INSTALLATION MANUAL N2 NANO POWER Octa Band Digital Radios 20dBm per Band Integrated Antennas Integrated Bluetooth NANO POWER 20dBm Octa Band Digital Radio Revision History Revision Number 1.0.1 Revision Date 1st June 2019 Summary of Changes New Format Author Allen Chu Copyright 2019 Sunwave All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from Sunwave. All copyright, confidential information, patents, design rights and all other intellectual property rights of whatsoever nature contained herein are and shall remain the sole and exclusive property of Sunwave. The information furnished herein is believed to be accurate and reliable. However, no responsibility is assumed by Sunwave for its use, or for any infringements of patents or other rights of third parties resulting from its use. The Sunwave and CrossFire names and logos are trademarks or registered trademarks of Sunwave. All other trademarks are the property of their respective owners. Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 2 of 24 NANO POWER 20dBm Octa Band Digital Radio Content General......................................................................................................................................................................................................... 5 Warnings.............................................................................................................................................................................................. 5 Site Considerations..............................................................................................................................................................................6 Environmental...................................................................................................................................................................................... 6 Preparation...................................................................................................................................................................................................7 Unpacking and Inspection.....................................................................................................................................................................7 Tools....................................................................................................................................................................................................10 N2RU Power Supply............................................................................................................................................................................ 10 Installation of the A2.................................................................................................................................................................................. 12 Mount the A2 in the Rack................................................................................................................................................................... 12 Attach A2 handle.........................................................................................................................................................................12 Attach sliding rails and A2 to rack.............................................................................................................................................. 12 Connect power and ground cable to A2..................................................................................................................................... 13 Mount the A2 on the Wall...................................................................................................................................................................14 Attach handle to A2....................................................................................................................................................................14 Mount A2 to wall.........................................................................................................................................................................14 Connect power and ground cable to A2..................................................................................................................................... 15 Installation of the EU-O...............................................................................................................................................................................16 Mount the EU-O in the Rack................................................................................................................................................................16 Mount the EU-O on the Wall............................................................................................................................................................... 16 Installation of the N2RU.............................................................................................................................................................................. 17 N2RU Ceiling Installation (with suspended ceiling)............................................................................................................................. 17 Assemble Bracket I&II..................................................................................................................................................................17 Place the bracket.........................................................................................................................................................................17 Assemble Bracket II.................................................................................................................................................................... 18 Buckle Up and Connect Wire.......................................................................................................................................................19 To perform maintenance on the N2RU.......................................................................................................................................20 Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 3 of 24 NANO POWER 20dBm Octa Band Digital Radio N2RU Ceiling Installation (without suspended ceiling)....................................................................................................................... 