DataData Sheet Sheet Module nameIA9QH5 S83D-F Version 0.1 Feb. 27, 2019 Syncomm Technology Corp. 10F., No. 101, Sec. 2, Gongdao 5th Rd., East Dist., Hsinchu City, Taiwan, R.O.C. Tel: +886-3-5169188 Fax: +886-3-5169111 http://www.syncomm.com.tw SYNCOMM Confidential E-Mail: sell@syncomm.com.tw Web site: Http://www.syncomm.com.tw INDEX 1. Features....................................................................................................................................................3 2. Application.............................................................................................................................................. 3 3. RF Specification...................................................................................................................................... 4 4. Electrical Specification............................................................................................................................4 5. Mechanical Specification.........................................................................................................................6 6. Block Diagram....................................................................................................... 7. Interface...................................................................................................................................................8 8. Revision History......................................................................................................................................8 This document is proprietary and confidential to Syncomm Technology Corp. SYNIC and Intelligent Wireless are trademarks of Syncomm Technology Corp. All other trademarks and registered trademarks are the property of their respective owners. SYNCOMM Confidential E-Mail: sell@syncomm.com.tw Web site: Http://www.syncomm.com.tw 1. Features IA9QH5 S83D-F MODULE page - 3 -
5.2GHz/5.8GHz ISM Band GFSK modulation Low BOM cost Long distance > 30m (Line of sight) Support 1-1 duplex mode or 1-N broadcasting mode Digital I2S audio interface Support no audio detection function Support compression/un-compression mode Short delay time variation Antenna diversity Audio format 16/24bit , 32/44.1/48K/96KHz sampling rate Robust Packet error correction No RF induced audio noise Audio latency time < 20ms Low power consumption
(Programmable according customized spec.) 2. Application Wireless HTiB Rear Speaker Wireless Outdoor Speaker Wireless TV theater Wireless Audio Sender Wireless Headphone Wireless Stereo Ear Microphone SYNCOMM Confidential E-Mail: sell@syncomm.com.tw Web site: Http://www.syncomm.com.tw IA9QH5 S83D-F MODULE page - 4 -
3. RF Specification Item Channel Range
-20dB bandwidth RF Output Power Sensitivity Item Channel Range
-20dB bandwidth RF Output Power Sensitivity Min 5160 Min 5735 Typ 2.7 12
-91 Max Unit 5240 MHz MHz dBm dBm Note 2M Mode Peak power at Antenna port The smaller, the better Table 1 5.2GHz RF Specification Typ 3 12
-90 Max Unit 5840 MHz MHz dBm dBm
-
Note 2M Mode Peak power at Antenna port The smaller, the better Table 2 5.8GHz RF Specification Electrical Specification Typ 3.3 25 Min 3.0 0 4. Item Power Supply Voltage Operating Temperature Consumption Current
(TX_MODE) Consumption Current
(RX_MODE) 130 86 Max 3.6 55 Unit V mA mA Note RF Power :11dBm ,0.1CH No GPIO driving Item Symbol VIH VIL VOH VOL Min Parameter 2.0 Input High Threshold
-0.3 Input Low Threshold 2.4 Output High Threshold Output Low Threshold SYNCOMM Confidential E-Mail: sell@syncomm.com.tw Web site: Http://www.syncomm.com.tw Table 3 Typ Table 4 Max 3.33 0.8 0.4 Unit V V V V Conditions LDO_OUT=3V LDO_OUT=3V LDO_OUT=3V LDO_OUT=3V Power On Reset Characteristics Parameter Symbol Trst IA9QH5 S83D-F MODULE page - 5 -
Min Typ Max 10 Unit mS Table 5 Conditions Fig 4.1 Reset Timing Chart SYNCOMM Confidential E-Mail: sell@syncomm.com.tw Web site: Http://www.syncomm.com.tw IA9QH5 S83D-F MODULE page - 6 -
5. Mechanical Specification 5.1 No Shielding Case Dimension20 * 40 * 6.7 mm PCB 4 Layers Mechanical Drawing Fig 5.1 Mechanical Drawing of S83D-F Module Propose 1.27mm Female Header sizeH:4.30.15mm W:3.00.15mm SYNCOMM Confidential E-Mail: sell@syncomm.com.tw Web site: Http://www.syncomm.com.tw IA9QH5 S83D-F MODULE page - 7 -
