FCC ID: YOR-WRX560 Synology 11ax router

Synology 11ax router Hardware Installation Guide Table of Contents Chapter 1: Before You Start Package Contents Synology WRX560 at a Glance LED Indicator Table Hardware Specification Safety Instructions Chapter 2: Hardware Setup Adjust Antennas Position Your WRX560 Connect to Your WRX560 Mount Your WRX560 Set up Synology Router Manager (SRM) 3 4 5 6 7 8 8 9 10 11 Synology_HIG_WRX560_20220603 2 Before You Start Thank you for purchasing this Synology product! Before setting up your new expansion unit, please check the package contents to verify that you have received the items below. Also, make sure to read the safety instructions carefully to avoid harming yourself or damaging your expansion unit. Chapter 1 Note: All images below are for illustrative purposes only, and may differ from the actual product. Package Contents Main unit x 1 AC power adapter x 1 RJ-45 LAN cable x 1 3 Synology WRX560 at a Glance No. Article Name Location Description 1 2 3 4 5 6 7 8 9 STATUS Indicator Displays the status of the system. WAN Indicator Wi-Fi Indicator WPS Button Front Panel Displays the status of WAN connection. Displays the status of Wi-Fi connection. Press to start WPS. Wi-Fi Button Right Panel Press for three seconds to turn on/off the Wi-Fi network. USB 3.2 Gen 1

(Type-A) Port Power Button Power Port WAN Port 10 2.5G WAN/LAN Port 11 12 LAN Port RESET Button Connect an external drive, USB printer, or other types of USB devices here. Press to power on/off the Synology Router. Connect the AC power adapter here. Connect a network cable from the ISP modem into this port to establish WAN connection. 1. Connect a network cable from the ISP modem into this port to Rear Panel establish WAN connection. 2. Connect network cables into these ports to establish LAN connection Connect network cables into these ports to establish LAN connection. Press and hold for four seconds (Soft Reset) or for ten seconds

(Hard Reset). 4 Chapter 1: Before You Start LED Indicator Table LED Indicator Color Green Status Static Blinking Description Powered on System Ready Status Indicator Orange Static System booting/Rebooting/Hard Reset Blinking Mesh network disconnected Green/Orange Blinking Searching device Wi-Fi WAN Green Green Off Off Off Static Blinking Static Blinking Powered off Wi-Fi active WPS connecting No Wi-Fi Network connected Data transmitting Network disconnected 5 Chapter 1: Before You Start Hardware Specification Item External Ports WAN Port LAN Ports Size (H x W x D) (mm) Weight (kg) Supported Clients

(for SRM management) RT6600ax USB 3.2 Gen 1 (Type-A) x 1 Gigabit WAN x 1 Gigabit WAN x 1 and 2.5G WAN x 1 (Dual WAN) Gigabit LAN x 3 and 2.5G LAN x 1 Gigabit LAN x 3 (Dual WAN) 233 x 194 x 66 1 kg Windows 7 onwards Mac OS 10.12 onwards File Systems External: EXT4, EXT3, FAT, NTFS, HFS+

