ENFORCER 100LB/100CB Owner's Manual
(TA Appendix 2 UNDERSTANDING THE LED FLASHES A. Arming indicator Flashes quickly E. Tamper and triggered zone ID during the 30-second rearm to show Passive arming countdown. B. Door open indicator OFF when a hardwired door is opened during the 30-second rearm or passive arming Flashes one or more times after the alarm is disarmed to indicate which zone was triggered. RF reception indicator ON while any transmitter button is pressed. OWNER'S MANUAL countdown. G. Valet mode indicator Flashes slowly to indicate system is in valet mode. H. Anti-Carjack Rapid flashes to indicate the system is in the anti-
carjack mode. C. Armed indicator Flashes when the alarm is armed. D. Disarmed indicator OFF when the alarm is disarmed. NFORCER 100LB 100LB -4 100CB 100CB -4
(315 MHz) (433.92 MHz) Appendix 3 PROGRAMMABLE FEATURES Programmable features allow you to customize your alarm. Your dealer can program them when the alarm is installed. Permanent chirp delete Can permanently disable the sirens chirps. See page 8.
@ Passive/active arming Alarm is default at active arming. Press the | button to arm the alarm. R + C t II d In passive arming, the alarm arms itself when you turn the ignition OFF and close the last emote Controlie open door. Vehicle Security System
@ Current sensing Program the alarm for switch sensing only, or for both current and switch sensing. Alarm is default at current and switch sensing.
@ Ignition-controlled door lock and unlock Can be set to lock and/or unlock the doors automatically when the ignition is turned ON and/or OFF
@ Double Pulse Lock/Unlock Alarm default is set at single pulse lock/unlock. Some vehicles require a double pulse.
@ 0.5/3.5-sec. door lock/unlock time Alarm default is set at 0.5 sec.
@ Securelock (Automatic Locking) - If this feature has been enabled under the automatic arming mode, then the doors will automatically lock once the alarm arms. See page 8 Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate the device. Scr SECO-LARM U.S.A., INC. Page 12 SECO-LARM U.S.A., Inc. ENFORCER 100LB/1Q0CB Owner's Manual CONGRATULATIONS From the moment you purchased this ENFORCER Vehicle Security System, you become o part of the SECO-LARM family. You started taking advantage of over 34 years of advanced engineering. You joined a team of engineers, technicians, designers, and people like yourself who know how important protecting your car is. You discovered the SECO-LARM difference This difference is important because the ENFORCER is more than just an alarm. It's a complete security and convenience system. Its like having your personal security guard ond butler on call in your car, 24 hours doy. Keep in mind that the best security systems wi Therefore, the ENFORCER is designed for instal t work properly without careful installation, tion by your professional SECO-LARM dealer. He understands both his alarms and your needs, and will work hard fo ensure the ENFORCER does its job for you. Welcome to the family: SECO-LARM, your dealer, and you!
IMPORTANT This ENFORCER security system contains many innovative features and unique functions. Please read this Owners Manual car features. Some features may req:
in order to understand oll the addition of sensors or accessories not s olor
's se alarm. Please consult your professional SECO-LARM dealer NOTICE The information and specifications printed in this manual are current at the time of publication However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifi responsible for misprints or typographical errors. ions without notice. SECO-LARM is also not Copyright 2005 SECO-LARM* U.S.A., Inc. All rights reserved. This moterial may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM. This vehicle security system is protected by patents in the U.S.A., Great Britain, Germany, Hungary, Taiwan, China, Japon, and Korea. Other U.S.A FCC/IC COMPLIANCE THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATEON IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:(1}THIS DEVICE MAY NOT CAUSEHARMFUL INTERFERENCE AND (2}THIS DEVICE MUST ACCEPT ANY and international patents are pending FCC ID: K4E939T4Q INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Notice: The changes or modifications not expressly approved by the party responsible for complince could void the user's authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirement, no change to the antenna or the device is permitted. Any change to the antenne or the device could result in the device exceeding the RF exposure requirement and void user's authority to operatethe device. This device complies with Industry Canada licence-exempt RSS standard{s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Page 2 SECO-LARM U.S.A., Inc. ENFORCER 100LB/100CB Owner's Manual SR SST EES TT Appendix 1 UNDERSTANDING THE SIREN CHIRPS AND LIGHT FLASHES A. 1 chirp/flash:
@ When the I button is pressed, the alarm is armed.
@ When a door is closed, the alorm will orm in 30 seconds (passive arming]
@ 30 seconds after the ignition switch is turned OFF and all doors are closed lor delayed domelights turn OFF}, the alarm is armed {passive arming).
