FCC ID: SS3-RM51021 DJI RC Pro

DJI RC Pro Quick Start Guide Disclaimer Carefully read this entire document and all safe and lawful practices provided by DJITM before using this product for the first time. Failure to read and follow instructions and warnings may result in serious injury to yourself or others, damage to your DJI product, or damage to other objects in the vicinity. By using this product, you hereby signify that you have read this document carefully and that you understand and agree to abide by all terms and conditions of this document and all relevant documents of this product. You agree that you are solely responsible for your own conduct while using this product and for any consequences thereof. DJI accepts no liability for damage, injury, or any legal responsibility incurred directly or indirectly from the use of this product. DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as DJI) and its affiliated companies. Names of products, brands, etc., appearing in this document are trademarks or registered trademarks of their respective owner companies. This product and document are copyrighted by DJI with all rights reserved. No part of this product or document shall be reproduced in any form without the prior written consent or authorization of DJI. This document and all other collateral documents are subject to change at the sole discretion of DJI. This content is subject to change without prior notice. For up to date product information, visit the product page for this product at This document is available in various languages. In the event of divergence among different versions, the English http://www.dji.com. version shall prevail. Important Stay alert when using the DJI DJI RC PRO to control an Unmanned Aerial Vehicle (UAV). Carelessness may result in serious harm to yourself and others. Download and read the user manuals for the aircraft and DJI RC PRO before using for the first time. 1. Fully charge the remote controller before each flight. 2. The remote controller will sound an alert if it is powered on but has not been used for five minutes. It will automatically power off after a further 30 seconds. Move the control sticks or perform any other remote controller action to cancel the alert. transmission. performance. 3. Make sure the antennas of the remote controller are unfolded and adjusted to the proper position for optimal 4. Contact DJI Support to repair or replace the antennas if they are damaged. Damaged antennas greatly decrease 5. Link the remote controller and the aircraft every time the aircraft is changed. 6. Make sure to power off the aircraft before the remote controller. 7. Fully charge the remote controller every three months. 8. Charge the remote controller immediately if the power level reaches 0%. Otherwise, the remote controller may be damaged due to being over discharged for an extended period. Discharge the remote controller to between 40% and 60% if stored for an extended period. controller may be affected due to overheating. 9. DO NOT cover the air vent or the air intake on the remote controller. Otherwise, the performance of the remote 10. DO NOT disassemble the remote controller without the assistance of a DJI authorized dealer. Contact DJI or a DJI authorized dealer to replace the components of the remote controller. Introduction The DJI DJI RC PRO features O3, the latest version of DJIs signature OCUSYNCTM image transmission technology, and can transmit a live HD view from the camera of an aircraft [1] at a distance of up to 12 km [2]. Users can connect to the internet via Wi-Fi or by using a 4G dongle and the Android operating system comes with a variety of functions such as Bluetooth and GNNS. The built-in 5.5-in high brightness 1000 cd/m2 screen boasts a resolution of 19201080 pixels while the remote controller comes with a wide range of aircraft and gimbal controls as well as customizable buttons and has a maximum operating time of 3 hours [3]. Overview 1 4 2 3 8 7 5 6 10 11 12 13 14 15 19 18 16 17 20 23 25 24 21 22 Confirm Button/Customizable Button C3 Antennas Back Button/Function Button Control Sticks 9 RTH Button 1. 2. 3. 4. 5. 6. 7. 8. 9. Flight Pause Button Flight Mode Switch 5D Button Power Button 10. Touchscreen 11. microSD Card Slot 12. USB-C Port 13. Mini HDMI Port 14. Gimbal Dial 15. Record Button 16. Status LED 17. Battery Level LEDs 18. Focus/Shutter Button 19. Camera Settings Dial 20. Air Vent 21. Control Sticks Storage Slots [4]

22. Customizable C1 Button 23. Speaker 24. Customizable C2 Button 25. Air Intake

[1] Only available with aircraft that support O3. Refer to the Specifications for more information on supported aircraft.

[2] The Smart Controller V.2 can reach its maximum transmission distance (FCC) in a wide open area with no electromagnetic interference using a MAVICTM 3 at an altitude of approximately 120 meters.

[3] The maximum operating time was tested in a lab environment and is for reference only.