5.2 With Shielding Case Dimension20 * 40 * 8.7 mm PCB 4 Layers Mechanical Drawing Fig 5.2 Mechanical Drawing of S83D-F Module with shielding case Propose 1.27mm Female Header sizeH:4.30.15mm W:3.00.15mm SYNCOMM Confidential E-Mail: sell@syncomm.com.tw Web site: Http://www.syncomm.com.tw 6. Interface Fig 7.1 Pin sequence of S83D-F Module (Bottom View) IA9QH5 S83D-F MODULE page - 8 -
Name SPB_I2S_MCLK Pin 1 VCCIO 2 DGND 3 4 GPIO 32 5 GPIO 14 6 GPIO 13 7 GPIO 17 8 GPIO 26 9 I2C_CLK 10 I2C_DATA 11 DGND 12 DGND 13 GPIO 27 14 GPIO 21 15 GPIO 16 16 GPIO 0 17 M_RESET(PORN) 18 I2C_CLK 19 I2C_DATA 20 GPIO 30 21 SPA_I2S_DATA 22 SPB_I2S_LRCK 23 DGND 24 SPB_I2S_BCK 25 GPIO 15 26 SPB_I2S_DATA Resistor clock output TX Function Define RX Function Define DC 3.0 ~ 3.6V IN Digital GND SPB I2S audio MCLK system clock output AMP MUTE GPIO GPIO GPIO I2C_BUSYNeed 10K Pull High Resistor I2C Master/Slave clock signal I2C Master/Slave data signal Digital GND Digital GND Pairing GPIO ON/OFF 12V I/O P DC 3.0 ~ 3.6V IN P Digital GND I/O SPB I2S audio MCLK system I/O GPIO I/O GPIO I/O GPIO I/O GPIO I/O I2C_BUSYNeed 10K Pull High I/O I2C Master/Slave clock signal I/O I2C Master/Slave data signal P Digital GND P Digital GND I/O GPIO I/O GPIO I/O GPIO I/O GPIO / SAP I2S audio MCLK GPIO / SAP I2S audio MCLK I/O Internal power on reset (1) I/O I2C Master/Slave clock signal I/O I2C Master/Slave data signal I/O GPIO I/O I2S DATA 0 I/O SPB I2S audio LRCK P Digital GND I/O SPB I2S audio BCK I/O GPIO I/O SPB I2S audio Data Internal power on reset (1) I2C Master/Slave clock signal I2C Master/Slave data signal AMP RESET(L Act) SYNC LED SPB I2S audio LRCK Digital GND SPB I2S audio BCK ON/OFF 3.3V SPB I2S audio Data Table 6 IO Function Define Note : (1)
*.Not need external RC circuit to do RC reset
*.Power On Reset Characteristics can reference section 5 Electrical Specification (page 6)
*.External controller can direct control M_RESET but should assign the control IO as input for normal operation and output low to Reset S83D-E Module Revision History 7. Date 2019/02/27 Revision 0.1 Descriptions First release Table 7 SYNCOMM Confidential E-Mail: sell@syncomm.com.tw Web site: Http://www.syncomm.com.tw FCC Statement 15.19 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 15.21 Note: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment. 15.105(b) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS The RF 5G Wireless Module complies with Part 15 of the United States of America FCC rules and regulations. The Orig inal Equipment Manufacturer (OEM) must comply with the FCC certification requirements. 15.21 Any changes or modifications made to the module without the manufacturers approval could void the users authority to operate the module. Regulatory Module Integration Instructions This module has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC/ISED
(Innovation, Science and Economic Development Canada) certification if they meet the following conditions. Otherwise, Additional FCC/IC approvals must be obtained. The OEM must comply with the FCC labeling requirements. If the modules label is not visible when installed, then an additional permanent label must be applied on the outside of the finished product which states: Contains transmitter module FCC ID: PJH-IA9QH5S83D-F. Additionally, the following statement should be included on the label and in the final products user manual:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interferences, and (2) this device must accept any interference received, including interference that may cause undesired operation. The users manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC / IC RF exposure guidelines. The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. This Module is full modular approval, it is limited to OEM installation ONLY. The module is limited to installation in mobile application. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si brouillage est susceptible d'en compromettre le fonctionnement. le IC 20cm RF This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. Cet quipement est conforme aux limites dexposition aux rayonnements de la IC tablies pour un environnement non contr. Cet quipement doit tre install et fonctionner au moins 20 cm de distance dun radiateur ou de votre corps.