@ Successfully entered the valet mode B. 2 chirps/flashes:
@ When the II button is pressed, the alarm is disarmed.
@ Successfully exited the valet mode C. 3 chirps/flashes:
@ When pressing the | button to arm the alarm, indicates the alarm arms even though it is not set properly (door not closed, or broken switch, or domelight is still ON. NOTE: If the delayed domelights are ON when the | button is pressed, the siren will chirp 3 times. This gives the impression that the door is open when it may really be closed.
@ When pressing the I button followed by the III button, indicates sensor is bypassed Completed emergency disarm.
@ Pre-intrusion warns potential thieves or vandals who trigger the first stage of any dual-stage sensor that is connected to the alarm D. 4 flashes only:
@ When the I or Il button is pressed during the valet mode. E. 2 Chirps/ 7 flashes
@ When pressing the Il button to disarm the alarm, indicates the alarm was triggered NOTE The chirps for orm, disarm, zone bypass, sensor bypass, emergency disarm, valet, ond tamper con be deleted. (Ask your dealer.) Page 11 ENFORCER 100LB/100CB Owner's Manual TAMPER INDICATORS & TRIGGER ZONE ID IFyour clorm was triggered when you were away, the siren will chirp two times and the 4 floshesA door wos parking lights flash seven times when you opened. disarm your olarm. The LED flashes in quick 5 flashes The hood cycles to show where the car was violated as or trunk was opened, follows: 6 flashes Current sensing was
@ 1 flash The ignition was turned on. triggered. 2 floshes The olarm wos triggered vio These memory flashes aulomatically reset ponic. when the ignifion is turned ON. 3 flashes The shock sensor or other odd-on sensor was Iniggered. IGNITION-CONTROLLED POWER DOOR LOCKS Your alarm can be programmed for ignition-controlled operotion (doors lock when you turn the ignition ON, and/or unlock when the ignition is turned OFF). Consult your dealer. OTHER FEATURES
* Starter disable With this optionol fecture, while your alarm is ormed, your car will not start, even if a thief has your keys,
* Dual-power protection (DPP) Helps keep your alarm powered even if a thief cuts the clorms main power line. (Optional ~
ask your decler.}
* Double Pulse Lock/Unlock For vehicles that requires two pulse signals to arm/lock &
disarm/untock. Page 10 SECO-LARM U.S.A., Inc. ENFORCER 1001LB/10GCB Owner's Manual LST |
TABLE OF CONTENTS Transmitter Functions ......cce--enseseerecreeceessseee 3 Chirp Delete (Silent arm/disarm) 8 ENFORCER 100LB or ENFORCER 100CB?....3 Emergency Call for Help (Ponic) ... 8
-- 4 Powar Door Locks ii (8
.. 4 Anti-Carjock Protection (optional) ai?
Sensor Bypass ..... 5 Tamper Indicator & Trigger Zone ID _......11 Zone BYpOSs ....-.-ereeme - 5 Ignition-Controlled Power Door Lock .......... 10 2nd Channel Output. - 5 Other Features sevovuerseeneeee 10 Total Protection .... . 6 Appendix 1 Understanding the Siren Chirps Disarming ....... a Be Light Flashes ........cssenenuessssvsersseesessnsn VW Emergency Disarm .. 6 Appendix 2 Understonding the LED GODOT escesscssssccrisa cose wa F Arse sn eesscssccssessceovtnnrsnnernentsseenransee 12 Patented Stoy-safe Disarm .. 7 Appendix 3 Progrommoble Features .... 12 Dual-stage Shock Sensor ........ 7 TRANSMITTER FUNCTIONS 1. Press the I button to: 4, Press the IV button to:
Arm the alarm. @ Turn the siren ON in an emergency. Lock power door locks.
@ Reset the clarm. Lock:
Bypass an open zone. a Auxiliary 2. Press the IW button to:
@ Disarm the alarm. Unlock power door locks. 2. Press the Ill button to:
Operate channel 2 (such os popping the ga trunk or rolling up the windows}.
@ Silently orm or disarm the olorm,
@ Byposs the olorm's sensors. ENFORCER 100LB OR ENFORCER 100CB?
