DJI Pro Wireless Receiver User Guide In the Box DJI Pro Wireless Receiver1 Antenna1 Introduction is designed to be used with the DJI Force Pro, DJI Master Wheels The DJI Pro Wireless Receiver and other controllers, providing a max operation range of 3 km. It is operating at dual-frequency 2.4 GHz and 5.8 GHz and compatible with the Ronin 2, Ronin-S and a third-party gimbal through an S-Bus connection. 1. Antenna Relays control signals. Do not obstruct the antenna. 2. Operating Frequency Switch The operating frequency can be switch from 2.4GHz and 5.8GHz. Please note that some regions are not supported 5.8GHz, make sure the switch is toggled to the 2.4GHz. 3. Link Button Press and hold this button for two seconds to start linking to the controller. 4. Status LED Indicates the status of system. 5. Power and Communication Port Connect this port to gimbal using the CAN Bus cable, D-Bus and S-Bus cable. 6. S-Bus/CAN Switch Toggle the switch to CAN position when using with Ronin 2 and Ronin-S, toggle the switch to S-
Bus position when using with an S-Bus gimbal. 7. USB-C Port For activation and firmware updating. 8. 1/4-20 Mounting Hole For fixing the receiver in place. 9. M4 Mounting Hole For fixing the receiver in place. Installation It is recommended to fix the wireless receiver at a place that without signal interference through the mounting hole on the receiver or using other tools. Cable Connections 1. Connect to Ronin 2: connect the Power and Communication Port to the Ronin 2 accessory power ports above the pan motor using the CAN Bus cable. 2. Connect to Ronin-S: connect the Power and Communication Port to the Ronin-S CAN port using a CAN cable (sold separately) 3. Connect to an S-Bus supported gimbal connect the Power and Communication Port to the gimbals S-Bus port. Keep the Antennas vertical during using, and make sure there is no obstructions and interference between the devices. Activation and Linking Activation is required when use the Wireless Receiver for the first time. To activate, connect the USB port to the DJI Pro Assistant for Ronin. Press and hold on the link button for two seconds to link to a controller. The Status LED indicates the status of system, refer to the table below for details. Status LED Descriptions Patterns Blinks red quickly Solid red Blinks red slowly Solid green Blinks green slowly Specifications Descriptions The device is not activated. The device is activated and not linked to a controller. The device is linking. Operating at 2.4 GHz Operating at 5.8 GHz Dimensions 633819 mm Operating Environment Temperature -20 to 50 Operating Frequency 2.4 GHz, 5.8 GHz Input Voltage 5 V-15 V Compliance Information FCC Compliance Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RSS Warning This device complies with ISEDC licence
-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'ISEDC applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure Information This equipment complies with FCC/ISEDC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC /ISEDC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. Cet quipement est conforme aux limites d'exposition aux radiations FCC / ISEDC dfinies pour un environnement non contr?l. Afin d'viter la possibilit de dpasser les limites d'exposition aux radiofrquences FCC / ISEDC, la proximit humaine de l'antenne ne doit pas tre infrieure 20 cm pendant le fonctionnement normal. KCC Warning Message
. NCC Warning Message EU Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance EU contact address: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany Co., Ltd. por la presente declara que Declaracin de cumplimiento UE: SZ DJI Osmo Technology este dispositivo cumple los requisitos bsicos y el resto de provisiones relevantes de la Directiva 2014/53/EU. Hay disponible online una copia de la Declaracin de conformidad UE en compliance www.dji.com/euro-
Direccin de contacto de la UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany EU-verklaring van overeenstemming: SZ DJI Osmo Technology Co., Ltd. verklaart hierbij dat dit apparaat voldoet aan de essentile vereisten en andere relevante bepalingen van Richtlijn 2014/53/EU. De EU-verklaring van overeenstemming is online beschikbaar op www.dji.com/euro-compliance Contactadres EU: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany Co., Ltd. declara, atravs deste Declarao de conformidade da UE: A SZ DJI Osmo Technology documento, que este dispositivo est em conformidade com os requisitos essenciais e outras disposies relevantes da Diretiva 2014/53/EU. Existe uma cpia da Declarao de conformidade da UE disponvel online em compliance www.dji.com/euro-
Endereo de contacto na UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany Dichiarazione di conformit UE: SZ DJI Osmo Technology Co., Ltd. dichiara che il presente dispositivo conforme ai requisiti essenziali e alle altre disposizioni rilevanti della direttiva 2014/53/EU. Una copia della dichiarazione di conformit UE disponibile online all'indirizzo Web www.dji.com/euro-compliance Indirizzo di contatto UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany Dclaration de conformit UE : Par la prsente, SZ DJI Osmo Technology Co., Ltd. dclare que cet appareil est conforme aux principales exigences et autres clauses pertinentes de la directive europenne 2014/53/EU. Une copie de la dclaration de conformit UE est disponible sur le site www.dji.com/euro-
compliance Adresse de contact pour l'UE : DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany EU-Compliance: Hiermit erklrt SZ DJI Osmo Technology Co., Ltd., dass dieses Gert den wesentlichen Anforderungen und anderen einschlgigen Bestimmungen der EU-Richtlinie 2014/53/EU entspricht. Eine Kopie der EU-Konformittserklrung finden Sie online auf www.dji.com/euro-compliance. Kontaktadresse innerhalb der EU: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Environmentally friendly disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances. Thailand Warning message Mexico Warning message La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Brazil Warning message Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a interferncia sistemas operando em carter primrio UAE logo requirements The characters shall appear in black print against a white background. No character shall be less than 2mm in height. The letters TRA shall be atleast 3mm in height.