N/A Sensor Speaker 433.92 MHz Up to 22ft (7m) Standby Active Up to 328ft (100m)*
ENFORCER Wireless Entry Alert System Introduction:
The ENFORCER Wireless Entry Alert System is a self-contained easy-to-install alert system for commercial or home applications. Each set contains a reflective photoelectric beam sensor that, when tripped, communicates wirelessly with a speaker installed up to 328ft (100m) away*. An additional speaker may be installed to alert more than one area on the property and an optional solar charger may be installed with the sensor for even more convenience. Specifications:
Sensing range Wireless range Operating frequency Operating voltage Current draw Power input Light source Operating temperature Volume Alarm time range Speaker output IP Rating Dimensions
*Range may vary greatly depending on the installation and operating environment. Parts List:
1x Sensor 1x Speaker 1x Reflector 2x Power adapters 1x Small screwdriver Overview:
1x Mode adjustment pin 1x Sensor mounting bracket 1x Reflector mounting bracket 2x Bolts (Sensor) 2x Bolts (Reflector) 4x Nuts 5x Mounting screws 1x Screw anchor 1x Manual 31/4x215/16x19/16
(83x75x40 mm) 31/4x29/16x11/2
(82x66x38 mm) Chime/Off/Alarm (selectable) 32~122 F (0~50 C) 3~30 s (Adjustable) N/A N/A N/A IP55 2.5mm DC Jack 25mA 100mA 5mA 20mA 0~90 dB IR LED 12VDC N/A N/A Sensor Reflector 11/2
(38mm) 29/16
(66mm) 19/16
(40mm) Alert tone selection 21/16
(52mm) 3/8
(9mm) 31/4
(82mm) Alignment LED 23/8
(61mm) 31/4
(83mm) Speaker 215/16
(75mm) 2.5mm DC Jack Cable length: 97/8 (250mm) Optional Accessories:
Additional Wireless Speaker E-931ACC-SFQ Solar Charger for Sensor E-931ACC-SPQ 2 Counter output Timer Volume Mode button 2.5mm DC Plug Digital Counter E-931ACC-CQ Hood for Square and Round Reflectors E-931ACC-HR1Q Replacement Square Reflector E-931ACC-R2Q 3 Round Reflector E-931ACC-RC1Q SECO-LARM U.S.A., Inc. ENFORCER Wireless Entry Alert System Solar Charger. Installation:
1. Install the reflector and sensor so they face each other about 2ft (61cm) off the ground. 2. Install the speaker within 328ft (100m) of the sensor. 3. Connect an included power adapter to the sensor. If optional solar charger is used, see pg. 4, Installing the Optional 4. Connect an included power adapter to the speaker. 5. To find the correct alignment, slowly adjust the angles of the sensor and reflector. NOTE: Alignment is correct when the red LED turns ON. Mounting:
Sensor Reflector Speaker included bolts and nuts. 1. Drill included screw into wall. 2. Hang speaker on screw. increases the volume; counter-clockwise decreases the volume. clockwise will set the timer for 30 seconds; turning all the way counter-clockwise will set the timer for three seconds. 1. Attach the sensor or reflector to their respective brackets by using the 2. Mount the bracket to the wall using two of the included mounting screws. Programming the Speaker:
1. Choose between Chime, Alarm, and Off using the alert tone selection switch on the side of the speaker. 2. Adjust the volume by using the included Phillips screwdriver to turn the volume adjustment screw. Turning clockwise 3. Adjust the timer by using the included Phillips screwdriver to turn the timer adjustment screw. Turning all the way NOTE: Timer mode only applies if Alarm is chosen as the alert tone. Pairing the Sensor and Optional Additional Speakers (E-931ACC-SFQ):
Use one of the two methods below to pair the optional additional speaker with the sensor. NOTE: The speaker included with the Wireless Entry Alert System is pre-paired with the sensor. Method 1:
1. Use the included mode adjustment Clearing Memory:
1. Use the included mode adjustment pin to press and hold the mode switch until you hear a long beep from speaker. This means the speaker is in the learning mode. 2. Trigger the sensor by breaking the beam. The speaker will beep once. 3. After 10 seconds, the speaker will make one long beep indicating successful pairing. Method 2:
1. Remove the side panel of the sensor with the included small Phillips screwdriver. 2. Perform the point 1 of Method 1 and then press sensors learning button once. The speaker will beep once. 3. After 10 seconds, the speaker will make one long beep indicating successful pairing. pin to press and hold the mode switch until you hear a long beep and two short beeps after five seconds. 2. Release the mode button and the memory has been cleared. Learning button IMPORTANT: When pairing additional speaker, release the mode switch immediately after two seconds and hearing the long beep. Pressing the mode switch for more than five seconds will delete the memory. Connecting the Optional Counter (E-931ACC-CQ):
1. Connect the plug from the counter to the counter output jack of the speaker. 2. Test the counter. Each time the beam is broken, the counter should 3. Manually add or subtract 1 by pressing the + or - buttons 4. Reset the counter by pressing RESET. SECO-LARM U.S.A., Inc. automatically increase by 1. 3 The Federal Communication Commission Statement This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures: -
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced Radio/TV technician for help. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that change or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
This device may not cause harmful interference and This device must accept any interference received, including interference that may cause undesired 1 2 operation. The antenna used for this transmitter must not be collocated or operation in conjunction with any other antenna or transmitter. Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate the device.