Wireless Standards 2.4GHz: 802.11 b/g/n/ax 5GHz: 802.11 a/n/ac/ax 802.11ax (2.4GHz): Up to 600 Mbps Operating Frequency Range 802.11ax (5GHz): Up to 2400 Mbps Wireless Operation Modes Wireless Security Wireless Router Wireless AP (Access Point) WPS support WPA2-Personal WPA/WPA2-Personal WPA2-Enterprise WPA/WPA2-Enterprise Opportunistic Wireless Encryption (OWE) WPA3-Personal WPA3-Enterprise WPA2/WPA3-Personal Antennas 2T2R Omni-directional high-gain dipole (2.4GHz) 4T4R Omni-directional high-gain dipole (5GHz) Buttons & Switches Power WPS Wi-Fi On/Off Reset Language Localization Line voltage: 100V to 240V AC Frequency: 50/60Hz Environment Requirements Operating Temperature: 40 to 104F (5 to 40C) Storage Temperature: -5 to 140F (-20 to 60C) Relative Humidity: 5% to 95% RH Note: Model specifications are subject to change without notice. Please refer to www.synology.com for the latest information. 6 Chapter 1: Before You Start Safety Instructions Keep away from direct sunlight and away from chemicals. Ensure a stable environment with no abrupt changes in temperature or humidity. Place the unit right side up at all times. Keep the unit away from liquids. Before cleaning, unplug the power cord. Do not use chemical or aerosol cleaners. Wipe with damp paper towels. To prevent the unit from falling over, do not place it on carts or any unstable surfaces. The power cord must plug into the correct supply voltage. Ensure the supplied AC voltage is correct and stable. Warning, electric shock hazard. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries appropriately. Power cord must be plugged into a socket-outlet with earthing connection. Keep body parts away from moving fan. This product must be installed by qualified personnel in a restricted access location (like dedicated equipment rooms, service closets). 7 Chapter 1: Before You Start Hardware Setup Position Your WRX560 Chapter 2 For optimal performance, it is recommended to position your WRX560 as advised below:

On a stable surface (e.g. an elevated shelf) away from any possible physical interruptions. Close to the center of the area where the wired/wireless client devices are placed, and within a visible distance from the wireless devices. In a position where few walls and ceilings are between your WRX560 and its client devices. Away from any potential electrical signal sources, such as other Wi-Fi routers, 3G/4G bases, and microwave ovens. Away from large expanses of metal or other materials, such as metal doors, glass panels, and concrete. 8 Connect to Your WRX560 1 Use the included network cable to connect your WRX560 (at the WAN1 port) to the ISP modem. Connect one end of the power adapter to the power port on your WRX560, and the other end to the power outlet. Press the power button to power on your WRX560. Wait for up to two minutes until the STATUS and WAN LED indicators turn green. 2 Connect wireless client devices to your WRX560. When the Wi-Fi indicator has turned static green, WRX560 is ready to connect with other devices. Use your wireless device to scan and join the Wi-Fi network created by your WRX560. Note:

The default credentials for the Wi-Fi network:

Wi-Fi SSID: Synology_(Serial) Password: synology You can change it during the initial SRM setup. 9 Chapter 2: Hardware Setup 10 Chapter 2: Hardware Setup 3 Connect wired client devices to your WRX560. Use network cables to connect devices to the LAN ports. The corresponding LAN LED indicators should turn orange/green to indicate successful connection. Mount Your WRX560 Do not install the device in an unstable location, such as on an unsteady table or an inclined surface. Do not place another hub or object that generates heat on top of this unit. Please route all cables properly to prevent people from tripping over them. Ensure the air vents on the product are not blocked by other equipment or walls. Only use the power cable included with the product. Using other power cables may result in damage or fire. Use 2 screws (not included) with the dimensions shown below. The screw head should project out from the wall at 7mm. 11 Chapter 2: Hardware Setup Set up Synology Router Manager (SRM) 1 Use a computer or wireless device connected to your WRX560 's local network. If you use a wireless device, scan and join the Wi-Fi network (SSID: Synology_(Serial); Password: synology). 2 Open a web browser, and enter either URL into the address bar:

http://router.synology.com http://192.168.1.1:8000 3 Once connected, click Start to launch the SRM Setup Wizard. 4 Fill in the information to set up the administrator account. Click Next to continue. 5 Fill in the information to set up the Wi-Fi network. Click Next to continue. 12 Chapter 2: Hardware Setup 6 Set up the operation mode. When choosing the Wireless Router mode, you can also enable External access to SRM so that only external access via the HTTP(S) port (e.g. 8000/8001) can reach SRM. 7 Choose an Internet connection type:

PPPoE: Choose this option if you have obtained PPPoE credentials from the ISP. Manual IP: Choose this option if you have obtained an available IP address for use. Auto IP: Choose this option if you rely on an ISP modem for automatic IP assignment. 8 The wizard will continue to set up your WRX560, and it may take up to three minutes to complete the setup. 13 Chapter 2: Hardware Setup 9 After the setup is complete, click Start managing now to enjoy SRM and its various features. Note:

1. Above is a general demonstration of the SRM setup steps. The steps and available options may somewhat vary depending on your device type (e.g. PC or wireless device), access type (LAN, WAN, or Wireless LAN), and chosen operation mode (Wireless Router or Wireless AP). 2. If the setup is to be completed with a wireless device, remember to download DS router to manage your RT3000ax from anywhere. 14 Chapter 2: Hardware Setup Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. FCC regulations restrict the operation of this device to indoor use only. Industry Canada statement:

This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. Avertissement:

Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) lorsquil y a lieu, les types dantennes (sil y en a plusieurs), les numros de modle de lantenne et les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, nonce la section 6.2.2.3, doivent tre clairement indiqus Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis plus de 20 cm entre le radiateur et votre corps. RED Compliance Statement Compliance with 2014/53/EU Radio Equipment Directive (RED) In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency bands used and the maximum RF transmit power of the product for sale in the EU:

Frequency Range

(MHz) 2412 ~ 2472 5180 ~ 5320 5500 ~ 5700 Max. Transmit Power (dBm) EIRP 19.93 dBm 22.87 dBm 29.83 dBm This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. AT EE IT PT BE FI LV RO BG FR LT SK HR DE LU SI CY EL MT ES CZ HU NL SE DK IE PL UK UK(NI) This device is restricted to indoor use

Synology 802.11ax fA ER es Model(#%) : WRX560 DC Input (@A) :+12V ===2.5A FCC ID:YOR-WRX560 L IC: 20954-WRX560 CAN ICES-003(B)/NMB-003(B) ReNZ

[RJ 020-220012

=r, [1220003020 S Indoor Use Only E UK Y& ZOWRIBAICSUT OMERAETT Cc D33A87 9F., No.1, Yuandong Rd., Bangiao Dist., RoHS Ml New Taipei City 220632 Taiwan This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made in Taiwan BSG X000OOXKKKKKXKKK

Synology Inc. 8/5/2022 To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Short Term Confidentiality Request for FCC ID: YOR-WRX560 To Whom It May Concern:

Pursuant to sections 0.457 and 0.459 of CFR 47, and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 [_] or 180 [X] days; or for a specified date of [J /LI/LJ not to exceed 180 days from the Grant Date. See KDB 726920.

- eg. User Manual

- eg, External Photos

- e.g. Internal Photos

- eg. Test Setup photos The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Client's signature: ite Chan Clients name & title: Mike Chen/Product Manager Contact address: 9F., No.1, Yuandong Rd., Banqiao Dist., New Taipei City 220632 Telephone Number: +886229551814#8207 Fax Number: N/A Email: mchen@synology.com Synology Inc. 8/5/2022 To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: YOR-WRX560 Pursuant to sections 0.457 and 0.459 of CFR 47, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application as:

- eg. Block Diagram

- e.g. Schematics

- e.g. Operational Description

- e.g. SDR software and security information The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Clients signature: Marke Chev Clients name & title: Mike Chen/Product Manager Contact address: 9F., No.1, Yuandong Rd., Banqiao Dist., New Taipei City 220632 Telephone Number: +886229551814#8207 Fax Number: N/A Email: mchen@synology.com

Synology Inc, OF., No.1, Yuandong Rd., Banqiao Dist., New Taipei City 220632 Date: 8/17/2022 UNII Device Declaration Letter To whom it may concern:

We have declared below featured for FCC equipment authorization, Device FCC !D : YOR-WRX560

(1) DFS Device -- Ml Master , [[] Client with Radar detection capability ,

(7) Client without radar detection capability , [] N/A

(2) Active / Passive Scanning , adhoc mode access point capability

(3)

