User manual Model:F2 Brand:NUU Follow these step-by-step instructions to set up your F2. Power o the phone and remove battery before inserting any cards!
Remove Back Cover Remove the back cover by prying the back cover up with your ngers. Insert SIM (Dual SIM Standby) Orient SIM card to match diagram on slot. SIM 1 (Mini) supports GSM connections. SIM 2 (Mini) supports GSM connections. Insert microSD Memory Card Insert the Battery Power off the phone and remove battery before inserting memory card. Slide the SD clip to unlock, tilt to open, insert card, close and slide to lock again. Align the battery contacts, then insert the battery contact-rst. Replace Back Cover After installing the SIM card, memory card, and battery, align the cover and press it closed. Make sure you press all around the edge to ensure a secure t. Charge/Sync Plug in the microUSB connector to charge the phone or transfer data. Warning: SIM cards are small enough to become a choking hazard, so please keep them away from children. SIM cards are also quite delicate. Please be careful when handling your card. THANK YOU!
For Your Purchase of the F2 ABC JKL TUV D EF MNO WXYZ G HI P Q R S ABC JKL TUV D EF MNO WXYZ G HI P Q R S Earpiece LCD Screen The Keypad Menu Contacts/Back Arrow Keys Menu/Action Answer Call End Call/Power On/O Hold 1 for Voicemail Call Holding # key swaps between GENERAL and SILENT mode microUSB connector Microphone AUX-In/Headset jack FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Specific Absorption Rate (SAR) information:
This Mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: Mobile phone (FCC ID: 2ADINNUUF2) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.730W/kg and when properly worn on the body is 0.656W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. IC Warning This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. RF Exposure Information and Statement The SAR limit of USA is 1.6 W/kg averaged over one gram of tissue. Device types: Mobile phone (IC: 20782-NUUF2) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.730W/kg and when properly worn on the body is 0.656W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body. To maintain compliance with IC RF exposure requirements, use accessories that maintain a 10mm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with IC RF exposure requirements, and should be avoided. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement RF exposition Information et Dclaration La limite SAR des Etats-Unis est de 1,6 W / kg en moyenne par gramme de tissu. Types d'appareil: Mobile phone (IC: 20782-NUUF2) a galement t test contre ces valeurs. La valeur SAR la plus leve dclare en vertu de cette norme lors de la certification de produit pour une utilisation l'oreille est 0.730W / kg et lorsqu'il est correctement port sur le corps est 0.656W / kg. Ce dispositif a t test pour les oprations typiques ports sur le corps avec le dos du combin gard 10mm du corps. Afin de maintenir la conformit aux exigences de la IC, utilisez des accessoires qui maintiennent une distance de sparation 10mm entre le corps de l'utilisateur et le dos du combin. L'utilisation de pinces de ceinture, tuis et accessoires similaires ne doivent pas contenir de composants mtalliques dans son ensemble. L'utilisation d'accessoires qui ne satisfont pas ces exigences ne peuvent pas se conformer aux exigences de la IC, et devrait tre vite. Port au corps Opration Ce dispositif a t test pour les oprations typiques ports sur le corps. Pour se conformer aux exigences d'exposition aux radiofrquences, une distance de sparation minimale de 10mm doit tre maintenue entre le corps de l'utilisateur et le combin, y compris l'antenne. Tiers pinces de ceinture, tuis et autres accessoires similaires utiliss par ce dispositif ne doit pas contenir de composants mtalliques. accessoires qui ne rpondent pas ces exigences peut ne pas se conformer aux exigences d'exposition RF et doit tre vit Body-port. Utilisez uniquement l'antenne fournie ou une approbation.