FCC ID: SS3-GL3001501 C1

There are two options for Dynamic Home Point. 1. Set the aircraft current coordinate as the new Home Point. 2. Set the mobile device's coordinate as the new Home Point. Setting Up Dynamic Home Point Follow the steps below to setup Dynamic Home Point:

1. Connect to the mobile device and launch the DJI Pilot app and go to the Camera page.

, to set the mobile devices coordinates as the new Home Point. 2. Tap and select 3. Tap and select

, to set the aircrafts coordinates as the new Home Point. 4. The aircraft status indicator blinks green to show Home Point is set successfully. Vision Positioning System DJI Vision Positioning is a positioning system that uses ultrasonic and image data to help the aircraft identify its current position. With the help of Vision Positioning, your Phantom 3 Professional can hover in place more precisely and fly indoors or in other environments where there is no GPS signal available. The main components of DJI Vision Positioning are located on the bottom of your Phantom 3 Professional, including [1] one monocular camera and [2]two sonar sensors.

[1]

[2]

Using Vision Positioning Vision Positioning is activated automatically when the Phantom 3 Professional is powered on. No manual action is required. Vision Positioning is typically used in the indoor environment where no GPS is available. By using the sensors on the Vision Positioning system, Phantom 3 Professional can perform precision hovering even when no GPS is available. 2015 DJI. All Rights Reserved. 15 AircraftPhantom 3 Professional User Manual Follow the steps below to use Vision Positioning:

1. Toggle the switch to P mode. 2. Place the aircraft on a flat surface. Notice that the Vision Positioning system cannot work properly on surfaces without pattern variations. 3. Power on the aircraft. The aircraft status indicator will flash twice in green light, which indicates the Vision Positioning system is ready. Gently push the throttle up to lift off, and the aircraft will hover in place. The performance of your Vision Positioning System is subject to the surface you are flying over. The ultrasonic waves may not be able to accurately measure the distance over sound absorbing materials, and the camera may not function correctly in suboptimal environments. The aircraft will switch from P mode to A mode automatically if both GPS and Vision Positioning System are not available. So operate the aircraft cautiously when in any of the following situations:

Flying over monochrome surfaces (e.g. pure black, pure white, pure red, pure green). Flying over a highly reflective surfaces. Flying at high speeds(over 8 m/s at 2 meters or over 4 m/s at 1 meter). Flying over water or transparent surfaces. Flying over moving surfaces or objects. Flying in an area where the lighting changes frequently or drastically. Flying over extremely dark (lux < 10) or bright (lux > 100,000) surfaces. Flying over surfaces that can absorb sound waves (e.g. thick carpet). Flying over surfaces without clear patterns or texture. Flying over surfaces with identical repeating patterns or textures (e.g. tiles with same design). Flying over inclined surfaces that will deflect sound waves away from the aircraft. Keep the sensors clean at all times. Dirt or other debris may adversely affect the effectiveness of the sensors. The effective hovering altitudes of the aircraft is from 0 to 3 meters. Vision Positioning system may not function properly when the aircraft is flying over water. Vision Positioning system may not be able to recognize pattern on the ground in low light conditions (less than 100 lux). Do not use other ultrasonic devices with frequency of 40 KHz when Vision Positioning system is in operation. Vision Positioning system may not be able to stabilize the aircraft when flying close to the ground (below 0.5 meters) in fast speed. Keep the animals away from the aircraft when Vision Positioning system is activated. The sonar sensor emits high frequency sound that is only audible to some animals. Flight Recorder Flight data is automatically recorded to the SD card. This includes flight telemetry, aircraft status information, and other parameters. Access these data from the DJI Pilot app through the Aircraft Micro-USB Port. Attaching and Detaching the Propellers Use only DJI approved propellers with your Phantom 3 Professional. The grey or black nut on the propeller indicates the rotation direction of the propeller and where it should be attached. To attach 16 2015 DJI. All Rights Reserved. AircraftPhantom 3 Professional User Manual the propellers properly, match the nut with the axis on the motors of your Phantom 3 Professional. Propellers Figure Attach On Legends Grey cap Black cap Motors with a grey axis Motors with a black axis Lock : Turn the propellers in the indicated direction to mount and tighten Unlock : Turn the propellers in the indicated direction to loosen and remove Attaching the Propellers 1. Attach the propellers with a grey nut onto a motor with the grey axis and spin the propellers clockwise to secure them in place. Attach the propellers with a black nut onto a motor with the black axis and spin the propellers counter clockwise to secure its position. Be sure to completely tighten each propeller by hand before flight. Ensure propellers are attached to its corresponding motors, otherwise the aircraft cannot take off. Wear gloves when handling propellers. Manually tighten each of the propellers on the corresponding motors to ensure it is attached firmly. Detaching the Propellers Hold the motor still. Then spin the propeller in the unlock direction indicated on the propeller itself. Check that the propellers and motors are installed correctly and firmly before every flight. Ensure that all propellers are in good condition before each flight. DO NOT use aged, chipped, or broken propellers. To avoid injury, STAND CLEAR of and DO NOT touch propellers or motors when they are spinning. ONLY use original DJI propellers for a better and safer flight experience. DJI Intelligent Flight Battery The DJI Intelligent Flight Battery has a capacity of 4480 mAh, voltage of 15.2 V, and smart charge-

discharge functionality. It can only be charged with an appropriate DJI approved charger. 2015 DJI. All Rights Reserved. 17 AircraftPhantom 3 Professional User Manual Flight Intelligent Flight Battery Charger Battery must be fully charged before using it for the first time. Refer to "Charging the Intelligent Flight Battery" for more information . Be aware that the output power of the supplied Phantom 3 Professional charger is 100W. DJI Intelligent Flight Battery Functions 1. Battery Level Display: LEDs display the current battery level. 2. Battery Life Display: LEDs display the current battery power cycle. 3. Auto-discharging Function: The battery automatically discharges to below 65% of total power when it is idle for more than 10 days to prevent swelling. It takes around 2 days to discharge the battery to 65%. It is normal to feel moderate heat emitting from the battery during the discharge process. Dis-

charge thresholds can be set in the DJI Pilot app. 4. Balanced Charging: Automatically balances the voltage of each battery cell when charging. 5. Over charge Protection: Charging automatically stops when the battery is fully charged. 6. Temperature Detection: The battery will only charge when the temperature is between 0C(32F) and 40C (104F). is detected. 7. Over Current Protection: Battery stops charging when high amperage (more than 8 A) is detected. 8. Over Discharge Protection: Discharging automatically stops when the battery voltage reaches 12 V to prevent over-discharge damage 9. Short Circuit Protection: Automatically cuts the power supply when a short circuit is detected. 10. Battery Cell Damages Protection: DJI Pilot app shows warning message when damaged battery cell 11. Battery Error History Browse the battery error history from the DJI Pilot app. 12. Sleep Mode: Sleep mode is entered after 20 minutes of inactivity to save power. 13. Communication: Battery voltage, capacity, current, and other relevant information is provided to the aircrafts to the main controller. Refer to Disclaimer and Intelligent Flight Battery Safety Guidelines before use. Users take full responsibility for all operations and usage. Using the Battery LED1 LED2 LED3 LED4 Power Button (Bulit-in LED) Battery Level Indicators Powering ON/OFF Powering On: Press the Power Button once, then press again and hold for 2 seconds to power on. The Power LED will turn red and the Battery Level Indicators will display the current battery level. Powering Off: Press the Power Button once, then press again and hold for 2 seconds to power off. 18 2015 DJI. All Rights Reserved. AircraftPhantom 3 Professional User Manual Low Temperature Notice:

1. Battery capacity is significantly reduced when flying in low temperature environment (< 0C ). 2. It is not recommended to use the battery in extremely low temperature (< -10C) environment. Battery voltage should reach to the appropriate level when using in the environment where temperature range between minus 10C to 5C. 3. Stop flying when DJI Pilot app displays Low Battery Level Warning in low temperature environment. 4. Place the battery indoors to warm up the battery before using it in the low temperature environment. 5. To ensure the performance of the battery, keep the battery body temperature above 20C. In cold environments, insert the battery into the battery compartment and allow the aircraft to warm up for approximately 1-2 minutes before taking off. Checking the battery level The Battery Level Indicators display how much remaining power the battery has. When the battery is powered off, press the Power Button once. The Battery Level Indicators will light up to display the current battery level. See below for details. The Battery Level Indicators will also show the current battery level during charging and discharging. The indicators are defined below.

: LED is on.

: LED is off.

: LED is flashing. Battery Level LED1 LED2 LED3 LED4 Battery Level 87.5%~100%

75%~87.5%

62.5%~75%

50%~62.5%

37.5%~50%

25%~37.5%

12.5%~25%

0%~12.5%

=0%

Battery life The battery life indicates how many more times the battery can be discharged and recharged before it must be replaced. When the battery is powered off, press and hold the Power Button for 5 seconds to check the battery life. The Battery Level Indicators will light up and/or blink as described below for 2 seconds:

2015 DJI. All Rights Reserved. 19 AircraftPhantom 3 Professional User Manual Battery Life LED1 LED2 LED3 LED4 Battery Life 90%~100%

80%~90%

70%~80%

60%~70%

50%~60%

40%~50%

30%~40%

20%~30%

below 20%

When battery life reaches 0%, it can no longer be used. For more information about the battery, launch DJI Pilot app and check the information under the battery tab. Charging the Intelligent Flight Battery 1. Connect Battery Charger to a power source (100-240 V 50/60 Hz). 2. Open the Protection Cap and connect the Intelligent Flight Battery to the Battery Charger. If the battery level is above 95%, turn on the battery before charging. 3. The Battery Level Indicator will display the current battery level during charging. 4. The Intelligent Flight Battery is fully charged when Battery Level Indicators are all off. 5. Air cool the Intelligent Flight Battery after each flight. Allow its temperature to drop to room temperature before storing it for an extended period. Always turn off the battery before inserting it or removing it from the Phantom 3 Professional. Never insert or remove a battery when it is powered on. Intelligent Flight Battery Charger Power Outlet 20 2015 DJI. All Rights Reserved. AircraftPhantom 3 Professional User Manual LED1 Battery Level Indicators while Charging LED3 LED2 LED4 Battery Level 0%~25%

25%~50%

50%~75%

75%~100%

Fully Charged Charging Protection LED Display The table below shows battery protection mechanisms and corresponding LED patterns. Battery Level Indicators while Charging LED1 LED2 LED3 LED4 Blinking Pattern Battery Protection Item LED2 blinks twice per second Over current detected LED2 blinks three times per second Short circuit detected LED3 blinks twice per second Over charge detected LED3 blinks three times per second Over-voltage charger detected LED4 blinks twice per second Charging temperature is too low LED4 blinks three times per second Charging temperature is too high After any of the above mentioned protection issues are resolved, press the button to turn off the Bat-

tery Level Indicator. Unplug the Intelligent Flight Battery from the charger and plug it back in to resume charging. Note that you do not need to unplug and plug the charger in the event of a room temperature error, the charger will resume charging when the temperature falls within the normal range. DJI does not take any responsibility for damage caused by third-party chargers. How to discharge your Intelligent Flight Battery:

Slow : Place the Intelligent Flight Battery into the Phantom 3 Professionals Battery Compartment and power it on. Leave it on until there is less than 8% of power left, or until the battery can no longer be turned on. Launch the DJI Pilot app to check battery levels. Rapid : Fly the Phantom 3 Professional outdoors until there is less than 8% of power left, or until the battery can no longer be turned on. 2015 DJI. All Rights Reserved. 21 AircraftPhantom 3 Professional User Manual Remote Controllers This chapter describes the features of the remote controller that includes, how to operate the aircraft and camera. 22 2015 DJI. All Rights Reserved. Remote Control Remote Controller Profile The Phantom 3 Professional remote control is a multi-function wireless communication device that in-

tegrates the video downlink ground system and aircraft remote control system. The video downlink and aircraft remote control system operate at 2.4 GHz. The remote controller features a number of camera functions, such as taking and previewing photos and video, and controlling gimbal motions. The remote controller is powered by a 2S rechargeable battery. The current battery level is displayed by LEDs on the front panel of the remote control. Compliance Version: The remote control is compliant with both CE and FCC regulations. Operating Mode: Control can be set to Mode 1 , Mode 2. Mode 1: The right stick serves as the throttle. Mode 2: The left stick serves as the throttle. Do not operate more than 3 aircrafts within in the same area (size equivalent to a soccer field) to prevent transmission interference. Remote Controller Operations Powering On and Off the Remote Controller The Phantom 3 Professional remote controller is powered by a 2S rechargeable battery with a capacity of 6000 mHA. The battery level is indicated by the Battery Level LEDs on the front panel. Follow the steps below to power on your remote controller:

1. When powered off, press the Power Button once and the Battery Level LEDs will display the current battery level. 2. Press and hold the Power Button to power on the remote controller. 3. The remote controller beeps when it is powered on. The Status LED will blink green rapidly, indicating that the remote controller is linking to the aircraft. The Status LED will show a solid green light when linking is complete. 4. Repeat step 2 to power off the remote controller. Charging Remote Controller Charge the remote controller via supplied charger. Refer to the figure below for more details. 2015 DJI. All Rights Reserved. 23 Remote Controllers Power Outlet Charger Power Button Controlling Camera Shoot videos or images and adjust camera settings via the Shutter Button, Camera Settings Dial, Play-

back Button and Video Recording Button on the remote control.

[5]

[4]

[1]

[2]

[3]

[1] Camera Settings Dial Turn the dial to quickly adjust camera settings such as ISO, shutter speed, and aperture without letting go of the remote controller. Move the dial button to left or right to view the pictures or videos in playback mode.

[2] Playback Button Press to view images or videos that have already been captured.

[3] Shutter Button Press to take a photo. If burst mode is activated, multiple photos will be taken with a single press.

[4] Recoding Button Press once to start recording video, then press again to stop recording.

