FCC ID: WA2ST330 Vehicle Tracker

ST330 User Manual Suntech International Ltd. ST330 User Manual 1. Introduction This document describes features, protocols and detail operation of ST330. If there is another operation description document for special buyer to customize or model and the contents of the document is different with this, customizing document should be applied for special buyer. 2. Overview Device consists of GPRS, GPS and event parts. The main purpose of device reports getting GPS position and other informs of vehicle to server periodically. Device can control or check connected lines and support additional functions. 2-1. Operation Mode The device has 3 operation modes, driving, parking and emergency.

** Driving

** Parking

** Emergency

: Driving status when ignition is on.

: Parking status that starts if ignition is off during more than T1.

: Once panic button is On or any other status as per designed. The device sends emergency reports until A1 times or receiving server acknowledge. 2-2. Report AVL reports GPS and some information at predefined interval, depending on the current modes. Also, AVL sends some alerts, for example, movement at the parking condition, changing of connected input line and so on. Device distinguishes all reports with 6 types, Status report, emergency, event, alert, alive and command response. Device can store reports when reporting route (For example, GPRS condition) is not successful. Storage capacity is up to 2,000 status reports, 50 emergency reports, 50 alert reports (include event reports) and 1500 bytes as command response. In case of status reports, oldest report is erased and new report is buffered when the buffer is full and new status report enters (FIFO). When reporting condition is recovered, device starts sending all buffered reports. Also, this capacity can increase if it is needed. Each type of reports has priority, and priority is as below. Emergency Command Response Alert Status Report Alive (Lowest) 2 ST330 User Manual Emergency is the first to be sent after recovering GPRS condition. 2-3. Setting Parameter Parameters of device can be changed by GPRS or SMS, and some control can be realized also in the same way. Detail protocols are described in Chapter 4. 2-4. Features Key features are described here;

- Power Down Device can process two steps of power-down, Sleep and Deep Sleep, for reducing power consumption when the vehicle is parked.

- LED Indicator LED indicates GPRS and GPS states. Its helpful to check error cause.

- Events Device has 2 output lines, 3 input lines and ignition line.

- Update Firmware by Over The Air (FOTA) When Firmware of device has some error or has to be changed for a new service to be implemented, device can update internal ROM file by over the air (FOTA), remotely via GPRS. Customers do not need to visit every vehicle to download the new firmware. Method of FOTA describes at SunTech_OTA_UA_Protocol document in detail.

- Parking Lock Device can check whether the vehicle moves off the preset parking boundary or starts driving without ignition on. In the case that it notes the unauthorized moving or driving, it sends emergency report immediately.

- Over speed Device can check speed of vehicle and send alert of over-speed to server.

- GPS Antenna Checking Device can alert when GPS antenna is disconnected. 3 ST330 User Manual Its applicable only for models that have external antenna.

- Main Power Checking The device can recognize the main power and inform to server when main power line is disconnected or main power drops below preset value. Its applicable only for battery model.

- Battery Error Alert Device can alert about battery error related on charging. Its applicable only for battery model. 3. Protocol Construction All command and reports are string and follows below format. Every filed is distinguished by semi colon. All report string from device is ended by r (0x0D). Command message format (from server to device) HDR DEV_ID VER Field 1 Field 2 Field n Field HDR DEV_ID VER Field 1 ~ n Definitions Remark String 6 char. 02 String SA200 + Command type Device ID of AVL Protocol Version. This is fixed with 02. Contents Device ID is unique number of each device that consists of 6digits. If the command has invalid value or DEV_ID of the command that is sent by GPRS or SMS is not matched with DEV_ID of the unit. Report message format (from device to server) HDR DEV_ID SW_VER Field 1 Field 2 Field n Field HDR Definitions Remark String SA200 + Report type 4 ST330 User Manual DEV_ID VER Field 1 ~ n 6 char. 001 String Device ID of AVL Software version that the device has. Contents 4. Commands When the device is received a command, it responds with response string and changes some parameters or acts related operation. 4-1. Network Parameters Setting HDR DEV_ID VER AUTH APN USER_ID USER_PWD SEVER_IP SEVER_PORT B_SEVER_IP B_SEVER_IP SMS_NO PIN_NO

