FCC ID: WA2ST4310P Tracking Device

ST4310P User Manual Suntech International Ltd. 1. Introduction buyer. 2. Overview periodically. 2-1. Operation Mode ST4310P User Manual This document describes features, protocols and detail operation of ST4310P. If there is another operation description document for special buyer to customize or model and the contents of the document is different with this, customizing document should be applied for special Device consists of NETWORK, GPS and event parts. The main purpose of device reports getting GPS position and other informs of vehicle to server Device can control or check connected lines and support additional functions. The device has 3 operation modes, driving, parking and emergency.

** Driving

: Driving status when ignition is on.

** Parking

: Parking status that starts if ignition is off during more than T1.

** Emergency : Once panic button is On or any other status as per designed. The device sends emergency reports until A1 times or receiving server acknowledge. 2-2. Report AVL reports GPS and some information at predefined interval, depending on the current modes. Also, AVL sends some alerts, for example, movement at the parking condition, changing of connected input line and so on. command response. Device distinguishes all reports with 6 types, Status report, emergency, event, alert, alive and Device can store reports when reporting route (For example, NETWORK condition) is not successful. Storage capacity is up to 2,000 status reports, 50 emergency reports, 50 alert reports (include event reports) and 1500 bytes as command response. In case of status reports, oldest report is erased and new report is buffered when the buffer is full and new status report enters (FIFO). When reporting condition is recovered, device starts sending all buffered reports. Also, this capacity can increase if it is needed. Each type of reports has priority, and priority is as below. Emergency Command Response Alert Status Report Alive (Lowest) 2 Emergency is the first to be sent after recovering NETWORK condition. ST4310P User Manual Parameters of device can be changed by NETWORK or SMS, and some control can be realized also 2-3. Setting Parameter in the same way. Detail protocols are described in Chapter 4. 2-4. Features Key features are described here;

Device can process two steps of power-down, Sleep and Deep Sleep, for reducing power consumption when the vehicle is parked. LED indicates NETWORK and GPS states. Its helpful to check error cause. Device has 2 output lines, 3 input lines and ignition line.

- Update Firmware by Over The Air (FOTA) When Firmware of device has some error or has to be changed for a new service to be implemented, device can update internal ROM file by over the air (FOTA), remotely via NETWORK. Customers do not need to visit every vehicle to download the new firmware. Method of FOTA describes at SunTech_OTA_UA_Protocol document in detail. Device can check whether the vehicle moves off the preset parking boundary or starts driving without ignition on. In the case that it notes the unauthorized moving or driving, it sends emergency

- Power Down

- LED Indicator

- Events

- Parking Lock report immediately.

- Over speed Device can check speed of vehicle and send alert of over-speed to server.

- GPS Antenna Checking Device can alert when GPS antenna is disconnected. 3 Its applicable only for models that have external antenna. ST4310P User Manual

- Main Power Checking The device can recognize the main power and inform to server when main power line is disconnected or main power drops below preset value. Its applicable only for battery model.

- Battery Error Alert Device can alert about battery error related on charging. Its applicable only for battery model. 3. Protocol Construction All command and reports are string and follows below format. Every filed is distinguished by semi colon. All report string from device is ended by r (0x0D). Command message format (from server to device) HDR DEV_ID VER Field 1 Field 2 Field n Field HDR DEV_ID VER Definitions Remark String ST4310P + Command type 6 char. Device ID of AVL 02 Protocol Version. This is fixed with 02. Field 1 ~ n String Contents Device ID is unique number of each device that consists of 6digits. If the command has invalid value or DEV_ID of the command that is sent by NETWORK or SMS is not matched with DEV_ID of the unit. Report message format (from device to server) HDR DEV_ID SW_VER Field 1 Field 2 Field n Field HDR Definitions Remark String ST4310P + Report type 4 ST4310P User Manual DEV_ID VER Field 1 ~ n 6 char. Device ID of AVL 001 String Contents Software version that the device has. When the device is received a command, it responds with response string and changes some 4. Commands parameters or acts related operation. 4-1. Network Parameters Setting HDR DEV_ID VER AUTH APN USER_ID USER_PWD SEVER_IP SEVER_PORT B_SEVER_IP B_SEVER_IP SMS_NO PIN_NO Definition

