DJI RS 3 Mini Quick Start Guide V1.0 2022.8 Introduction DJI RS 3 Mini is a professional single-handed 3-axis gimbal specifically designed for DSLR and mirrorless cameras. Users can calibrate the gimbal and set parameters on the screen and use the onboard buttons to control the gimbal and switch profiles and working modes. When used with the provided camera control cables, DJI RS 3 Mini can also control the camera focus, shutter, and recording. The grip has a built-in battery. After connecting to the Ronin app, it is easy to control gimbal movement and parameter settings with intelligent functions. 1. Roll Motor 2. Touchscreen 3. Joystick 4. Grip
(Built-in battery with 1/4-20 screw hole) 5. Tilt Motor 6. Pan Lock 7. Power PortUSB-C 8. Power Button 9. M Button 10. Camera Control Button 11. Tilt Lock 12. Roll Lock 13. Pan Motor 14. Front Dial 15. Trigger Getting Started 1. Downloading the DJI Ronin App 2. Charging the gimbal via the USB-C port on the grip. 3. Attaching the Tripod. 4. Power On: Press and hold on the power button to power on the gimbal. Mounting the camera Mount the camera onto the gimbal. 1. Attach the Upper Quick-Release Plate. 2. Attach the Lower Quick-Release Plate and lens support. 3. Attach the camera to the gimbal. Balancing 1. Balancing the vertical tilt a. Unlock the tilt axis, and loosen the mounting plate knob. b. Rotate the tilt axis so that the camera lens is pointing upward. Check to make sure the camera is not top or bottom-heavy. If top-heavy, move the camera backward. If bottom-heavy, move the camera forward. c. Tighten the knob. The vertical tilt is balanced until the camera is steady while pointing upward. 2. Balancing depth for the tilt axis a. Rotate the tilt axis so that the camera lens is pointing forward. Toggle the lever to the unlocked position. b. Check to make sure the camera is not front or back-heavy. If front-heavy, move the camera backward by turning the knob. If back-heavy, move the camera forward. c. Toggle the lever to the locked positon. The Tilt axis is balanced if the camera is steady while tilting up or down for 45 degrees. d. Lock the tilt axis. 3. Balancing the roll axis a. Unlock the roll axis. Toggle the lever on the roll arm to the unlocked positon. b. Check the direction in which the roll motor swings. If the camera rotates to the left, move the camera to the right. If the camera rotates to the right, move the camera to the left. c. Toggle the lever on the roll arm to the locked positon. The roll axis is balanced if the camera is steady. d. Lock the roll axis. 4. Balancing the pan axis a. b. Unlock the pan axis. Toggle the lever on the pan arm to the unlocked positon. Hold the grip, tilt the camera forward, and adjust the pan arm to parallel to you. Check the movement of the pan axis. If the camera lens rotates to the left, push the pan axis to the right. If the camera lens rotates to the right, push the pan axis to the left. c. Toggle the lever on the pan arm to the locked positon. The pan axis is balanced if the camera is steady when rotating the pan while lifting the grip. Operation Touch Screen After installation, activation, and balancing, DJI RS 3 Mini must be auto-tuned before it can be used. Home: tap gimbal calibration to start Auto Tune, and check the balance status, select follow mode and follow speed by tapping the icons. Slide down to set system settings, and slide up to enter joystick and front wheel settings page. Button Feature Power Button: press and hold the power button to turn on or off. Trigger: press once to start ActiveTrack. press and hold the trigger to enter Lock mode. Press twice to recenter the gimbal. M Button: tap to select a user profile. Press and hold to enter Sport mode. Press and hold while press twice on the trigger to stay in Sport mode. Press twice to enter portrait mode. Press three times to enter Roll 360. Press and hold the M button which holding on the trigger to begin auto tune. Camera Control Button: after connecting the camera control port and camera, press halfway for autofocus, as you would the shutter button on a camera. Press to start or stop recording. Press and hold to take a photo. Joystick: push the joystick up or down to control the movement of the tilt axis, and push it left or right to control the movement of the pan axis. Go to the Joystick page of the Ronin app to adjust the parameters for the pan, tilt, and roll axes. Front Dial: turn the dial to control focus or gimbal movements (feature depends on the dial settings). Firmware Update If new firmware is available, you will be notified by the Ronin app. Update the firmware according to the on-screen instructions. Do not power off the gimbal or exit the app during the firmware update. The Ronin app will prompt if the update is successful. If the update fails, restart the gimbal and Ronin app, and try again. Notes:
Make sure the gimbal has sufficient power before updating. Ensure the mobile phone is connected to the internet when updating. Do not power off the gimbal when updating. The axis locks will lock automatically when the update starts. It is normal for the axis locks to lock or unlock during the process. Battery Usage Notes 1. DJI RS 3 Mini is powered by a built-in battery through the grip. Users take full responsibility for all operations and usage. 2. The grip should be used in temperatures from -10 to 45 C (14 to 113 F). Use of the grip in environments above 50 C (122 F) can lead to a fire or explosion. Use of the grip in environments where the temperature is below 0 C (32 F) can significantly reduce operation time. 3. DO NOT disassemble or pierce the grip in any way or the battery may leak, ignite, or explode. 4. DO NOT drop or strike batteries. DO NOT place heavy objects on the grip or charger. 5. DO NOT heat batteries. DO NOT put the grip in a microwave oven or in a pressurized container. Specifications Model Input Power USB Input P20M ModelHB7-2450mAh-7.2 Type18650 Li-ion 2S Capacity2450mAh Energy17.64Wh Voltage5V-2V 5V/2A Bluetooth Operating Frequency 2.4000 GHz -2.4835 GHz Bluetooth Transmitter Power
<4 dBm Operating Temperature
-10C to 45C Compliance Information FCC Compliance Notice Suppliers Declaration of Conformity Product name: DJI RS 3 Mini Model Number: P20M Responsible Party: DJI Technology, Inc. Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502 Website: www.dji.com We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. ISED Compliance Notice CAN ICES-003 (B) / NMB-003(B) This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference. (2)This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1)Lappareil ne doit pas produire de brouillage; (2)Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the CNR-102. Cet quipement est conforme aux limites dexposition aux rayonnements RSS-
102 tablies pour un environnement non contrl. Lutilisateur final doit suivre les instructions spcifiques pour satisfaire les normes. Cet metteur ne doit pas tre co-implant ou fonctionner en conjonction avec toute autre antenne ou transmetteur. Le dispositif portatif est conu pour rpondre aux exigences dexposition aux ondes radio tablie par le dveloppement nergtique DURABLE. To view the full compliance information, slide down on the camera view, tap the setting icon, and scroll through to select Compliance Info. Pour voir les informations compltes de conformit, balayez vers le bas sur la vue camra, appuyez sur licne de paramtres et slectionnez Infos de Conformit.