: Set network parameters and PIN number. Definition Field HDR DEV_ID VER AUTH Definitions SA200NTW 6 char. 02 0 /1/A Unit Remark Command type Device ID Protocol Version GPRS authentication 0 : PAP(NO in Synctrack) 1 : CHAP(YES in Synctrack) A : Automatic GPRS set. In this case, parameters in APN, USER_ID and USER_PWD field should be empty. Access Point Name ID for GPRS Access Password for GPRS Access Server IP Address Server Port Backup Server IP Address Backup Server Port Phone number what the device sends SMS report to. This can be used for backup in the area that if GPRS condition is not good. Or, it can be used main report method when IP and Port are empty. 5 APN USER_ID USER_PWD SEVER_IP SEVER_PORT B_SEVER_IP B_SEVER_PORT SMS_NO String String String String String String String String ST330 User Manual For no use, it should be empty. String PIN_NO

<example>

[command] SA200NTW;850000;02;0;internet;;;111.111.111.111;8600;;;;

[response] SA200NTW;Res;850000;010;0;internet;;; 111.111.111.111;8600;;;;

PIN Number to release PIN lock if it is enabled SA200NTW;Res;850000;010;A1;tim.br;tim;tim; 111.111.111.111;8600;;;;

<notes>

** If network does not require User ID and Password, these fields should be empty. Automatic GPRS Set It the device is set to Automatic GPRS Set, the device set GPRS parameters automatically depending on inserted SIM. For example, if Airtel SIM is inserted, the device set AUTH to 0, APN to aitelgprs.com, USER_ID and USER_PASS to empty. And the device reports response string after adding real GPRS parameters when automatic GPRS set is selected. 4-2. Report Parameter Setting HDR DEV_ID VER T1 T2 T3 A1 SND_DIST T4 SMS_T1 SMS_T2 SMS_PACK_NO ANGLE_RPT RPT_TYPE Definition Field HDR DEV_ID VER T1 T2

: Set parameters related on report interval. Definitions Unit Remark SA200RPT 6 char. 02 String Sec Command type Device ID Protocol Version Interval for sending status report in parking mode Range : 0 ~ 86400 If 0, report in parking will be sent only one time when vehicle starts parking. String Sec Interval for sending status report in driving mode Range : 0 ~ 60000 6 ST330 User Manual T3 A1 String Sec String If 0, report in driving will be sent only one time when vehicle starts driving. Interval for sending status report in emergency mode Range : 0 ~ 9999 If 0, emergency report will be sent only one time when emergency state occurs. Number of attempts for emergency report until the device gets acknowledge from server If 0, no emergency report will be sent. SND_DIST String Meter Distance interval for sending status report. Range : 0 ~ 60000 (60km) If 0, status report related on moving distance is disabled. If not 0, stats report is send when traveled distance reaches predefined SND_DIST. T4 SMS_T1 SMS_T2 SMS_PACK_NO ANGLE_RPT String String String String String Sec Min Min Interval for sending keep alive string Interval for sending status report in parking mode Interval for sending status report in driving mode Report No in one SMS message Degree Report STT message if its greater than ANGLE_RPT. RPT_TYPE String 0 : Disable Range : 1 ~ 179 Set the type of reporting. 0: FIFO : First in First Out. 1: LIFO : Last In First Out.

<example>

[command] SA200RPT;850000;02;180;120;60;3;0;0;0;0;0;0;0

[response] SA200RPT;Res;850000;010;180;120;60;3;0;0;0;0;0;0;0

<notes>

** If report interval is set big number, network may disconnect GPRS connection because GPRS communication is not progressed for a long time. So, unit may not receive command by GPRS. T4 is for protecting against this disconnection by sending short data with short term.

** Alive report can be sent only when the device has no data to send during T4 interval. 4-3. Event Parameter Setting 7 ST330 User Manual HDR DEV_ID VER IGNITION T1 T2 IN1_TYPE IN2_TYPE IN3_TYPE IN1_CHAT IN2_CHAT IN3_CHAT OUT1_TYPE OUT2_TYPE OUT1_ACTIVE OUT2_ACTIVE PULSE1_NO PULSE1_ON PULSE1_OFF PULSE2_NO PULSE2_ON PULSE2_OFF IN4_TYPE IN5_TYPE IN4_CHAT IN5_CHAT BAUD Definition Field HDR DEV_ID VER T1 T2 IN1_TYPE

