead to fire, explosion, or other hazards. Use device when the signal quality is good. Do not allow children or pets to bite or suck the battery. Doing so may result in damage People having active medical implants should prefer bly keep the cell devic eat least or explosion. Do not smash or pierce the battery,or expose it to highexternal pressure.Doing so may lead to a short circuit or overheating. Do not drop the device or battery. If the device or battery is dropped, especially on a hard surface, it may be damaged. If the device standby time shortens significantly, replace the battery. Cleaning and maintenance Keep the device and acces sories dry.Do not attempt to dry it with an external heat source, such as a microwave oven or hair dryer. Donot expose your device or accessories to extreme heat or cold. These environments may interfere with proper function and may lead to fire or explosion. Avoid collision, which may lead to device malfunctions, overheating, fire, or explosion. Beforeyou clean or maintain the device, stop using it, stop all applications, and disconnect all cables connected to it. Do not use any chemical detergent, powder,or other chemical agents (such as alcohol and benzene) to clean the device oraccessories. These substances may cause damage to parts orpresen tafire hazard.Useaclean,soft,and dry cloth to clean the device and accessories. Donot place magneticstrip ecards,such as creditcards and device cards,nearthedevicefor extended periods of time. Otherwise the magneticstripe cards may be damaged. Do not dismantle or remanufacture the device and its accessories. This voids the warranty and releases the manufacturer from liability for damage. In case of damage, contact an authorized service center for assistance or repair. If the device screen is broken in a collision, immediately stop using the device. Do not touch or attempttore move the brokenparts. Promptly contact anauthorized service center. 15cm away from theimplant. Disposal and recycling information This symbol on the device or on its packaging indicates that the device
(including its electrical accessories) should not be disposed of as normal household garbage. Do not dispose of your device as unsorted municipal waste.Thedeviceshould behanded over toan authorized collectioncenter for recycling or proper disposal at the end of its life. Battery caution 1. Use only NUU-approved batteries, chargers, and cables to charge your device. Unapproved chargers or cables can cause the battery to explode or damage the device. 2. Use only NUU-approved batteries, chargers and cables. Use unapproved batteries, chargers and cables may cause safety issue and the warranty will be lost. 3. You can recharge your battery many times, but all batteries have a limited lifespan. If you notice a significant deterioration in your devices battery life, you will need to purchase a replacement battery for replacement. If the battery is built-in in the device, do not attempt to remove built-in batteries and contact an authorized NUU service center for a replacement. 4. Your device may becomewarm after prolonged use or when exposed to high ambient temperatures. If your device becomes hot tothetouch, unplug the USB cable, disable non-essential features, and avoid prolonged skin contact. Place your device in a cool location and allow it to cool down to room temperature. 5. Charging times may vary depending on the ambient temperature and the remaining battery level. 6. Avoid using your device when it is charging. Do not cover your device or the charger when it is charging. 8 9 highest SAR value for this model device when tested for use worn on the body, as described in this user guide, is 1.06W/Kg (Body-worn measurements differ among device models, depending upon available accessories and FCC requirements). The maximum scaled SAR in hotspot mode is 1.25W/Kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: 2ADINN5004LR1 Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Asso-ciation (CTIA) web-
site at http://www.wow-com.com. * In the United States and Canada, the SAR limit for mobile devices used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a sub-stantial margin of safety to give additional protection for the public and to account for any variations in measurements. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved. FCC information FCC STATEMENT:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SAR Information Statement Yourwireless device isaradiotransmitter andreceiver. It isdesigned andmanufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are conducted with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a device model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations
(worn on the body) as required by the FCC for each model. The 10 11 IC statement CE Operation of 5150-5250 MHz is restricted to indoor use only. This device complies with Operation is subject to the following two conditions:
Industry Canadalicence-exempt RSSstandard(s)
(1 )This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value for this model device when tested for use worn on the body is 1.06W/Kg. The maximum scaled SAR in hotspot mode is 1.25W/Kg.This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. Le fonctionnement de 5150-5250 MHz est limit une utilisation en intrieur uniquement. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Ce dispositif est conforme aux normes autoriser-exemptes du Canada RSS dindustrie Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.Cet quipement est conforme avec lexposition aux radiations IC dfinies pour un environnement non contrl. Lutilisateur final doit respecter les instructions de fonctionnement spcifiques pour satisfaire la conformit aux expositions RF. Cet metteur ne doit pas tre co-localises ou oprant en conjonction avec une autre antenne ou transmetteur. Ces exigences dfinissent la valeur SAR limite 1.6 W / kg en moyenne par gramme de tissu. La valeur SAR la plus leve pour ce modle de dquipement test lorsque port sur le corps est 1.06W/Kg. lchelle maximale sar en mode hotspot est de 1.25W/Kg Cet appareil a t test pour des oprations ports sur le corps typiques. Pour se conformer aux exigences dexposition aux radio frquences, une distance minimale de 10 mm doit tre maintenue entre le corps de lutilisateur et le combin, y compris lantenne. Les pinces de ceinture, les tuis et autres accessoires similaires utiliss par cet appareil ne doivent pas contenir de composants mtalliques. Les accessoires portatifs qui ne rpondent pas ces exigences peuvent ne pas se conformer aux exigences dexposition RF et doit tre vite. Utilisez uniquement lantenne fournie ou une antenne approuve 12 13 Made in China Warranty information Customer support Please visit our website for details on warranty information. Questions? Let us help. Were here to support you. www.nuumobile.com Warranty registration US Phone:
Email:
Toll Free: 844-NUU-3365 U.S. hours: 9am-6pm ET, chat: M-F 24hrs support@nuumobile.com Register Your Device Thank you for choosing NUU. To receive helpful tips and faster tech support, register your device online at US:
us.nuumobile.com/register/
14 15 Learn more about NUU products, features and accessories at www.nuumobile.com