FCC ID: SS3-QFP2AS22 DJI O3 Air Unit

DJI O3 Air Unit User Guide v1.0 2022.1 Disclaimer By using this product, you signify that you have read, understand, and accept the terms and conditions here. EXCEPT AS EXPRESSLY PROVIDED IN AFTER-SALES SERVICE POLICIES AVAILABLE AT (HTTP://WWW.DJI.COM/SERVICE). Introduction DJI Air Unit is an advanced video transmission module that can be mounted on a racing drone. It can be used with DJI Goggles and a remote controller to transmit video, control signals, and flight controller information wirelesslyv. 1. Camera 2. Coaxial Cable 3. Linking Status Indicator 4. Link Button 5. 3-in-1 Cable Connector 6. Antenna Ports 7. USB-C Port 8. microSD Card Slot Installation Mount the air unit to a racing drone and refer to the illustration below to connect the 3-in-1 cable. 3-in-1 Cable (Power, DJI HDL, UART) RED: Power (7.4-26.4 V) BLACK: Power GND WHITE: UART RX (Connects to Flight Controller OSD TX, 0-3.3 V) GRAY: UART TX (Connects to Flight Controller OSD RX, 0-3.3 V) BROWN: Signal GND YELLOW: DJI HDL (Connects to Flight Controller S.Bus, 0-3.3 V) An electric soldering iron and soldering tin are required for connection. Make sure that there are no short circuits or open circuits when soldering the cables. The air unit may become hot during or after operation. DO NOT touch the air unit before it cools down. DO NOT use the air unit for an extended period when the temperature is high or there is poor ventilation. Otherwise, the air unit may overheat and enter low-power mode which will affect the performance. When installing the antenna, make sure that the antenna is not blocked by any component. Activation When powered on, connect the USB-C port of the device to your computer and run DJI AssistantTM 2 to activate the device. Firmware Update Use DJI Assistant 2 to update the firmware of the air unit, goggles, and remote controller separately. Restart the device after the firmware update is complete. Linking Power on the air unit, the goggles, and the remote controller. 1. Press the link button of the air unit and the goggles respectively. The linking status indicator of the air unit blinks red, and the goggles starts to beep continually. 2. When linking is successful, the linking status indicator of the air unit turns solid green, the goggles stop beeping, and the live view will be displayed. 3. Press the link button of the air unit, the linking status indicator of the air unit blinks red. Press and hold the power button of the remote controller, the remote controller starts to beep continually and the status indicator blinks in sequence. 4. When linking is successful, the linking status indicators of the air unit turns solid green and the remote controller stops beeping. Specifications Weight Dimensions Operating Temperature Supported Flight Controller System Power Input Operating Frequency Transmitter Power (EIRP) 33.7 g (includes the camera module) The dimensions of the video transmission module and camera module are shown in the illustration after the spec table. Coaxial Cable: 115 mm 0 to 40 C (32 to 104 F) BetaFlight 7.4 V 26.4 V 2.400~2.4835 GHzRX Only; 5.725~5.850 GHz FCC: <33 dBm;

SRRC: <30 dBm;

CE: <14 dBm Compliance Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment ISED Compliance Notice This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device. L'metteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR d'Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions

:(1)L'appareil ne doit pas produire de brouillage;

suivantes

(2)L'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with RSS102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites d'exposition aux radiations CNR102 tablies pour un environnement non contr?l. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017. A copy of the GB Declaration of Conformity is available online at www.dji.com/euro-compliance In order to avoid the possibility of exceeding the radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Environmentally friendly disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances. Thailand Warning message

. Mexico Warning message La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Brazil Warning message Informaes sobre Regulamentao Estes equipamentos esto certificados e homologados pela ANATEL. Para maiores www.anatel.gov.br. informaes, consulte o site da ANATEL:

Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Este produto est homologado pela Anatel de acordo com os procedimentos regulamentados para avaliao da conformidade de produtos para telecomunicaes e atende aos requisitos tcnicos aplicados, incluindo os limites de exposio da Taxa de Absoro Especfica referente a campos eltricos, magnticos e eletromagnticos de radiofrequncia.

} ne: 03 AIR UNIT 4 Fs ICES-003 (B)/NMB-003(B)

| ecco: $85- ID: SS3-QFP2AS22 IC: TI8OSA-QFP2AS22 ae emia igh temperature ANATEL:XXXXXXXXXX AY IIPBASEOIS ESA IRAS) sed SZ DJI Technology Co., Ltd. Made in China

Authority to Act as Agent Date: 2021-02-26 TUV Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern:

certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. specified by TUV Rheinland Group, still resides with SZ DIT TECHNOLOGY CO., LTD / 14th floor, West Wing, Skyworth Semiconductor Design Building NO.18 Gaoxin South 4th Ave, Nanshan District, Shenzhen, Guangdong. Chi 5 : g g. nha For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. F urther, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: Permanent By : fos Wood fajia wang

. EE

(Signature) (Print Name) Title : Compliance Supervisor Telephone _ : +8675586152250

$e On behalf of : SZ DJI TECHNOLOGY CO., LTD eee

(Company Name) QF094234 Page 1 of 1 Revision 0

Standard Form Request for Confidentiality Letter SZ DJI TECHNOLOGY CO.,LTD. Date: 2022-06-07 Subject: Confidentiality Request for FCC ID: SS3-QFP2AS22 and IC: 11805A-QFP2AS22 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent Permanent Permanent Permanent Permanent n/a n/a Exhibit Block Diagrams Internal Photos ***

Operation Description/Theory of Operation Tune-Up Procedure Schematics Users Manual***

Test Setup External Photos SZ DJI TECHNOLOGY CO.,LTD. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. (*** PAG only) Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By:

________Fajia Wang________________ _________________________________

(Signature/Title)

(Print name) MS-0044715 Page 1 of 1 Revision 0