PL370/470 Cradle Quick Reference Guide 2 PL370/470 Cradle 1999 - 2006 SYMBOL TECHNOLOGIES, INC. All rights reserved. Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Symbol products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Symbol products. Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Symbol Technologies, Inc. One Symbol Plaza Holtsville, N.Y. 11742-1300 http://www.symbol.com Warranty For the complete Symbol hardware product warranty statement, go to:
http://www.symbol.com/warranty. Patents This product is covered by one or more patents. For patent information go to:
http://www.symbol.com/patents. Quick Reference Guide 3 Introduction The PhaserLink 370/470 Radio Frequency (RF) cradle acts as a stand, host communication interface and a charger for the Phaser RF scanner. For convenience, the cradle can sit on a desktop or be mounted on a wall. The cradle receives data from the scanner via radio frequency (RF) transmissions through the antenna, then transmits that data to the host device through an attached cable. The cradle also charges the scanners battery pack (in the scanner). Two versions of the cradle are available:
PL470 cradle: radio retail version. PL370 cradle: radio industrial version. This Quick Reference Guide provides basic instruction on the set up and use of the cradle. Unless otherwise noted, the term PhaserLink refers to all versions of the cradle. Equipment Supplied The following equipment is supplied:
- Two Screws (for wall mounting).
- One Velcro strip (for desk mounting).
- Four rubber feet (for desk mounting).
- This Quick Reference Guide.
- PhaserLink cradle. Save the shipping container for storing or shipping. Inspect all your equipment for damage. If anything is damaged or missing, call your authorized Customer Support Representative immediately. Related Documentation
- P370/470 RF Scanner Product Reference Guide, p/n 72-38495-xx
- P370/470 RF Scanner Quick Reference Guide, p/n 72-38493-xx. 4 Parts Charging LED Antenna Pairing Label Scanner Support Tab Charging/
Communication Contacts PL370/470 Cradle COM 1 Port Power Port Wall-mounting Socket 1 Wall-mounting Socket 2 Connecting to the Host COM1 Power Port To connect the cradle to a host:
1. Insert the appropriate interface cable from the host computer into the COM1 port. 2. Connect the power connector of the power supply (p/n 50-19000-101) into the cradle power port. (The cradle cannot be powered by the host computer.) 3. Connect the appropriate line cord to the power supply and the other end to an AC power source. Quick Reference Guide 5 Wall Mounting Before wall-mounting the cradle, the scanner support tab must be changed from the desk-mount position to the wall-mount position.. 1 1. Lift the scanner support tab out of the top part of the cradle and replace it in the wall-mount position as shown. 2. Seat the cables from the bottom of the cradle in the grooves along the length of the cradle so that the bottom of the cradle is smooth and flat. Desk Mount Wall Mount 2 Cable Grooves 3 3. Secure two screws (included) to the wall. A template is provided on page 14.
- Fasten the screws provided into the wall where the cradle should hang, leaving about 1/8
(0.3 cm) of the screw outside the wall for the cradle wall mounting sockets. 4. Place the cradle over the screw heads and slide down until it fits into place. Slight pressure upwards should not move the cradle. 5. Position the antenna vertically, pointing toward the ceiling. 6. Place the Phaser scanner in the cradle. 6 PL370/470 Cradle Inserting Phaser in the Cradle Place the Phaser scanner in the cradle so that the top of the scanner sits in the larger part of the cradle and the metal contacts on the bottom of the scanner touch the contacts on the cradle. Pairing The wireless connection between the scanner and cradle is the low power radio transmission through RF transceivers in both the scanner and cradle. Communication consists of bidirectional message packets. However, the scanner and cradle must be paired for this communication to work. NOTE After a new host is installed at the cradle, re-scan the pairing bar code. This allows the cradle to notify the scanner of the change in the host device. To pair the scanner with the cradle:
1. Scan the pairing bar code on the top of the cradle. A duplicate pairing bar code 2. is located in the well on the bottom of the cradle. Insert the scanner into the cradle (recommended but not required). Note that data cannot be scanned until linking (pairing) is complete. 3. During pairing there is an exchange of information between the scanner and the cradle. This occurs in a few seconds if the scanner is in the cradle and over a minute if the scanner is not in the cradle. 4. After the exchange is complete, the scanner and cradle are paired. Successful pairing is indicated by a warble beep; failure, or unsuccessful pairing, is indicated by a low/high beep. Sending Data to the Host Computer The cradle receives data from the scanner and transmits it to the host computer via the interface cable. Recharging the Battery in the Phaser To charge the scanners battery, place the scanner in the cradle ensuring the metal contacts on the bottom of the scanner touch the contacts on the cradle. A Quick Reference Guide 7 complete charge takes up to 4 hours, depending upon the remaining charge in the battery. Charging LED Once the scanner is placed in the cradle, it waits 15 minutes to start charging the battery in the scanner. The LED indicates the charging status as follows:
LED Off Slow Blink Fast Blink On Description The scanner is not in the cradle. Scanner is in cradle but not charging. Scanner is in cradle and charging. Scanner is in cradle and the charge cycle is complete. check the system power. check for loose cable connections. Troubleshooting If the cradle does not work after following the operating instructions in this guide:
ensure the scanner is sitting properly in the cradle. Cleaning Wipe the cradle periodically with a lens tissue or other material suitable for cleaning optical material, such as eyeglasses.