(4)

(6) Frequency Band Active Scanning passive scanning Ad Hoc Mode Access point

(MHz) (the device can (where the device is capability capability transmit a probe can listen only with no

(beacon)) probes) 5150-5250 Wi Yes , _] No C1 Yes , BNo []Yes,MBNo | MlYes,(]No 5250-5350 Wi Yes , LI No (] Yes , MENo C[1Yes, No | MlYes,[-]No 5470-5725 I Yes , No (1 Yes , MI No []Yes,MENo | MiYes, (No 5725-5850 Mi Yes , -] No [-] Yes , MINo []Yes,MBNo | MlYes,(] No 5850-5895 Hi Yes, No L] Yes , MNo L]Yes,M@No | MlYes,[_] No Country code selection ability - [-] Yes , HI No If no, pls explain how it was implemented :

Meet 15.202 requirement - Mf Yes , [[] No, pls check below :

HBA master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices L_]A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer.

[-] Apply , No Apply , (\fapply , pis help to provide explanation on it was implement , and how software was controlled) Indoor devices:

[_] Clients 1) Client device (EUT) will not directly connect to another client device. 2) Client device (EUT) will only associate and connect with an indoor Access Point (AP) or indoor Subordinate. 3) Client device (EUT) will always be under the control of an indoor AP. However, there may exist situations where the client may transmit brief messages, prior to being under the control of an AP, to join an AP network. But these brief messages will only ccur if the client has detected a signal confirming that an AP is operating on a particular channel. These brief messages will have a time-out mechanism if the client does not receive a response from an AP.

[_] Subordinates 1) No direct connection to internet 2) Prohibited for control of or communications with unmanned aircraft systems including drones. 3) Supplied power from a wired connection and has no batteries. 4) Indoor installation only. i Access Points 1) Supplied power from a wired connection and has no batteries. 2) Indoor installation only. Signature : Juke Cher Name / Title : Mike Chen/Product Manager Contact address: 9F., No.1, Yuandong Rd., Bangiao Dist., New Taipei City 220632 Telephone Number: +886229551814#8207 Fax Number: N/A Email: mchen@synology.com

Synology Inc. 9F., No.1, Yuandong Rd., Banqiao Dist., New Taipei City 220632 WIFI Channel 12 & 13 Declaration Letter To whom it may concern :

We have declared below featured for FCC equipment authorization in regard to 802.11b/g/n channel 12 & 13 operating capability for FCC ID : YOR-WRX560 Please check C] Product hardware does not have the capability to operate on channel 12 & 13 Product hardware has the capability to operate on channel 12 & 13. V However , these 2 channels will be disabled via software and user will not able to enable these 2 channels Product hardware has the capability to operate on channel 12 & 13. O And meeting KDB 594280 DO1 requirement. Pls explain detail here. oO Others Pls explain detail here. DATE : August 8, 2022 Signature JNWve Chan FCC grantee contact person information. Name/Title: Mike Chen/Product Manager Company Name: Synology Inc. Address: 9F., No.1, Yuandong Rd., Banqiao Dist., New Taipei City 220632 Tel: +886229551814#8207 Email: mchen@synology.com

Synology Inc, Declaration of Authorization We Name: Synology Inc. Address: OF, No. 1, Yuandong Rd., Bangiao Dist. City: New Taipei State:

Country: Taiwan Declare that Name Representative of agent: William Chung / Senior Director Agent Company name: A Test Lab Techno Corp. Address: No. 140-1, Changan Street, Bade District, City: Taoyuan Country: Taiwan Is authorized to apply for Certification of the following product(s) Product Name: Synology l1ax router FCCID: YOR-WRX560 IC: 20954-WRX560 Trademark: Synology on our behalf This is valid until December 31, 2022, or until FCC and IC certification are completed, whichever comes sooner. Date: August 5, 2022 City: New Taipei Name: Mike Chen/Product Manager Signature: Mike Cho"