: Set network parameters and PIN number. Definitions Unit Remark ST4310PNT Command type 0 /1/A NETWORK authentication Field HDR DEV_ID VER AUTH APN USER_ID USER_PWD SEVER_IP SEVER_PORT B_SEVER_IP B_SEVER_PORT SMS_NO W 6 char. 02 String String String String String String String String In this case, parameters in APN, USER_ID and USER_PWD field should be empty. Device ID Protocol Version 0 : PAP(NO in Synctrack) 1 : CHAP(YES in Synctrack) A : Automatic NETWORK set. Access Point Name ID for NETWORK Access Password for NETWORK Access Server IP Address Server Port Backup Server IP Address Backup Server Port Phone number what the device sends SMS report to. This can be used for backup in the area that if NETWORK condition is not good. Or, it can be used main report 5 ST4310P User Manual method when IP and Port are empty. For no use, it should be empty. String PIN Number to release PIN lock if it is enabled PIN_NO

<example>

<notes>

[command] ST4310PNTW;850000;02;0;internet;;;111.111.111.111;8600;;;;

[response] ST4310PNTW;Res;850000;010;0;internet;;; 111.111.111.111;8600;;;;

ST4310PNTW;Res;850000;010;A1;tim.br;tim;tim; 111.111.111.111;8600;;;;

** If network does not require User ID and Password, these fields should be empty. It the device is set to Automatic NETWORK Set, the device set NETWORK parameters automatically depending For example, if Airtel SIM is inserted, the device set AUTH to 0, APN to aitelNETWORK.com, USER_ID and And the device reports response string after adding real NETWORK parameters when automatic NETWORK Automatic NETWORK Set on inserted SIM. USER_PASS to empty. set is selected. HDR DEV_ID VER T1 T2 T3 A1 SND_DIST T4 SMS_T1 SMS_T2 SMS_PACK_NO 4-2. Report Parameter Setting ANGLE_RPT RPT_TYPE Definition

: Set parameters related on report interval. Field HDR DEV_ID VER T1 Definitions Unit Remark ST4310PRPT Command type 6 char. 02 String Device ID Protocol Version Range : 0 ~ 86400 vehicle starts parking. Sec Interval for sending status report in parking mode If 0, report in parking will be sent only one time when T2 String Sec Interval for sending status report in driving mode 6 ST4310P User Manual Range : 0 ~ 60000 starts driving. Range : 0 ~ 9999 If 0, report in driving will be sent only one time when vehicle String Sec Interval for sending status report in emergency mode If 0, emergency report will be sent only one time when emergency state occurs. String Number of attempts for emergency report until the device gets acknowledge from server If 0, no emergency report will be sent. Range : 0 ~ 60000 (60km) If 0, status report related on moving distance is disabled. If not 0, stats report is send when traveled distance reaches predefined SND_DIST. Interval for sending keep alive string Interval for sending status report in parking mode Interval for sending status report in driving mode Report No in one SMS message Degree Report STT message if its greater than ANGLE_RPT. SND_DIST String Meter Distance interval for sending status report. T4 SMS_T1 SMS_T2 SMS_PACK_NO ANGLE_RPT String String String String String Sec Min Min RPT_TYPE String Set the type of reporting. 0 : Disable Range : 1 ~ 179 0: FIFO : First in First Out. 1: LIFO : Last In First Out.

[command] ST4310PRPT;850000;02;180;120;60;3;0;0;0;0;0;0;0

[response] ST4310PRPT;Res;850000;010;180;120;60;3;0;0;0;0;0;0;0

<example>

<notes>

** If report interval is set big number, network may disconnect NETWORK connection because NETWORK communication is not progressed for a long time. So, unit may not receive command by NETWORK. T4 is for protecting against this disconnection by sending short data with short term.

** Alive report can be sent only when the device has no data to send during T4 interval. T3 A1 7 4-3. Event Parameter Setting ST4310P User Manual HDR DEV_ID VER IGNITION T1 T2 IN1_TYPE IN2_TYPE IN3_TYPE IN1_CHAT IN2_CHAT IN3_CHAT OUT1_TYPE OUT2_TYPE OUT1_ACTIVE OUT2_ACTIVE PULSE1_NO PULSE1_ON PULSE1_OFF PULSE2_NO PULSE2_ON PULSE2_OFF IN4_TYPE IN5_TYPE IN4_CHAT IN5_CHAT BAUD Definition