: Set parameter related event. Definitions SA200EVT 6 char. 02 String String 0 ~ 7 Unit Sec Sec IN1_CHAT String 100ms Remark Command type Device ID Protocol Version Delay for entering idle mode after ignition goes to off Delay for entering active mode after ignition goes to on 0 = Falling Edge 1 = Rising Edge 2 = Both Edge (Falling & Rising) 3 = Panic Button 4 = Call1 Button 5 = Call 2 Button 6 = Reserved 7 = Anti-Theft Button 13 = Disable Immobilizer if its activated by jammer detector. Default = 3. Only the device that included voice option (audio circuit) can be set to Call1 Button or Call2 Button. Input1 chattering time. Range : 0 ~ 9999 Default = 3 sec. If 0, input1 is not checked. 8 ST330 User Manual OUT1_TYPE 0 ~ 5 0 = GPIO 1 = immobilizer 2 = Immobilizer & Auto active Auto active means automatically immobilizer is activated OUT1_ACTIVE 0 or 1 PULSE1_NO String when the vehicle starts parking. 3 = Pulse 4 = LED Out for indicating call status. Refer 7-2-3. 5 = Buzzer 0 = Open when out1 is active 1 = GND when out1 is active Pulse number when out1 type set to pulse. Range : 0 ~ 9999 If pulse no is 9999, pulsing runs permanently. PULSE1_ON String 100ms Active time of pulse1 PULSE1_OFF String 100ms BAUD 0 ~ 4 Range : 0 ~ 9999 It should be set with even number. Inactive time of pulse1 Range : 0 ~ 9999 It should be set with even number. Its available when extra events support RS232. Baud-rate 0 = No use 1 = 4800bps 2 = 9600bps 3 = 19200bps 4 = 38400bps 5 = 115200bps If the device does not support RS232, it should be 0. 9 ST330 User Manual

<example>

[command] SA200EVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0

[response] SA200EVT;Res;850000;010;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0

<notes>

** If IGNITION is set to 0, device doesnt check driving or parking state of the vehicle. It reports status string with idle mode always, and cannot support parking lock and the service that enters sleep or deep sleep automatically when the vehicle is parked.

** If IGNITION is set to 2, the device checks driving or parking state of the vehicle with voltage range of vehicles battery. We named it as Virtual Ignition. Virtual ignition can operate when the device installed into real vehicle and it may be need adjustment of voltage range for special vehicle. For setting method, please refer 6.3.

** In case of pulse, pulse time may have tolerance about dozens of ms.

** Immobilizer, LED Blink line and Buzzer type cannot set both OUT1 and OUT2 simultaneously.

** In case that a event is set to door sensor, active state means door is opened.

** If device has the Handsfree kit, each time the volume up button is pressed once, the speaker volume is turned up as below. 0 -> 1 -> 2 -> 3 -> 4 ->5 ->0 -> 1 -> 2 ->3 -> 4 -> 5 - > 0 -> 1 -> .

(0 : Volume mute, 5 :Max Volume) Type of no supported event line is fixed to No Use. Below table is for example of 4 line event model. Field HDR DEV_ID VER IGNITION T1 T2 Definitions Unit Remark SA200EVT 6 char. 02 0 ~ 2 Command type Device ID Protocol Version Ignition using state 0 : Not use ignition 1 : Use ignition Line 2 : Virtual ignition(power) 3 : Virtual ignition (motion) String String Sec Sec Delay for entering idle mode after ignition goes to off Delay for entering active mode after ignition goes to on 10 ST330 User Manual IN1_TYPE 0 ~ 5 0 = Falling Edge 1 = Rising Edge 2 = Both Edge (Falling & Rising) 3 = Panic Button 4 = Call1 Button 5 = Call 2 Button 6 = Reserved 7 = Anti-Theft Button 13 = Disable Immobilizer if its activated by jammer detector. Default = 3. Only the device that included voice option (audio circuit) can be set to Call1 Button or Call2 Button. IN1_CHAT String 100ms OUT1_TYPE OUT1_ACTIVE PULSE1_NO PULSE1_ON PULSE1_OFF BAUD 7 0 or 1 0 0 0 0 Input1 chattering time. Range : 0 ~ 9999 Default = 3 sec. If 0, input1 is not checked. 7 = No Use 0 = No use

<example>

[command] SA200EVT;850000;02;1;60;0;3;2;2;30;20;20;1;0;1;0;0;0;0;0;0;0;0;0;0;0;0

[response] SA200EVT;Res;850000;010;1;60;0;3;8;8;30;0;0;6;6;1;0;0;0;0;0;0;0;8;8;0;0;0

<notes>

** In case of event 4 line model, IN2_TYPE, IN3_TYPE, IN4_TYPE, IN5_TYPE, OUT1_TYPE and OUT2_TYPE should be No Use. Type and chat time of non used event lines are set to No Use and 0 automatically although these filed of command is set to other value. 4-4. GSM Parameter Setting HDR DEV_ID VER SMS_LOCK SMS_MT1 SMS_MT2 SMS_MT3 11 ST330 User Manual SMS_MT4 IN_CALL_LOCK CALL_MT1 CALL_MT2 CALL_MT3 CALL_MT4 CALL_MT5 CALL_MO1 CALL_MO2