[5] Gimbal Dial Use this dial to control the tilt of the gimbal. Controlling Aircraft This section explains how to control the orientation of the aircraft through the remote controller. The Remote Control is set to Mode 2 by default. 24 2015 DJI. All Rights Reserved. Remote ControllersPhantom 3 Professional User Manual Stick Neutral/ mid point: Control sticks of the Remote Control are placed at the central position. Move the Stick: The control stick is pushed away from the central position. Remote Control

(Mode 2) Aircraft indicates nose direction)

(

Remarks Moving the left stick up and down changes the aircrafts elevation. Push the stick up to ascend and down to descend. Push the throttle stick up to takeoff. When both sticks are centered, the Phantom 3 Professional will hover in place. The more the stick is pushed away from the center position, the faster the Phantom 3 Professional will change elevation. Always push the stick gently to prevent sudden and unexpected elevation changes. Moving the left stick to the left or right controls the rudder and rotation of the aircraft. Push the sick left to rotate the aircraft counter clock-wise, and push the stick right to rotate the aircraft clockwise. If the stick is centered, the Phantom 3 Professional will stay facing its current direction. The more the stick is pushed away from the center position, the faster the Phantom 3 Professional will rotate. Moving the right stick up and down changes the aircrafts forward and backward pitch. Push the stick up to fly forward and down to fly backward. Phantom 3 Professional will hover in place if the stick is centered. Push the stick further away from the center position for a larger pitch angle (maximum 30) and faster flight. Moving the right stick control left and right changes the aircrafts left and right pitch. Push left to fly left and right to fly right. The Phantom 3 Professional will hover in place if the stick is centered. Push the stick further away from the center position for a larger pitch angle (maximum 30) and faster flight. Gimbal Dial: Turn the dial to the right, and the camera will shift to point upwards. Turn the dial to the left, and the camera will shift to point downwards. The camera will remain in its current position when dial is static. 2015 DJI. All Rights Reserved. 25 Remote ControllersPhantom 3 Professional User Manual Flight Mode Switch Toggle the switch to select the desired flight mode. You may choose between; P mode, F mode and A mode. Position Position 1 Position 2 Position 3 Figure Flight Mode F mode A mode P mode Position 1 Position 2 Position 3 P mode (Positioning) : P mode works best when GPS signal is strong. There are three different states of P mode, which will be automatically selected by the Phantom 3 Professional depending on GPS signal strength and Vision Positioning sensors:

P-GPS: GPS and Vision Positioning both are available, and the aircraft is using GPS for positioning. P-OPTI: Vision Positioning is available but the GPS signal is not. Aircraft is using only Vision Positioning for hovering P-ATTI: Neither GPS or Vision Positioning available, aircraft is using only its barometer for positioning, so only altitude is controlled. A mode (Attitude): GPS and Vision Positioning System is not used for stabilization. The aircraft only uses its barometer to stabilize. The aircraft can automatically return home if remote control signal is lost if the Home Point is recorded successfully. F mode (Function): Intelligent Orientation Control (IOC) is activated in this mode. For more information about IOC, refer to the IOC in Appendix. The Flight Mode Switch is locked in P mode by default. To unlock the switch, launch the DJI Pilot app, enter the Camera page, tap MODE, and then activate Multiple Flight Mode . RTH button Press and hold this button to start the Return to Home (RTH) procedure. The LED around the RTH Button will blink white to indicate the aircraft is entering RTH mode. The aircraft will then return to the last recorded Home Point. Press this button again to cancel the RTH procedure and regain the control of the aircraft. 26 2015 DJI. All Rights Reserved. Remote ControllersPhantom 3 Professional User Manual Connecting Mobile Device Tilt the Mobile Device Holder to the desired position. Press the button on the side of the Mobile Device Holder to release the clamp, and then place your mobile device into the clamp. Adjust the clamp to secure your mo-

bile device. Then connect your mobile device to the remote controller with a USB cable. Plug one end of the cable into your mobile device, and the other end into the USB port on the back of the remote controller. Optimal Transmission Range The signal transmission between aircraft and remote controller perform best within the range that dis-

played in the picture shown below:

Optimal Transmission Range strong weak Ensure the aircraft is flying within the optimal transmission range. Adjust the distance and position between the operator and the aircraft to achieve optimal transmission performance. Remote Controller Status LED The Status LED reflects connection status between remote control and aircraft. The RTH LED shows the Return to Home status of the aircraft. The table below contains details on these indicators. Status LED RTH LED 2015 DJI. All Rights Reserved. 27 Remote ControllersPhantom 3 Professional User Manual Status LED Alarm chime chime Slow Blinking Red D-D-D...... Solid Red Solid Green Remote Controller Status The remote controller is disconnected from the aircraft. The remote controller is connected with the aircraft. Remote controller error.

/

Red and Green/ Red and Yellow Alternate Blinks RTH LED Solid White Blinking White Blinking White None Sound chime D . DD .. . . HD downlink is disrupted. Remote Controller Status Aircraft is returning home. Sending Return to Home command to the aircraft. Aircraft Return to Home in progress. The Remote Status Indicator will blink red, sound an alert, when the battery level is critically low. Linking the Remote Controller The remote controller is linked to your aircraft before delivery. Linking is only required when using a new remote controller for the first time. Follow these steps to link a new remote controller:

1. Power on the remote controller and connect to the mobile device. Launch DJI Pilot app. 2. Power on the Intelligent Flight Battery. 3. Enter Camera view and tap on and then tap Linking RC button as shown below. RC Control Setting RC Calibration Stick Mode Default stick mode is Mode 2, changing stick modes alters the way the aircraft is controlled. Do not change unless familiar with your new mode. C1 Battery info C2 Battery info You can customize the C1 and C2 buttons on the back of the RC. Linking RC 28 2015 DJI. All Rights Reserved. Remote ControllersPhantom 3 Professional User Manual 4. The remote controller is ready to link. The Remote Controller Status Indicator blinks blue and "beep"

sound is emitted. RC Control Setting RC Calibration Stick Mode Default stick mode is Mode 2, changing stick modes alters the way the aircraft is controlled. Do not change unless familiar with your new mode. timeout in 54 seconds Press the linking button on the aircraft Searching for aircraft frequency, to link this remote controller C1 Battery info C2 Cancel Battery info You can customize the C1 and C2 buttons on the back of the RC. Linking RC 5. Locate the Linking button on the side of the aircraft, as shown in the figure shown below. Press the Linking button to start linking. The LED to the left of the linking button blinks green to indicate that the aircraft is ready to link, and it blinks solid green when linking is complete. The Remote Controller Status Indicator will display solid green if Link is succeed. Linking Button Remote controller will disconnect from the linked aircraft if a new remote controller is linked to the same aircraft. Remote Controller Compliance Version The remote controller is compliant with both CE and FCC requirements. 2015 DJI. All Rights Reserved. 29 Remote ControllersPhantom 3 Professional User Manual Gimbal Camera This chapter provides the technical specifications of the camera, explains the operating mode of the gimbal. 30 2015 DJI. All Rights Reserved. Camera and Gimbal Camera Profile The on-board camera supports 4K video capture up to 4096 x 2160p24 and 12M pixel photos capture by using the 1/2.3 inch CMOS sensor. You may export the video in either MOV or MP4 format for editing. Available picture shooting modes include burst, continuous, and time-lapse mode. A live preview of what the camera is seeing before you shoot videos and pictures is supported through the DJI Pilot App. Camera Micro-SD Card Slot To store your photos and videos, plug in the Micro-SD card into the slot shown below before powering on the Phantom 3 Professional. The Phantom 3 Professional comes with a 16 GB Micro-