: Set parameter related event. Field HDR DEV_ID VER T1 T2 IN1_TYPE Definitions Unit Remark ST4310PEVT Command type Device ID Protocol Version 6 char. 02 String String 0 ~ 7 Sec Sec Delay for entering idle mode after ignition goes to off Delay for entering active mode after ignition goes to on 0 = Falling Edge 1 = Rising Edge 2 = Both Edge (Falling & Rising) 3 = Panic Button 4 = Call1 Button 5 = Call 2 Button 6 = Reserved 7 = Anti-Theft Button Default = 3. Range : 0 ~ 9999 Default = 3 sec. If 0, input1 is not checked. 13 = Disable Immobilizer if its activated by jammer detector. Only the device that included voice option (audio circuit) can be set to Call1 Button or Call2 Button. 8 IN1_CHAT String 100ms Input1 chattering time. ST4310P User Manual OUT1_TYPE 0 ~ 5 0 = GPIO 1 = immobilizer 2 = Immobilizer & Auto active automatically when the vehicle starts parking. Auto active means immobilizer is activated 4 = LED Out for indicating call status. Refer 7-2-3. 3 = Pulse 5 = Buzzer OUT1_ACTIVE 0 or 1 0 = Open when out1 is active 1 = GND when out1 is active PULSE1_NO String Pulse number when out1 type set to pulse. PULSE1_ON String 100ms Active time of pulse1 PULSE1_OFF String 100ms Inactive time of pulse1 Range : 0 ~ 9999 If pulse no is 9999, pulsing runs permanently. Range : 0 ~ 9999 It should be set with even number. Range : 0 ~ 9999 It should be set with even number. BAUD 0 ~ 4 Its available when extra events support RS232. Baud-rate 0 = No use 1 = 4800bps 2 = 9600bps 3 = 19200bps 4 = 38400bps 5 = 115200bps If the device does not support RS232, it should be 0. 9

<example>

<notes>

refer 6.3. ST4310P User Manual

[command] ST4310PEVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0

[response] ST4310PEVT;Res;850000;010;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0

** If IGNITION is set to 0, device doesnt check driving or parking state of the vehicle. It reports status string with idle mode always, and cannot support parking lock and the service that enters sleep or deep sleep automatically when the vehicle is parked.

** If IGNITION is set to 2, the device checks driving or parking state of the vehicle with voltage range of vehicles battery. We named it as Virtual Ignition. Virtual ignition can operate when the device installed into real vehicle and it may be need adjustment of voltage range for special vehicle. For setting method, please

** In case of pulse, pulse time may have tolerance about dozens of ms.

** Immobilizer, LED Blink line and Buzzer type cannot set both OUT1 and OUT2 simultaneously.

** In case that a event is set to door sensor, active state means door is opened.

** If device has the Handsfree kit, each time the volume up button is pressed once, the speaker volume is turned up as below. 0 -> 1 -> 2 -> 3 -> 4 ->5 ->0 -> 1 -> 2 ->3 -> 4 -> 5 - > 0 -> 1 -> .

(0 : Volume mute, 5 :Max Volume) Type of no supported event line is fixed to No Use. Below table is for example of 4 line event model. Field HDR DEV_ID VER IGNITION Definitions Unit Remark ST4310PEVT Command type 6 char. 02 0 ~ 2 Device ID Protocol Version Ignition using state 0 : Not use ignition 1 : Use ignition Line 2 : Virtual ignition(power) 3 : Virtual ignition (motion) T1 T2 String String Sec Sec Delay for entering idle mode after ignition goes to off Delay for entering active mode after ignition goes to on 10 ST4310P User Manual IN1_TYPE 0 ~ 5 0 = Falling Edge 1 = Rising Edge 2 = Both Edge (Falling & Rising) 3 = Panic Button 4 = Call1 Button 5 = Call 2 Button 6 = Reserved 7 = Anti-Theft Button Default = 3. Range : 0 ~ 9999 Default = 3 sec. If 0, input1 is not checked. 7 = No Use 13 = Disable Immobilizer if its activated by jammer detector. Only the device that included voice option (audio circuit) can be set to Call1 Button or Call2 Button. IN1_CHAT String 100ms Input1 chattering time. OUT1_ACTIVE 0 or 1 7 0 0 0 0 0 = No use

[command] ST4310PEVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0

[response] ST4310PEVT;Res;850000;010;1;60;0;3;8;8;30;0;0;6;6;1;0;0;0;0;0;0;0;8;8;0;0;0

** In case of event 4 line model, IN2_TYPE, IN3_TYPE, IN4_TYPE, IN5_TYPE, OUT1_TYPE and OUT2_TYPE should Type and chat time of non used event lines are set to No Use and 0 automatically although these filed of command is set to other value. 4-4. NETWORK Parameter Setting HDR DEV_ID VER SMS_LOCK SMS_MT1 SMS_MT2 SMS_MT3 SMS_MT4 IN_CALL_LOCK CALL_MT1 CALL_MT2 CALL_MT3 CALL_MT4 CALL_MT5 11 OUT1_TYPE PULSE1_NO PULSE1_ON PULSE1_OFF BAUD

<example>

<notes>

be No Use. ST4310P User Manual CALL_MO1 CALL_MO2 Definition

: Set parameters related SMS or Call. Definitions Unit Remark ST4310PNET Command type WORK 6 char. 02 Device ID Protocol Version SMS_LOCK 0 or 1 Lock of Receiving Commands by SMS Field HDR DEV_ID VER Disable (0) / Enable (1) If enabled, only commands that receives from SMS_MT1