: Set parameters related SMS or Call. Definition Field HDR DEV_ID VER Definitions SA200GSM 6 char. 02 SMS_LOCK 0 or 1 Unit Remark Command type Device ID Protocol Version Lock of Receiving Commands by SMS Disable (0) / Enable (1) If enabled, only commands SMS_MT1 ~ MT3 number can be accepted. that receives from SMS_MT1 SMS_MT2 SMS_MT3 SMS_MT4 String String String String Up to 20 char. Phone number for SMS commands Up to 20 char. Phone number for SMS commands Up to 20 char. Phone number for SMS commands Up to 20 char. Phone number for SMS commands IN_CALL_LOCK 0 or 1 Lock of Incoming Call Disable (0) / Enable (1) If enabled, only call from CALL_MT1 ~ MT5 number can be accepted. CALL_MT1 CALL_MT2 CALL_MT3 CALL_MT4 CALL_MT5 CALL_MO1 String String String String String String Up to 20 char. Phone number for call Up to 20 char. Phone number for call Up to 20 char. Phone number for call Up to 20 char. Phone number for call Up to 20 char. Phone number for call Up to 20 char. Phone number for outgoing call from device Phone number for outgoing call from device String Up to 20 char. CALL_MO2

<example>

[command] SA200GSM;850000;02;0;;;;;0;;;;;;;

[response] SA200GSM;Res;850000;010;0;;;;;0;;;;;;;

<notes>

** When SMS or Call numbers are not set, that field should be empty. 4-5. Service Parameter Setting 12 ST330 User Manual HDR ZIP DEV_ID VER PARKING_LOCK SPEED_LIMIT PWR_DN CON_TYPE GROUP_SEND MP_CHK ANT_CHK BAT_CHK M_SENSOR CALL GEO_FENCE DATA_LOG ANTITHFT_CNT1 ANTITHFT_CNT2 JAM_DET JAM_CHK_DIST JAM_CHK_TM Definition Field HDR DEV_ID VER PARKING_LOCK

: Set parameters related report. Definitions Unit Remark SA200SVC 6 char. 02 0 or 1 Command type Device ID Protocol Version Parking lock enable (1) / disable (0) If 1, the device checks vehicle position in parking periodically. When the vehicle goes off some boundary or starts moving over some velocity, the device reports parking lock emergency. SPEED_LIMIT String Km/h Over speed limit PWR_DN 0 ~ 2 CON_TYPE 0 ~ 2 ZIP 0 or 1 GROUP_SEND 0 or 1 If 0, the device does not check over speed. If 1 and the vehicle runes over predefined value, device reports speed alerts once. Power saving type 0 : Disabled sleep and deep sleep service 1 : Enabled deep sleep 2 : Enabled sleep Connection Type with Server 0 = KEEP_CON 1 = KEEP_DISCON 2 = KEEP_NOP Detail explanation is below. Use Zip Disable (0) / Enable (1) Group Send for stored data 0 : Disable 1 : Enable. One packet can include up to 5 reports. Group send is explained below. 13 ST330 User Manual MP_CHK 0 or 1 ANT_CHK 0 or 1 BAT_CHK 0 or 1 M_SENSOR 0 ~4 CALL 0 or 1 GEO_FENCE 0 or 1 DAT_LOG 0 or 1 Main Power Disconnection Check Disable (0) / Enable (1) GPS Antenna Connection Error Check Disable (0) / Enable (1) Backup Battery Error Check Disable (0) / Enable (1) Motion Sensor 0 1 2 3 4 5 6 7 Motion Disable Enable Disable Enable Disable Enable Disable Enable Collision Disable Disable Disable Disable Enable Enable Enable Enable Shock Disable Disable Enable Enable Disable Disable Enable Enable Support Call with headset Disable (0) / Enable (1) Support Geo-fence Disable (0) / Enable (1) Log out with RS232 0 = No Use 1 = Enable getting saved log data by RS232

<example>

[command] SA200SVC;850000;02;1;120;0;0;0;0;1;1;1;0;0;0;0;0;0;0;0;0

[response] SA200SVC;Res;850000;010;1;120;0;0;0;0;1;1;1;0;0;0;0;0;0;0;0;0

<notes>

** Function of M_SEMSOR can be used with the model that has motion sensor. If shock or collision detection is enabled, device will report to server when gets any shock or collision.