Unlock 7 Panic oe These two models offer the same convenience ond protection features and have the some operation, The only difference is thot the ENFORCER 100CEB features CODEBUMP anti-codehopping technology. This means that the iransmitters code changes each lime you press one of its buttons to prevent thieves from using 0 code-grabbing device to copy the code. Page 3 ENFORCER 100LB/100CB Owner's Manual ARMING There are two different ways to arm your alarm. Tell your dealer which is best for you:
Active Arming Turn your ignition OFF. Close all the doors. Then press the I button. If the siren chirps and parking lights flash once, the alarm is fully armed and the doors lock. If the siren chirps 3 times, the alarm is either waiting for the vehicle's delayed domelights to turn OFF (if your vehicle is so equipped), or it is telling you that one of the alarm's zones (0 door, or the hood or trunk) is either open or is not functioning properly. (See ZONE BYPASS, page 5). Also, check to make sure your car's domelight switch was not left in the ON position. These chirps can be programmed off. See page 11. Q Passive arming Turn your ignition OFF, and open a door to exit the car. When the last door is closed
(and the domelight turns OFF, if your car has delayed domelights), the siren chirps and parking lights flash once. The LED flashes quickly during the 30-second arming countdown, after which the siren chirps and parking lights flash once more to confirm the alarm is completely armed. If you wish, you can open a door during the arming countdown, and keep it open for as long as needed. The LED turns OFF while the door is opened. Close the last door, and the siren will chirp and parking lights flash once to show the 30-second arming countdown has started again. The LED will also begin to flash quickly. If you close the last open door, and the siren does not chirp and parking lights do not flash, you know that one or more openings are not closed properly. This is SECO-LARMs patented Quick and Quiet Testing (Q.Q.T.), and it prevents you from thinking your alarm is armed when i may not be. In this case, double-check that all the doors, as well as the hood and trunk, are closed properly, and that your vehicles domelights are OFF. If you cannot locate the problem, but need to arm the alarm, then press the I button to immediately arm the alarm and bypass whatever zone is open (see ZONE BYPASS, page 5). NOTE Under passive arming, you can force your alarm to arm immediately any time during the 30-second arming countdown by pressing the I button. NOTE Make sure your cars domelight switch is not in the ON position when you arm your alarm either actively or passively, otherwise the alarm may not arm properly if the domelight switch is left ON. NOTE There are references to opening or closing a door throughout this manual. Door also includes your hood and trunk, if they are protected. Consult your dealer. ARMED When the 30-sec. arming countdown ends, or when the I button is pressed to arm the alarm, the siren chirps and parking lights flash once, Page 4 and the LED starts flashing to show the alarm is armed. SECO-LARM U.S.A., Inc. ENFORCER 100LB/100CB Owner's Manual ANTI-CARJACK PROTECTION (optional) A. Enabling the ANTI-CARJACK function:
If the ANTI-CARJACK toggle switch is not installed, you cannot use the ANTI-CARJACK function (please ask your dealer). To enable the ANTI-CARJACK function, put the ANTI CARJACK toggle switch to the ON position. If the ANTI-CARJACK toggle switch is OFF, the ANTI-CARJACK function cannot be entered. Once the ANTI-CARJACK function is enabled, you can disable it by turning the ANTI-CARJACK toggle switch OFF However, this must be done before you turn the ignition ON. B. Stages of the ANTI-CARJACK mode:
1. Stage 1 a. ANTI-CARJACK is triggered someone opens and closes a door while the ignition is ON. Once ANTI-CARJACK is triggered, turning OFF the ANTI-CARJACK toggle switch will have no affect. At this point, Stage 1 begins. Stage 1 lasts for up to 30 seconds. b. During the 30 seconds, the LED flashes
| ae c. Pressing the VEL switch one time during the 30 seconds exits ANTI-CARJACK. Once ANTI-CARJACK is exited, the LED turns OFF. d. If the ignition is switched OFF at any time during the EP 30 seconds without first :
pressing the VEL switch, Stage 1s 30-second countdown will pause, but ANTI-CARJACK will not exit. The LED will turn OFF. The next time the ignition is turned ON, Stage 1s 30-
second countdown will pick up where it left off. 2. Stage 2 a. Once Stage 1 ends, Stage 2 begins. Stage 2 also lasts for up to 30 seconds. b. While in Stage 2, the LED continues to flash rapidly, the parking lights flash, and the EP siren continuously chirps. c. Pressing the VEL switch at any time during this stage exits ANTI-