[4] A pair of control sticks are stored in the control sticks storage slot before delivery. The control sticks have already been mounted to the remote controller in the illustration in the Overview section. 1. Battery Level and Charging Press the power button to check the battery level. Press once and then press and hold or hold for a few seconds to power the remote controller on or off. It takes approximately two and a half hours to fully charge the remote controller using a standard USB power adapter. It is recommended to use an FCC/CE certified USB power adapter rated 12V or 15V. Recharge the battery at least every three months to prevent over discharging. The battery depletes when stored for an extended period. 2. Preparing the DJI RC PRO Remove the control sticks from the Attach the control sticks Control sticks attached storage slots and twist to secure Unfold the antennas Rotate the antennas Lift the antennas The optimal transmission range is where the antennas are facing toward the aircraft and the angle between the antennas and the back of the remote controller is 180 or 270. The illustrations above show situations where the operator and aircraft are far away. Make sure the control sticks are firmly mounted. A prompt will be received in DJI Fly if the transmission signal is weak during flight. Adjust the antennas to make sure that the aircraft is in the optimal transmission range. 3. Activating the DJI RC PRO The remote controller needs to be activated before using for the first time. An internet connection is required for activation. Power on the remote Select the language Follow the prompts to activate controller Check the internet connection if activation fails. Try to activate the remote controller again if the internet connection is normal. Contact DJI if activation fails several times. 4. Linking The remote controller is already linked to the aircraft when it is purchased together as part of a combo. Otherwise, follow the steps below to link the remote controller and the aircraft after activation. 1. Power on the remote controller and the aircraft. 2. Press the customizable button C1, customizable button C2, and the record button simultaneously. The status LED will blink blue and the remote controller will beep twice to indicate linking has started. 3. Press the linking button of the aircraft. The status LED of the remote controller will turn solid green if linking is successful. Refer to the DJI DJI RC PRO User Manual for more information about linking. To download the user manual, visit http://www.dji.com/dji-smart-controller 5. Flight Auto Takeoff/Landing Before takeoff, make sure that takeoff is permitted in the camera view of DJI Fly. Tap this icon in the camera view. When the prompt appears, press and hold the button to initiate auto takeoff or landing. Manual Takeoff/Landing Perform combination stick command to start/stop the motors. Takeoff Landing Slowly push the left control stick Slowly push the left control stick

(Mode 2) up to take off. down until the aircraft lands. Hold for three seconds to stop the motors. The default control stick mode is Mode 2. The left control stick controls the altitude and heading of the aircraft, while the right control stick controls the forward, backward, and sideward movements. The gimbal dial controls the tilt of the camera. The motors can only be stopped mid-flight when the flight controller detects a critical error. Make sure the remote controller is linked to the aircraft. Specifications O3 (OcuSync 3.0) Operation Frequency Range 2.400-2.4835 GHz; 5.725-5.850 GHz*

Max Transmission Distance 12 km (FCC); 8 km (CE); 8 km (SRRC); 8 km (MIC)

(Unobstructed, free of interference) Transmission Power (EIRP) 2.400-2.4835 GHz:

31 dBm (FCC); 18.5 dBm (CE) 18.5 dBm (SRRC); 18.5 dBm (MIC) 5.725-5.850 GHz:

31.5 dBm (FCC); 12.5 dBm (CE) 18.5 dBm (SRRC) WiFi Direct, Wi-Fi Display, 802.11b/a/g/n/ac/ax 22 MIMO Wi-Fi Protocol Operation Frequency Range 2.400-2.4835 GHz; 5.15G-5.25G; 5.725-5.850 GHz*

Transmission Power (EIRP) 2.400-2.4835 GHz: 23 dBm (FCC); 21 dBmCE/SRRC/MIC/KCC 5.1G GHz23 dBmFCC21 dBmCE/SRRC/MIC/KCC 5.725-5.850 GHz: 24 dBm (FCC); 12.5 dBm (CE) 24 dBm (SRRC); 12.5 dBm (KCC) Bluetooth Protocol Bluetooth 5.1 Operation Frequency Range 2.400-2.4835 GHz Transmission Power (EIRP) 6 dBm (FCC); 6 dBm(CE) 6 dBm (SRRC); 6 dBm (MIC); 6 dBm (KCC) 18650 Li-ion (5000 mAh @ 7.2 V) Recommended to use USB power adapters rated 12V or 15V General Battery Charging Type Rated Power Charging Time Operating Time 12 W 3 hours Storage Capacity ROM 32GB + expandable storage via microSD card 2.5 hours (using a USB power adapter rated 12V) Video Output Port Mini HDMI Port Operation Temperature Range