~ MT3 number can be accepted. SMS_MT1 SMS_MT2 SMS_MT3 SMS_MT4 String String String String Up to 20 char. Phone number for SMS commands Up to 20 char. Phone number for SMS commands Up to 20 char. Phone number for SMS commands Up to 20 char. Phone number for SMS commands IN_CALL_LOCK 0 or 1 Lock of Incoming Call Disable (0) / Enable (1) If enabled, only call from CALL_MT1 ~ MT5 number can be accepted. Up to 20 char. Phone number for call Up to 20 char. Phone number for call Up to 20 char. Phone number for call Up to 20 char. Phone number for call Up to 20 char. Phone number for call String String String String String String String Up to 20 char. Phone number for outgoing call from device Up to 20 char. Phone number for outgoing call from device

[command] ST4310PNETWORK;850000;02;0;;;;;0;;;;;;;

[response] ST4310PNETWORK;Res;850000;010;0;;;;;0;;;;;;;

** When SMS or Call numbers are not set, that field should be empty. 4-5. Service Parameter Setting 12 CALL_MT1 CALL_MT2 CALL_MT3 CALL_MT4 CALL_MT5 CALL_MO1 CALL_MO2

<example>

<notes>

ST4310P User Manual HDR ZIP DEV_ID VER PARKING_LOCK SPEED_LIMIT PWR_DN CON_TYPE GROUP_SEND MP_CHK ANT_CHK BAT_CHK M_SENSOR CALL GEO_FENCE DATA_LOG ANTITHFT_CNT1 ANTITHFT_CNT2 JAM_DET JAM_CHK_DIST JAM_CHK_TM Definition

: Set parameters related report. Field HDR DEV_ID VER Definitions Unit Remark ST4310PSVC Command type 6 char. 02 Device ID Protocol Version PARKING_LOCK 0 or 1 Parking lock enable (1) / disable (0) SPEED_LIMIT String Km/h Over speed limit PWR_DN 0 ~ 2 Power saving type If 1, the device checks vehicle position in parking periodically. When the vehicle goes off some boundary or starts moving over some velocity, the device reports parking lock emergency. If 0, the device does not check over speed. If 1 and the vehicle runes over predefined value, device reports speed alerts once. 0 : Disabled sleep and deep sleep service 1 : Enabled deep sleep 2 : Enabled sleep CON_TYPE 0 ~ 2 Connection Type with Server ZIP 0 or 1 Use Zip 0 = KEEP_CON 1 = KEEP_DISCON 2 = KEEP_NOP Detail explanation is below. Disable (0) / Enable (1) 13 ST4310P User Manual GROUP_SEND 0 or 1 Group Send for stored data 0 : Disable 1 : Enable. One packet can include up to 5 reports. Group send is explained below. MP_CHK 0 or 1 Main Power Disconnection Check ANT_CHK 0 or 1 GPS Antenna Connection Error Check BAT_CHK 0 or 1 Backup Battery Error Check M_SENSOR 0 ~4 Motion Sensor Disable (0) / Enable (1) Disable (0) / Enable (1) Disable (0) / Enable (1) 0 1 2 3 4 5 6 7 Motion Disable Enable Disable Enable Disable Enable Disable Enable Collision Shock Disable Disable Disable Disable Enable Enable Enable Enable Disable Disable Enable Enable Disable Disable Enable Enable CALL 0 or 1 GEO_FENCE 0 or 1 Support Geo-fence DAT_LOG 0 or 1 Log out with RS232 Support Call with headset Disable (0) / Enable (1) Disable (0) / Enable (1) 0 = No Use 1 = Enable getting saved log data by RS232

[command] ST4310PSVC;850000;02;1;120;0;0;0;0;1;1;1;0;0;0;0;0;0;0;0;0

[response] ST4310PSVC;Res;850000;010;1;120;0;0;0;0;1;1;1;0;0;0;0;0;0;0;0;0

<example>

<notes>

** Function of M_SEMSOR can be used with the model that has motion sensor. If shock or collision detection is enabled, device will report to server when gets any shock or collision.