CAUTION Do not pour, spray or spill any liquid on the cradle. Regulatory Information All Symbol devices are designed to be compliant with rules and regulations in locations they are sold and are labeled as required. Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol Technologies, could void the user's authority to operate the equipment.
CAUTION Only use Symbol approved and UL Listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source. Country Approvals Regulatory markings are applied to the device signifying the radio (s) are approved for use in the following countries: United States, Canada, Australia, Japan and Europe. Please refer to the Symbol Declaration of Conformity (DoC) for details of other country markings. This is available at http://www2.symbol.com/doc/. Operation of the device without regulatory approval is illegal. 8 PL370/470 Cradle Health and Safety Recommendations Ergonomic Recommendations
CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.
- Reduce or eliminate repetitive motion.
- Maintain a natural position.
- Reduce or eliminate excessive force.
- Keep objects that are used frequently within easy reach.
- Perform tasks at correct heights.
- Reduce or eliminate vibration.
- Reduce or eliminate direct pressure.
- Provide adjustable workstations.
- Provide adequate clearance.
- Provide a suitable working environment.
Improve work procedures. Vehicle or Forklift Installation RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. Position your device within easy reach. Be able to access your device without removing your eyes from the road. Warnings for Use of Wireless Devices Please observe all warning notices with regard to the usage of wireless devices. Potentially Hazardous Atmospheres You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipement. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics or healthcare facilitlies. These requests are designed to prevent possible interference with sensitive medical equipement. Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research. Quick Reference Guide 9 Persons with Pacemakers:
turned ON
- Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when
- Should not carry the device in a breast pocket
- Should use the ear furthest from the pacemaker to minimise the potential for interference. If you have any reason to suspect that interference is taking place, turn OFF your device. Hearing Aids The wireless device may interfere with some hearing aids. In the event of interference you may want to consult your hearing aid supplier to discuss solutions. Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device. FCC / EU RF Exposure Guidelines Safety Information The device complies with Internationally recognised standards covering Specific Absorption Rate
(SAR) related to human exposure to electromagnetic fields from radio devices. Reducing RF Exposure - Use Properly It is advisable to use the device only in the normal operating position. Handheld Devices To comply with FCC RF exposure requirements, this device must be operated in the hand with a minimum separation distance of 20 cm or more from a person's body. Other operating configurations should be avoided. Laser Devices Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. EN60825-1:1994+ A1:2002 +A2:2001 IEC60825-1:1993+A1:1997+A2:2001 The laser classification is marked on one of the labels on the device. Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations:
CAUTION Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure. Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful. Laser Labeling In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to the user:
ENGLISH CLASS 1 CLASS 2 CLASS 1 LASER PRODUCT LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT HEBREW 10 DANISH / DANSK KLASSE 1 KLASSE 2 KLASSE 1 LASERPRODUKT LASERLYF SE IKKE IND I STRLEN KLASSE 2 LASERPRODUKT DUTCH / NEDERLANDS KLASSE 1 KLASSE 2 KLASSE-1 LASERPRODUKT LASERLICHT NIET IN STRAAL STAREN KLASSE-2 LASERPRODUKT FINNISH / SUOMI LUOKKA 1 LUOKKA 2 LUOKKA 1 LASERTUOTE LASERVALO L TUIJOTA SDETT LUOKKA 2 LASERTUOTE PL370/470 Cradle ITALIAN / ITALIANO CLASSE 1 CLASSE 2 PRODOTTO AL LASER DI CLASSE 1 LUCE LASER NON FISSARE IL RAGGIOPRODOTTO AL LASER DI CLASSE 2 NORWEGIAN / NORSK KLASSE 1 KLASSE 2 LASERPRODUKT, KLASSE 1 LASERLYS IKKE STIRR INN I LYSSTRLEN LASERPRODUKT, KLASSE 2 PORTUGUESE / PORTUGUS CLASSE 1 CLASSE 2 PRODUTO LASER DA CLASSE 1 LUZ DE LASER NO FIXAR O RAIO LUMINOSO PRODUTO LASER DA CLASSE 2 FRENCH / FRANAIS CLASSE 1 CLASSE 2 PRODUIT LASER DE CLASSE 1 LUMIERE LASER NE PAS REGARDER LE RAYON FIXEMENT PRODUIT LASER DE CLASSE 2 SPANISH / ESPAOL CLASE 1 CLASE 2 PRODUCTO LASER DE LA CLASE 1 LUZ LASER NO MIRE FIJAMENTE EL HAZ PRODUCTO LASER DE LA CLASE 2 GERMAN / DEUTCH KLASSE 1 KLASSE 2 LASERPRODUKT DER KLASSE 1 LASERSTRAHLEN NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN LASERPRODUKT DER KLASSE 2 SWEDISH / SVENSKA KLASS 1 KLASS 2 LASERPRODUKT KLASS 1 LASERLJUS STIRRA INTE MOT STRLEN LASERPRODUKT KLASS 2 CHINESE / 1 2 1
2 JAPANESE /
KOREAN /
Power Supply Use only a Symbol approved power supply 50-14000-101R output rated 9 Vdc and minimum 1 A. The power supply is certified to EN60950-1 with SELV outputs. Use of an alternative power supply invalidates any approval given to this device and may be dangerous. Batteries Please follow the local regulations when disposing of re-chargeable batteries. Taiwan - Recycling EPA (Environmental Protection Administration) requires dry battery producing or importing firms in accordance with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper battery disposal. Quick Reference Guide 11 Symbol Rechargeable Batteries Symbol rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations to how long a battery can operate or be stored before needing replacement. Many factors affect the life of a battery pack such as heat, cold, customer usage profiles, age, and severe drops. When batteries are stored over a year, battery cell manufacturers advise that some irreversible deterioration in overall battery quality may occur. To minimize this loss, they recommend storing batteries half charged in a dry, cool place between 41 and 77F (5 and 25C), the cooler the better) and removed from the equipment to prevent the loss of capacity. Batteries should be charged to half capacity at least once a year. If an electrolyte leakage is observed, avoid any contact with the affected area and properly dispose of the battery. Replace the battery when a significant loss of run time is detected. Batteries must be charged within the 32 to 104F (0 to 40C) temperature range. The standard warranty period for all Symbol batteries is 30 days, regardless if the battery was purchased separately or included as part of the mobile computer. For more information on Symbol batteries, please visit http://mysymbolcare.symbol.com/battery/batbasics1.html. Radio Frequency Interference Requirements-FCC Tested to comply with FCC Standards FOR HOME OR OFFICE USE Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected.
- Consult the dealer or an experienced radio/TV technician for help. Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radio Frequency Interference Requirements - Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Radio Transmitters This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical specifications were met. 12 PL370/470 Cradle Marking and European Economic Area (EEA) 2.4GHz devices for use through the EEA have the following restrictions:
- Maximum radiated transmit power of 10 mW EIRP in the frequency range 2.400 -2.4835 GHz
France, equipment is restricted to 2.446 -2.454 GHz frequency range Italy requires a user license for outside usage. Statement of Compliance Symbol Technologies, Inc., hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from http://www2.symbol.com/doc/. Brazil Declaraes Regulamentares para P370, P470 PL370 y PL470 BRAZIL NOTA: A marca de certificao se aplica ao Equip. de Radiao Restrita, model P470 y PL470. Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio."