SD card and supports up to a 64 GB Micro-SD card. A UHS-1 type Micro-SD card is recommended, because of the fast read and write capability of these cards enables you to store high-resolution video data. Do not remove Micro-SD card from the Phantom 3 Professional when it is powered on. Camera Data Port Power on the Phantom 3 Professional and then connect a USB cable to the Camera Data Port to down-

load photos or videos from the camera to your computer. Power on the aircraft before attempting to access the files on the Micro-SD card. 2015 DJI. All Rights Reserved. 31 Gimbal Camera Camera Operation Use the Shutter and Record button on the remote controller to shoot the images or the videos through the DJI Pilot app. For more information about how to use these buttons, refer to Controlling Camera. Gimbal Gimbal Profile The 3-axis Gimbal provides a steady platform for the attached camera, allowing you to capture stabilized images and video. The Gimbal can tilt the camera up to 120 degrees. 30 0

-90 Use the gimbal dial on the remote controller to control pitch movement of the camera by default. Note that you cannot control the pan movement of the camera by default. Gimbal Operation Modes Two Gimbal operation modes are available. Switch between the different operation modes on the Camera page of the DJI Pilot App. Note that your mobile device must be connected to the remote controller for changes to take effect. Refer to the table below for details:

Follow Mode FPV Mode The angle between Gimbals orientation and aircrafts nose remains constant at all times. One user alone can control the pitch motion of the gimbal. The Gimbal will lock to the movements of the aircraft to provide a First-

Person-View flying experience. Gimbal motor error may occur in these situations: (1) Gimbal is placed on uneven ground. (2) Gimbal has received an excessive external force, e.g. a collision. Please take off from flat, open ground and protect the gimbal after powering up. Flying in heavy fog or cloud may make the gimbal wet, leading to a temporary failure. The gimbal will recover when it dries out. 32 2015 DJI. All Rights Reserved. Gimbal CameraPhantom 3 Professional User Manual Anti-drop Kit The Anti-drop Kit helps keep the gimbal and camera connected to the aircraft. Two have been mounted on delivery. If new ones are required, take the gimbal and press part [1] through the center hole of the Vibration Absorber the center hole of part [2]. Lock them together as shown in [3]. Mounting the Anti-drop Kit diagonally is recommended. 2015 DJI. All Rights Reserved. 33 Gimbal CameraPhantom 3 Professional User Manual DJI Pilot App This chapter introduce the four main sections of the DJI Pilot app. 34 2015 DJI. All Rights Reserved. DJI Pilot App The DJI Pilot app is a mobile app designed specifically for the Phantom 3 Professional. Use this app to control the gimbal, camera and other features of your flight system. The app also comes with Map, Acad-

emy and User Center, for configuring your aircraft and sharing the photos and videos with your friends. It is recommended that you use a tablet for the best experience. United States Mountain View CAMERA MAP ACADEMY USER CENTER Camera The Camera page contains a live HD video feed from the Phantom 3 Professionals camera. You can also configure various camera parameters from the Camera page.

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

MODE P-GPS CL Safe to Fly (GPS) ISO 100 1/320 EV 0 4821 JPEG 00:22:16 4K 30

[9]

[10]

[11]

H:

2M D:

39M V.S 8.3 M/S H.S 24.2 M/S 1.2M

[12]

0 0 200m 200m 2015 DJI. All Rights Reserved. 35

[16]

[15]

[14]

[13]

DJI Pilot App [1] Flight Mode

: The text next to this icon indicates the current flight mode. Tap to enter MC (Main Controller) Settings. Modify flight limits, perform compass calibration, and set the gain values.

: This icon shows the current strength of GPS signals. Green bars indicates adequate GPS

[2] GPS Signal Strength strength.

[3] IOC Settings

: This icon shows which IOC setting that the aircraft has entered when in F Mode. Tap to enter IOC setting menu and select the desired IOC setting.

[4] System Status

: This icon shows current aircraft system status, such as GPS signal health.

[5] Battery Level Indicator

: The battery level indicator dynamically displays the battery level. The color zones on the battery level indicator represent different battery levels.

[6] Remote Controller Signal

: This icon shows the strength of remote controller signal.

[7] HD Video Link Signal Strength controller.

: This icon shows the HD video downlink signal strength between the aircraft and the remote

[8] Battery Level

: This icon shows the current battery level. Tap to enter battery information menu, set the various battery warning thresholds and view the battery warning history in this page.

[9] General Settings

: Tap this icon to enter General Settings page. Select parameter metric, reset the camera, enable the quick view feature, adjust the gimbal pitch value and toggle flight route display on this page.

[10] Camera Operation Bar Shutter shooting.

: Tap this button to take a single photo. Press and hold this button to select burst or time-lapsed Record

: Tap once to start recording video, then tap again to stop recording. You can also press the Vid-

eo Recording Button on the remote controller, which has the same function. Playback

: Tap to enter playback page. You can preview photos and videos as soon as they are 36 2015 DJI. All Rights Reserved. DJI Pilot App Phantom 3 Professional User Manual captured. Camera Settings Advance or Manual mode.

: Tap to enter the camera exposure value setting. User may switch from Auto exposure mode to

[11] Map Display the flight path of the current mission. Tap to switch from the Camera GUI to the Map GUI. 0 0 200m 200m

[12] Vision Positioning

: This icon shows the distance between the surface and the Vision Positioning System's sensors.

[13] Flight Telemetry Vision Positioning Status Icon is highlighted when Vision Positioning is in operation. Flight attitude is indicated by the flight attitude icon.

(1) The red arrow shows which direction the aircraft is facing.

(2) Light blue and dark blue areas indicate pitch.

(3) Pitching of the boundary between light blue and dark blue area shows roll angle.

[14] Return to Home (RTH)

: Initiate RTH home procedure. Tap to have the aircraft return to the last recorded home point. 2015 DJI. All Rights Reserved. 37 DJI Pilot App Phantom 3 Professional User Manual [15] Auto Takeoff/Landing

/

: Tap to initiate auto takeoff or landing.

[16] Back

: Tap to return to the main GUI. 38 2015 DJI. All Rights Reserved. DJI Pilot App Phantom 3 Professional User Manual Map User can view the current flight route in a larger map view in this page. You can also perform Auto takeoff and Landing in the page. Ensure your mobile device has access to the Internet. Due to the map data required, Wi-Fi connection is recommended. Internet access is required to cache the map, if Wi-Fi is unavailable, mobile data service is required. Academy Download user manual, view tutorial videos and practice your flight skills using the simulator in this page. You can also use FilmMaker to create and edit the video clips captured by the aircraft. User Center You can sync the picture and videos to the mobile device, view the flight records and check your DJI account status in the User Center. Use the DJI registered account to login to the User Center. 2015 DJI. All Rights Reserved. 39 DJI Pilot App Phantom 3 Professional User Manual Flight This chapter describes the flight safety and flight restrictions. 40 2015 DJI. All Rights Reserved. Flight Once pre-flight preparation is complete, it is recommended to use the flight simulator in the DJI Pilot App to practice the flight skills and learn to fly safely. Ensure that all flights are carried out in a wide open area. Flight Environment Requirements 1. Do not use the aircraft in severe weather conditions. These include wind speed exceeding 10 m/s , snow, rain and smog. GPS signal. 2. Only fly in open areas. Tall and steel structures may affect the accuracy of the on-board compass and 3. Avoid approaching the obstacles, crowds, high voltage power lines, trees or bodies of water. 4. Minimize electromagnetic interference by not flying in the area with high levels of electromagnetism, including base stations or radio transmission towers. 5. Aircraft and battery performance is subject to environment factor such as air density and temperature. Be very careful when flying 19, 685 feet (6000 m) or more above sea level as battery and aircraft per-