** If this parameter has been customized, This table should be disregarded and you should follow customized operation document. CON_TYPE 1. KEEP_CON : The device keeps TCP connection always and can receives a command by GPRS. 2. KEEP_DISCON : The device connects TCP connection when the data is sent. After sending, the device disconnects GPRS and TCP connection if it estimates there is no data for sending within 14 ST330 User Manual 3minutes. In this case, it cannot receive a command by GPRS. 3. KEEP_NOP : The device doesnt send any report after be installed. When the device enters emergency mode or receive Start Report command by SMS or RS232, it starts report depending on report parameters. It may be used for saving GPRS fee. Current version cannot support this option. Group Send The device stores data if the vehicle is in no GPRS area. And, the vehicle moves to GPRS available area, device starts sending stored data. If group send option is enabled, the device makes 5 reports to one bundle and send these 5 reports at one time. Group send is useful to speed up sending. M_Sensor 1. Collision: The device sending a event when ignition is ON and have a motion. 2. Shock: The device sending a event when ignition is OFF and have a motion. Jamming detection procedure JAM_CHK_DIST & JAM_CHK_TM are assist for jamming detection to avoid false detection. At least, we recommend use JAM_CHK_DIST for safety. If you use two assist functions, it can detect two case of jamming as follows.

*Case of jamming GPRS only. Jamming detected -> JAM_CHK_DIST -> JAM_CHK_TM -> Triggered by JAM_DET mode.

*Case of jamming GPRS & GPS. Jamming detected -> JAM_CHK_TM -> Triggered by JAM_DET mode. JAM_CHK_DIST : if 0, skip this function. JAM_CHK_TM : if 0, skip this function. If disable all of assist functions, just triggered by HAM_DET mode after detected jamming. In this case, its possible to false detection in weak GSM or strong radio area. 4-6. Additional Parameters HDR DEV_ID VER SVR_TYPE B_SVR_TYPE UDP_ACK DEV_PORT Definition

: Setting additional parameter requested. 15 ST330 User Manual Definitions Unit Remark Field HDR DEV_ID VER SVR_TYPE SA200ADP 6 char. 02 T / U B_SVR_TYPE T / U UDP_ACK 0 ~ 3 DEV_PORT String Reserved Reserved Reserved Reserved Reserved 0 0 0 0 0 Command type Device ID Protocol Version Server Protocol Type T : TCP U : UDP Backup Server Protocol Type T : TCP U : UDP ACK from Server when UPD is used. 0 : No use 1 : ACK when the server receives reports except alive. 2 : ACK when the server receives reports except STT and alive report. 3 : ACK when the server receives emergency report. Command response doesnt need ACK. Devices port for receiving command from UDP server. It can be used only when UDP server is used. If 0 or empty, the device would use port 9000. If not zero, the device can receive commands with port DEV_PORT. 0 Reserved

<example>

[command] SA200ADP;850000;02;U;T;2;9000;0;0;0;0;0;0

[response] SA200ADP;Res;850000;022;U;T;2;9000;0;0;0;0;0;0

<notes>

This command can be applied from software version 22. ACK in case of UDP 16 ST330 User Manual UDP is protocol that doesnt check whether the data is transmitted successfully. So, the device checks completion of sending with ACK depending on UDP_ACK type. ACK is sent by server when the data is received. If the ACK is not sent during more than 2 minutes after sending, the device recognizes the data was not reached to server and sends the data again. Examples of ACK report are as below. String Format : SA200ACK;850000 Zip Format : 0x15 0x85 0x00 0x00 It is recommended ACK_TYPE is set to 1 to confirm all data can be transmitted safely. Report Type UDP_ACK=0 UDP_ACK=1 UDP_ACK=2 UDP_ACK=3 X O O O Alive STT Event, Alert, Etc. Emergency X X X X 4-7. Set Parameters of Main Voltage X X O O X X X O HDR DEV_ID VER CHR_STOP_THRES_12 CHR_STOP_THRES_24 DECIDE_BAT_24 OPERATION_STOP_THRES_12 OPERATION_STOP_THRES_24 IGNDET_H IGNDET_L

