Supertek Co., Limited EVJ-WN1_V1.0 WIFI CAMERA MODULE with GC0308 image sensor A1.0 Model No. Description Customer Name Version Camera Module Technical Data Sheet Supertek Part No. EVJ-WN1_V1.0 Revision1.0 2019/07/02 Prepared By Checked By Approved By Jingxu Xu David Liao Date 2019/07/02 Date 2019/07/02 Date 2019/07/02 Customer Customer Signature and Seal Data 1 Model No. Description Customer Name Version Supertek Co., Limited EVJ-WN1_V1.0 WIFI CAMERA MODULE with GC0308 image sensor A1.0 Revision History Revision Date Prepared By Description A1.0 2019/07/02 Jingxu Xu First Release Approved by Checked by Edited by 2 Supertek Co., Limited EVJ-WN1_V1.0 WIFI CAMERA MODULE with GC0308 image sensor A1.0 Model No. Description Customer Name Version Contents 1. WIFI Camera Specification 2. WIFI Chipset General Description 2.1 General Description 2.2 Applications 2.3 Features 2.4 Key Specification 2.5 Block Diagram 2.6 Pin Connector Descriptions 2.7 Schematic 3. MCU Information 3.1 Outline 3.2 Features 3.3 Pin Definition 3.3.1 Packages 3.3.2 Pin Assignment 3.3.3 Pin Description 4. Schematic of WIFI chipset and MCU 5. USB Camera Information 5.1 Image sensor GC0308 General Desciption 5.2 Image sensor GC0308 General 5.3 Mechanical drawing of USB camera 6. Drawing of SHWN8189WIFI Camera Module 7. Environmental and Reliability Specification 8. Packaging Information The default label contents Packing SPEC 9. Precaution Storage and operating conditions Transportation and Handling 8.1 8.2 9.1 9.2 3 Supertek Co., Limited 1. WIFI Camera Specification:
SPECIFICATION Main material Sensor: GC0308, USB chip: SPCA2072A MCU: AX3268-UM-001, WIFI chip: BL-M8189FS3 VGA(640*480) DSP SPCA2072A can only support VGA Color 30fps USB connector (battery for option as well) Controlled by MCU, the setting way can be met by your requirement On the smart device SSID can change, manually connect to WIFI camera Different SDK for Iphone, Andriod and Windows Resolution Gray scale Frame rate Power Light Indicator Data save SSID name SDK Working mode-AP WIFI camera will give out the hotspot for the smart device to connect WIFI camera size Same as your size: 49.6*35mm 2. WIFI CHIPSET INFORMATION;
2.1 General Description 4 Supertek Co., Limited 2.2 Applications 2.3 Features 2.4 Key Specification 5 Supertek Co., Limited 2.5 Block Diagram crystal 26MHZ 6 Supertek Co., Limited 2.6 Pin Connector Descriptions:
7 Supertek Co., Limited 2.7 Schematic 3. MCU INFORMATION 3.1 Outline 3.2 Features 8 Supertek Co., Limited 3.3 Pin Definition 3.3.1 Packages LQFP48 3.3.2 Pin Assignment 3.3.3 Pin Description 9 Supertek Co., Limited 10 Supertek Co., Limited Note: PIN46 is the same as PIN52, PIN46 can be floating. 11 Supertek Co., Limited 4. Schematic of WIFI chipset and MCU:
5. USB Camera 5.1 Image sensor GC0308 General Desciption 12 Supertek Co., Limited 5.2 Image Sensor GC0308 General 5.3 Schematic Drawing of USB camera 13 Supertek Co., Limited 6. Drawing of SHWN8189WIFI Camera Module 7. Environmental and Reliability Specification NO Test name Condition Sample size Judgement 1 2 3 4 5 6 High Temperature storage Low Temperature storage 80+/-2 24H
-40+/-2 48H Humidity storage 60, 95%[RH] 72H
-40(0.5H)~80 Thermal shock
(0.5H)/cycle 30Hz,0.38mm&55 Hz,0.19mm, XYZ ion, direction,0.5H/direct 1m/one direction. 1time/direction, total 6 direction Vibration test Drop test 1, no image change before and after 2, no transformation and broken mechanically 3, no focus changing of lens 4, vision inspection OK 5pcs 5pcs 5pcs 5pcs 10pcs 10pcs 14 Supertek Co., Limited 5 6 Vibration test Drop test 32cycle 30Hz,0.38mm&55Hz,0.19mm, XYZ direction,0.5H/direction, 1m/one direction. 1time/direction, total 6 direction 10PCS 10PCS mechanically 3. No focus changing of lens 4.Visual Inspection OK 8. Packaging Information 8.1 The default label contents:
SupplierSupertek Customer Part Number: XXXXX Supertek Part Number: XXXX Quantity: XXXXX Country Of Origin: CN Lot Number: XXXXXX Note: Supertek has the right to update the label form and contents and will inform the customers. 8.2 Packing SPEC Modules are placed into a tray. Insert tray into a ESD protect bag. All the finished goods are placed in box. 9. Precautions 9.1 storage and operating conditions To keep the product and packaging material in good condition, care must be taken to control temperature and humidity in the storage area. Recommended conditions:
Moisture proof ScaleMSL3 exposure 30/60%RH,168 hours floor life Ambient temperature: 226 15 Supertek Co., Limited SHWN8189WIFI WIFI CAMERA MODULE with GC0308 image sensor Appletec Ltd A1.0 Model No. Description Customer Name Version Humidity: 2060%RH No rapid change on temperature and humidity Bake condition: If the modules exposure under high temperature and humidity surroundingsthey must be put in the dry case which humidity 10RH more than five times of exposed time to recover the modules floor life. The products listed in this catalog are not designed for use under the following conditions. Storage and/or usage under following conditions are prohibited. Exposure to corrosive gas such as chlorine, hydrogen sulfide, ammonia, sulfur dioxide, nitrogen oxide, etc. Exposure to direct sunlight. Exposure to dust. Exposure to excessive moisture or wet locations. Exposure to salt water or sea breezes. Exposure to strong static electricity or electromagnetic waves. 9.2 Transportation and Handling Minimize any mechanical vibration or shock and avoid dropping of the product during transportation or dropping the product that contains the substrate. Since the application of static electricity or over voltage may cause defect in the product or deterioration of its reliability, caution must be taken against exposure to any static electricity generated by electrified items such as workbenches, soldering irons, tools, carrying containers, etc. Caution shall be taken to avoid overstress to the product. 16 FCC Statement FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Integral PCB antenna;Antenna gain: 1.46 dBi This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. We will retain control over the final installation of the modular such that compliance of the end product is assured. In such cases, an operating condition on the limit modular approval for the module must be only approved for use when installed in devices produced by a specific manufacturer. If any hardware modify or RF control software modify will be made by host manufacturer,C2PC or new certificate should be apply to get approval,if those change and modification made by host manufacturer not expressly approved by the party responsible for compliance ,then it is illegal. FCC Radiation Exposure Statement The modular can be installed or integrated in mobile or fix devices only. This modular cannot be installed in any portable device. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2AUJJ-EVJ-WN1 Or Contains FCC ID: 2AUJJ-EVJ-WN1 When the module is installed inside another device, the user manual of the host must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any company of the host device which install this modular with limit modular approval should perform the test of radiated & conducted emission and spurious emission,etc. according to FCC part 15C : 15.247 and 15.209 &
15.207 ,15B Class B requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209 & 15.207 ,15B Class B requirementthen the host can be sold legally.