formance may be affected. 6. The Phantom 3 Professional cannot operate within the polar areas. Flight Limits and Flight Restriction Area All unmanned aerial vehicle (UAV) operators should abide by all regulations from such organizations as the ICAO (International Civil Aviation Organization), FAA and their own national airspace regulations. For safety reasons, the flight limits function is enabled by default to help users use this product safely and legally. The flight limits function includes height limits, distance limits and No Fly Zones. When operating in P Mode, height, distance limits and No Fly Zones work together to manage flight. In A mode only height limits work and flights cannot go higher than 1640 feet (500 m) . Maximum flight altitude & Radius Limits Maximum flight altitude & Radius limit flying height and distance, and the user may change these settings in the DJI Pilot App. For Be aware that, the maximum flight altitude value cannot exceed 1640 feet (500 m). Once complete, your Phantom 3 Professional will fly in a restricted cylinder that is determined by these settings. The tables below show the details of these limits. Maximum Flight Altitude Max Radius Home Point Height of aircraft when powered on 2015 DJI. All Rights Reserved. 41 Flight GPS Signal Strong Maximum Flight Altitude Max Radius Blinking Green Flight Limits Aircraft's altitude cannot exceed the specified value. DJI Pilot App Warning: Height limit reached. Aircraft Status Indicator None. Flight distance must be within the max radius. Warning: Distance limit reached. Rapid red flashing when close to the max radius limit. GPS Signal Weak Blinking Yellow Flight Limits DJI Pilot App Aircraft Status Indicator Maximum Flight Altitude Max Radius No limits Flight height restricted to 1640 feet (500 m) and under. Warning: Height limit reached. None. If you fly out of the limit, you can still control the Inspire, but cannot fly it further. If the Inspire flies out of the max radius in Ready to Fly (non-GPS) mode, it will fly back within range automatically. Flight Restriction of Restricted Areas Restricted areas include airports worldwide. All restricted areas are listed on the DJI official website at http://www.dji.com/fly-safe/category-mc. Restricted areas are divided into category A and category B. Category A areas cover major international airport such as LAX and Heathrow and no-drone zones, while category B areas includes smaller airports. Category A Safety Zone

(1) The category A safety zone is comprised of a small no-fly zone and a range of restricted-altitude zones. Flight is prevented in the no-fly zone but can continue with height restrictions in the restrict-

ed-altitude zone.

(2) A radius of R1 miles (km) around a designated safety zone is a no-fly zone, inside which takeoff is prevented. The value of R1 is determined by the size of the airport.

(3) From R1 to R1 + 1 miles (R1 + 1.6 km) around restricted areas are altitude restricted, with maximum altitude going from 66 feet (20 m) at R1 miles to 1640 feet (500 m) at R1 + 1 miles (R1 + 1.6 km).

(4) A warning zone has been set around the safety zone. When you fly within 320 feet (100m) of the safety zone, a warning message will appear on the DJI Pilot App. 42 2015 DJI. All Rights Reserved. FlightPhantom 3 Professional User Manual Safety Zone 66 feet 1 mile R1 320 feet R2 1640 feet 1640 feet 66 feet 1 mile R1 320 feet R2 Category B Safety Zone

(1) Category B safety zone is comprised of a no-fly zone and a warning zone.

(2) R mile around the safety zone is a designated no-fly zone. The value of R is determined by the size of the airport.

(3) A warning zone has been set around the safety zone. When you fly within 0.6 miles (1 km) of this zone, a warning will appear on the DJI Pilot App. 100m R 100m R 2015 DJI. All Rights Reserved. 43 FlightPhantom 3 Professional User Manual GPS Signal Strong Blinking Green Zone Restriction DJI Pilot App Prompt No-fly Zone Restricted-

altitude flight zone Motors will not start. If the aircraft enters the restricted area in A mode but P mode activates the aircraft will automatically descend to land then stop its motors after landing. If the aircraft enters the restricted area in A mode but P mode activates, it will descend to a safe altitude and hover 15 feet (4.5 m) below the safe altitude. Warning zone No flight restriction applies, but there will be warning message. Warning: You are in a No-fly zone. Take off prohibited. Warning: You are in a No-fly zone, automatic landing has begun. (aircraft is entering the area within R1 radius) Warning: You are in a restricted zone. Descending to safe altitude. (If you are between the range of R1 and R2 radius) Warning: You are in a restricted zone. Max flight height restricted to between 20 m and 500 m. Fly Cautiously.(If you are between the range of R1 and R2 radius) Warning: You are approaching a restricted zone, Fly Cautiously. Aircraft Status Indicator Red flashing Free zone No restrictions. None. None. Semi-automatic descent: All stick commands are available except the throttle stick command during the descent and landing process. Motors will stop automatically after landing. When flying in the safety zone, aircraft status indicator will blink red quickly and continue for 3 seconds, then switch to indicate current flying status and continue for 5 seconds at which point it will switch back to red blinking. For safety reasons, please do not fly close to airports, highways, railway stations, railway lines, city centers and other special areas. Maintain line of sight of the aircraft. 44 2015 DJI. All Rights Reserved. FlightPhantom 3 Professional User Manual Preflight Checklist 1. Remote controller, Intelligent Flight Battery, and mobile device are fully charged. 2. Propellers are mounted correctly and firmly. 3. Micro-SD card has been inserted if necessary. 4. Gimbal is functioning as normal. 5. Motors can start and are functioning as normal. 6. DJI Pilot app connected to the aircraft. Calibrating the Compass IMPORTANT: Make sure to calibrate the compass in every new flight location. The compass is very sensitive to electromagnetic interference, which can cause abnormal compass data leading to poor flight performance or even failure. Regular calibration is required for optimum performance. DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and steel reinforcements underground. DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones. DO NOT calibrate beside massive metal objects. DO NOT calibrate indoors. Calibration Procedures Choose an open area to carry out the following procedures. 1. Ensure the compass is calibrated. If you did not calibrate the compass in the Checklist, or if you have changed your position since last calibrating it, tap MODE in the app and select Compass Calibration to calibrate the compass. Then follow the on-screen instructions. 2. Hold and rotate the aircraft horizontally 360 degrees, and the Aircraft Status Indicator will display a solid green light. 2015 DJI. All Rights Reserved. 45 FlightPhantom 3 Professional User Manual 3. Hold the aircraft vertically with nose pointing downward, and rotate it 360 degrees around the center axis. Recalibrate the compass if the Aircraft Status Indicator show solid red. If the Aircraft Status Indicator blinks red and yellow after the calibration, move your aircraft to a different location to calibrate the compass. Calibrate the compass before each flight. Launch DJI Pilot App, follow the on-screen instruction to calibrate the compass. When to Recalibrate 1. When compass data is abnormal, and the Aircraft Status Indicator is blinking red and yellow. 2. When flying in a new location, or a location that is different from your last flight. 3. When the mechanical structure of the Phantom 3 Professional has changed. 4. When severe drifting occurs in flight, i.e. Phantom 3 Professional does not fly in straight line. Auto Take-off and Auto Landing Auto Take-off Use auto take-off to take off your aircraft automatically if the Aircraft Status Indicator displays blinking green. Follow the steps below to use auto take-off:

1. Launch DJI Pilot app, enter Camera page. 2. Ensure the aircraft is in P mode. 3. Go through the pre-flight checklist. 4. Tap 5. Aircraft takes off and hovers at 1.2 meters above ground.