CARJACK provided the ignition is still ON. (If the ignition is turned OFF before pressing the VEL switch, below.) Once ANTI-CARJACK is exited, the lights stop flashing, the siren stops chirping, and the LED turns OFF. The alarm can now be used as normal. 3. Stage 3 a. Once Stage 2 ends, Stage 3 immediately ae begins. b. While in Stage 3, the LED remains rapidly flashing, and the parking lights continue to flash. However, the siren sound changes from chirping to a full blast (sound continuously). The ghts flash and the siren sounds until the emergency disarm procedure is performed or until 30 seconds after the ignition is turned OFF c. The starter disable output is engaged. This means that turning the ignition EP OFF or pressing the e VEL switch one time will have no effect. The emergency disarm procedure must be performed in order to exit ANTI-CARJACK and Page 9 ENFORCER 100LB8/100CB Owner's Manual CHIRP DELETE (silent arm/disarm) There are times, especially af night, when you may not want t6 hear the siren chirps. There are 2 ways jo delete chirps:
A. One-time delete Jus! press the Ill button any time before you need the chirps deleted. For instance, press the II} button before you press the
| button to orm the alarm, and the chirps will not sound, but the parking lights will chirps ore resiored the nex! time you press any transmitter button. BL Permonent delcle Your deoler can program your alarm to delete ihe chirps on a permanent rs 5 NOTE Either method deletes the orm, disorm, pre-
disarm, valet, and tamper chirps. However, they do basis. intrusion, zone bypass, sensor bypass, emergency not affect the floshing parking lights. Silent Arm ay EMERGENCY CALL FOR HELP (Panic) To trigger the olorm in an emergency, press the IV button for 2 seconds. The siren sounds and the parking lights flash for about 30 seconds. The clorm and door lock/unlock status do not chonge. Stop the siren and the parking lights any time by pressing ony of the four buttons. Note;
1, The olorm will be in the armed mode ond the doors will lock if the I buttan is used to exit the panic mode. 2. The clarm will be in the disarmed mode ond the doors will unlock if the H button is used to exit panic mode. 3. The clorm will be in the disarmed mode, the doors will lock, and channel 2 output will be activated if the II button is used to exit panic mode 4. The alarm and the door locks will return 40 their origina! mode if the IV button is used to exit panic mode. POWER DOOR LOCKS Wilh this optional feature, your alorm can eulomatically lock the doors when the I bution is pressed to arm the olorm and unlock the doors when the Il bution is pressed to disarm the alarm. For exira security, they lock automatically if the clorm is triggered.
{Exception See EMERGENCY CALL FOR HELP obove) Your ofarm con also be progrommed for ignition-contrallied operation, The doors can be set to outomoticolly lock when you turn the ignition ON, ond unlock when you tum the ignition OFF. NOTE Under possive orming, ond when the SecureLock function is enabled, the doors automatically lock cher the 30-second exit delay is aver and the alarm arms. Page 8 SECO-LARM U.S.A., Inc. ENFORCER 10018B/100C8 Owner's Manual SENSOR BYPASS This is useful if you know, based on experience, thot your shock sensor {or other add-on sensors) will false triggers, such os when you park near o construction site. Should you wish to bypass your alarm's sensors, first press the I bution to arm the olorm {even if the alarm is set for passive arming). The siren chirps ond the parking lights flash once {three times if a zone is bypassed) to confirm armed. Within three seconds, press the Ill button. The siren chirps three times ond the parking lights flosh three times to confirm sensors ore bypassed, The sensors are ovtomatically restored the ned time the Il button is pressed. NOTE The chirps to confirm sensor bypass will not sound if chirp delete is engaged. However, the parking lights will still flash three times. See CHIRP DELETE, page 8. ZONE BYPASS When you press the I button to arm the olorm, and the alarm responds with three chirps and three porking light! flashes, there ore two possibilities:
A. Delayed domelights Delayed domelights. do not immediately turn OFF when you close your cor door. This is normal. The alarm should protect oll doors once the domelights turn OFF B. Azone was bypossed In other words, the alorm has ormed, but a door may not be protected (cither because it is open, or because its pin switch is broke:
bypassed door is loter closed, restored. If your alarm indicates a bypassed zone, find the cause a3 soon as possible to ensure your vehicle is completely protected. For instance, if your driver's door is not properly closed when you arm your alarm, a thief may be able fo open any door without setting off the alarm. NOTE The chirps to confirm zone bypass will not sound if chirp delete is engoged. However, the parking lights will still flash three times. See CHIRP DELETE, page 8. 2nd CHANNEL OUTPUT Your transmitier hos on extra channel to control optional accessories. 2nd channel is commonly used to pop the irunk. To use, press the Ill bution for two seconds, eilher while the ignition is ON and any door is opened, or while the ignition is OFF. The clorm will disorr prevent the siren from sour
(NOTE IF no doors ere connected directly to your alarm, the 2nd chonnel will not operate with the ignition ON. Ask your deoler for details.) Page 5 ENFORCER 100LB/1Q0Q0CB Owner's Manual SOSA SIL EET TS OI TOTAL PROTECTION While your alarm is armed, your car is protected in the following ways:
@ Potential thieves or vandals will be warned by the flashing LED.