: Set some value of main voltage. Definitions SA200MBV Command type Remark 6 char. Device ID 02 Protocol Version Definition Field HDR DEV_ID VER 17 ST330 User Manual CHR_STOP_THRES_12 DECIDE_BAT_24 String String OPERATION_STOP_THRES_12 String IGNDET_H IGNDET_L String String Voltage value to stop backup battery charging in 12V vehicle. Voltage value to check whether the vehicles battery is 12V. Voltage value to protect vehicle battery. The device operation stops if car battery voltage is lower than this value in vehicle that has 12V power. In case of virtual ignition, the vehicle can recognize driving state when vehicle power than IGNDET_H. Default = 0 is more In case of virtual ignition, the vehicle can recognize parking state when vehicle power is less than IGNDET_L. Default = 0

<example>

[command] SA200MBV;850000;02;10.5;22;19;8.00;18.00;0;0

[response] SA200MBV;Res;850000;122;10.5;22;19;8.00;18.00;0;0

<note>

IGNDET_H and IGNDET_L are 0, device check parking and driving automatically. 4-8. Set Parameters of Motion Sensor HDR DEV_ID VER CHR_STOP_THRES_12 CHR_STOP_THRES_24 DECIDE_BAT_24 OPERATION_STOP_THRES_12 OPERATION_STOP_THRES_24 IGNDET_H IGNDET_L VI_ON_THRES VI_ON_DELAY VI_ON_PERCENT VI_OFF_THRES VI_OFF_DELAY VI_OFF_PERCENT Definition Field HDR DEV_ID VER SHOCK_DELAY

: Set motion sensor parameters Definitions SA200MSR 6 char. 02 String Unit Remark Command type Device ID Protocol Version Sec. Delay for entering shock detection mode after ignition off 0 Disable 18 ST330 User Manual Range : 1 ~ 21600 (5hour) Recommend : 600 ( 10 min.) MOTION_THRES String Step Detection level of shock violation. Range : 0.04 ~ 2.0 Recommend : 0.04 SHOCK_THRES String Step Detection level of shock violation. Range : 0.04 ~ 2.0 Recommend : 0.04 COLL_THRES String Step Gravity for collision report. Range : 0.1 ~ 2.0 Recommend : 0.7 VI_ON_THRES String 1/255G Threshold value for Motion Virtual Ignition On VI_ON_DELAY String Sec. VI_ON_PERCENT String

%

Range : 3~50 Default : 5 Delay time for Motion Virtual Ignition On Range : 3~999 Default : 10 Percent for Motion Virtual Ignition On. Range : 30~100 Default: 70 VI_OFF_THRES String 1/255G Threshold value for Motion Virtual Ignition Off VI_OFF_DELAY String Sec. VI_OFF_PERCENT String

%

Range : 3~50 Default : 5 Delay time for Motion Virtual Ignition Off Range : 3~999 Default : 10 Percent for Motion virtual Ignition Off. Range : 30 ~ 100 Default : 70

<example>

[command] SA200MSR;;02;600;0.04;0.04;0.7;5;10;70;5;10;70

[response] SA200MSR;Res;852588;128;600;0.04;0.04;0.70;5;10;70;5;10;70

<notes>

* For the shock level, we recommend it to set to 0.04. if it's over than 0.04, the sensor will be more insensitive as it for shock detection. 19 ST330 User Manual 4-11. Control Command HDR DEV_ID VER CMD_ID Definition Field HDR DEV_ID VER CMD_ID

: Controls some functions. Definitions Unit Remark SA200CMD 6 char. 01 String Command type Device ID Protocol Version Control command content Caution : If its not correct the Unit ID, ignored. 4-11-1. Status Request Definition

: Location poll, request of the status report. Field CMD_ID Definitions Unit Remark StatusReq Status request If received, the device sends status string instantly.

<example>

<example>

[command] SA200CMD;850000;02;StatusReq

[response] SA200STT;850000;010;20090724;07:12:16;00129;+37.479995;+126.885815;000.029;000.00;

7;1;0;15.33;100000;2;0002 4-11-2. Reset Definition Field CMD_ID

: Reset all of parameters. Definitions Unit Remark Reset Reset 20 ST330 User Manual Initialize all parameters with factory value and reboot the device.

<example>

[command] SA200CMD;850000;02;Reset

[response] SA200CMD;Res;850000;010;Reset 4-11-3. Preset Definition Field CMD_ID

: Reset all of parameters. Definitions Unit Remark Preset Report parameter setting values and current device status. Response includes network, report, event, GSM and service parameters. It includes status of device, also.

