FCC ID: ZQXAS-7100ULS LCD KVM

LCD KVM SWITCH User Manual LCD KVM Console User Manual Statement United States Federal Communications Commission Interference Statement This product has been tested and found to comply with FCC regulations Class B (Class B) digital device and FCC specifications Details of Section 15.These specifications are intended to be used in a commercial environment without harmful interference and to provide for the protection of regulated equipment. This equipment generates, and can radiate radio, so if you do not have to install and use as specified in this manual, may cause interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment is turned on or off causing interference to radio and television reception, the user should try the following to reduce the interference. Change the direction and move the receiving antenna. Increase the distance between the equipment and the receiver. Connect the device to the circuit outlet (not the interface to which the receiver is connected) Consult the dealer and an experienced radio / TV technician for help. FCC Warning: change and modify non-qualified party which is responsible for the equipment is made to void the user's authority to operate the equipment. CE WARNING: This product is a Class B product. In a domestic environment, this product may cause radio interference, and the user may need to take appropriate precautions. The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RoHS This product is RoHS compliant. 57 User Precautions LCD KVM Console User Manual The manufacturer has the right to modify and alter the information, documentation and specifications contained in this manual without prior notice. Manufactures makes no warranty, express, implied or statutory, disclaims or specifically disclaims it's possibility of sale and applicability for a particular purpose. The same applies to any sold and authorized manufacturer's software described in this manual. If the Software Program is found to be defective after purchase, the purchaser (and any non-manufacturer, its distributor or its purchaser) will be responsible for all necessary service, repair and any incidental or consequential damages resulting from the Software defect. The manufacturer is not responsible for any unauthorized interference with the radio or television caused by this equipment. The user must correct the interference personally. The manufacturer will not be liable for any damage resulting from incorrect selection of the operating voltage before operation. Please be sure that the voltage has been set correctly before use. A typical LCD (liquid crystal display) has millions of pixels. A dead pixel is a defective pixel that does not display the correct color. On the screen, it usually looks like a tiny black or white dot, which can also be any other color. In the manufacturing process, even if a pixel on the tiny dust particles, or in the course of a slight impact during transport, may have a dead pixel. In the ISO 13406-2 specification, four categories of acceptable screen dead pixels are defined: the first is the best product, and the fourth is the worst. Almost all manufacturers use the second level as a guarantee of the product, allowing a certain number of dead pixels exist, such as more than the tolerance will change the screen. Since the manufacturer is of the opinion that this screen is permitted by the ISO specification, we are not responsible for the replacement or warranty of the TFT LCD panel. 57 LCD KVM Console User Manual Product Model Description Single-rail Series Configuration instructions VGA Single portKVM,17inch 4:3 LED Monitor, No OSD Menu, Can be cascaded DVI Single port KVM,17inch4:3 LCD Monitor, No OSD Menu VGA Single portKVM,17inch4:3 LCD Monitor, No OSD Menu, Can be cascaded, IP Remote Control VGA Single portKVM,19inch4:3 LCD Monitor, No OSD Menu, Can be cascaded DVI Single portKVM,19inch4:3 LCD Monitor, No OSD Menu VGA Single portKVM,19inch4:3 LCD Monitor, No OSD Menu, Can be cascaded, IP Remote Control VGA 4Ports KVM ,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 4Ports KVM ,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded DVI 4Ports KVM ,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure VGA 4Ports KVM ,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 4Ports KVM ,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 4Ports KVM ,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 4Ports KVM ,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded DVI 4Ports KVM ,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure VGA 4Ports KVM ,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 8Ports KVM ,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 8Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded DVI 8Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, VGA 8Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 8Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 8Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 8Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded DVI 8Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, VGA 8Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 8Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 16Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 16Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded VGA 16Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 16Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, AS-7100ULS AS-7100DLS AI-7100ULS AS-9100ULS AS-9100DLS AI-9100ULS AS-7104ULS AS-7104TLS AS-7104DLS AI-7104ULS AI-7104TLS AS-9104ULS AS-9104TLS AS-9104DLS AI-9104ULS AS-7108ULS AS-7108TLS AS-7108DLS AI-7108ULS AI-7108TLS AS-9108ULS AS-9108TLS AS-9108DLS AI-9108ULS AI-9108TLS AS-7116ULS AS-7116TLS AI-7116ULS AI-7116TLS 57 LCD KVM Console User Manual AS-9116ULS AS-9116TLS AI-9116ULS AI-9116TLS Remote Control VGA 16Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 16Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded VGA 16Ports KVM,19inch4:3 LCD Monitor, SD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 16Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control Dual-rail Series Model AS-7100ULD AI-7100ULD AS-9100ULD AI-9100ULD AS-7104ULD AS-7104TLD AI-7104ULD AI-7104TLD AS-9104ULD AS-9104TLD AI-9104ULD AI-9104TLD AS-7108ULD AS-7108TLD AI-7108ULD AI-7108TLD AS-9108ULD AS-9108TLD AI-9108ULD AI-9108TLD AS-7116ULD 57 Configuration instructions VGA Single port VM ,17inch4:3 LCD Monitor, No OSD menu, Demountable Structure, Can be cascaded VGA ingle port KVM ,17inch4:3 LCD Monitor, No OSD menu, Demountable Structure, Can be cascaded, IP Remote Control VGA Single port KVM ,19inch4:3 LCD Monitor, No OSD menu, Demountable Structure, Can be cascaded VGA Single port KVM ,19inch4:3 LCD Monitor, No OSD menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 4Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 4Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded VGA 4Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT54Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 4Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 4Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded VGA 4Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 4Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 8Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 8Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded VGA 8Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 8Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 8Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 8Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded VGA 8Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 8Ports KVM,19inch4:3 LCD Monitor ,OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 16Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded LCD KVM Console User Manual AS-7116TLD AI-7116ULD AI-7116TLD AS-9116ULD AS-9116TLD AI-9116ULD AI-9116TLD CAT5 16Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded VGA 16Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 16Ports KVM,17inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control VGA 16Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded CAT5 16Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded VGA 16Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control CAT5 16Ports KVM,19inch4:3 LCD Monitor, OSD Menu, Demountable Structure, Can be cascaded, IP Remote Control 57 Package Contents LCD KVM Console User Manual The LCD KVM switch package includes the following:

Name Quantity/unit Description LCD KVM Console KVM Cables Power Power Cord InstructionsCD Quick Installation Guide Mounting brackets Lock ear Install the screw kit 1/pc N/pc 1/pc 1/pc 1/pc 1/pc 2/pcs 2/pcs 1/pc The LCD kit products Cables quantities according to the standard Port that selected If it is built-in power supply products, power built-in. Standard 1.8 m power cord Using electronic data CD manual Quick installation manual LCD KMV Single mounting bracket LCD KVM fix the rear panel Screw the mounting bracket Check that all parts are present and that they are not damaged in transit. If you encounter problems, contact your dealer. To prevent damage to the machine or equipment connected to the machine, please read this manual carefully and follow the instructions to install and operate it.