** If this parameter has been customized, This table should be disregarded and you should follow customized operation document. CON_TYPE 14 ST4310P User Manual 1. KEEP_CON : The device keeps TCP connection always and can receives a command by NETWORK. 2. KEEP_DISCON : The device connects TCP connection when the data is sent. After sending, the device disconnects NETWORK and TCP connection if it estimates there is no data for sending within 3minutes. In this case, it cannot receive a command by NETWORK. 3. KEEP_NOP : The device doesnt send any report after be installed. When the device enters emergency mode or receive Start Report command by SMS or RS232, it starts report depending on report parameters. It may be used for saving NETWORK fee. Current version cannot support this The device stores data if the vehicle is in no NETWORK area. And, the vehicle moves to NETWORK available If group send option is enabled, the device makes 5 reports to one bundle and send these 5 reports at one option. Group Send area, device starts sending stored data. time. M_Sensor Group send is useful to speed up sending. Jamming detection procedure 1. Collision: The device sending a event when ignition is ON and have a motion. 2. Shock: The device sending a event when ignition is OFF and have a motion. JAM_CHK_DIST & JAM_CHK_TM are assist for jamming detection to avoid false detection. At least, we recommend use JAM_CHK_DIST for safety. If you use two assist functions, it can detect two case of jamming as follows.

*Case of jamming NETWORK only. Jamming detected -> JAM_CHK_DIST -> JAM_CHK_TM -> Triggered by JAM_DET mode.

*Case of jamming NETWORK & GPS. Jamming detected -> JAM_CHK_TM -> Triggered by JAM_DET mode. JAM_CHK_DIST : if 0, skip this function. JAM_CHK_TM : if 0, skip this function. If disable all of assist functions, just triggered by HAM_DET mode after detected jamming. In this case, its possible to false detection in weak NETWORK or strong radio area. 4-6. Additional Parameters 15 ST4310P User Manual HDR DEV_ID VER SVR_TYPE B_SVR_TYPE UDP_ACK DEV_PORT Definition

: Setting additional parameter requested. Field HDR DEV_ID VER SVR_TYPE Definitions Unit Remark ST4310PADP Command type 6 char. 02 T / U Device ID Protocol Version Server Protocol Type B_SVR_TYPE T / U Backup Server Protocol Type UDP_ACK 0 ~ 3 ACK from Server when UPD is used. T : TCP U : UDP T : TCP U : UDP 0 : No use DEV_PORT String Devices port for receiving command from UDP server. 1 : ACK when the server receives reports except alive. 2 : ACK when the server receives reports except STT and alive report. 3 : ACK when the server receives emergency report. Command response doesnt need ACK. It can be used only when UDP server is used. If 0 or empty, the device would use port 9000. If not zero, the device can receive commands with port DEV_PORT. 0 0 0 0 0 0 Reserved Reserved Reserved Reserved Reserved Reserved

<example>

<notes>

[command] ST4310PADP;850000;02;U;T;2;9000;0;0;0;0;0;0

[response] ST4310PADP;Res;850000;022;U;T;2;9000;0;0;0;0;0;0 16 ST4310P User Manual This command can be applied from software version 22. ACK in case of UDP UDP is protocol that doesnt check whether the data is transmitted successfully. So, the device checks completion of sending with ACK depending on UDP_ACK type. ACK is sent by server when the data is received. If the ACK is not sent during more than 2 minutes after sending, the device recognizes the data was not reached to server and sends the data again. Examples of ACK report are as below. String Format : ST4310PACK;850000 Zip Format : 0x15 0x85 0x00 0x00 It is recommended ACK_TYPE is set to 1 to confirm all data can be transmitted safely. Report Type UDP_ACK=0 UDP_ACK=1 UDP_ACK=2 UDP_ACK=3 Alive STT Event, Alert, Etc. Emergency X X X X X O O O X X O O X X X O 4-7. Set Parameters of Main Voltage HDR DEV_ID VER CHR_STOP_THRES_12 DECIDE_BAT_12 OPERATION_STOP_THRES_12 IGNDET_H IGNDET_L Definition

: Set some value of main voltage. Field HDR Definitions Remark ST4310PMBV Command type 17 ST4310P User Manual DEV_ID VER 6 char. Device ID 02 Protocol Version CHR_STOP_THRES_12 String Voltage value to stop backup battery charging in 12V DECIDE_BAT_12 String Voltage value to check whether the vehicles battery is OPERATION_STOP_THRES_12 String Voltage value to protect vehicle battery. vehicle. 12V. Default = 0 Default = 0 The device operation stops if car battery voltage is lower than this value in vehicle that has 12V power. In case of virtual ignition, the vehicle can recognize driving String state when vehicle power is more than IGNDET_H. String In case of virtual ignition, the vehicle can recognize parking state when vehicle power is less than IGNDET_L.