<example>

[command] SA200CMD;850000;02;Preset

[response] SA200CMD;Res;850000;010;Preset;

NTW;0;internet;;;111.111.111.111;8600;;;;1234;

RPT;60;180;120;60;3;0;0;;;;

EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0;

GSM;0;;;;;0;;;;;;;;

SVC;1;120;0;0;0;0;1;1;1;0;0;0;0 DEV;0;0;0;0

[response] event 4 line model NTW;0;internet;;;111.111.111.111;8600;;;;1234;

RPT;60;180;120;60;3;0;0;;;;

EVT;1;60;0;3;8;8;30;0;0;6;6;1;0;0;0;0;0;0;0;0;0;0;0;0;

GSM;0;;;;;0;;;;;;;;

SVC;1;120;0;0;0;0;1;1;1;0;0;0;0 DEV;0;0;0;0

<notes>

** After power on, device sends response string of preset once.

** DEV filed informs current status of device as below. OUT1 0 = Disable OUT2 0 = Disable PWR_DN BAT_CON 0 = Normal 0

=

Backup battery is 21 ST330 User Manual 1 = Enable 1 = Enable 1 = Sleep 2 = Deep sleep disconnected. 1 = Backup battery is connected. Unit Definitions PresetA Field CMD_ID

<example>

[command] SA200CMD;850000;02;PresetA

[response] SA200CMD;Res;850000;010;PresetA;

Remark Report all parameters including additional parameter. NTW;0;internet;;;111.111.111.111;8600;;;;1234;

RPT;60;180;120;60;3;0;0;;;;

EVT;1;60;0;3;2;2;30;20;20;1;1;1;0;0;0;0;0;0;0;0;0;0;0;0;

GSM;0;;;;;0;;;;;;;;

SVC;1;120;0;0;0;0;1;1;1;0;0;0;0;

ADP;U;T;2;9000;0;0;0;0;0;0;

DEV;0;0;0;0;0;0;0;0

<notes>

** This command can be applied from software version 22.

** DEV filed informs current status of device as below. OUT1 0 = Disable 1 = Enable OUT2 0 = Disable 1 = Enable PWR_DN 0 = Normal 1 = Sleep 2 = Deep sleep BAT_CON

=

battery Backup 0 disconnected. 1 = Backup battery is connected. is TRACKING Anti-Theft Reserved Reserved 0 = Stop Tracking 1 = Start Tracking 0 = Disable 1 = Enable 4-11-4. ACK of Emergency 22 Definition Field CMD_ID ST330 User Manual

: Stop emergency report. Definitions Unit Remark AckEmerg Acknowledgement of emergency report. The device will stop emergency reports if it is in emergency state.

<example>

[command] SA200CMD;850000;02;AckEmerg

[response] SA200CMD;Res;850000;010;AckEmerg 4-11-5. Enable1 Definition

: Active Output1. Unit Definitions Enable1 Remark Enable Output1 Field CMD_ID

<example>

[command] SA200CMD;850000;02;Enable1

[response] SA200CMD;Res;850000;010;Enable1

[response] SA200CMD;Res;850000;010;Enable1NoUse (in case that IN type is set to No Use).

<notes>

** Output1 line goes to active status.

** If OUT1 set with immobilizer, output1 line goes to active status gradually with pulse in driving mode.

** If OUT1 set with pulse type, output1 line generates pulse and returns inactive state after pulsing out automatically. 4-11-6. Disable1 Definition

: Inactive Output1. Field Definitions Unit Remark Disable1 CMD_ID

<example>

[command] SA200CMD;850000;02;Disable1 Disable Output1 23 ST330 User Manual

[response] SA200CMD;Res;850000;010;Disable1

[response] SA200CMD;Res;850000;010;Disable1NoUse (in case that IN type is set to No Use).

<notes>

** Output1 line goes to inactive status. 4-11-9. Request IMSI Definition

: Request the unique SIM ID. Field CMD_ID Definitions Unit Remark ReqIMSI Request IMSI (unique SIM ID) If received, device sends IMSI of using SIM.

<example>

[command] SA200CMD;850000;02;ReqIMSI

[response] SA200CMD;Res;850000;010;ReqIMSI;724031111553779 4-11-10. Request ICCID Definition

: Request the ICCID. Field CMD_ID Definitions ReqICCID Unit Remark Request ICCID (sequence number that is displayed on SIM) If received, device sends ICCID of using SIM.

