Ronin RavenEye Image Transmission SystemUserGuide Model:WV001 Introduction The Ronin RavenEye Image Transmission System is used to transmitthe image signal to the DJI RS/RS2/RSC/RSC2,mobilephoneandmonitor,andmoredevice,itiseasytochecktheliveview remotely. 1. Antenna Transmitthewirelesssignal. 2. ReservedLED Reserved. 3. Power/CommunicationPort(USBC) Forchargingandcommunication. 4. HDMIPort ForconnectingthecamerasHDMIport. 5. RSSCameraControlPort(USBC) 6. BatteryLevelIndicators 7. Indicatesthebatterylevel. StatusLED Indicatesthesystemstatus. 8. PowerButton Forconnectingtothegimbalscameracontrolport. Press and hold to power on/off. Press four times to restore the default WiFi password to 12345678. 9. ColdShoe Forconnectingtothegimbalorcamera. Installation 1. AttachtheImageTransmissionSystemtothegimbalorcamera. 2. ConnecttheHDMIporttothecamerasHDMIportusingtheprovidedHDMIcableaccording 3. ConnectthecommunicationporttothegimbalsImageTransmissionportusingtheprovided tothecameratype. USBCtoUSBCcable. 4. ConnectthecameracontrolporttothegimbalsRSScameracontrolport. 5. Balancethecameraafterinstallation.Refertothegimbalsusermanualfordetails. Usage Poweronthegimbal,cameraandtheImageTransmissionSystem.TheStatusLEDindicatesthe currentstatus. LEDStatus Description Notconnected SolidRed SolidBlue SolidGreen HDMIandWiFiconnected HDMIconnected,orWiFiconnectedwithDJIRoninappconnected. WhenusedwiththeDJIRS2/DJIRSC2,thetouchscreen(DJIRS2only)andthemobiledeviceare able to display the camera view.With the Image Transmission System, ActiveTrack can be used. Youcanalsocontrolthegimbalviamobilephone. Whenused with the DJI RS/DJI RSC, ActiveTrack and camera control are unavailable, other operationsarethesame. Whenusedwiththecamerawithoutagimbal,usethemobilephonetocontrolthecameraand displaythecameraview. Specifications OperationFrequency Weight Dimensions 2412-2462MHz5745-5825MHz 126g 82mmx63mmx24mm FCC/ISEDC Compliance Notice This device complies with Part 15 of the FCC/ISEDC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC/ISEDC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This device has been tested and meets the FCC/ISEDC SAR limits. This equipment should be installed and operated with minimum distance 5mm between the radiator&
human. ISED Compliance Notice Ce dispositif est conforme la partie 15 des rgles FCC/ISEDC. Lopration est soumise aux deux conditions suivantes : (1) Cet appareil ne peut pas causer dinterfrences nocives et (2) Cet appareil doit accepter toute interfrence reue, y compris toute interfrence susceptible de provoquer un fonctionnement indsirable. Toute modification ou modification non expressment approuve par la partie responsable de la conformit pourrait annuler le pouvoir de lutilisateur dexploiter lquipement. Cet quipement a t test et sest avr conforme aux limites dun appareil numrique de classe B, conformment la partie 15 des rgles de la FCC/ISEDC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nocives dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de lnergie par radiofrquence et, sil nest pas install et utilis conformment aux instructions, peut causer des interfrences nocives aux communications radio. Toutefois, il ny a aucune garantie que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement cause des interfrences nuisibles la rception de la radio ou de la tlvision, qui peuvent tre dtermines en teignant et en allumant lquipement, lutilisateur est encourag essayer de corriger linterfrence par une ou plusieurs des mesures suivantes :
Rorienter ou dplacer lantenne de rception. Augmenter la sparation entre lquipement et le rcepteur. Connecter lquipement une prise sur un circuit diffrent de celui auquel le rcepteur est connect. Consultez le concessionnaire ou un technicien expriment en radio/tlvision pour obtenir de laide. Exposition aux RF Aprs examen de ce matriel aux conformit aux limites DAS et/ou aux limites d les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes. Ce matriel devrait tre install et convient une distance minimale de 5 mm intensit de champ RF, entre le radiateur et l'homme