-20 to 40 C (-4 to 104 F) Storage Temperature Range Less than one month: -30 to 60 C (-22 to 140 F) One to three months: -30 to 45 C (-22 to 113 F) Three to six months: -30 to 35 C (-22 to 95 F) More than six months: -30 to 25 C (-22 to 77 F) Charging Temperature Range 5 to 40 C (41 to 104 F) Supported Aircraft Models**

Mavic 3, DJI Air 2S, Mavic Air 2 GNSS Weight Model GPS+GLONASS Approx. 750 g RM510B

* 5.8 GHz is unavailable in some countries due to local regulations.

** The DJI RC PRO will support more DJI aircraft in future. Visit the official website for the latest information. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Compliance Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of averaged over one gram of tissue. The highest SAR value reported under this standard during product certification 4 W/kg for use when properly in the limbs. ISED Compliance Notice This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :(1)Lappareil ne doit pas produire de brouillage;

(2)Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated. le dispositif utilis dans la bande 5150-5250 MHz est rserv une utilisation en intrieur afin de rduire le risque de brouillage prjudiciable aux systmes mobiles par satellite dans le mme canal;le cas chant, le (s) type (s) d'antenne, le (s) modle (s) d'antenne et l'angle (s) d'inclinaison le plus dfavorable ncessaire (s) pour rester conforme (e) au p.e. L'exigence relative au masque d'lvation nonce la section 6.2.2.3 doit tre clairement indique. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 4 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly in the limbs. Cet quipement est conforme aux limites d'exposition aux rayonnements de l'ised pour les environnements non contrls. L'utilisateur final doit se conformer des instructions d'exploitation spcifiques afin de respecter la conformit l'exposition aux radiofrquences. Cet metteur ne doit pas tre au mme endroit ni fonctionner avec une autre antenne ou un autre metteur. L'quipement portatif doit tre conu de manire satisfaire aux exigences d'exposition aux ondes radio spcifies dans l'ised. Ces exigences fixent une limite moyenne de SAR de 4 W / kg pour un gramme de tissu. Au cours de la certification du produit, la valeur SAR la plus leve rapporte conformment la prsente norme pour une utilisation normale des membres. EU Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (DJI Action 2) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany GB Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device(DJI Action 2) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017. A copy of the GB Declaration of Conformity is available online at www.dji.com/euro-compliance Declaracin de cumplimiento UE: SZ DJI Osmo Technology Co., Ltd. por la presente declara que este dispositivo(DJI Action 2) cumple los requisitos bsicos y el resto de provisiones relevantes de la Directiva 2014/53/EU. Hay disponible online una copia de la Declaracin de conformidad UE en www.dji.com/euro-compliance Direccin de contacto de la UE: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany EU-verklaring van overeenstemming: SZ DJI Osmo Technology Co., Ltd. verklaart hierbij dat dit apparaat(DJI Action 2) voldoet aan de essentile vereisten en andere relevante bepalingen van Richtlijn 2014/53/EU. De EU-verklaring van overeenstemming is online beschikbaar op www.dji.com/euro-compliance Contactadres EU: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany Declarao de conformidade da UE: A SZ DJI Osmo Technology Co., Ltd. declara, atravs deste documento, que este dispositivo(DJI Action 2) est em conformidade com os requisitos essenciais e outras disposies relevantes da Diretiva 2014/53/EU. Existe uma cpia da Declarao de conformidade da UE disponvel online em www.dji.com/euro-compliance Endereo de contacto na UE: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany Dichiarazione di conformit UE: SZ DJI Osmo Technology Co., Ltd. dichiara che il presente dispositivo(DJI Action 2) conforme ai requisiti essenziali e alle altre disposizioni rilevanti della direttiva 2014/53/EU. Una copia della dichiarazione di conformit UE disponibile online all'indirizzo Web www.dji.com/euro-