@ fa thief opens a door, the alarm immediately sounds the siren and flashes the parking lights for 30 seconds. If the opened door is not closed and current sensing has not been selected, the siren and lights will trigger up to four 30-second cycles, after which the alarm will rearm.
@ Turning the ignition key ON will trigger the alarm for 30 seconds.
@ The starter disable prevents the car from being started.
@ ANTI-CARJACK (optional) is triggered if someone opens and closes a door while the ignition is ON.
@ Ifthe shock sensor detects light taps on the car, it will trigger the pre-intrusion alert (the siren chirps five times and the parking lights flash five times) to warn potential thieves and vandals. However, if it detects a strong shock to the car, such as shock caused by prying the trunk open, it w trigger the alarm for 30 seconds. (See DUAL-STAGE SHOCK SENSOR, page 7)
@ Optional SECO-LARM shock, motion, glass-break, and microwave sensors wi offer your alarm additional protection. Ask your SECO-LARM dealer. DISARMING To disarm the alarm, press the Il button. The siren chirps twice, the parking lights flash twice, and the LED turns OFF. What happens next depends on how your alarm is set (ask your dealer):
Q Alarm set for active arming with Secure Lock OFF The alarm is now completely disarmed. Q Alarm set for active arming with Secure Lock ON The system will automatically rearm and relock the doors 30 seconds later unless a door is opened during this time. This prevents accidental disarming. During this 30-second period, the LED flashes quickly. Q Alarm set for passive arming The system will automatically rearm itself 30 seconds later. If a door is opened, the system temporarily disarms. Closing the open door will again cause the system to enter the 30-second rearm period. NOTE If set for Secure Lock, the doors jock when the system rearms. Otherwise, the doors do not automatically relock. EMERGENCY DISARM If you lose your transmitter, you can disarm your alarm with the ignition key and the VEL switch. While your alarm is either armed or triggered, turn the ignition switch ON. Within 15 seconds, press and release the VEL switch three times. The siren and the flashing lights stop if the alarm was triggered, and then chirp and flash two times. (Ask your dealer where the VEL button is hidden.) NOTE If you use emergency disarm, just turn the ignition OFF and close the doors when you leave your car, and the alarm arms automatically. Next fime you open a door, you will have 10 seconds of quiet to turn the ignition switch ON and press the VEL button three times to disarm the alarm. This feature is cancelled next time you use your transmitter to arm or disarm your alarm. Page 6 SECO-LARM U.S.A., Inc. ENFORCER 100LB/100CB Owner's Manual SD AL ENTE EET TIPE TCT VALET Sometimes you may not wish your alarm to arm when you leave your vehicle. (For stance, if you leave your car with a valet attendant, you may not want to teach him how the alarm operates.) If your alarm is set for active (manual) arming, this is easy dont press the I button, and the alarm will not arm. However, if your alarm is set to arm passively, use the valet mode to prevent it from arming. To enter valet, first disarm the alarm and turn the ignition ON. Within 15 seconds, press and release the VEL switch three times. The alarm is now in the valet mode. The siren chirps and the parking lights flash once to confirm. To exit valet, just turn the ignition ON and, within 15 seconds, press and release the VEL switch three times. The siren chirps twice and the parking lights flash twice to confirm that valet is exited and the alarm is now disarmed. If you press the I or Il while the alarm i valet, the doors will lock or unlock, and the parking lights will flash four times. The alarm's emergency call for help and 2nd channel output operate normally. PATENTED STAY-SAFE DISARM Any time your alarm is triggered (the siren is sounding and the parking lights are flashing), press the I button of the remote once to shut the siren and flashing parking lights OFF while the alarm stays completely armed. DUAL-STAGE SHOCK SENSOR Your alarm includes a patented dual-stage shock sensor. The first stage (pre-intrusion alert) warns thieves the alarm is armed. For instance, the alarm will chirp three times and the parking lights will flash three times if the sensor detects a light bump to the vehicle. However, if a thief attacks the car with sufficient force, the alarm trigger. (Your dealer can make the shock sensor more or less sensitive to attack, depending on your vehicle.) NOTE The shock sensor (and other add-on sensors, and current sensing) will not trigger the alarm until 4 seconds after the alarm is armed. Page 7