EyeW485-H Wireless Communication Module Quick Use Manual 1 Application Scenarios EyeW485-H is applied to the new energy industry, especially the photovoltaic industry. For use with smart communication box developed and manufactured by SUNGROW in residential/industrial/utility/floating photovoltaic plants. It receives the inverter data transmitted by the EyeW485 via WiSun and in turn transmits it to the SunCloud. 2 Nameplate Nameplate Wireless Communication Module Model EyeW485-H DC-Input 24V 0.1ATemperature -30 ... +60 Enclosure /SUNGROW POWER SUPPLY CO.,LTD S/N xxxxxxxxxx Made in China Description Parameter Description DC input DCinput Working ambient temperature Normal Operating temperature range Do not dispose of thecommunication module as household waste Please read the quick use manual 3 Description of the Indicator Status The EyeW485-Hneeds to be used with the EyeW485, both of which communicate wirelessly through WiSun to enable networking. The indicator status of EyeW485-H and EyeW485 is explained below. Description of the EyeW485-H indicator status Indicators Color Status Description Run indicator
(RUN) Green WiSun network status indicator Blue
(NET) Off Off External power supply disconnection Blinking Normal operation Connected with EyeW485 Steady on Fail to connect with EyeW485 Note: Blinking is defined as blinking on for 1s and off for 1s and then repeats. Description of the EyeW485 indicator status Indicators Color Status Description Run and malfunction Red/Yellow-Green Off External power supply disconnection Indicators Color Status Description indicator
(RUN)) yellow and Normal operation Blinking green Blinking red Steady on Off Blinking Failed to get the SN of the inverter, MAC address generation failed No networking, in the to network Connected to EyeW485-H No communication on the WiSun network The WiSun network is communicating WiSun network Off process of broadcasting status indicator Blue
(NET) Data indicator
(COM) communication Green Note: Blinking is defined as blinking on for 1s and off for 1s and then repeats. 4 Troubleshooting Follow these steps to perform troubleshooting if the EyeW485-H indicators are in the following status. No. Fault Check method 1 RUN indicator off If the power supply voltage is normal If necessary, open the cover and check whether the backplane supply voltage is DC5.0V with the multimeter;
and the run indicator is still off, the wireless communication module is defective.Please contact SUNGROW for post-sales service. No. Fault Check method 2 NET indicator off Check whether the EyeW485-His connected to external power;
Check whether the EyeW485-H is connected. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. To maintain compliance with FCCs RF Exposure guidelines, this equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.