[command] ST4310PMBV;850000;02;10.5;22;19;8.00;18.00;0;0

[response] ST4310PMBV;Res;850000;122;10.5;22;19;8.00;18.00;0;0 IGNDET_H IGNDET_L

<example>

<note>

IGNDET_H and IGNDET_L are 0, device check parking and driving automatically. 4-8. Set Parameters of Motion Sensor HDR DEV_ID VER CHR_STOP_THRES_12 DECIDE_BAT_12 OPERATION_STOP_THRES_12 IGNDET_H IGNDET_L VI_ON_THRES VI_ON_DELAY VI_ON_PERCENT VI_OFF_THRES VI_OFF_DELAY VI_OFF_PERCENT Definition

: Set motion sensor parameters Field HDR DEV_ID VER Definitions Unit Remark ST4310PMSR Command type 6 char. 02 Protocol Version Device ID 0 Disable SHOCK_DELAY String Sec. Delay for entering shock detection mode after ignition off 18 ST4310P User Manual Range : 1 ~ 21600 (5hour) Recommend : 600 ( 10 min.) MOTION_THRES String Step Detection level of shock violation. SHOCK_THRES String Step Detection level of shock violation. COLL_THRES String Step Gravity for collision report. VI_ON_THRES String 1/255G Threshold value for Motion Virtual Ignition On VI_ON_DELAY String Sec. Delay time for Motion Virtual Ignition On VI_ON_PERCENT String

Percent for Motion Virtual Ignition On. VI_OFF_THRES String 1/255G Threshold value for Motion Virtual Ignition Off VI_OFF_DELAY String Sec. Delay time for Motion Virtual Ignition Off VI_OFF_PERCENT String

Percent for Motion virtual Ignition Off. Range : 0.04 ~ 2.0 Recommend : 0.04 Range : 0.04 ~ 2.0 Recommend : 0.04 Range : 0.1 ~ 2.0 Recommend : 0.7 Range : 3~50 Default : 5 Range : 3~999 Default : 10 Range : 30~100 Default: 70 Range : 3~50 Default : 5 Range : 3~999 Default : 10 Range : 30 ~ 100 Default : 70

[command] ST4310PMSR;;02;600;0.04;0.04;0.7;5;10;70;5;10;70

[response] ST4310PMSR;Res;852588;128;600;0.04;0.04;0.70;5;10;70;5;10;70

<example>

<notes>

as it for shock detection.

* For the shock level, we recommend it to set to 0.04. if it's over than 0.04, the sensor will be more insensitive 19 4-11. Control Command ST4310P User Manual HDR DEV_ID VER CMD_ID Definition

: Controls some functions. Field HDR DEV_ID VER CMD_ID Definitions Unit Remark ST4310PCM Command type D 6 char. 01 String Device ID Protocol Version Control command content Caution : If its not correct the Unit ID, ignored. If received, the device sends status string instantly.

[response] ST4310PSTT;850000;010;20090724;07:12:16;00129;+37.479995;+126.885815;000.029;000.00;

4-11-1. Status Request Definition

: Location poll, request of the status report. Field CMD_ID Definitions Unit Remark StatusReq Status request

<example>

<example>

[command] ST4310PCMD;850000;02;StatusReq 7;1;0;15.33;100000;2;0002 4-11-2. Reset Definition

: Reset all of parameters. Field CMD_ID Definitions Unit Remark Reset Reset 20 ST4310P User Manual Initialize all parameters with factory value and reboot the device.

<example>

[command] ST4310PCMD;850000;02;Reset

[response] ST4310PCMD;Res;850000;010;Reset 4-11-3. Preset Definition

: Reset all of parameters. Field CMD_ID

<example>

Definitions Unit Remark Preset Report parameter setting values and current device status. Response includes network, report, event, NETWORK and service parameters. It includes status of device, also.

[command] ST4310PCMD;850000;02;Preset

[response] ST4310PCMD;Res;850000;010;Preset;

NTW;0;internet;;;111.111.111.111;8600;;;;1234;

RPT;60;180;120;60;3;0;0;;;;

EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0;

NETWORK;0;;;;;0;;;;;;;;

SVC;1;120;0;0;0;0;1;1;1;0;0;0;0 DEV;0;0;0;0

[response] event 4 line model NTW;0;internet;;;111.111.111.111;8600;;;;1234;

RPT;60;180;120;60;3;0;0;;;;

EVT;1;60;0;3;8;8;30;0;0;6;6;1;0;0;0;0;0;0;0;0;0;0;0;0;

NETWORK;0;;;;;0;;;;;;;;

SVC;1;120;0;0;0;0;1;1;1;0;0;0;0 DEV;0;0;0;0

<notes>

** After power on, device sends response string of preset once.

** DEV filed informs current status of device as below. OUT1 OUT2 PWR_DN BAT_CON 0 = Disable 0 = Disable 0 = Normal 0

Backup battery is 21 ST4310P User Manual 1 = Enable 1 = Enable 1 = Sleep disconnected. 2 = Deep sleep 1 = Backup battery is connected. Definitions Unit Remark PresetA Report all parameters including additional parameter. Field CMD_ID