, and confirm flight conditions. Slide to confirm and take-off. Auto-Landing 46 2015 DJI. All Rights Reserved. FlightPhantom 3 Professional User Manual Use auto-landing to land your aircraft automatically if the Aircraft Status Indicator displays blinking green. Follow the steps below to use auto-landing:

1. Ensure the aircraft is in P mode. 2. Check the landing area condition before tapping

, to perform landing. Starting/Stopping the Motors Starting Motors A Combination Stick Command (CSC) is used to start the motors instead of simply pushing the stick up. Push both sticks to their bottom corners to start the motors. Once the motors have spun up, release both sticks simultaneously. Stopping Motors There are two methods to stop the motors. Method 1: When Phantom 3 Professional has landed, push the throttle down , then conduct CSC . Mo-

tors will stop immediately. Release both sticks once motors stop. Method 2: When the aircraft has landed, push the throttle down and hold. The motors will stop after 3 seconds. Method 1 Method 2 Flight Test Take off/Landing Procedures 1. Place the aircraft on open, flat ground with battery indicators facing towards you. 2. Power on the remote controller and your mobile device, then the Intelligent Flight Battery. 3. Launch the DJI Pilot App and enter the Camera page. 4. Wait until the Aircraft Indicator blinks green. This means the Home Point is recorded and it is safe to fly now. If it flashes yellow, it means Home Point is not recorded, and you should not take off. 5. Push the throttle up slowly to take off or using Auto Take-off to take off. 6. Shoot photos and videos using the DJI Pilot app. 7. To land, hover over a level surface and gently pull down on the throttle slowly to descend. 8. After landing, execute the CSC command or hold the throttle at its lowest position for 3 seconds or more until the motors stop. 9. Turn off the Intelligent Flight Battery first, followed by the Remote Controller. 2015 DJI. All Rights Reserved. 47 FlightPhantom 3 Professional User Manual When the Aircraft Status Indicator blinks yellow rapidly during flight, the aircraft has entered Failsafe mode. A low battery level warning is indicated by the Aircraft Status Indicator blinking red slowly or rapidly during flight. Watch video tutorials about flight for more flight information. Video Suggestions and Tips 1. Go through the checklist before each flight. 2. Select desired gimbal operation mode in the DJI Pilot app. 3. Shoot the video when flying in P mode only. 4. Always fly in good weather, such as sunny or windless days. 5. Change camera settings that suit you. These include photo format and exposure compensation. 6. Perform flight tests to establish flight routes and scenes. 7. Push the sticks gently to make aircraft movements stable and smooth. 48 2015 DJI. All Rights Reserved. FlightPhantom 3 Professional User Manual FAQ 2015 DJI. All Rights Reserved. 49 Troubleshooting (FAQ) 50 2015 DJI. All Rights Reserved. FAQ Appendix 2015 DJI. All Rights Reserved. 51 Appendix Specifications Aircraft Weight (Battery &

Propellers Included) Max Ascent Speed Max Descent Speed Max Speed Max Flight Altitude Max Flight Time Operating Temperature GPS Mode Gimbal Controllable Range Vision Positioning Velocity Range Altitude Range Operating Environment Camera Sensor Lens ISO Range Electronic Shutter Speed Image Max Size Still Photography Modes Supported SD Card Types Video Recording Modes 1284 g 6 m/s 2 m/s 16 m/s (ATTI mode, no wind) 6000 m Approximately 24 minutes 0C to 40C GPS/GLOSNASS Pitch - 90 to + 30 Below 8 m/s (2 m above ground) 5 cm-300 cm Brightly lit (lux > 15) patterned surfaces Sony EXMOR 1/2.3 Effective pixels:12.4 M (total pixels: 12.76 M) FOV 94 20mm(35mm format equivalent ) f/2.8, focus at 100-3200(video) 100-1600(photo) 8s -1/8000s 4000 x 3000 Single shoot Burst shooting: 3/5/7 frames Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias Time-lapse Micro SD Max capacity: 64 GB. Class 10 or UHS-1 rating required UHD : 4096x2160p24/25, 3840x2160p24/25/30 FHD:1920x1080p24/25/30/48/50/60 HD:1280x720p24/25/30/48/50/60 Max Bitrate Of Video Storage 60 Mbps Supported File Formats FAT32/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.264) Operating Temperature Range 0C to 40C 52 2015 DJI. All Rights Reserved. Appendix Phantom 3 Professional User Manual Remote Controller Operating Frequency Transmitting Distance Video Output Port Operating Temperature Range Battery Mobile Device Holder 2.400 GHz-2.483 GHz 2000 m (Outdoor And Unobstructed) USB 0C- 40C 6000 mAh LiPo 2S tablet and phone 1.2 A @7.4 V 17.4 V 100 W Working Voltage Charger Voltage Rated Power Intelligent Flight Battery ( PH3-4480 mAh-15.2 V ) Capacity Voltage Battery Type Energy Net Weight Operating Temperature Max Charging Power 4480 mAh 15.2 V LiPo 4S 68 Wh 370 g

-10- 40 100 W A p p e n d x i Aircraft Status Indicator Description Normal Alternatively Red, Green and Yellow Flash Power on and self-check Green and Yellow Flash Alternatively Aircraft warming up X2 Green Flashes Slowly Green Flashes Twice Yellow Flashes Slowly Warning Fast Yellow Flashing Slow Red Flashing Fast Red Flashing Red Flashing Alternatively Solid Red Safe to Fly (P mode with GPS and Vision Positioning) Safe to Fly (P mode with Vision Positioning but without GPS) Safe to Fly (A mode but No GPS and Vision Positioning) Remote Controller Signal Lost Low Battery Warning Critical Low Battery Warning IMU Error Critical Error Red and Yellow Flash Alternatively Compass Calibration Required 2015 DJI. All Rights Reserved. 53 Phantom 3 Professional User Manual Intelligent Orientation Control (IOC) IOC allows users to lock the orientation of aircraft in different fashions. There are three working modes for IOC and you may select the desired IOC modes from the DJI Pilot app. IOC only works under F mode, and user must toggle the flight mode switch to Position 1 to activate IOC. Refer to the table below:

Course Lock (CL) Home Lock (HL)*

Point of Interest (POI)*

Its forward direction is pointing to the nose direction when recording, which is fixed until you re-record it or exit from CL. Record a Home Point (HP), and push Pitch stick to control the aircraft far from or near to the HP. Point of Interest. Record a point of interest (POI), the aircraft can circle around the POI, and the nose always points to the POI.