Indirizzo di contatto UE: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany Dclaration de conformit UE : Par la prsente, SZ DJI Osmo Technology Co., Ltd. dclare que cet appareil(DJI Action 2) est conforme aux principales exigences et autres clauses pertinentes de la directive europenne Une copie de la dclaration de conformit UE est disponible sur le site www.dji.com/euro-compliance Adresse de contact pour l'UE : DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany PRCAUTIONS D'USAGE DE L'APPAREIL qui peuvent produire des interfrences Nutilisez pas lappareil dans un hpital, un avion ou un quipement automobile en raison des radiofrquences Maintenez une distance minimale de 15 cm entre votre appareil et un stimulateur cardiaque pour viter toute interfrence Eloigner les quipements radiolectriques du ventre des femmes enceintes. Eloigner les quipements radiolectriques du bas-ventre des adolescents. Le dbit d'absorption spcifique (DAS) local quantifie l'exposition de l'utilisateur aux ondes lectromagntiques de l'quipement concern. Le DAS maximal autoris est de 2 W/ kg pour la tte et le tronc compliance 2014/53/EU. et de 4 W/ kg pour les membres. La ou les valeurs du dbit d'absorption spcifique des RM510B DAS tronc: X.XXW/ kg DAS membres: X.XXW/ kg This device is restricted to indoor use when operating in the 5150-5250MHz frequency range in all EU/EFTA member states and Turkey. Im Frequenzbereich 5150 5250 MHz darf dieses Gert in allen EU/EFTA-Mitgliedsstaaten und der Trkei nur innerhalb von Gebuden verwendet werden. Este dispositivo est limitado a su uso en interiores cuando est funcionando en el rango de frecuenciade 5150-5250 MHz en todos los estados miembros de la UE/AELC y Turqua. Cet appareil est rserv un usage en intrieur dans une plage de frquence de 5 150 5 250 MHz dans tous les pays membres de l'Union Europenne et de l'Association europenne de libre-change,ainsi qu'en Turquie. Il presente dispositivo limitato all'uso in ambienti interni se utilizzato nell'intervallo di frequenze difunzionamento 5150-5250 MHz in tutti gli stati dell'UE/AELS e in Turchia. Dit apparaat mag in landen van de EU/EFTA en Turkije alleen in binnenruimtes worden gebruikt wanneer het frequentiebereik 5150-5250 MHz is ingesteld. Este dispositivo est restrito para uso em reas internas ao operar na faixa de frequncia de 5150-5250MHz em todos os estados-membros da UE/EFTA e Turquia. 5150-5250

, /, . 5150-5250MHz,/Indoor use Only

DJI RC Pro Quick Start Guide Disclaimer Carefully read this entire document and all safe and lawful practices provided by DJI TM before using this product for the first time. Failure to read and follow instructions and warnings may result in serious injury to yourself or others, damage to your DJI product, or damage to other objects in the vicinity. By using this product, you hereby signify that you have read this document carefully and that you understand and agree to abide by all terms and conditions of this document and all relevant documents of this product. You agree that you are solely responsible for your own conduct while using this product and for any consequences thereof. DJI accepts no liability for damage, injury, or any legal responsibility incurred directly or indirectly from the use of this product. DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as DJI) and its affiliated companies. Names of products, brands, etc., appearing in this document are trademarks or registered trademarks of their respective owner companies. This product and document are copyrighted by DJI with all rights reserved. No part of this product or document shall be reproduced in any form without the prior written consent or authorization of DJI. This document and all other collateral documents are subject to change at the sole discretion of DJI. This content is subject to change without prior notice. For up to date product information, visit the product page for this product at This document is available in various languages. In the event of divergence among different versions, the English http://www.dji.com. version shall prevail. Important action to cancel the alert. transmission. performance. Stay alert when using the DJI Smart Controller V2.0 to control an Unmanned Aerial Vehicle (UAV). Carelessness may result in serious harm to yourself and others. Download and read the user manuals for the aircraft and Smart Controller V2.0 before using for the first time. 1. Fully charge the remote controller before each flight. 2. The remote controller will sound an alert if it is powered on but has not been used for five minutes. It will automatically power off after a further 30 seconds. Move the control sticks or perform any other remote controller 3. Make sure the antennas of the remote controller are unfolded and adjusted to the proper position for optimal 4. Contact DJI Support to repair or replace the antennas if they are damaged. Damaged antennas greatly decrease 5. Link the remote controller and the aircraft every time the aircraft is changed. 6. Make sure to power off the aircraft before the remote controller. 7. Fully charge the remote controller every three months. 8. Charge the remote controller immediately if the power level reaches 0%. Otherwise, the remote controller may be damaged due to being over discharged for an extended period. Discharge the remote controller to between 40% and 60% if stored for an extended period. controller may be affected due to overheating. 9. DO NOT cover the air vent or the air intake on the remote controller. Otherwise, the performance of the remote 10. DO NOT disassemble the remote controller without the assistance of a DJI authorized dealer. Contact DJI or a DJI authorized dealer to replace the components of the remote controller. Introduction The DJI Smart Controller V2.0 features O3, the latest version of DJIs signature OCUSYNCTM image transmission technology, and can transmit a live HD view from the camera of an aircraft [1] at a distance of up to 12 km [2]. Users can connect to the internet via Wi-Fi or by using a 4G dongle and the Android operating system comes with a variety of functions such as Bluetooth and GNNS. The built-in 5.5-in high brightness 1000 cd/m2 screen boasts a resolution of 19201080 pixels while the remote controller comes with a wide range of aircraft and gimbal controls as well as customizable buttons and has a maximum operating time of 3 hours [3]. Overview 1 4 2 3 8 7 5 6 10 11 12 13 14 15 16 17 20 23 25 24 21 22 1. Antennas 2. Back Button/Function Button 3. Control Sticks 9 4. RTH Button 5. 6. 7. 8. Flight Pause Button Flight Mode Switch 5D Button Power Button 9. Confirm Button/Customizable Button C3 19 18 10. Touchscreen 11. microSD Card Slot 12. USB-C Port 13. Mini HDMI Port 14. Gimbal Dial 15. Record Button 16. Status LED 17. Battery Level LEDs 18. Focus/Shutter Button 19. Camera Settings Dial 20. Air Vent 21. Control Sticks Storage Slots [4]