<example>

[command] ST4310PCMD;850000;02;PresetA

[response] ST4310PCMD;Res;850000;010;PresetA;

NTW;0;internet;;;111.111.111.111;8600;;;;1234;

RPT;60;180;120;60;3;0;0;;;;

EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0;

NETWORK;0;;;;;0;;;;;;;;

SVC;1;120;0;0;0;0;1;1;1;0;0;0;0;

ADP;U;T;2;9000;0;0;0;0;0;0;

DEV;0;0;0;0;0;0;0;0

<notes>

** This command can be applied from software version 22.

** DEV filed informs current status of device as below. OUT1 OUT2 PWR_DN 0 = Disable 0 = Disable 0 = Normal 1 = Enable 1 = Enable 1 = Sleep 2 = Deep sleep BAT_CON 0

Backup battery is disconnected. 1 = Backup battery is connected. TRACKING Anti-Theft Reserved Reserved 0 = Stop Tracking 0 = Disable 1 = Start Tracking 1 = Enable 4-11-4. ACK of Emergency 22 Definition

: Stop emergency report. ST4310P User Manual Field CMD_ID

<example>

Definitions Unit Remark AckEmerg Acknowledgement of emergency report. The device will stop emergency reports if it is in emergency state.

[command] ST4310PCMD;850000;02;AckEmerg

[response] ST4310PCMD;Res;850000;010;AckEmerg Field CMD_ID

<example>

Definitions Unit Remark Enable1 Enable Output1

[command] ST4310PCMD;850000;02;Enable1

[response] ST4310PCMD;Res;850000;010;Enable1

[response] ST4310PCMD;Res;850000;010;Enable1NoUse (in case that IN type is set to No Use).

** If OUT1 set with immobilizer, output1 line goes to active status gradually with pulse in driving mode.

** If OUT1 set with pulse type, output1 line generates pulse and returns inactive state after pulsing out 4-11-5. Enable1 Definition

: Active Output1.

<notes>

** Output1 line goes to active status. automatically. 4-11-6. Disable1 Definition

: Inactive Output1. Field CMD_ID

<example>

Definitions Unit Remark Disable1 Disable Output1

[command] ST4310PCMD;850000;02;Disable1 23 ST4310P User Manual

[response] ST4310PCMD;Res;850000;010;Disable1

[response] ST4310PCMD;Res;850000;010;Disable1NoUse (in case that IN type is set to No Use).

<notes>

** Output1 line goes to inactive status. 4-11-9. Request IMSI Definition

: Request the unique SIM ID. Field CMD_ID

<example>

Definitions Unit Remark ReqIMSI Request IMSI (unique SIM ID) If received, device sends IMSI of using SIM.

[command] ST4310PCMD;850000;02;ReqIMSI

[response] ST4310PCMD;Res;850000;010;ReqIMSI;724031111553779 Definitions Unit Remark ReqICCID Request ICCID (sequence number that is displayed on SIM) If received, device sends ICCID of using SIM. 4-11-10. Request ICCID Definition

: Request the ICCID. Field CMD_ID

<example>

4-11-11. ReqVer

[command] ST4310PCMD;850000;02;ReqICCID

[response] ST4310PCMD;Res;850000;010;ReqICCID;89550230000084256668 Definition

: Request software version. Field CMD_ID Definitions Unit Remark ReqVer Request device version Device reports Model, Buyer, Protocol and S/W release version. 24 ST4310P User Manual

<example>

[command] ST4310PCMD;850000;02;ReqVer

[response] ST4310PCMD;Res;850000;010;ReqVer;ST4310PE_SAMPLE_STBASE_001 4-11-12. Erase All Definition

: Erase all of data in buffer. Definitions Unit Remark EraseAll Erase saved all reports and disable outputs. This is needed to initialize just before device is delivered to a customer. Field CMD_ID

<example>

Field CMD_ID

<example>

[command] ST4310PCMD;850000;02;EraseAll

[response] ST4310PCMD;Res;850000;010;EraseAll 4-11-13. Initialize Traveled Distance Definition

: Initialize the travel distance. Definitions Unit Remark InitDist Set traveled distance to 0.

[command] ST4310PCMD;850000;02;InitDist

[response] ST4310PCMD;Res;850000;010;InitDist 4-11-14. Initialize Message Number Definition

: Initialize the message sequence number. Field CMD_ID Definitions Unit Remark InitMsgNo Set message number to 0. 25 ST4310P User Manual

<example>

[command] ST4310PCMD;850000;02;InitMsgNo

[response] ST4310PCMD;Res;850000;010;InitMsgNo 4-11-23. Reboot Definition

: reboot unit. Field CMD_ID

<example>

Definitions Unit Remark Reboot Reboot device.