*Home Lock and Point of Interest feature are coming soon. Prerequisites of IOC Use the IOC feature under the following condition:

Modes IOC Course Lock Home Lock GPS enabled None GPS counts No Yes Yes A p p e n d x i POI Flight Distance Limits None 10m Home Point Aircraft Aircraft 5m~500m Point of Interest Using IOC Toggle the Flight Mode Switch F mode and follow the instructions prompted on the DJI Pilot app to se-

lect the desired IOC features. 54 2015 DJI. All Rights Reserved. Phantom 3 Professional User Manual FCC Compliance FCC Warning Message Any Changes or modifications not expressly roved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The W323 should be installed and operated with minimum distance 20cm between the radiator&

your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. A p p e n d x i IC RSS warning The device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1)The device may not cause interference, and (2)The device must accept any interference,including interference that may cause undesired operation of the device. Le prsent areil est conforme aux CNR d'Industrie Canada licables aux areils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'areil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'areil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. IC Radiation Exposure Statement:

This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This W323 should be installed and operated with minimum distance 20cm between the radiator&

your body. Any Changes or modifications not expressly roved by the party responsible for compliance could void the users authority to operate the equipment. 2015 DJI. All Rights Reserved. 55 Phantom 3 Professional User Manual KCC Warning Message

. NCC Warning Message A p p e n d x i 56 2015 DJI. All Rights Reserved. The content is subject to change. Download the latest version from http://www.dji.com/product/phantom3 If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. 2015 DJI. All Rights Reserved.

PHANTOM 3 Professional User Manual V1.0 2015.03 Using this manual Legends Warning Important Hints and Tips Reference Read Before the First Flight Read the follow documents before using the Phantom 3 Professional for the first time. 1. Disclaimer 2. Phantom 3 Professional Quick Start Guide 3. Phantom 3 Professional User Manual 4. In the Box 5. Safety Guidelines 6. Intelligent Flight Battery Safety Guidelines It is recommended to watch all the tutorial videos on DJI official website and read the Disclaimer before your first flight. Prepare for your first flight by using the Phantom 3 Professional Quick Start Guide. Refer to the user manual for more detailed information. Video Tutorials Please watch the tutorial video below to learn how to use Phantom 3 Professional safely:

http://www.dji.com/product/phantom-3-professional/video Download the DJI Pilot app Download and install the DJI Pilot app before use. Scan the QR code below to download. For Android version of the DJI Pilot app is compatible with Android 4.1.2 or later. For iOS version of the DJI Pilot app is compatible with iOS 8.0 or later. 2 2015 DJI. All Rights Reserved. Contents Using this manual Legends Before Flight Watch the video tutorials Download the DJI Pilot app Product Profile Introduction Feature Highlights Assemble the Aircraft Aircraft Diagram Remote Controller Diagram Aircraft Flight Controller Flight Mode Flight Status Indicator Return to Home (RTH) Smart RTH Low Battery RTH Failsafe RTH Dynamic Home Point Vision Positioning System Flight Recorder Attaching and Detaching the Propellers DJI Intelligent Flight Battery Remote Control Remote Controller Profile Remote Controller Operations Remote Controller Status LED Linking the Remote Controller Remote Controller Compliance Version 2 2 2 2 6 6 7 8 9 12 12 12 13 13 14 15 15 16 17 17 18 24 24 29 29 30 2015 DJI. All Rights Reserved. 3 Camera and Gimbal Camera Profile Gimbal DJI Pilot App Camera Map Academy User Center Flight Flight Environment Requirements Flight Limits and Flight Restriction Area Preflight Checklist Calibrating the Compass Auto Take-off and Auto Landing Flight Test Starting/Stopping the Motors Troubleshooting (FAQ) Appendix Specifications Intelligent Orientation Control (IOC) FCC Compliance 32 33 36 40 40 40 42 42 46 46 47 48 48 53 56 57 4 2015 DJI. All Rights Reserved. Product Profile This chapter introduces the Phantom 3 Professional and lists the components on the aircraft and remote controllers. 2015 DJI. All Rights Reserved. 5 Product Profile Introduction The Phantom 3 Professional is a brand new quadcopter capable of capturing HD video and transmitting an HD video signal out of the box. The built-in camera has an integrated gimbal to maximize stability and weight efficiency while minimizing space. Even when no GPS signal is available, Vision Positioning sys-

tem provides hovering precision. Feature Highlights Camera and Gimbal: The Phantom 3 Professional camera shoots, of course, 4K video and it is capable of capturing 12 megapixel stills. HD Video Downlink: Low latency, HD downlink powered by an enhanced version of the DJI Lightbridge system. DJI Intelligent Flight Battery: 4480 mAh DJI Intelligent Flight Battery employs new battery cells and a bat-

tery management system. Flight Controller: The next generation flight controller system provides a more reliable flight experience. A new flight recorder stores the flight data from each flight, and Vision Positioning enhances hovering preci-

sion when flying indoors and no GPS is available. 6 2015 DJI. All Rights Reserved. Product Profile Assemble the Aircraft Removing Gimbal Clamp Remove the gimbal clamp in the direction as shown below:

Attaching Propellers Attach the propellers with the black nut onto motors with the black axis and spin counter-clockwise to se-

cure. Attach propellers with grey nut onto motors without a grey axis and spin clockwise to secure. Place all propellers onto the correct motor and tighten by hand to secure its position. Preparing Remote Controller Tilt the Mobile Device Holder to the desired position then adjust the antennas. 1. Press the button on the side of the Mobile Device Holder to release the clamp, adjust the clamp to fit 2. Connect the mobile device to the remote controller with a USB cable. 3. Plug one end of the cable into the mobile device, and the other end into the USB port on the back of the size of the mobile device. the remote controller. 1 2 3 2015 DJI. All Rights Reserved. 7 Product ProfilePhantom 3 Professional User Manual Aircraft Diagram

[7]

[6]

[11]

Remote Controller Diagram

[8]

[7]

[6]

8 2015 DJI. All Rights Reserved.

[1]

[2]

[3]

[4]

[5]

[8]

[9]

[10]

[12]

[13]

[1]

[2]

[3]

[4]

[5]

[1] GPS

[2] Propeller

[3] Motor

[4] Front LED

[5] Landing gear

[6] Gimbal and Camera

[7] Aircraft Micro-USB Port

[8] Aircraft Status Indicator

[9] Intelligent Flight Battery

[10] Vision Positioning Sensors

[11] Antennas

[12] Camera Micro-SD Card Slot

[13] Camera Micro-USB Port

[1] Antennas Relays aircraft control and video signal.

[2] Mobile Device Holder Mounting place for your mobile device.

[3] Control Stick Controls aircraft orientation.

[4] Return Home (RTH) Button Press and hold the button to initiate Return to Home (RTH). Product ProfilePhantom 3 Professional User Manual[5] Battery Level LEDs Displays the battery level of the remote controller.

[6] Status LED Displays the remote controller's system status.

[7] Power Button Used to power on or power off the remote controller.

[8] RTH LED Circular LED around the RTH button displays RTH status.

[9] Camera Settings Dial Turn the dial to adjust camera settings. Only functions when the remote controller is connected to a mobile device running the DJI Pilot app.

[10] Playback Button Playback the captured images or videos.

[11] Shutter Button Press to take a photo. If in burst mode, the set number of photos will be taken with one press.

[12] Flight Mode Switch Switch between P, A and F mode.

[13] Video Recording Button Press to start recording video. Press again to stop recording.

[14] Gimbal Dial Use this dial to control the tilt of the gimbal.

[17] Back Right Button Customizable button in DJI Pilot app.

[18] Back Left Button Customizable button in DJI Pilot app.

[19] Power Port

[15]

[16]

[14]

[13]

[12]

[9]

[10]

[11]

[15] Mircro-USB Port Connect to a SD card reader to upgrade the firmware.

[16] USB Port Connect to mobile device or to a USB thumb drive for firmware upgrdae.