21 Draw Circles for plastic expansion nails......................................................................................................................................21 Assemble Mounting Bracket.......................................................................................................................................................22 Buckle Up and Connect Wire...................................................................................................................................................... 22 To perform maintenance on the N2RU.......................................................................................................................................24 Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 4 of 24 NANO POWER 20dBm Octa Band Digital Radio General The CrossFire system components are designed for maximum safety and reliability when they are installed, used, and maintained by trained and qualified technicians in accordance with the procedures and instructions contained in this manual. To assure the safe operation of your system, always follow the safety and operational recommendations in this manual. Warnings CrossFire is not a consumer product. Please install and use CrossFire in accordance with the instructions. Before installing or modifying any equipment of CrossFire, read and fully understand the entire instructions in this guide. Only qualified personnel are authorized to install and maintain the CrossFire system. Changes or modifications to the CrossFire equipment not expressly approved by the manufacturer could void the product warranty and the users authority to operate the equipment. Follow Electro Static Discharge precautions to avoid any damage of PCB, PSU etc. Keep equipment powered-off during installing or modifying. Low pathloss cables connected to antennas are highly recommended. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC License to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. This is NOT a CONSUMER device. It is designed for installation by an installer approved by an ISED licensee. You MUST have an ISED LICENCE or the express consent of an ISED licensee to operate this device. To comply with FCC RF exposure compliance requirements, each individual antenna used for this transmitter must be installed to provide a separation distance greater than 20cm or more from all persons during normal operation and must not be co-
located with any other antenna for meeting RF exposure requirements. To comply with RSS-102 RF exposure compliance requirements, each individual antenna used for this transmitter must be installed to provide a separation distance greater than 20cm or more from all persons during normal operation and must not be co-located with any other antenna for meeting RF exposure requirements. Cet quipement est conforme aux limites d'exposition aux radiations IC CNR102 tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Antenna gain should not exceed 3 dBi. Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 5 of 24 NANO POWER 20dBm Octa Band Digital Radio If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. Note: Only authorized person can enter the area where the antenna is installed. And the person is fully aware of the potential for exposure and can exercise control over his or her exposure by leaving the area or by some other appropriate means. Awareness of the potential for RF exposure in a workplace or similar environment can be provided through specific training as part of a RF safety program NOTE: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Site Considerations The system delay should be taken into consideration when there are neighboring BTS sites overlapping in coverage Pick an ideal easy-to-reach location for installation convenience. Verify that there is a minimum of a 50cm radius of space around CrossFire equipment for convenience of maintenance and on-
site inspection. Install Master A2 close to the service area for monitor and debugging. Environmental Humidity and temperature have adverse efforts on reliability of the CrossFire system. Therefore, it is highly recommended to install the equipment in locations with stable humidity, temperature and ventilating. The equipment has to operate at humidity level and temperature range as follow:
Maximum humidity: 85%
Temperature range: -10 to 40 Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 6 of 24 NANO POWER 20dBm Octa Band Digital Radio Preparation Unpacking and Inspection Unpack and inspect the packages as the following procedure:
1. 2. 3. Open the shipping packages carefully for each unit from the protective packing sponge. Ensure that all equipment and accessories have been delivered. Ensure that all equipment and accessories have no damage. If there is any damage, contact your Sunwave service agent. A2 Accessories Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 7 of 24 NANO POWER 20dBm Octa Band Digital Radio EU-O Accessories Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 8 of 24 NANO POWER 20dBm Octa Band Digital Radio N2 Accessories Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 9 of 24 Tools Electric drill, cross screw, cutter, ladder and other tools are needed for N2RU installation which are not offered from Sunwave for now. All of these tools are for customers to prepare NANO POWER 20dBm Octa Band Digital Radio Philips Screwdriver M6 and M3 Drilling Machine Pen Allen Wrench T5 Combination Spanner 17mm N2RU Power Supply For CrossFire N2RU system, it needs DC power to supply N2RU at remote side. Here are 2 methods for power supply AC/DC power adapter and power supply unit (PSU). When using AC/DC power adapter, all you need is to prepare an AC power cable which have proper paired connect for adapter. However, if AC power source for each adapter is not available, you can also have PSU (56V) to make N2RU work. Figure 1. N2RU Power Adapter Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 10 of 24 NANO POWER 20dBm Octa Band Digital Radio Here is some specification for cable design power supply unit (PSU):
Pn = 78W Power consumption of N2RU Pw = 22W Pin = Vin*Iin = 100W Vin = 56V Iin = Pin/Vin = 1.786 Pin = 100W max for class 2 installation Voltage of N2 PSU Iin = Max injected current to not exceed 100W Rw = Pw/Iw2 = 6.8992 Rw = Rd*D If N2 consumes 95W then 5W is dissipated in the wire (Pw) Rw = resistance of the wire D = distance of the wire (total length of supply + return cable) Rd = resistance per meter of the wire Cable type 12 AWG 14 AWG 16 AWG Voltage Drop ohms/meter 0.00557 0.00928 0.0147 D=Rw/Rd 2x distance between PSU and N2RU (there and back) 1239 743 469 Max Fiber Distance Distance between PSU and N2RU 619 372 235 N2RU Configuration Power 2T2R - B25, B66 2T2R - B25, B66, B7 2T2R - B5, B25, B66, B7 4T4R - B25, B66 78W 88W 95W 98W Max Distance @ AWG 12 619 338 169 56 14 32 203 101 34 16 235 128 64 21 Power connector is stripped and tinned as below. Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 11 of 24 Installation of the A2 Mount the A2 in the Rack Attach A2 handle NANO POWER 20dBm Octa Band Digital Radio 1. Attach the 19" mounting brackets at the front of the A2, using 4 screws M316 per bracket and the Phillips screwdriver. Observe the orientation of the brackets