* There may be additional product features since the publication of this manual. Please visit our website to download the latest version of the user's manual. 57 Contents LCD KVM Console User Manual User Precautions........................................................................................................................................................................... 3 Product Model Description...........................................................................................................................................................4 Single Slide Series................................................................................................................................................................4 Dual-rail Series..................................................................................................................................................................... 5 Package Contents..........................................................................................................................................................................7 About this manual.......................................................................................................................................................................10 Description of Terms.................................................................................................................................................................. 11 Chapter 1.....................................................................................................................................................................................12 Introduction.................................................................................................................................................................................12 Production Introduction......................................................................................................................................................12 Product Features................................................................................................................................................................. 14 Hardware Requirements..................................................................................................................................................... 15 Console....................................................................................................................................................................... 15 Computer.................................................................................................................................................................... 15 Cables......................................................................................................................................................................... 15 Operation System....................................................................................................................................................... 18 Part......................................................................................................................................................................................19 Front View..................................................................................................................................................................19 Rear View...................................................................................................................................................................20 Front view of the 4: 3 screen and 16: 9 screen .........................................................................................................22 Single Slide & Dual Slide LCD Display....................................................................................................................23 Overall Dimensions of the LCD KVM .................................................................................................................... 25 Chapter 2.....................................................................................................................................................................................27 Hardware Installation................................................................................................................................................................. 28 Stacking and Installation Precautions................................................................................................................................ 28 Standard Rack Mounting............................................................................................................................................28 KVM Modules Assembly & Removal......................................................................................................................31 Removal of the Keyboard Module.............................................................................................................................33 Expansion Module Installation...................................................................................................................................34 Single Device Installation.......................................................................................................................................... 37 Installation of Single Port LCD KVM Switch........................................................................................................... 40 Cascade Device Connection.......................................................................................................................................42 Chapter3......................................................................................................................................................................................46 Basic Operation.......................................................................................................................................................................... 46 Hot Plug..............................................................................................................................................................................46 Hot - Plug Computer Connection...............................................................................................................................46 Hot - Plug Console Port..............................................................................................................................................46 Connection Port Selection.................................................................................................................................................. 46 Switch the Selection Manually...................................................................................................................................46 OSD Menu Screen Selection......................................................................................................................................47 Hotkey Selection........................................................................................................................................................ 48 Power Off and Restart........................................................................................................................................................ 48 57 LCD KVM Console User Manual Open Way of LCD Screen ................................................................................................................................................49 Chapter4......................................................................................................................................................................................51 OSD Operating........................................................................................................................................................................... 51 OSD Introduction............................................................................................................................................................... 51 OSD Log in.........................................................................................................................................................................51 OSD Hot Key......................................................................................................................................................................51 OSD Main Menu................................................................................................................................................................ 52 OSD Main Menu Title........................................................................................................................................................52 OSDIntroduction of Function Keys................................................................................................................................... 52 F1 GOTO................................................................................................................................................................53 F2 SCAN................................................................................................................................................................ 53 F3 LIST...................................................................................................................................................................54 F4 QV..................................................................................................................................................................... 54 F5 EDIT..................................................................................................................................................................55 F6 SET....................................................................................................................................................................55 OSD ACTIVATING HOTKEY..........................................................................................................................57 SWITCH HOTKEY........................................................................................................................................... 57 CHANNEL DISPLAY MODE...........................................................................................................................57 CHANNEL DISPLAY DURATION..................................................................................................................57 CHANNEL DISPLAY POSITION.................................................................................................................... 57 SCAN DURATION............................................................................................................................................58 SET PASSWORD...............................................................................................................................................58 SET SUPER PASSWORD.................................................................................................................................58 CLEAR THE NAME LIST................................................................................................................................59 RESTORE DEFAULT VALUE..........................................................................................................................59 LOCK CONSOLE..............................................................................................................................................59 Appendix.....................................................................................................................................................................................60 Safety Instructions.............................................................................................................................................................. 60 General........................................................................................................................................................................60 Rack mounting............................................................................................................................................................61 Product Specifications........................................................................................................................................................61 LCD Module Specifications...............................................................................................................................................65 Warranty Conditions...........................................................................................................................................................66 57 About this manual LCD KVM Console User Manual This User's Guide will assist you in the effective use of the product features, including the installation, setup and operation of the equipment. You will find the following in this manual:

Chapter 1 Introduction - This chapter introduces the Rack KVM device system, including its functions, features, and advantages, and describes and introduces the front and rear panel components. Chapter 2 Hardware InstallationThis section describes how to install the product and the necessary steps - including basic stand-alone installation, multi-switch level connection installation, and IP module expansion installation. Chapter 3 Basic OperationExplain the basic operating concepts of the KVM switch. Chapter 4 OSD OperationProvides a complete KVM switch OSD (onscreen menu) introduction and explains how to use it. Appendix - Main specifications and other technical information about the associated KVM switch. 57 Description of Terms LCD KVM Console User Manual Symbol The parentheses indicate the keys that need to be entered. For example, [Enter] means to press the Indicates the text information that should be entered Enter key. For keys that need to be entered at the same time, they are placed in the same bracket, and the keys are joined by a plus sign. E.g:Ctrl+Alt 1.Numbers indicate the actual operating sequence numbers. The diamond symbol indicates that the information is provided for reference, but is not relevant to the procedure. The origin symbol indicates the sorting sub-item information, independent of the operation steps. Indicates the most important information. Product Information To find out more about KVM's products and how to use them more efficiently, please visit our website or contact an authorized dealer for more contact information. 57 LCD KVM Console User Manual Chapter 1 Introduction Products Introduction 4/8/16Ports USB/PS.2 LCD KVM Switch is a functional equipment that allows administrators to control 4/8/16pcs computers from a set of USB keyboards, mice, or a set of PS2 keyboards, mice. You can also use a single port LCD KVM switch as the computer keyboard, mouse, monitor external devices use; front panel also adds front USB expansion port, you can easily add an external USB mouse and keyboard operation;

support two-level cascade can be Single console to manage up to 256 computers;

In addition, according to the needs of users to expand the function, to KVM OVER IP transmission control mode, only need to add the product in the expansion card slot IP KVM module card, you can upgrade to remote network management digital KVM management device, user-friendly environment does not change the existing circumstances quickly and quickly upgrade the advanced control mode applications. There are four convenient ways to switch the computer in the installation: (1) Use the Port Select button on the front panel of the switch; (2) Enter the hotkey combination from the keyboard; (3) From the On-Screen Display (OSD) select. The auto-scan feature provides automatic scanning and monitors the computers in the installation architecture one by one. (4) Through the expansion of the IP module of the network port for remote network control operation even in the KVM above the computer. This product is very fast and easy to install, just simply connect the cable to the appropriate connection Port , no software settings, no cumbersome installation procedures, and there will be no incompatibility issues. As the device can directly access the keyboard input data, it can operate in a variety of operating platforms