[command] ST4310PCMD;850000;02;Reboot

[response] ST4310PCMD;Res;850000;010;Reboot 4-11-24. Request SIM IP Address Definition

: Request of the local IP address in SIM card. Field CMD_ID

<example>

Definitions Unit Remark ReqSIMIP SIM card IP request

[command] ST4310PCMD;850000;02;ReqSIMIP

[response] ST4310PCMD;Res;850000;010;ReqSIMIP;172.16.18.6 26 ST4310P User Manual 4. Trouble Shooting (LED Indicator) 4.1 Blue LED: Indicates NETWORK status. NETWORK Blink Count Remarks Normal 1 Server Com. Error 2

<Possible Cause>

1. Server or network parameter is wrong. 2. Server is closed. 3. Temporary network barrier

<Possible Cause>

1. Network parameter is wrong. 2. SIM is blocked about NETWORK using. 3. Temporary network barrier 4. Weak NETWORK signal 5. NETWORK antenna connection is not firm.

<Possible Cause>

1. NETWORK antenna is disconnected. 2. NETWORK antenna or socket of NETWORK antenna is broken. 3. Device is broken.

<Possible Cause>

1. SIM PIN is enabled.

<Possible Cause>

1. Weak NETWORK signal. 2. NETWORK antenna connection is not firm. 27 NETWORK Com. 3 Error No Network 4 SIM PIN Locked 5 Cannot Attach NW 6 ST4310P User Manual No SIM 7

<Possible Cause>

1. There is no SIM or SIM is not inserted properly. 2. SIM or SIM socket is broken. 28 ST4310P User Manual 4.2 RED LED: Indicates GPS status. Blink Count Remarks GPS Normal No Fix 1 2 1. If power on, GPS chipset is trying to find position during some

<Possible Cause>

minutes. 2. GPS antenna lays on weak or no GPS signal position 3. GPS antenna connection is not firm.

<Possible Cause>

1. GPS antenna is disconnected. 2. GPS antenna or socket of GPS antenna is broken. 3. Unit is broken. GPS Chipset Error 4 GPS Antenna Error

[FCC Warning Statement]

FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment.

[IC Warning Statement]

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible 29 ST4310P User Manual den compromettre le fonctionnement.

[EN] FCC and IC RF Radiation Exposure Statement: This equipment complies with FCC and IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

[FR] RF du FCC et IC d'exposition aux radiations: Cet quipement est conforme l'exposition de FCC et IC rayonnements RF limites -tablies pour un environnement non contrl. Lantenne pour ce transmetteur ne doit pas tre mme endroit avec dautres metteur sauf conformment FCC et IC procdures de produits Multi-metteur. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps.

*. Caution : Dont use USB Connect. USB Connect is only use for production. This device does not use LORA and LTEM1 together. 30

Label Information

<Bottom view of EUT>

Label Contains FCC ID : XMR201707BG96 Contains IC : 10224A-201709BG96 FCC ID : WA2ST4310P IC : 21484-ST4310P This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

A-1706, 1705 Greatvalley, 32, Digital-ro 9-gil, Geumcheon-gu, Seoul, Republic of Korea Suntech International Ltd. FCC Agent Authorization letter April 9, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:

I, the undersigned, hereby authorize Lab Manager Hyunchae, You of SGS Korea Co., Ltd. and hereafter referred to as SGS Korea, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Lab Manager Hyunchae, You of SGS Korea Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SGS Korea as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

A-1706, 1705 Greatvalley, 32, Digital-ro 9-gil, Geumcheon-gu, Seoul, Republic of Korea Suntech International Ltd. e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

specified standards;

manner;

Division;

f) use certification only to indicate the products are certified as being in conformity with g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification i) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely yours, Name/Title : Yohan Kim / General Manager Company Name : Suntech International Ltd.

Suntech International Ltd. A-1706, 1705 Greatvalley, 32, Digital-ro 9-gil, Geumcheon-gu, Seoul, Republic of Korea FCC Confidentiality Request Letter April 9, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 RE : Request of Confidentiality for FCC ID : WA2ST4310P To Whom It May Concern:

Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, The Suntech International hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give The Suntech International temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows:

Permanent Short-Term CONFIDENTIAL LIST 1 2 3 4 5 6 7 Block Diagram Operational Descriptions Schematics External Photos Internal Photos Test-Setup Photos Users Manual Suntech International Ltd. A-1706, 1705 Greatvalley, 32, Digital-ro 9-gil, Geumcheon-gu, Seoul, Republic of Korea The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely yours, Name/Title : Yohan Kim / General Manager Company Name : Suntech International Ltd.