22. Customizable C1 Button 23. Speaker 24. Customizable C2 Button 25. Air Intake

[1] Only available with aircraft that support O3. Refer to the Specifications for more information on supported aircraft.

[2] The Smart Controller V.2 can reach its maximum transmission distance (FCC) in a wide open area with no electromagnetic interference using a MAVICTM 3 at an altitude of approximately 120 meters.

[3] The maximum operating time was tested in a lab environment and is for reference only.

[4] A pair of control sticks are stored in the control sticks storage slot before delivery. The control sticks have already been mounted to the remote controller in the illustration in the Overview section. 1. Battery Level and Charging Press the power button to check the battery level. Press once and then press and hold or hold for a few seconds to power the remote controller on or off. It takes approximately two and a half hours to fully charge the remote controller using a standard USB power adapter. It is recommended to use an FCC/CE certified USB power adapter rated 12V or 15V. Recharge the battery at least every three months to prevent over discharging. The battery depletes when stored for an extended period. 2. Preparing the Smart Controller V2.0 Remove the control sticks from the Attach the control sticks Control sticks attached storage slots and twist to secure Unfold the antennas Rotate the antennas Lift the antennas The optimal transmission range is where the antennas are facing toward the aircraft and the angle between the antennas and the back of the remote controller is 180 or 270. The illustrations above show situations where the operator and aircraft are far away. Make sure the control sticks are firmly mounted. A prompt will be received in DJI Fly if the transmission signal is weak during flight. Adjust the antennas to make sure that the aircraft is in the optimal transmission range. 3. Activating the Smart Controller V2.0 The remote controller needs to be activated before using for the first time. An internet connection is required for activation. Power on the remote Select the language Follow the prompts to activate controller Check the internet connection if activation fails. Try to activate the remote controller again if the internet connection is normal. Contact DJI if activation fails several times. 4. Linking The remote controller is already linked to the aircraft when it is purchased together as part of a combo. Otherwise, follow the steps below to link the remote controller and the aircraft after activation. 1. Power on the remote controller and the aircraft. 2. Press the customizable button C1, customizable button C2, and the record button simultaneously. The status LED will blink blue and the remote controller will beep twice to indicate linking has started. 3. Press the linking button of the aircraft. The status LED of the remote controller will turn solid green if linking is successful. Refer to the DJI Smart Controller V2.0 User Manual for more information about linking. To download the user manual, visit http://www.dji.com/dji-smart-controller 5. Flight Before takeoff, make sure that takeoff is permitted in the camera view of DJI Fly. Auto Takeoff/Landing Tap this icon in the camera view. When the prompt appears, press and hold the button to initiate auto takeoff or landing. Manual Takeoff/Landing Perform combination stick command to start/stop the motors. Takeoff Landing Slowly push the left control stick Slowly push the left control stick