(compatible PC, Mac, Sun, etc.). As it allows a single console to manage the computers connected to it, a set of KVM installations,(1) eliminates the cost of individual keyboards, monitors, and mice for each computer; and (2) saves the cost of additional equipment that can be used by the additional devices. This allows for the installation of a set of KVMs that can be managed from a single console. Space; (3) to save energy costs; (4) to avoid moving back and forth between the various computers inconvenience and waste. (5) the rapid upgrade to IP control mode remote network control mode. The series of LCD liquid crystal display can be divided into three models for you to choose:17inch19inch 19inch wide-screen The series of products according to the use of LCD components can be divided into single-pull pull mode, double-pull double pull mode, Which dual-rail design LCD display and keyboard / touchpad module can be individually sliding. To maximize the space in the data center, when not using the keyboard / touchpad, push it back into the rack to "hide", allowing the administrator to monitor the status of the computers in the device. 57 The modular design and installation of the product series, you can freely replace the actual needs of the KVM components to facilitate the free combination of different applications. According to the module type can be divided into three categories: VGA device type, DVI device type, CAT5 type, Port number can be divided into 1, 4, 8, 16 . LCD KVM Console User Manual 57 Product Features LCD KVM Console User Manual A group of USB console can manage 1, 4, 8 or 16 VGA or DVI interface computer control side supports USB and PS2 two interface types of keyboard, mouse device Can control two cascades ,cascade control up to 256 computers The front panel keypad, keyboard hotkey and on-screen menu (OSD) can be used to switch the computer Trojans invasion recognition KVM connected with the accused device BIOS-level access, do not have to worry about the risk of viruses and the accused computer does not need to install any software and the driver, the accused computer direct 17 "and 19" LCD display and keyboard, mouse, KVM integrated into one chassis, reducing the volume Front USB Port, convenient for user to extend USB peripheral keyboard and mouse dual slide design, LCD display and keyboard, mouse control panel can be individually pulled Unique single installation mode, more convenient technical staff to install Control terminal lock function, close the LCD display Push into the track, can automatically limit the lock, pull out the armrest automatically unlock LCD power button, you can turn off the monitor when not in use, save power, extend the life of the LCD can rotate 0-110 degree elevation angle, it is convenient for you to adjust the suitable viewing It is compatible with other KVM switches of our company and can be cascaded and extended Remote Control IP module, supports multiple browser applications to access Internet Explorer, Chrome, Firefox, Safari, Opera, Mozilla, Netscape, etc. You can upgrade the remote network control mode through the extended IP board Support OSD to set user login mode and increase KVM login security requirements Support high video resolution in local and remote IP mode - Support 480i, 480p, 720p, 1080i and 1080p LCD monitor angle

(1920 1200) Support wide screen resolution Extended IP remote control mode supports 1000M Ethernet control transmission requirements Support remote firmware update Remote can be based on the actual network bandwidth to transmit video frame rate, bit rate, the mouse pointer movement rate adjustment support DDC communication, to adapt to a variety of graphics devices The Auto Scan function monitors all computer operations Support cross-platform operation - Windows, Linux, Mac * and Sun *

PC connected to the keyboard and mouse using Keep Online simulation technology mouse and keyboard, equipment security and stability, fast switching without delay The remote IP control mouse is absolutely coincident and automatically follow The remote video form can be adjusted freely to meet different display screen display requirements Remote video support "one screen multi-display" function, you can watch a computer in a multi-computer screen controlled display screen can be zoomed non-polar function, any proportion of the size of the show 57 Multi-window overlay technology can display multiple windows on the same remote console, and LCD KVM Console User Manual select and control any windows. IP expansion module uses plug and play is installed, customers do not need to disassemble, you can quickly complete the expansion of equipment installation Convenient and friendly remote login mode, through the browser for Web page access and related settings and query Three user-level settings, multi-user group settings, suitable for a variety of management requirements Remote control desktop can be set according to user habits Two different mouse application mode Hardware Requirements Console Rear two USB Type A keyboard and mouse Pre-set a USB Type A type keyboard and mouse A set of USB interface mouse A set of USB interface keyboard Single-ended extension cable (optional) IP remote control terminal 1000M network interface (optional installation) Computer The following devices must be installed on each computer:

A VGA or DVI video display card USB Type A connection port PS2PS2 keyboard, mouse Port Cables KVM equipment provides six kinds of connection cables according to the user's use to choose:

LCD KVM switch single port DVI cable LCD Connector DB37P 57 LCD KVM Console User Manual Computer-side DVI-I + USB (Type A)+ PS2 keyboard (purple) + PS2 mouse (green) LCD KVM switch single port VGA cable LCD Connector DB37P Computer-side VGA + USB (Type A) + PS2 keyboard (purple) + PS2 mouse (green) VGA + USB (Type A) + PS2 Keyboard (Purple) + PS2 Mouse (Green) 57 DVI-I + USBType A + Audio LCD KVM Console User Manual KVM connection Computer connection Note: The cable length affects the quality of the display. If you need other lengths of cable, contact the merchant you purchased to purchase a cable suitable for this switch. CAT5 connection Dongle VGA + PS2 keyboard (purple) + PS2 mouse (green) CAT5 connection Dongle VGA + USB (Type A) 57 Operation System LCD KVM Console User Manual Operation System Version Windows Linux RedHat SuSE Debian Ubuntu UNIX AIX FreeBSD Sun Solaris Mac Novell Netware DOS Windows 2000/XP/2003/2008/Vista/7/10 9.0 or higher Fedora and above, RHEL AS 4, RHEL 5 10/11.1OpenSUSE 10.2; SLES 10 SP1 3.1/4.0 7.04/7.10 4.3 or higher 5.5 or higher 8 or higher OS 9.0 to 10.6 (Snow Leopard) 6.0 or higher 6.2 or later More operating system support: please pay more attention to the latest version of the relevant product compatibility. 57 Parts Front View LCD KVM Console User Manual According to the size of the LCD screen is divided into two styles, as shown below, the components of the description please see the figure after the serial number table describes the details. No 1 2 Part Upper handle Lock Function Description Pull the handle, slide the LCD module out and push it in Used to lock the LCD module, pull out the module must first unlock, push into the automatic locking 3 LCD screen cover Can be opened or closed with the handle, opening and closing 57 LED screen KVM Module KVM Key panel LCD KVM Console User Manual angle of 0-110 degrees 17 "or 19" LED LCD screen KVM modules are free to replace and remove The KVM Port manual switch function is completed by pressing the key The LCD KVM can be installed on the cabinet posts with screws Front mounting brackets Touch Mouse Pad KVM console mouse, can control the computer's computer 4 5 6 7 8 operation LCD module sliding track, can be telescopic freely Corresponds to the latch of the LCD module Used to control the LED screen display adjustment and switch Used to access an external USB keyboard or mouse 9 Slide rails 10 Keyhole 11 LCD Keypad Panel Front USB 12 Rear view The Rear View of this product series is a rear view of the Removable KVM Switch Module, and the functional description of each Hardware Port (refer to the description of the corresponding KVM Switch product brochure.) LCD KVM Single port Rear View LCD KVM 4 port VGA Rear View LCD KVM 8 port VGA Rear View 57 LCD KVM 16 port VGA Rear View LCD KVM Console User Manual LCD KVM 4 port CAT5 Rear View LCD KVM 8 port CAT5 Rear View LCD KVM 16 port CAT5Rear View LCD KVM 4 port DVI Rear View LCD KVM 8 port DVI Rear View According to the type of KVM ,the rear view of the product can be divided into three categories:

VGA Port This type of LCD KVM switch can be divided into 4 models according to the number of ports: single port, 4 ports, 8 ports, 16 ports. In addition, the control module of Remote Control IP can be selected according to the needs. CAT5 Port DVI Port single-port, four, eight. This type of LCD KVM switch can be divided into 3 models according to the number of ports: 4 ports, 8 ports, 16 ports, in addition can be optional Remote Control IP control module. This type of LCD KVM switch according to the number of Port can be divided into two models:

57 Front view of the 4: 3 screen and 16: 9 screen LCD KVM Console User Manual 17inch4: 3 screen 19inch 16: 9 screen 57 Single rail &Dual-rail LCD Console display Single-rail LCD KVM Console LCD KVM Console User Manual Dual-rail LCD KVM Console 57 LCD KVM Console User Manual Dual -Rail Slide View Dual-rail overall rear view 57 Overall Dimensions of the LCD KVM Single-rail single port KVM Console dimension:

LCD KVM Console User Manual 57 Single rail multi-ports KVM Console dimension:

LCD KVM Console User Manual 57 Dual-rail LCD KVM Console dimension:

LCD KVM Console User Manual 57 Chapter 2 LCD KVM Console User Manual Hardware Installation Stacking and Installation Precautions 1. Important safety information regarding the placement of the LCD KVM switch is listed in the appendix, please refer to it before proceeding. 2. Before installation, please make sure that all the devices connected to the power supply are turned off. You must unplug all the power cord of the computer with keyboard power on 3. LCD KVM switch packing stuffed with stuffing in the process of delivery to protect the product. Attach the protective film and filler to the LCD module and remove the filler before mounting. The LCD KVM switch can be placed in any suitable plane and is sufficient to securely support the weight of the equipment plus additional cables; Please make sure that the plane is clean and free from other debris that can affect the ventilation and normal operation of the switch. Standard Rack Mounting 1. Remove the mounting brackets and fasten the front bezel to the frame with screws. Slide the back plate with the rear flange toward the rack until the flange is against the chassis, and then use the screws to secure the rear flange to the chassis. 57 LCD KVM Console User Manual 2. Slide the LCD KVM unit onto the support flange, secure the front of the switch to the front of the rack with the screws provided in the package and lock. 57 3.Slide the rear connecting slide bracket along the side rails until it reaches the rear of the switch. LCD KVM Console User Manual 4. Use the screws provided in this package to secure the strip to the rear of the switch. At this point, you have completed the rackmountable LCD KVM switch for subsequent use. Note: There may be a difference between the two-rail mounting bracket and the single-slide carriage. For the dual-rail product, please refer to the following figure. 57 LCD KVM Console User Manual KVM Module assembly & disassembly This series of LCD screen and keyboard, mouse and the rear part of the KVM part of the components can be demolished separation, this design allows you to change the KVM components, or KVM components damaged KVM components dismantled after the return to the manufacturer for repair and replace. Please refer to the figure for loading and unloading operations:

1. Now put this series of products on the appropriate operating platform, ready for Screwdriver tools for subsequent use of removable screws. 57 LCD KVM Console User Manual 2. Remove the KVM assembly and the captive screws on the side brackets as shown to separate the KVM assembly from the front LCD assembly. 3.Please note the connector between the KVM module &LCD during the Removal and installation, or it may damage the connection interface and equipment function failure. 57 LCD KVM Console User Manual Disassembly of the Keyboard Module If you need to replace the LCD module part of the keyboard or repair this part, can also be demolished according to the following diagram. 1.The LCD KVM placed in the rack and fixed, the LCD panel turned up, revealing the keyboard, the mouse's operating surface. 2.The bottom of the keyboard panel has a circular hole, you can use your fingers through the circular hole, the top of the keyboard. 57 LCD KVM Console User Manual 3. Pull the keyboard from the limit slot gently, find the connection side of the USB interface, remove the USB from connection side, the keyboard could be taken out. Thus completing the demolition of the keyboard module. Note: If you replace the installation, please first plug the keyboard USB interface, then put the keyboard module into the limit slot. Expansion Module Installation If you buy a KVM switch, because you need to increase the remote control and operation, you can directly 57 with the dealer to buy our products supporting the IP module for equipment upgrades and expansion, the operation method is simple and quick, can quickly enhance the integrated management of KVM Application ability. LCD KVM Console User Manual 1. find the rear of the device, expansion slot outside the blank position for installation, you need to prepare a screwdriver for removal and installation tools. 2. Before installation, use a screwdriver to remove the two fixing screws on the blank. 1. Remove the blank after you can see the need to expand the installation of the IP module placement cavity, keep the screw removed down. 57 LCD KVM Console User Manual 2.Remove the extended IP module and push it gently into the recess in the mounting module cavity as shown. 3.After pushing the IP module to the bottom, fix the IP module with the two screws that have been removed before. 4. After installing the IP module, you need to follow the instructions of the IP module To install the software and configure the IP address of the device before you can connect the network cable to the switching device. After the installation is complete, you can access the network to log in. (For details, refer to the IP module's product manual.) 57 LCD KVM Console User Manual Single Device Installation NoteBefore the installation, make sure that the equipment is powered off. To prevent damage to the equipment during installation, make sure that all the devices installed are well grounded. VGA port KVM module installation To install a single-level KVM, refer to the following online diagrams (numbered in the order of steps on the online graph) and do the following:

1.Plug your USB keyboard and mouse into the USB console port on the back panel of the switch. 2.Using a set of KVM cables corresponding to the model, plug the VGA connector into the VGA Port of any available VGA port on the switch. 3.Plug the corresponding VGA video connector, USB or PS2 connector of the KVM cable into the corresponding port on the PC. 4.Plug the power adapter supplied with this package into the AC power source, and plug the other end of the power adapter into the power jack on the switch. 5.Connect the network cable to the IP port of the IP module. 6.Turn on the computer. Note:1. Make sure that all plugs are connected to the same group of KVM connection port jacks (all connected to Port1, or all connected to Port2). 2.IP module is an optional module of the product. If the product you purchased does not contain the module, please ignore the related operation in Step 5. 3.Before using the IP module, please make the appropriate configuration and network debugging after the access to the network you want to connect, or may fail to connect because of normal remote control. (Refer to the manual of the IP module product manual for how to use and debug the IP module. 57 LCD KVM Console User Manual CAT5 port KVM Module Installation To install a single-level KVM, refer to the following online diagrams (numbered in the order of steps on the online graph) and do the following:

1. Plug your USB keyboard and mouse into the USB console port on the back panel of the switch. 2.Use a set of CAT5e / 6-wire connectors to plug into any available CAT5 Port on the switch. 3. Plug a CAT5e / 6-wire connector into the CAT5 connector on the Dongle module of the KVM, and connect the corresponding VGA video connector, USB or PS2 connector of the Dongle cable to the corresponding port on the PC. 4. Plug the power adapter supplied with this package into the AC power source, and plug the other end of the power adapter into the power jack on the switch. 5. Connect the network cable to the IP port of the IP module. 6. Turn on the computer. Note:1. Make sure that all plugs are connected to the same group of KVM connection port jacks (all connected to Port1, or all connected to Port2). 2. The IP module is an optional module of the product. If the product you purchased does not include the module, please ignore the related operation in Step 5. 3. Before using the IP module, please make the appropriate configuration and network debugging after the access to the network you want to connect, or may fail to connect because of normal remote control. (Refer to the manual of the IP module product manual for how to use and debug the IP module.) 4LCD KVM conversion module is divided into two types: PS2 and USB port, you can connect your computer to choose the appropriate conversion module to use. 5Make sure you are connecting to a computer and LCD KVM switches have a good grounding protection altogether, or it may produce a video display problems 6For display problems caused by transmission distance, electromagnetic interference, common ground, etc., it is recommended to use Category 6 shielded network cable to connect and try to improve the display effect 57 LCD KVM Console User Manual DVI port KVM module installation To install a single-level KVM, refer to the following online diagrams (numbered in the order of steps on the online graph) and do the following:

1. Plug your USB keyboard and mouse into the USB console port on the back panel of the switch. 2. Insert the audio cable plug of the microphone and the speaker into the corresponding type port. 3. Using a set of DVI KVM cable connectors corresponding to this module to plug into any of the available Port ports on the switch, DVI to DVI port, USB Type B to keyboard port, mouse port, composite audio plug into the audio jack. 4. Connect the AC adapter to the AC power source, and plug the other end of the power adapter into the power jack on the switch. 5. Connect the network cable to the IP port of the IP module. 6. Turn on the computer Note:

1.LCD KVM conversion module is divided into two types: PS2 and USB port, you can connect your computer to choose the appropriate conversion module to use. 2.Please make sure that the computer and the LCD KVM switch you are connecting to have a good common earth ground, otherwise a video display problem may occur. 3.For display problems caused by transmission distance, electromagnetic interference, common ground, etc., it is recommended to use Category 6 shielded network cable to connect and try to improve the display effect. 57 LCD KVM Console User Manual Installation of Single Port LCD KVM Switch 57 LCD KVM Console User Manual Single-port LCD KVM switch choose KVM cables to connect instead of multi-port use KVM module, divided into two kinds: VGA and DVI according to the port type. VGA Single port LCD KVM 57 DVI single port LCD KVM Switch LCD KVM Console User Manual NoteConnect the DP37 port to the corresponding port on the back of the LCD, and then connect the video port of the other end to the video port of the computer. Then connect the port of PS2 or USB to the corresponding keyboard and mouse port of the computer, then power the computer and the LCD KVM switch. Cascade Device Connection This product can be cascaded to increase the number of control devices, combined with IP remote control mode can be flexibly used in a variety of user environment requirements. VGA Port LCD KVM Switch Cascade In the VGA switch Cascade mode, the keyboard, mouse and computer connections is same with the stand-alone connection, this part will not repeat them, the number part of the description is as follows:

1. A cascaded KVM switch can be connected in two ways by using a USB KVM cable (as shown in connection number 2 in the figure) or a PS2 KVM cable (as shown in connection number 1 in the figure) Connect to the upper-level switcher. 2.The number of computers connected to each level can be freely increased or decreased according to your requirements. Refer to the connection method shown in figure 3. 3. Between the level of IP module can be optional remote control, can also be handed over to the KVM switch from the top of the local and remote as a unified control and management operations. NoteThis product cascade mode is divided into two levels, so you need to set the cascade connection mode switch OSD Menu with two levels of hotkey for two different hotkey combinations, or the OSD can not be started when cascade.(Refer to the OSD chapter for details on the OSD Hot Key settings.) Connection diagram please see the following figure (VGA port LCD KVM switch cascade) 57 LCD KVM Console User Manual CAT5 Port LCD KVM Switch Cascade In switch cascade mode, the keyboard, mouse and computer connections and stand-alone connection is the same, this part will not repeat them, the number part of the description is as follows:

1.The cascade KVM switch, have two connection methods, the use of USB KVM conversion module cable or PS2 KVM conversion module cable and a switch to the next level to connect. (Refer to the description of the CAT5 KVM switch product manual for how to connect the converter module.) 2.The number of computers connected to each level can be changed according to your needs. Refer to the connection port shown in figure 2, which is the connection port of Remote Control mode. It can provide the user to connect the control device through Remote Control console. Remote Control Port switcher usage and connection method(Refer to the CAT5 KVM switch product manual for instructions.) 3.IP modules can be selected for remote control, and can also be controlled by local and remote KVM switches from the upper layer as a unified control and management operation. NoteThis product cascade mode is divided into two levels, so you need to set two levels of OSD Menu hotkey for two different hotkey combinations in cascade mode, otherwise the cascade connection can not start the OSD normally. The OSD Hot Key settings are described in detail in the OSD chapter.) Please make sure that your computer and LCD KVM switch are well grounded. Otherwise, the video display problem may occur. For the display problems caused by transmission distance, electromagnetic interference, common ground, etc., it is recommended to use Category 6 Screen cable to connect, try to improve the display. 57 The connection diagram is shown in the following figure (CAT5PortLCD KVM Switch Cascade). LCD KVM Console User Manual 57 VGALCD KVM Switch Cascade LCD KVM Console User Manual CAT5LCD KVM Switch Cascade 57 LCD KVM Console User Manual Chapter3 Basic Operation Hot Plug The KVM switch supports hot-plug, removing and removing components by unplugging the cables connected to the computer's port without shutting down the switch. To make the hot swap function work properly, follow these steps:

Hot Plug Computer Connection In order for OSD Menu to correspond to the KVM connection port changes, you must reset OSD Menu to display the latest connection port information, OSD menu settings. Please refer to the OSD Menu section for more information about functions and usage. Note: If your computer's operating system does not support hot-plug functionality, this feature may not function properly. Hot Plug Console Port This product also provides keyboard, mouse and display hot-plug function. This product provides keyboard and mouse port for two interface types. Users can select the corresponding device connection type according to their usage and carry out corresponding control operation. Note: If you access the USB and PS2 keyboard, mouse device, you do not have to use two types of devices, otherwise, may cause the accused computer equipment mouse and keyboard response exception. Connection Port Selection The KVM switch can be used to quickly switch to any computer connected to the KVM in three modes:

manual key selection, OSD Menu screen selection, and hotkey selection. Switch the Selection Manually Use the buttons on the front control panel to select a port. 57 LCD KVM Console User Manual KVM switch button located in the top of the keyboard operating area, divided into three blocks, from left to right in order is the online indicator display area, Port switch to select the display area, Port switch digital button area. Online Indicator Display Area The LEDs in the display area are lit when the controlled computer connected to KVM Port is connected to the line. The LED indicating the port number is illuminated and you can see the KVM online Port status. Port Switch the Display Area The digital LED indicator in the display area shows the port serial number of the current working port when the working status is displayed, or the numeric key serial number you input when the key switch port changes. Port Switches the Numeric Keypad Area This area has the numeric keys of [0] - [9] and [RST] (reset button), [ENT] (confirm button), the number keys are used for Port selection, input the corresponding port number, ENT to finish the switch of Port. To reset the KVM switch, you need to click [RST] for 3-5 seconds to complete the KVM switch restart. OSD Menu Screen Selection LCD OSD Menu key operation AUTOPress the key to set the display setting for the screen to automatically adjust to the resolution MENUPress the key to perform the main function OSD Menu of the LCD screen, to select and set various functions of the screen LEFTPress the key to select the direction of the OSD menu, and move the current selection to the left by one unit RIGHTPress the key to select the direction of the OSD menu and move the current selection to the right by one unit EXITPress to exit the OSD menu POWERPressing the button allows you to turn the LCD screen on and off LED display for the LCD screen status indicator, you can indicate three working status:

red, green, do not show the state. "Red" indicates that the LCD screen has been powered, but no video signal input. "Green" indicates that the LCD normally displays the video signal of the controlled computer. "No display" means the LCD screen has been powered off. 57 LCD KVM Console User Manual KVM OSD Menu operation Refer to the OSD Operation chapter for more information. Hotkey Selection This product offers four hotkey switching methods:

SCRLL+SCRLL+NUM CTRL+CTRL+NUM ALT+ALT+NUM SHIFT+SHIFT+NUM The default hotkey toggle key combination is [SCRLL] + [SCRLL] + [NUM] where [NUM] is the keyboard number 1-16, the keyboard combination hotkey input complete carriage return completed the command transmission, KVM switch will switch the corresponding number Of the Port computer. If you want to change the key combination of the hotkey, you can set and change it in the corresponding option of OSD Menu. Power Off and Restart If you need to power off the KVM switch, do the following before turning it back on:

1.Unplug the power supply to the KVM. 2.Turn off all computers connected to the KVM switch. 3.Wait about 10 seconds, then reconnect the KVM switch. 4.Turn on the computer. Note: If the PS2 KVM cable is connected to the PC, you must connect the PS2 cable to the PC before powering on. Otherwise, the keyboard and mouse will not operate normally. 57 Open Way of LCD Screen LCD KVM Console User Manual When using, the LCD assembly can be unlocked from the side track by the handle of the upper part of the LCD unit. After unlocking, the LCD module can be pulled out from the slide rail. (Refer to the diagram above for operation) To open the LCD display screen, you can flip the screen upwards to fit the viewing angle only. The maximum angle that the LCD screen can be opened is 105 degrees -120 degrees. You can view the screen at any angle you like. 57 LCD KVM Console User Manual AUTO LOCK UNLOCK The screen will automatically pull out the slide after the brake lock device to prevent the random sliding LCD screen components to bring the instability and may cause damage to the user collision. After the brake lock is activated, the LCD screen will limit the operation of pushing the slide rail. If you want to do the push-in operation of the LCD module, the unlocking action must be done first, and the unlocking switch is on both sides of the slide rail. (Please refer to the figure above for the specific operation). After unlocking, the LCD assembly can be pushed into the slide rail. Note1.Push the LCD assembly into the slide, the unlock action and push action should be careful, improper operation may clip your finger. 2.When using the keyboard or mouse, do not use the body to depress the LCD module Otherwise, it may cause the slide rail to deform or not be able to be pushed into the slide rail 57 Chapter4 OSD Introduction LCD KVM Console User Manual OSD Operation OSD (On Screen Display), provides a menu driven interface to handle the computer switching procedure to provide instant access to any computer on the installation. OSD Log in The OSD function provides a two-level (administrator / user) password mechanism. The factory default setting is no need to login password authentication, so you are the first time to open the OSD main menu, no need to enter the login password to enter the OSD main menu screen for the corresponding operation. If you want to add this function, you can enter the OSD menu, in F6 "SET" option to set the login password is set successfully, the subsequent login requires the correct administrator / user password to enter the OSD menu Interface operation. When you enter the setting options, some functions may need to be edited and modified by the administrator. The default administrator password is admin. You can also modify and change them as needed. OSD Hot-Key By default, you can type the [CTRL] key twice to have the OSD menu appear on the screen of the controlled display and see the connection information and status information about the connected computers on the KVM switch. Note: You can change the keyboard hotkey on the OSD menu according to your needs. This product provides 4 sets of optional OSD menu hotkey combinations. You can select the operation according to your needs. (Please refer to the OSD menu for detailed description. ) 57 OSD Main Menu Active OSD, following picture will be shown on the screen:

LCD KVM Console User Manual F1 --- F6 at the bottom of the screen is the function setting of OSD menu, and corresponding operation and setting of corresponding function by keyboard. After entering the OSD main screen, the port number in the center of the screen is the port number of the selected PC. To move up and down through the list one line at a time, use theArrow Keys, press Enter to select the switch port. Please pressEscto exit the OSD menu interface To move up or down a row in the list, use thearrow keys. If the number of rows in the list is larger than the number that the screen can display, the screen scrolls. When the OSD menu is closed, a small blue window will appear on the screen showing the port number that is currently switched to. OSD Main Screen Headings Explanation This column lists the port numbers for all the CPU ports on the installation. The simplest method to access a particular computer is to move the highlight bar to it, then press [Enter]. If a port has been selected for Quick View scanning, an arrowhead symbol displays in this column to indicate so. The computers that are powered on and are on line have an arrowhead symbol in this column to indicate so. If a port has been given a name, its name appears in this column. Heading PN QV PC NAME OSD Function OSD functions are used to configure and control the OSD. For example, you can: rapidly switch to any port;

scan selected ports only; limit the list you wish to view; designate a port as a Quick View Port; create or edit 57 a port name; or make OSD setting adjustments. To activate the OSD function key:

1. Press any function keyF1--- F6 at the bottom of main screen to input the function key. 2. On the sub-menu, move the selection column to the option, and then press the {Enter} key. 3. Press theEsckey to return to the previous menu. LCD KVM Console User Manual F1 GOTO Press the F1 key to start the GOTO function. The GOTO function allows you to switch directly to the connection port by typing the port name or its port number. 1. To use NAM method, move highlight bar to NAME, press Enter, input name of a port, then press

[Enter] to confirm. 2. To use PN method, move highlight bar to PN, press Enter, input port number, then press Enter to switch. If the port number is invalid, it will remind the user to input again. Note:1. When keying name, if there is a matching name, the matched name will appear on the screen, just press [Enter] to switch to that port. 2.In the "PN" port input box, only allow the input of numbers, such as the input of other characters are regarded as invalid input, and can hear the equipment issued by the warning tone. To return to main menu, press [Esc]. F2 SCAN The "SCAN" function allows you to perform automatic port scanning of the connected computers. Users can switch ports in order to view the corresponding port computer status. The SCAN function can automatically scan from current selected port, the scan interval can be set by users. When scanning, a small window on the screen indicates the current port number. 57 Press [Space] to stop scanning, and the KVM switches to the port last scanned. LCD KVM Console User Manual F3 LIST The LIST function lets you broaden or narrow the scope of which ports the OSD displays on the main screen. Many of the OSD functions only operate on the computers that have been selected for listing on the main screen with this function. The choices and their meanings are given in the table below:

Choice ALL QVIEW POWERED ON Meaning Lists all of the ports on the installation. Lists only the ports that have been selected as Quick View Ports. Lists only the ports that have their attached computers powered on. ON POWERED QVIEW QVIEW + NAME

+

NAME Lists only the ports that have their attached computers powered on and have been selected as Quick View Ports. Lists only the ports that have been selected as Quick View Ports and have name. Lists only the ports that have names. Move the highlight bar to the choice you want, then press [enter]. An icon appears before the choice to indicate that it is the currently selected one. After you make your choice and press [Enter], you return to the OSD main screen with the newly formulated list displayed. F4 QV QV function can select port as Quick View. 57 LCD KVM Console User Manual Move the highlight bar to a port, press [F4], an icon of up triangle appears. Press [F4] again, the icon disappears. F5 EDIT EDIT function creates or edits the name of a port. Press [F5], a pink edit box will appear on the screen. Input name, and then press [Enter], the port is set a name and it will also appear on the screen. F6 SET SET function settings can be set to the administrator and the user to set the OSD menu. The related functions and user rights related settings, such as management settings login password, display mode, switch hotkey adjustment and so on. 57 LCD KVM Console User Manual To change your settings:

1. Move the selection column 2.After selecting an item, it, double-click the mouse or move the selection column to the option, and then press the [Enter] key, an icon will appear. Select the option before to indicate that the item has been selected. The settings are described in the following table:

the sub-menu and the further options provided will appear. To select to this option, press Enterto enter a setting option. Settings OSD ACTIVATING HOTKEY OSD Menu Activates hotkey combination selection Function SWITCH HOTKEY SCAN DURATION SET PASSWORD SET SUPER PASSWORD CLEAR THE NAME LIST RESTORE DEFAULT VALUE Reset LOCK CONSOLE settings KVM port switch hot-key combination selection setting Port scan dwell time setting User login password settings The administrator login password settings Clear the port name setting OSD Menu Password Login Function settings 57 OSD ACTIVATING HOTKEY LCD KVM Console User Manual It provides you with four hotkey combinations:

You can use the keyboard to move cursor to select, and then press Enter key to save. The default is to use CTRLCTRLas the OSD menu start hotkey. SWITCH HOTKEY It provides you with four hotkey combinations:

SCRLLSCRLLNUMCTRLCTRLNUMALTALTNUM SHIFTSHIFTNUMYou can use the keyboard to move cursor to select, and then press Enterkey to save. The default is to useSCRLLSCRLLNUM as the OSD menu start hotkey. NUM is the numeric keypad of the keyboard. The valid numeric range is 1 - 16. 57 SCAN DURATION LCD KVM Console User Manual Duration for scanning one port. Options are 3 seconds, 5 seconds, 10 seconds, 15 seconds, 20 seconds, 30 seconds, 40 seconds, 60 seconds. Move the highlight bar to an option and press [Enter] to select it. SET PASSWORD Set new password. First enter old password, then enter new password and confirm it. The new password is set. If error occurs, the screen will remind users. SET SUPER PASSWORD When setting the administrator password, you need to enter the correct password. Before new password is updated, input the previous password twice, the new password to take effect 57 CLEAR THE NAME LIST LCD KVM Console User Manual This function clears the name of a port in the OSD menu. If you use this function, all the port names will be emptied, so please do it carefully. When doing this, you need to verify the password of the administrator, input Ykey, then pressEnter to confirm the operation. To cancel this operation, inputNkey, and then pressEnterto confirm the cancel operation, or keyboard input Escdirectly back. RESTORE DEFAULT VALUE Restore settings to default value. This setting will make all the OSD menu options to restore the initial settings, so please be careful to do this. When doing this, you need to verify the password of the administrator, input Ykey, then pressEnter to confirm the operation. To cancel this operation, inputNkey, and then pressEnterto confirm the cancel operation, or keyboard input Escdirectly back. LOCK CONSOLE You cannot switch or scan after you lock the console (including switch by push button on the panel or OSD). You need to enter password to set. Note: After Locking the console, you can also unlock the console by this option. It also needs password verification. Descriptions of the OSD Menu functions may vary. Refer to the description of each interface KVM switch manual for details. 57 LCD KVM Console User Manual Appendix Safety Instruction In General This product is for indoor use only. Please read all the instructions for future reference. Follow all the warnings and instructions on the device. Do not place this equipment on any unstable surface (such as cart, stand, table, etc.). If this equipment falls, it will cause serious damage. Do not use this equipment near water. Do not place this equipment near or over the radiator or heating equipment. The enclosure is provided with slots for heat dissipation and ventilation. To prevent overheating during operation, do not block or cover the openings. Do not place the device on a soft surface (such as a bed, sofa, blanket, etc.). This will block the fan opening and can not be placed in a sealed environment unless proper ventilation is provided. Do not spray any liquid on the device. Before cleaning, please unplug the power from the wall socket. Do not use any liquid or foam cleaner. Use a damp cloth to clean it. Please use this equipment according to the type of power supply on the label. If you are not sure whether the power supply type is available, please contact your dealer or your local power company. This equipment is designed for IT distribution system with 100V ~ 230V phase-to-phase voltage. To prevent damage to your device, it is important that all equipment be properly grounded Do not place anything on the power cord or cable, and route the power cord and cable routing to avoid tripping over it. If the equipment uses an extension cord, make sure that the total capacity of all products using the line does not exceed the current carrying capacity of the line. Ensure that the total current of all products plugged into the wall outlet does not exceed 15A. Use a surge suppressor, regulator, or uninterruptible power supply (UPS) to help protect your system from sudden, transient, and reduced power. Please fix the system cable and power cord properly, and make sure nothing is pressing on the cable. Do not insert objects into the machine through the slots of the housing. There is a risk of exposure to dangerous voltage points or short-circuiting of parts resulting in fire or electric shock. Do not attempt to repair the equipment by yourself. Please consult a qualified service person for support. If any of the following conditions occur, unplug the unit from the wall outlet and return it to a qualified service representative for repair. The power cord or plug is damaged or worn Liquid is spilled into the unit The device is exposed to rain and water The device has been dropped or the housing has been damaged The function of the device is obviously changed 57 The machine cant be operated normally as instructed by the operating instructions. Adjustment only for the control functions covered by the operating instructions, and other inappropriate operations may cause damage, requiring more qualified personnel to perform repairs LCD KVM Console User Manual Cabinet Installation Before cabinet installation, make sure that the fixing device is securely fastened to the rack and extended to the ground. The weight of the whole rack can be dispersed on the floor. Mount the front and side securing devices in a single rack or the front-end fixtures in combination with multiple racks before starting rack work. Install from the bottom to up in the cabinet, and install the heaviest things first. When extending the equipment from the rack, make sure that the rack is stable and stable. Be careful when releasing the latch by pressing the device rails and sliding the unit into the rack. The track of the slide rail may clip to your finger. After mounting the device to the rack, carefully spread the rails to the locked position, and then slide the unit into the rack. Do not overload the AC supply branch circuit that supplies power to the rack. The total load capacity of the rack should not exceed 80% of the branch circuit. Make sure that all equipment used on the rack - including electrical outlets and other power connectors - is properly grounded. Make sure you have provided proper airflow for the equipment on the rack. Make sure that the operating temperature of the rack environment does not exceed the maximum operating temperature set by the manufacturer. Do not stand on or stand on any other equipment while you are servicing other equipment on the rack. WARNING: Slide / rail (LCD / KVM) mounting equipment can not be used with support brackets or work areas. Specification VGA Series LCD KVM Switch Specification 57 Connectors Function Direct Cascade(Max) 4 4 64 LCD KVM Console User Manual 8 8 128 16 16 256 Port Selection Console Connectors Computer Port Video Keyboard Mouse Expansion Port Monitor Keyboard, Mouse Power IP module network port Connection Port Selection KVM reset IPModule reset IP Module restored initially Computer Select port Computer Online port IP module network port Keyboard Mouse OSD Menu, Front Panel Hot-Key, Hot-key, Remote Control IP

