FCC ID: YJW-10652PG 15W Wireless Charging Pad

15W FAST WIRELESS CHARGING PAD Specs Wireless Charging Pad:

Input: 5VDC/2A; 9VDC/1.67A; 12VDC/1.5A Output: Up to 15W (Fast Charge)**

*Charging time may vary based on device.

**NOTE: 20W USB-C Power Adapter is required (not included) to enable fast wireless charging. H S I L G N E CAUTION:

DO NOT place any credit cards or other types of magnetic material near the charging pad. This product can ONLY be charged using the provided adapters and cables. Do not attempt to disassemble the wireless charging pad as it may short circuit or damage the product. Keep this product in a dry and ventilated space. Do not place in direct heat or use in high humidity environments. Do not use organic solvents to clean surface. 2 3 E N G L I S H Using your Fast Wireless Charging Pad 1. Connect the USB-C cable to the USB-C port on your Fast Wireless Charging Pad. 2. Plug the USB-C connector into the wall charger. (USB-C wall charger not included.) 3. Plug in the wall charger. 4. Place your Qi-enabled device on the Fast Wireless Charging Pad with the screen facing up. The LED is white when your device is charging. Charging Indicator Light Status:

ORANGE LIGHT: Device is not charging properly. Please reposition your device until you see the white light come on. WHITE LIGHT: Device is charging. H S I L G N E Lifetime Warranty This product is fully warranted against defects in materials and workmanship for the lifetime of the product, so long as the manufacturer continues to make this product. If a product fails due to a manufacturing defect, we will replace it upon proper proof of purchase by the original purchaser. Replacement product will be subject to shipping and handling charges. Damages through normal wear and tear, alteration, misuse, neglect, accident, service by anyone other than the authorized service center, or act of God, are not covered by this warranty. For all warranty claims, the product must be returned in accordance with PureGears return policy. USB-C is a trademark of USB Implementers Forum. The Qi symbol is a trademark of the Wireless Power Consortium. All trademarks and trade names are used for reference purposes only and are the property of their respective owners. 4 5 FCC Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

E N G L I S H

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. FCC Interference Statement (cont.) This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, maybe cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. H S I L G N E If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into and outlet on a circuit different form that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected. 6 7 E N G L I S H 15W Base de carga inalmbrica rpida 8 Especificaciones Base de carga inalmbrica:

Entrada: 5Vc.c./2A; 9Vc.c./1.67A; 12Vc.c./1.5A Salida: hasta 15W (Carga rpida)**

*Los tiempos de carga pueden variar dependiendo del tipo de dispositivo

**NOTA: Se requiere un adaptador de corriente USB-C de 20W

(no incluido) para permitir una carga inalmbrica rpida E S P A O L PRECAUCIN:

NO coloque ninguna tarjeta de crdito ni ningn otro tipo de material magntico cerca del panel de carga. Este producto SLO puede cargarse usando los cables y adaptadores suministrados. No intente desarmar el panel de carga inalmbrico, ya que puede causar un cortocircuito o daar el producto. Mantenga este producto en un lugar seco y ventilado. No lo exponga al calor directo ni lo utilice en ambientes de mucha humedad. No utilice solventes orgnicos para limpiar la superficie. Cmo usar la base de carga inalmbrica 1. Conecte el cable USB-C al puerto USB-C en la base de carga inalmbrica. 2. Enchufe el conector USB-C al cargador de pared.

(No incluye el cargador de pared USB-C.) 3. Conecte el adaptador de corriente a la toma de corriente. 4. Coloque su dispositivo habilitado con Qi en la base de carga inalmbrica con la pantalla mirando hacia arriba. La luz LED estar blanca mientras el dispositivo se est cargando. Estado del indicador de carga:

LUZ NARANJA: El dispositivo no se est cargando correctamente. LUZ BLANCA: Cargando L O A P S E 10 11 Garanta limitada de por vida Este producto est completamente garantizado contra defectos en materiales y mano de obra durante la vida til del producto, siempre y cuando el fabricante contine fabricando este producto. Si un producto falla debido a un defecto de fabricacin, lo reemplazaremos con la comprobacin de compra adecuada del comprador original. El producto de reemplazo estar sujeto a cargos de manejo y envo. Esta garanta no cubre los daos por uso y desgaste normal, alteracin, mal uso, negligencia, accidente, servicio realizado por alguien que no sea el centro de servicio autorizado o caso fortuito. Para todos los reclamos de garanta, el producto debe devolverse de acuerdo con la poltica de devolucin de PureGear. USB-C es una marca comercial de USB Implementers Forum. El smbolo Qi es una marca registrada de Wireless Power Consortium. Todas las marcas comerciales y nombres comerciales se usan nicamente para propsitos de referencia y son propiedad de sus respectivos dueos. E S P A O L Declaracin de interferencia de la FCC Este dispositivo cumple con la Parte 15 de las reglas de la FCC. Su operacin est sujeta a las siguientes dos condiciones:

(1) este dispositivo no debe provocar interferencia daina, y

(2) este dispositivo debe aceptar la interferencia recibida, incluyendo la interferencia que pudiera provocar un a operacin indeseable. L O A P S E PRECAUCIN: Los cambios o modificaciones que no hayan sido expresamente aprobados por la parte responsable del cumplimiento podra anular el permiso del usuario para operar este equipo. NOTA: Este equipo ha sido probado y se encontr que cumple con los lmites establecidos para un dispositivo digital Clase B, de conformidad con la seccin 15 de las reglas de la FCC. Estos lmites estn diseados para ofrecer una proteccin razonable contra interferencias perjudiciales cuando el equipo se opera en una residencia. 12 13 Declaracin de interferencia de la FCC (cont.) Este equipo genera, usa y puede emitir energa de radio frecuencia, y si no se instala y usa de conformidad con las instrucciones podra provocar interferencia perjudicial en las comunicaciones de radio. Sin embargo, no se garantiza que dicha interferencia no ocurrir en una instalacin en especfica. Si este equipo ocasiona interferencia perjudicial a la recepcin de radio o televisin, lo cual se puede determinar apagando y encendiendo el equipo, se sugiere que el usuario trate de corregir la interferencia mediante una o ms de las siguientes medidas:

Colocar u orientar la antena receptora en otro lado. Aumentar la separacin entre el equipo y el receptor. Conectar el equipo a una salida o circuito distinto al que est conectado el receptor. Solicitar ayuda a su distribuidor o a un tcnico de radio o televisin con experiencia. El dispositivo ha sido evaluado para que cumpla con los requisitos generales de exposicin a RF. El dispositivo se puede usar en condiciones de exposicin porttil sin restricciones. E S P A O L 14 15 L O A P S E

Superior communications . 5027 Irwindale Ave.Suite Irwindale Ave California United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-11-41 To whom it may concer:

We, Superior communications ., hereby certify that the equipment for which authorization is sought

(FCC ID: YJW-10652PG) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www foc. gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 DO1 Sincerely, Signature George Chen VP Product Development Superior communications,

Superior communications . Add: 5027 Irwindale Ave.Suite Irwindale Ave California United States Date: 2023-11-1 FCC ID: YJW-10652PG Dear Sir/Madam, We, Superior communications . Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model:

Product name: 15W Wireless Charging Pad Model no.: 10652PG-VN, 10652PG, 10651PG, 10651PG-VN Sincerely, MV Name/Title; George Chen/VP Product Development

: Superior communications . 5027 Irwindale Ave Suite Irwindale Ave California United States 818-636-4985 626-608-9043 Gchen@scp4me.com

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2023-11-1>

Pursuant to Paragraphs 0.457 and 0.459 of the Commission's Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID Model name YJW-10652PG 10652PG-VN For the product stated above, we request that the following information be held confidential;

Long-Term Exhibits Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days Extemal Photos Internal Photos. Block Diagram Schematics Test Setup Photos:

User's Manual Parts List Tune Up moOooARRoo Operational Descriptions:

Dopooo0ol The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. George Chen/VP Product Development Superior communications 5027 Irwindale AveSuite Irwindale Ave California United States 818-636-4985 626-608-9043 Gchen@scp4me.com

Superior communications 5027 Irwindale Ave.Suite Inwindale Ave California United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-11-1 To whom it may concer:

We, the undersigned, hereby authorize Eurofins Product Service GmbH to act.on our behaffin all matters relating to applications for equipment authorization FCC ID: YJW-10652PG including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, MVM Name/Title: George Chen/VP Product Development Superior communications 5027 Irwindale Ave Suite Irwindale Ave California United States 818-636-4985 626-608-9043 Gchen@scp4me.com

Superior Communications. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 10/18/23 Superior Communications. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID:YJW-

10652PG):

Name and company of U.S. agent:

Tim Payne, FCC US Agent, LLC Physical U.S. address of agent:

3722 Illinois Avenue, Saint Charles, IL, 60174, USA FRN of U.S. agent:

0033402884 Email address of U.S. agent:

Support@FCCUSAgent.com FCC US Agent, LLC acknowledges their obligation to accept service of process on behalf of Superior Communications. Superior Communications. with the FRN 0019944727 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-

related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Chen George Manager Superior Communications. Signature Tim Payne Manager FCC US Agent, LLC 5 0 V

, U

) 7

) d

1 1 9

. 2 _ t n e g A _ S U

l e d o m

_ 8 4