[18]

[17]

Connect to a power source to charge the bat-

tery of the remote controller.

[19]

2015 DJI. All Rights Reserved. 9 Product ProfilePhantom 3 Professional User Manual Aircraft This chapter introduces the features of the flight controller, Vision Positioning System and the Intelligent Flight Battery. 10 2015 DJI. All Rights Reserved. Aircraft Flight Controller The Phantom 3 Professional flight controller is based on DJI flight controller with several enhancements such as new flight mode. Three safe modes are available: Failsafe, Return Home and Dynamic Home Point. These features ensure the safe return of your aircraft if the control signal is lost. The flight controller can stores crucial flight data to the on-board storage device for each flight. Flight Mode Three flight modes are available. The details of each flight mode are found in the section below:

P mode (Positioning) : P mode works best when GPS signal is strong. There are three different states of P mode, which will be automatically selected by the Phantom 3 Professional depending on signal strength of GPS and Vision Positioning sensors :

P-GPS: GPS and Vision Positioning both are available, and the aircraft is using GPS for positioning. P-OPTI: Vision Positioning is available but the GPS signal is not. Aircraft is using only Vision Position-

ing for hovering P-ATTI: Neither GPS or Vision Positioning available, aircraft is using only its barometer for positioning, so only altitude is controlled. A mode (Attitude): GPS and Vision Positioning System is not used for stabilization. The aircraft only uses its barometer to stabilize. The aircraft can automatically return home if remote control signal is lost if the Home Point is recorded successfully. F mode (Function): Intelligent Orientation Control (IOC) is activated in this mode. For more information about IOC, refer to the IOC section in the Appendix. Use the Flight Controller mode switch to change the flight mode of the aircraft, refer to the Flight Mode Switch on P24 for more information. Flight Status Indicator The Phantom 3 Professional comes with the Front LED and Aircraft Status Indicator. The positions of these LEDs are shown in the figure below:

Front LED Aircraft Status Indicator The Front shows the orientation of the aircraft. The Front LED displays solid red. Aircraft Status Indicator shows the system status of the flight controller. Refer to the table below for more information about the Aircraft Status Indicator:

2015 DJI. All Rights Reserved. 11 Aircraft Aircraft Status Indicator Description Normal Alternatively Red, Green and Yellow Flash Power on and self-check Green and Yellow Flash Alternatively Green Flashes Slowly X2 Green Flashes Twice Yellow Flashes Slowly Warning Fast Yellow Flashing Slow Red Flashing Fast Red Flashing Red Flashing Alternatively Solid Red Red and Yellow Flash Alternatively Aircraft warming up Safe to Fly (P mode with GPS and Vision Positioning) Safe to Fly (P mode with Vision Positioning but without GPS) Safe to Fly (A mode but No GPS and Vision Positioning) Remote Controller Signal Lost Low Battery Warning Critical Low Battery Warning IMU Error Critical Error Compass Calibration Required Return to Home (RTH) The Return to Home (RTH) brings the aircraft back to the last recorded Home Point. There are three cases that will trigger RTH procedure; they are Smart RTH, Low Battery RTH and Failsafe RTH. The remaining part of this section will describe these three cases in details. Home Point GPS Description The Home Point is the location at which your aircraft takes off when the GPS signal is strong. You can view the GPS signal strength through the GPS icon (

). Aircraft status indicator will blink rapidly when home point is recorded. Smart RTH Use the RTH button on the remote controller (refer to RTH button on P28 for more information) or tap the RTH button in the DJI Pilot app when GPS is available to start Smart RTH. The aircraft returns to the latest recorded Home Point, you may control the aircraft's orientation to avoid collision during the Smart RTH. Press and hold the Smart RTH button once to start the process, press the Smart RTH button again to exit Smart RTH and regain the control. 12 2015 DJI. All Rights Reserved. AircraftPhantom 3 Professional User Manual Low Battery RTH The low battery level failsafe is triggered when the DJI Intelligent Flight Battery is depleted to a point that may affect the safe return of the aircraft. Users are advised to return home or land the aircraft immediately when these warnings are prompted. DJI Pilot app will advise user to return the aircraft to the Home Point when low battery warning is triggered. Aircraft will automatically return to the Home Point if no action is taken after 10 seconds countdown. User can cancel the RTH by pressing once on the RTH button. The thresholds for these warnings are automatically determined based on the current aircraft altitude and its distance from the Home Point. Aircraft will land automatically if the current battery level can only support the aircraft to land from the current altitude. User can use the remote controller to control the aircrafts orientation during the landing process. The Battery Level Indicator is displayed in the DJI Pilot app, and is described below Critical Low battery level warning(Red) Sufficient battery level(Green) Low battery level warning(Yellow) Remaining flight time Power requires to return home Battery level Indicator Battery Level Warning Remark Aircraft Status Indicator DJI Pilot app Flight Instructions Low battery level warning The battery power is low. Please land the aircraft. Aircraft status indicator blinks RED slowly. Tap Go-home to have the aircraft return to the Home point and land automatically, or Cancel to resume normal flight. If no action is taken, the aircraft will automatically go home and land after 10 seconds. Remote controller will sound an alarm. Fly the aircraft back and land it as soon as possible, then stop the motors and replace the battery. Critical Low battery level warning The aircraft must land immediately. Aircraft status indicator blinks RED quickly. The DJI Pilot app screen will flash red and aircraft starts to descend. Remote controller will sound an alarm. The aircraft will begin to descend and land automatically. Estimated remaining flight time Estimated remaining flight based on current battery level. N/A N/A N/A 2015 DJI. All Rights Reserved. 13 AircraftPhantom 3 Professional User Manual When the critical battery level warning activates and the aircraft is descending to land automatically, you may push the throttle upward to hover the aircraft and navigate it to a more appropriate location for landing. Color zones and markers on the battery level indicator reflect estimated remaining flight time and are adjusted automatically, according to the aircrafts current status. Failsafe RTH Failsafe RTH is activated automatically if remote controller signal (including video relay signal) is lost for more than 3 seconds provided that Home Point has been successfully recorded and compass is working normally. Return home process may be interrupted and the operator can regain control over the aircraft if a remote controller signal is resumed. Failsafe Illustration 1 Record Home Point (HP) 3 Remote Controller Signal Lost 2 Confirm Home Point Blinking Green 4 Signal Lost Lasts 3secs. Blinking Green 5 Go Home(altitude adjustable) Fast Blinking Yellow 6 Landing after Hovering 5 secs

>3S Height over HP>20m 20m Elevate to 20m Fast Blinking Yellow Fast Blinking Yellow Height over HP<=20m<=20m Fast Blinking Yellow Aircraft cannot avoid obstruction during the Failsafe RTH, therefore it is important to set an suitable Failsafe altitude before each flight. Launch the DJI Pilot app and enter Camera view and select MODE to set the Failsafe altitude. Aircraft will stop ascending and return to the Home Point immediately if throttle stick is moved during the Failsafe RTH procedure Dynamic Home Point Dynamic home point is useful in situations when you are in motion and require a Home Point that is different from the takeoff point. You may only use the Dynamic Home Point feature on the GPS - enabled mobile device. Ensure the space above the GPS module is not obstructed when using Dynamic Home Point. 14 2015 DJI. All Rights Reserved. AircraftPhantom 3 Professional User Manual