(Optional) 17\19\19Wide LED Screen 1 x USB Type A Female 1 x USB Type A Female 1 x USB Type A FemalePrepositive port for keyboard, mouse 4 x VGA DB15bluef emale 8 x VGA DB15bluefemale 16 x VGA DB15bluefemale 1 x DC Jack 1 x RJ45 KVM operation panel Numeric buttons KVM operation panel function buttons 1 x Semi-embedded keys 1 x Semi-embedded keys Two-digit LED display LED 4 x red 8 x red 16 x red 1 x green 1 x orange USBPS2 Connectors Toggle Switch LED Indicator light Analog Mode Maximum resolution video Scan time interval 1920 x 1200 @ 60HZLocal and remote 35101520304060 secondsdefault 3 seconds Operation Environment Operating temperature Storage temperature Machine Attributes Humidity Chassis Single slide size Dual slide size Weight 0-50

-20-60 0-80%RH,No condensation Metal 555 x 445 x 45mm 645 x 443 x 45mm 16.6KG-18.1KG 57 LCD KVM Console User Manual CAT5 Series LCD KVM Switch Specification Function Computer Connections Direct Cascade(Max) 4 4 64 8 8 128 16 16 256 OSD Menu, Buttons, Hot-key, Remote Control IP (Optional) Video 17\19\19wide-screen LCD Monitor Connector Port Selection Console Connectors Computer Connectors Keyboard Mouse Expansion Port Video keyboard&

mouse conversion module Conversion module port Power IP module network port Connection Port Selection KVM reset IP Module reset IP Module restored initially Computer Select port Computer Online port IP module network port Keyboard Mouse Toggle switch LED Indicator light Analog mode Maximum resolution video Scan time interval Operation Environment Operating temperature Storage temperature Machine Attributes Humidity Chassis Single slide size Dual slide size Weight 57 1 x USB Type A Female 1 x USB Type A Female 1 x USB Type A Female( Prepositive USB port for keyboard, mouse 4 x USB or 4 x PS2 8 x USB or 8 x PS2 16 x USB or16 x PS2 4 x RJ45 8 x RJ45 16 x RJ45 1 x DC Jack 1 x RJ45 KVM operation panel Numeric buttons KVM operation panel function buttons 1 x Semi-embedded keys 1 x Semi-embedded keys Two-digit LED display LED 4 x red 8 x red 16 x red 1 x green 1 x orange USBPS2 1920 x 1200 @ 60HZ local & remote 35101520304060 secondsdefault 3 seconds 0-50

-20-60 0-80%RH,No condensation Metal 555 x 445 x 45mm 645 x 443 x 45 mm 16.6KG-18.1KG DVI Series LCD KVM Switch Specification Function Connectors Direct 4 4 8 8 LCD KVM Console User Manual OSD Menu, Buttons, hot keys 17\19\19Wide-Screen LCD Monitor 1 x USB Type A female 1 x USB Type A female 1 x USB Type A Famale (Prepositive port for Keyboard, mouse) 4 x Mini Stereo Female(Pink) 4 x Mini Stereo Female(green) 4 x USB Type B Female 4 x DVI-I 4 x Mini Stereo Female(black) 8 x Mini Stereo Female(Pink) 8 x Mini Stereo Female(green) 8 x USB Type B Female 8 x DVI-I 8 x Mini Stereo Female(black) 1 x DC jack KVM operation panel Numeric buttons KVM operation panel function buttons 4 x red Two-digit LED display LED 8 x red USB Type A 1920 x 1200 @ 60HZ Local 35101520304060secondsdefault 3 seconds 0-50

-20-60 0-80%RH,No condensation Metal 555 x 445 x 45mm 16.6KG-18.1KG Port Selection Console Port Connectors Monitor Keyboard Mouse Expansion Port Microphon e Computer Port Audio speakers Keyboard, Mouse Video Mixed audio port Toggle switch Power Connection Port Selection KVM reset LED Indicator light Analog mode Computer Select port Computer Online port Keyboard, Mouse Maximum resolution video Scan time interval Operation Environment Operating temperature Storage temperature Machine Attributes Humidity Chassis Size Weight 57 LCD Module Specifications LCD KVM Console User Manual Function 17inchLCD module 19inchLCD module 19inchwide-screen LCD LCD Display Assembly LCD Screen Size Ratio LCD Screen Type Viewing Area Resolution Support color Contrast Backlight Pixel spacing LEDService life Nominal Input Voltage 17inch4:3 19inch4:3 module 19inch16:9 SXGA TFT-LCD Wide AHVA TFT-LCD 337.920(H) 270.336(V) 376.32 (H) x 301.056 (V) 1280*1024@60HZ 16.7M colorRGB 6 bit + Hi_FRC 408.96(H) x 230.04(V) 1980*1080@60HZ 16.7Mcolor,True 8 bit 0.264x0.297mm 1000 : 1 (Typ) LED 0.294x0.294mm 100,000Hours

+5.0V 300*300um Keyboard Keyboard Layout Ultra-thin US100 key,Stand alone Removable keyboard. (Keyboard language format Mouse Compatible Port Service life Mouse Type Port X/Y resolution Service life Microsoft Windows9Me/NT/2000/XPWIN7Server2003 WIN8WIN10 Standard PS/2;USB Chocolate keyboard optional)

>1,000,000 times Touch Mouse Standard PS/2 1000 point/inch,40x40/mm)

>1,000,000 times 57 Warranty Conditions LCD KVM Console User Manual The Company shall not be liable for damages up to the amount paid by the Customer for the Products. In addition, the Company does not assume any direct, indirect, special, incidental or consequential damages resulting from the use of this product or the enclosed CD-ROM, documentation, etc; The Company makes no warranty, express, implied or statutory, regarding the content and use of this document and specifically disclaims any implied warranties of merchantability, fitness for a particular purpose, suitability or fitness for a particular purpose. 57