(Figure 2). Figure 2. Attaching a 19" Mounting Bracket Attach sliding rails and A2 to rack 1. Attach the sliding rails to the rack
(Figure 3) Note: the sliding rails is not included in delivery. Figure 3. Attached Sliding Rails 2. Place the A2 in the rack (Figure 4) Figure 4. Place A2 in Rack Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 12 of 24 NANO POWER 20dBm Octa Band Digital Radio 3. Secure the A2 using 2 screws M616 on both side and the Phillips screwdriver
(Figure 5). Figure 5. Fix A2 with Screws For rack installation, it is highly recommended to use fan in the middle of 2 adjacent A2. Figure 6. Separation of adjacent A2s Connect power and ground cable to A2 1. Connect and lock the power cable at the A2 rear side (Figure 7). Figure 7. Connect Power Cable at Rear Side 2. Connect and screw the ground wire at the A2 rear side (Figure 8). Figure 8. Connect Ground Cable at Rear Side Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 13 of 24 NANO POWER 20dBm Octa Band Digital Radio Mount the A2 on the Wall Attach handle to A2 Attach the 19" mounting brackets to the A2 rear, using 4 screws M316 per bracket and the Phillips screwdriver. Observe the orientation of the brackets shown in Figure 9. Mount A2 to wall Figure 9. Attaching a 19" Mounting Bracket 1. Hold the A2 to the installation location and mark the position of the 4 mounting holes in the mounting brackets; see arrows in Figure 10 2. Drill the mounting holes according to the chosen mounting accessories. 3. Attach the dowels, expansion screws or the like and fasten the A2 to the wall (Figure 11). Figure 10. Marking position of mounting holes Figure 11. Mounting completed Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 14 of 24 Connect power and ground cable to A2 NANO POWER 20dBm Octa Band Digital Radio 1. Connect and lock the power cable at the A2 rear side (Figure 12) Figure 12. Connect power cable at rear side 2. Connect and screw the ground wire at the A2 rear side (Figure 13) Figure 13. Connect ground cable at rear side Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 15 of 24 NANO POWER 20dBm Octa Band Digital Radio Installation of the EU-O Installing the EU-O is virtually the same as installing the A2. Please refer to the steps described in A2 installation for the EU-O. Mount the EU-O in the Rack Proceed as described under Mount the A2 in the Rack to mount the EU-O in the rack and connect the power and the ground cable. Mount the EU-O on the Wall Proceed as described under Mount the A2 on the Wall to mount the EU-O on the wall and connect the power and the ground cable Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 16 of 24 Installation of the N2RU N2RU Ceiling Installation (with suspended ceiling) Assemble Bracket I&II NANO POWER 20dBm Octa Band Digital Radio 1. Assemble Mounting Bracket I & IV with 6 x M3 x 6 screws. Figure 14. Assembling bracket I & bracket II 2. Lace Bracket I & IV combo with Nylon Cable Tie Figure 15. Lacing Mounting Bracket Place the bracket 1. Drill a hole with diameter of 90mm for putting Mounting Bracket I & IV on ceiling upside. Figure 16. Drilling a Hole Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 17 of 24 NANO POWER 20dBm Octa Band Digital Radio 2. Lay Mounting Bracket I & IV at ceiling upside for immobilization of N2RU. Figure 17. Placing bracket 1 3. Make the nylon tie hang down through the hole. Figure 18. Placing bracket 2 Assemble Bracket II 1. Assemble Mounting Bracket II to Mounting Bracket I using 2 X M6 X 70 screws, Flat Washer M6 and Spring Washer M6. Note: Mounting Bracket III is already assembled into N2RU in factory Figure 19. Assemble bracket II Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 18 of 24 Buckle Up and Connect Wire 2. Buckle the bar side of N2RU up to Mounting Bracket III. NANO POWER 20dBm Octa Band Digital Radio Figure 20. Buckle up 3. Connect power cable and fiber cable to N2RU Figure 21. Wire Connection Diagram 4. Buckle the rotary hook side of N2RU to Mounting Bracket III Figure 22. Installation Completed Diagram Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 19 of 24 NANO POWER 20dBm Octa Band Digital Radio 7. Tighten the M3 x 3 screws 1. Press the button of hook at N2RU to expose top panel of N2RU for debugging and maintenance Figure 23. Tighten N2RU To perform maintenance on the N2RU Figure 24. Unlock Rotary Hook Diagram 1 Figure 25. Unlock Rotary Hook Diagram 2 Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 20 of 24 N2RU Ceiling Installation (without suspended ceiling) Draw Circles for plastic expansion nails NANO POWER 20dBm Octa Band Digital Radio 1. Using the Mounting Bracket III keyholes as guides, mark the position of the 2 holes to be drilled Into the ceiling. Figure 26. Drawing Circles Diagram 1 2. Drill 2 holes with diameter of 10mm and depth of 55mm at the position in step 1 Figure 27. Drilling Holes Diagram 1 3. Insert plastic expansion nails into holes by hammer Figure 28. Insert Plastic Expansion Nails Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 21 of 24 NANO POWER 20dBm Octa Band Digital Radio Assemble Mounting Bracket 1. Assemble Mounting Bracket III to ceiling using ST6.3 X 50 screws. Figure 29. Assembling Bracket III Diagram 1 Figure 30. Assembling Bracket III Diagram 2 Buckle Up and Connect Wire 2. Buckle the bar side of N2RU up to Mounting Bracket III. Figure 31. Buckle up Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 22 of 24 NANO POWER 20dBm Octa Band Digital Radio 3. Connect power cable and fiber cable to N2RU Figure 32. Wire Connection Diagram 4. Buckle the rotary hook side of N2RU to Mounting Bracket III Figure 33. Installation Completed Diagram 7. Tighten the M3 x 3 screws Figure 34. Tighten N2RU Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 23 of 24 To perform maintenance on the N2RU NANO POWER 20dBm Octa Band Digital Radio 1. Press the button of hook at N2RU to expose top panel of N2RU for debugging and maintenance Figure 35. Unlock Rotary Hook Diagram 1 Figure 36. Unlock Rotary Hook Diagram 2 Contact us today:
www.sunwaveglobal.com marketing@sunwaveglobal.com Sunwave IM_CF_N2 v1.0.1 | 24 of 24