Para maiores consultas sobre ANATEL consulte o site: www.anatel.gov.br The following signifies approval in Brazil. Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Symbol for recycling. For information on how to return product, please go to:
http://www.symbol.com/environmental_compliance. Dansk: Til kunder i EU: Alle produkter skal returneres til Symbol til recirkulering, nr de er udtjent. Ls oplysningerne om returnering af produkter p:
http://www.symbol.com/environmental_compliance. Deutsch: Fr Kunden innerhalb der EU: Alle Produkte mssen am Ende ihrer Lebensdauer zum Recycling an Symbol zurckgesandt werden. Informationen zur Rcksendung von Produkten finden Sie unter http://www.symbol.com/environmental_compliance. Eesti: EL klientidele: kik tooted tuleb nende eluea lppedes tagastada taaskasutamise eesmrgil Symbol'ile. Lisainformatsiooni saamiseks toote tagastamise kohta klastage palun aadressi:
http://www.symbol.com/environmental_compliance. Espaol: Para clientes en la Unin Europea: todos los productos debern entregarse a Symbol al final de su ciclo de vida para que sean reciclados. Si desea ms informacin sobre cmo devolver un producto, visite: http://www.symbol.com/environmental_compliance. Quick Reference Guide 13 Franais : Clients de l'Union Europenne : Tous les produits en fin de cycle de vie doivent tre retourns Symbol pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.symbol.com/environmental_compliance. Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Symbol al fine di consentirne il riciclaggio. Per informazioni sulle modalit di restituzione, visitare il seguente sito Web: http://www.symbol.com/environmental_compliance. Magyar: Az EU-ban vsrlknak: Minden tnkrement termket a Symbol vllalathoz kell eljuttatni jrahasznosts cljbl. A termk visszajuttatsnak mdjval kapcsolatos tudnivalkrt ltogasson el a http://www.symbol.com/environmental_compliance weboldalra. Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Symbol te worden teruggezonden voor recycling. Raadpleeg http://www.symbol.com/environmental_compliance voor meer informatie over het terugzenden van producten. Portugus: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos Symbol para reciclagem. Para obter informaes sobre como devolver o produto, visite:
http://www.symbol.com/environmental_compliance. Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku ivljenjske dobe vrniti podjetju Symbol za reciklao. Za informacije o vrailu izdelka obiite:
http://www.symbol.com/environmental_compliance. Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrtettvksi Symbol-yhtin, kun tuotetta ei en kytet. Listietoja tuotteen palauttamisesta on osoitteessa http://www.symbol.com/environmental_compliance. Svenska: Fr kunder inom EU: Alla produkter som uppntt sin livslngd mste returneras till Symbol fr tervinning. Information om hur du returnerar produkten finns p http://www.symbol.com/environmental_compliance. 14 PL370/470 Cradle Wall Mounting Template 1.27 Wall Mounting Socket 1 Center Line of Cradle 3.85 Use 1/8 drill bit for screw holes. Wall Mounting Socket 2 Quick Reference Guide 15 This page is intentionally blank. Service Information Before you use the unit, it must be configured to operate in your facilitys network and run your applications. If you have a problem running your unit or using your equipment, contact your facilitys Technical or Systems Support. If there is a problem with the equipment, they will contact the Symbol Support Center:
United States United Kingdom Australia Denmark/Danmark France 1-800-653-5350 0800 328 2424 1-800-672-906 7020-1718 01-40-96-52-21 905-629-7226 337-6588 01-5055794-0 9 5407 580 6074-49020 Canada Asia/Pacific Austria/sterreich Finland/Suomi Germany/
Deutschland Mexico/Mxico Norway/Norge Spain/Espaa Europe/Mid-East Distributor Operations 5-520-1835
+47 2232 4375
+913244000 Contact local distributor or call
+44 118 945 7360 Italy/Italia Netherlands/Nederla nd South Africa Sweden/Sverige 2-484441 315-271700 11-809 5311 08 445 29 00 Latin America Sales Support Inside USA: 1-800-347-0178;
Outside USA: +1.954.255.2610 For the latest version of this guide go to: http://www.symbol.com/manuals. 72-38494-01 Revision C - May 2006 Symbol Technologies, Inc. One Symbol Plaza Holtsville, N.Y. 11742-1300 http://www.symbol.com