DJI Motion Controller
(Model: FC7BMC)
Quick Start Guide
v1.0
Introduction
1. Battery Level Indicator
2. Take‐off/Landing Button (non‐M mode)
Lock/Unlock Button (M mode)
Flight Mode Switch
Flight Pause Button
Shutter/Record Button
3.
4.
5. Gimbal Slider
6.
7. Throttle Trigger
8.
9. USB‐C‐Port
10. Power Button
Lanyard Attachment
Charging
Checking Battery Levels and Powering On/Off
Press once to check the battery level.
Press, then press and hold to turn on/off.
Activation
Linking
When the remote controller is powered on, connect the USB‐C port to your computer and run DJI
ASSISTANT 2 for activation.
1) Press the link button on the goggles. The goggles will beep continually.
2) Press and hold the power button of the aircraft until the battery level indicator blinks in
sequence.
3) T
The battery le
top beeping w
st
evel indicator
when they ar
of the aircra
re successfull
ft turns solid
ly linked and
and displays
the video dis
the battery l
splay is norma
level. The gog
al.
ggles
d the power b
button of the
e aircraft unti
l the battery
level indicato
or blinks in
d the power b
ndicator blin
ontroller stop
n solid and di
button of the
ks in sequenc
ps beeping w
isplay the bat
e remote cont
ce.
hen successf
ttery level.
troller until it
t beeps conti
nually and th
he
ully linked an
nd both the b
attery level
1) P
Press and hold
equence.
s
2) P
Press and hold
b
battery level i
3) T
The remote co
ndicators turn
in
Usag
ge
1. Pr
ress, then pre
ess and hold t
the power bu
utton to turn
on the remo
te controller.
2. Do
ouble click th
he Lock/Unloc
ck Button to
unlock the re
emote contro
oller.
3. Pr
ress the throt
he remote con
th
o start the mo
ttle trigger to
ontrol the airc
ntroller to co
otors and con
ntrol the aircr
.
craft to flight.
raft to ascend
d or descend
. Move
4. Press and hold the Shutter/Record Button to switch the shooting mode. Tap to take a photo or to
start or stop recording a video.
Spec
cification
ns
Mode
Opera
l
ht
Weigh
y
ating Frequec
Distance
Transmission
of
free
f
structed,
erence)
mitter Power
Max T
(unob
interfe
Transm
(EIRP)
Opera
ating Tempera
ature
C7BMC
FC
65g
1
.400‐2.4835
0 km (FCC); 6
1
2
.4 GHz: ≤2
2
.8 GHz: ≤31
5
10° to 40° C
‐1
GHz；5.725‐
6 km (CE/SRR
‐5.850 GHz
RC/MIC)
9 dBm (FCC
1.5 dBm (FCC
), ≤20 dBmm (CE/SRRC/M
m(SRRC), ≤14
C), ≤19 dBm
MIC)
4 dBm (CE)
Compliance Information
FCC ComplianceNotice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co‐located or operating in conjunction with any other
antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by
the Federal Communications Commission (USA). These requirements set a SAR limit of 4.0 W/kg
averaged over ten gram of tissue. The highest SAR value reported under this standard
during product certification for handheld use mode.
ISED Compliance Notice
This device contains licence‐exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence‐exempt RSS(s). Operation is subject to the following
two conditions: (1)This device may not cause interference.(2)This device must accept any
interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :(1)L’appareil ne doit
pas produire de brouillage; (2)L’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co‐located or operating in conjunction with any other
antenna or transmitter.The portable device is designed to meet the requirements for exposure to
radio waves established by the ISED.
These requirements set a SAR limit of 4.0 W/kg averaged over ten gram of tissue. The highest SAR
value reported under this standard during product certification for handheld use mode.
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un
environnement non contrôlé. L’utilisateur final doit suivre les instructions spécifiques pour satisfaire
les normes. Cet émetteur ne doit pas être co‐implanté ou fonctionner en conjonction avec toute
autre antenne ou transmetteur. Le dispositif portatif est conçu pour répondre aux
exigences d’exposition aux ondes radio établie par le développement énergétique DURABLE.
Ces exigences fixent une limite DAS de 4,0 W / kg en moyenne sur dix grammes de tissu. Valeur DAS la
plus élevée rapportée selon cette norme lors de la certification du produit pour le mode d'utilisation
portable.