(Mode 2) up to take off. down until the aircraft lands. Hold for three seconds to stop the motors. The default control stick mode is Mode 2. The left control stick controls the altitude and heading of the aircraft, while the right control stick controls the forward, backward, and sideward movements. The gimbal dial controls the tilt of the camera. The motors can only be stopped mid-flight when the flight controller detects a critical error. Make sure the remote controller is linked to the aircraft. Specifications O3 (OcuSync 3.0) Operation Frequency Range 2.400-2.4835 GHz; 5.725-5.850 GHz*

Max Transmission Distance 12 km (FCC); 8 km (CE); 8 km (SRRC); 8 km (MIC)

(Unobstructed, free of interference) Transmission Power (EIRP) 2.400-2.4835 GHz:

32.0dBm (FCC); 18.5 dBm (CE) 18.5 dBm (SRRC); 18.5 dBm

(MIC) 5.725-5.850 GHz:

33.5dBm (FCC); 12.5 dBm (CE) 18.5 dBm (SRRC) Wi-Fi Protocol WiFi Direct, Wi-Fi Display, 802.11b/a/g/n/ac/ax 22 MIMO Operation Frequency Range 2.400-2.4835 GHz; 5.725-5.850 GHz*

Transmission Power (EIRP) 2.400-2.4835 GHz:

28.0dBm (FCC); 18.5 dBm (CE) 18.5 dBm (SRRC); 18.5 dBm (MIC); 18.5 dBm (KCC) 5.725-5.850 GHz:

28dBm (FCC); 12.5 dBm (CE) 24 dBm (SRRC); 12.5 dBm (KCC) Bluetooth Protocol Bluetooth 5.1 Operation Frequency Range 2.400-2.4835 GHz Transmission Power (EIRP) 6 dBm (FCC); 6 dBm(CE) 6 dBm (SRRC); 6 dBm (MIC); 6 dBm (KCC) 18650 Li-ion (5000 mAh @ 7.2 V) Recommended to use USB power adapters rated 12V or 15V General Battery Charging Type Rated Power Charging Time Operating Time 12 W 3 hours Storage Capacity ROM 32GB + expandable storage via microSD card 2.5 hours (using a USB power adapter rated 12V) Video Output Port Mini HDMI Port Operation Temperature Range

-20 to 40 C (-4 to 104 F) Storage Temperature Range Less than one month: -30 to 60 C (-22 to 140 F) One to three months: -30 to 45 C (-22 to 113 F) Three to six months: -30 to 35 C (-22 to 95 F) More than six months: -30 to 25 C (-22 to 77 F) Charging Temperature Range 5 to 40 C (41 to 104 F) Supported Aircraft Models**

Mavic 3, DJI Air 2S, Mavic Air 2 GPS+GLONASS Approx. 750 g RM510 GNSS Weight Model information.

* 5.8 GHz is unavailable in some countries due to local regulations.

** The Smart Controller V2.0 will support more DJI aircraft in future. Visit the official website for the latest FCC compliance statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. ISED compliance statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference. device.

(2) This device must accept any interference, including interference that may cause undesired operation of the Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 4W/kg averaged over 10 gram of tissue. The highest SAR value reported under this standard during product certification for extremity condition. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 4W/kg averaged over 10 gram of tissue. The highest SAR value reported under this standard during product certification for extremity condition. The user or bystander cannot touch or be within the closest distance evaluated for the SDR antennas while fully extended or in the 90 degree position. Cet quipement est conforme aux limites d'exposition aux rayonnements de l'ised pour les environnements non contrls.L'utilisateur final doit se conformer des instructions d'exploitation spcifiques afin de respecter la conformit l'exposition aux radiofrquences.Cet metteur ne doit pas tre au mme endroit ni fonctionner avec une autre antenne ou un autre metteur. L'quipement portatif doit tre conu de manire satisfaire aux exigences d'exposition aux ondes radio spcifies dans l'ised.Ces exigences fixent une limite SAR de 4 W / kg pour les tissus dpassant en moyenne 10 G.La valeur SAR la plus leve rapporte conformment la prsente norme pendant la certification du produit dans des conditions extrmes. Lorsque l'antenne SDR est compltement tendue ou en position de 90 degrs, l'utilisateur ou le spectateur ne peut pas toucher ou se trouver l'intrieur de la distance la plus proche value par l'antenne SDR.