<example>

[command] SA200CMD;850000;02;ReqICCID

[response] SA200CMD;Res;850000;010;ReqICCID;89550230000084256668 4-11-11. ReqVer Definition

: Request software version. Field CMD_ID Definitions Unit Remark ReqVer Request device version Device reports Model, Buyer, Protocol and S/W release version. 24 ST330 User Manual

<example>

[command] SA200CMD;850000;02;ReqVer

[response] SA200CMD;Res;850000;010;ReqVer;SA200E_SAMPLE_STBASE_001 4-11-12. Erase All Definition

: Erase all of data in buffer. Field CMD_ID Definitions Unit Remark EraseAll Erase saved all reports and disable outputs. This is needed to initialize just before device is delivered to a customer.

<example>

[command] SA200CMD;850000;02;EraseAll

[response] SA200CMD;Res;850000;010;EraseAll 4-11-13. Initialize Traveled Distance Definition

: Initialize the travel distance. Field Definitions Unit Remark InitDist CMD_ID

<example>

[command] SA200CMD;850000;02;InitDist

[response] SA200CMD;Res;850000;010;InitDist Set traveled distance to 0. 4-11-14. Initialize Message Number Definition

: Initialize the message sequence number. Field CMD_ID Definitions Unit Remark InitMsgNo Set message number to 0. 25 ST330 User Manual

<example>

[command] SA200CMD;850000;02;InitMsgNo

[response] SA200CMD;Res;850000;010;InitMsgNo 4-11-23. Reboot Definition

: reboot unit. Unit Definitions Reboot Field CMD_ID

<example>

[command] SA200CMD;850000;02;Reboot

[response] SA200CMD;Res;850000;010;Reboot Remark Reboot device. 4-11-24. Request SIM IP Address Definition

: Request of the local IP address in SIM card. Field Definitions Unit Remark ReqSIMIP CMD_ID

<example>

[command] SA200CMD;850000;02;ReqSIMIP

[response] SA200CMD;Res;850000;010;ReqSIMIP;172.16.18.6 SIM card IP request 26 ST330 User Manual Event Cable Color pin Description Red: VCC (12V) Black: Ground White: Input1. Panic Button When Input1 goes to GND, then ST330 change Emergency mode. It reports emergency string by mode 1 in Emergency mode such that SA200EMG;850000;20081017;07:41:56;00100;+37.478519;+126.886819;000.012;000.00;9;1;0;15.30;

110000;1 Orange: Output1. Immobilizer activation behaves progressive blocking when vehicle is driving. The progressive blocking diagram is as below. The active time of the immobilizer increases 90ms each 4s. After 3minutes, immobilizer is activated continuously. When one of output is dedicated to PULSE, it operates as below. Time for activation and deactivation is configurable by PULSE_ON and PULSE_OFF in Service Parameter. Pulse time may have tolerance about dozens of milliseconds. Active and inactive state is decided by output line number. Active state of Output 1 is open(Hi-Z) and active state of output 2 is ground. 3.6 Check GPS/GPRS operation and battery charger operation with LEDs. It takes 3~10 minutes for GPS connected. Caution: Direction of ST330 is very important when installed in the vehicle. Make sure that top side of ST330 27 ST330 User Manual 4. Trouble Shooting (LED Indicator) 4.1 Blue LED: Indicates GPRS status. GPRS Normal Blink Count Remarks 1 Server Com. Error 2

<Possible Cause>

1. Server or network parameter is wrong. 2. Server is closed. 3. Temporary network barrier

<Possible Cause>

1. Network parameter is wrong. 2. SIM is blocked about GPRS using. 3. Temporary network barrier 4. Weak GPRS signal 5. GPRS antenna connection is not firm.

<Possible Cause>

1. GPRS antenna is disconnected. 2. GPRS antenna or socket of GPRS antenna is broken. 3. Device is broken.

<Possible Cause>

1. SIM PIN is enabled.

<Possible Cause>

1. Weak GPRS signal. 2. GPRS antenna connection is not firm.

<Possible Cause>

1. There is no SIM or SIM is not inserted properly. 2. SIM or SIM socket is broken. 28 GPRS Com. Error 3 No Network 4 SIM PIN Locked 5 Cannot NW Attach 6 No SIM 7 ST330 User Manual 4.2 RED LED: Indicates GPS status. GPS Normal No Fix Blink Count Remarks 1 2 GPS Chipset Error GPS Antenna Error 4

<Possible Cause>

1. If power on, GPS chipset is trying to find position during some minutes. 2. GPS antenna lays on weak or no GPS signal position 3. GPS antenna connection is not firm.

<Possible Cause>

1. GPS antenna is disconnected. 2. GPS antenna or socket of GPS antenna is broken. 3. Unit is broken. The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface in a residential installation. Cautions Modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 29 ST330 User Manual NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. 30