cir DJI RC Pro 815 /Model:RM510 CMIIT ID: 2021AP7874 IC: 11805A-RM51021 FCCID: SSS-RMS5102T Powered by battery:7.2V == 5000mAh,36Wh CAN ICES-003(B) / NMB-003(B) ea This device complies with part 15 of the FCC rules, Operation is subject to the following two conditions:

(I)This device may not cause harmful interference, and

(2)This device must accept any interference received. Including interference that may cause undesired operation. SZ DJI TECHNOLOGY CO, LTD. RIITBARECIRAAIRAAD Address:l4th floor, West Wing, Skyworth Semiconductor Design Building NO.18 Gaoxin South 4th Ave,Nanshan District,Shenzhen, Guangdong,China RE aE-RNSIO PEE AIE/ Made in China Oe C AEE

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name SZ DJI TECHNOLOGY CO., LTD Address 14th floor, West Wing, Skyworth Semiconductor Design Building NO.18 Gaoxin South 4th Ave,Nanshan District, Shenzhen 518057, Guangdong,China Grantee Code SS3 FCC ID SS3-RM51021 Authorized Contact Name fajia wang Contact Email certification@dji.com Contact Phone +8675586152250 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date:2021-07-12 Print Name: fajia wang Title: PM *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

SZ DJl TECHNOLOGY CO., LTD Request for Class Il Permissive Change FCC ID: SS3-RM51021 Date: 2021-11-03 TO: Federal Communication Commission Please be notified that we, the undersigned, SZ DJI TECHNOLOGY CO., LTD declare that the reasons for this Class !| permissive change are as below:

Our product DJI RC Pro, model RM510, and RM510B are the same in circuit design, PCB layout, electrical components used, internal wiring and functions; The difference is that 5.1G

(5150-5250MHz) Wi-Fi is enabled on RM510B software, while RM510 is not enabled. Thank you. Sincerely. Print Name: fajia wang Title: PM in Woe Signature:

On behalf of Company: SZ DJI TECHNOLOGY CO., LTD Telephone: +8675586152250 E-mail: certification@dji.com

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Tune up procedure Software SZ DJI TECHNOLOGY CO., LTD TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: SS3-RM51021 SHORT TERM CONFIDENTIALITYAdditionally, the applicant requests the following documents be held confidential until the device is marketed or 180days from the grant date, whichever is less. If the device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: fajia wang Title: PM Signature: On behalf of Company: SZ DJI TECHNOLOGY CO., LTD Telephone: +8675586152250 E-mail: certification@dji.com

SZ DJI TECHNOLOGY CO., LTD Date: 2021-07-12 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: SS3-RM51021 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch and Kobe Jian in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with SZ DJI TECHNOLOGY CO., LTD This authorization is valid until further written notice from the applicant. Print Name: fajia wang Title: PM Signature: On behalf of Company: SZ DJI TECHNOLOGY CO., LTD Telephone: +8675586152250 E-mail: certification@dji.com

SZ DJI TECHNOLOGY CO., LTD TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: SS3-RM51021 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions BOM List Tune up procedure Software Security Description The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180days from the grant date, whichever is less. If the device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: fajia wang Title: PM Signature: On behalf of Company: SZ DJI TECHNOLOGY CO., LTD Telephone: +8675586152250 E-mail: certification@dji.com

SZ DJI TECHNOLOGY CO., LTD We, SZ DJI TECHNOLOGY CO., LTD declare that this EUT (FCC ID: SS3-RM51021) doesnt have ad Hoc Mode function on US/Canada frequencies. In addition, the frequency selection feature is disabled by firmware for devices marketed to the US/ Canada. For DTSWi-Fi part of this device, only channels 1-11 will be used in North America. Country code selection is disabled. Should you have any questions or comments regarding this matter, Please have my best attention. Sincerely yours, Print Name: fajia wang Title: PM Signature: On behalf of Company: SZ DJI TECHNOLOGY CO., LTD Telephone: +8675586152250 E-mail: certification@dji.com