FCC ID: SS3-RD241608RF Forward Phased Array Radar

Agras T25 Quick Start Guide v1.0 2022.12 Aircraft The Agras T25 aircraft has a truss-style body that comes with pitched arms that can be folded, making it easier to transport. The integrated spraying system can quickly transform into the spreading configuration with a spreading payload of 25 kg. The aircraft is equipped with the phased array radar system and binocular vision system, including downward and forward binocular vision, forward and rear phased array radar. The systems provide 360-degree omnidirectional obstacle sensing to ensure operational safety. The ultra HD FPV camera with a tiltable gimbal can automatically collect HD field images for local offline reconstruction to assist precise field planning. The Coaxial Dual Propeller structure brings a strong wind field. Pesticides can penetrate thick canopies to allow thorough spraying. The spraying system is equipped with the Magnetic Drive Impeller Pump, Dual Atomized Sprinkler, Anti-Drip Centrifugal Valve and solenoid valve, to ensure more efficient and precise pesticide spraying, as well as save liquid pesticide. The spraying system can be upgraded with two more sprinklers to meet different operation scenarios. 13. Forward Binocular Vision 14. Spotlights 15. Forward Phased Array Radar 16. Rear Phased Array Radar 17. Landing Gear 18. Intelligent Flight Battery 19. Onboard D-RTKTM Antennas 20. Internal OCUSYNCTM Image Transmission Antennas 21. External OcuSync Image Transmission Antennas 22. Aircraft Status Indicators (on two rear arms) 1. Propellers 2. Motors 3. ESCs 4. Aircraft Front Indicators (on two front arms) 5. Frame Arms 6. Folding Detection Sensors (built-in) 7. Spray Lance 8. Sprinklers 9. Spread Tank 10. Delivery Pumps 11. FPV PTZ camera 12. Downward Binocular Vision Using the T25 Preparing the Intelligent Flight Battery Only use official DJI flight batteries. Check the battery level before flying and charge according to the corresponding manual document. Preparing the Aircraft Unfold the M3 and M4 arms, and fasten the two arm locks. Avoid pinching fingers. Unfold the M1 and M2 arms, and fasten the two arm locks. Avoid pinching fingers. Unfold the propeller blades. Insert the Intelligent Flight Battery into the aircraft until you hear a click. Make sure that the battery is firmly inserted into the aircraft. Only insert or remove the battery when the aircraft is powered off. To remove the battery, press and hold the clamp and lift the battery up. Fold the M1 and M2 arms followed by the M3 and M4 arms. Otherwise, the arms may be damaged. Getting Ready for Takeoff A. Place the aircraft on open, flat ground with the rear of the aircraft facing toward you. B. Make sure that the propellers are securely mounted, there are no foreign objects in or on the motors and propellers, the propeller blades and arms are unfolded, and the arm locks are firmly fastened. C. Make sure that the spray tank and flight battery are firmly in place. E. Power on the remote controller, make sure that the DJI Agras app is open, and power on the aircraft. Tap Start in the home screen of the app to enter Operation View. Make sure that the GNSS signals are strong and the screen shows Ready to GO (GNSS) or Ready to GO (RTK). Otherwise, the aircraft cannot take off. RTK positioning is recommended. In the app, go to Operation View, tap

> RTK, and select a method for receiving RTK signals. Calibrating the Flow Meter Make sure to calibrate the flow meter in the following situations:

Change liquid payload with different viscosity. The difference between the actual area and planned area is more than 15% after the first operation. Calibrating procedure A. Get Ready to Calibrate Fill the spray tank with approximately 2 L of water. Press the Spray button to start or stop spraying manually in order to exhaust air. B. Calibrating the flow meter In the app, go to Operation View, tap

, then tap Calibration on the right of the flow meter calibration section. Tap Start Calibration and calibration will start automatically. The result of the calibration will be displayed in the app when completed. After calibrating successfully, users can proceed with the operation. If calibration fails, tap the reminder to view and resolve the problem. Afterwards, recalibrate and wait for successful calibration. Flight In order for the aircraft to automatically take off and perform an operation, it is recommended to creat a plan for a field and select an operation before takeoff. Refer to the Starting Operations section for more information. For other scenarios, take off and land manually as follows. Takeoff Perform a Combination Stick Command (CSC) and push the throttle stick up to take off. O R Landing Throttle Stick (left stick in Mode 2) Push the throttle stick down until the aircraft lands. There are two methods to stop the motors after landing. Method 1: When the aircraft has landed, push and hold the throttle stick down. The motors will stop after three seconds. Method 2: When the aircraft has landed, push the throttle stick down, and perform the same CSC that was used to start the motors. Release both sticks once the motors have stopped. Spinning propellers can be dangerous. Stay away from spinning propellers and motors. DO NOT start the motors in confined spaced or where there are people nearby. Maintain control of the remote controller as long as the motors are running. DO NOT stop the motors mid-flight. Otherwise, the aircraft will be crashed. Stop the motors only in an emergency situation to reduce the risk of damage or injury. It is recommended to use Method 1 to stop the motors. When using the Method 2 to stop the motors, the aircraft may roll over if it is not completely grounded. Use Method 2 with caution. After landing, power off the aircraft before turning off the remote controller. Starting Operations Users can perform aerial surveying for the operation area in the DJI Agras app, receive an HD map via offline reconstruction in the remote controller. Field planning and identifying can be performed on the HD map before route operation. The following descriptions use Crosshair and Route Mapping and Route Mode as an example. 1. Power on the remote controller and then the aircraft. Enter Operation View in the DJI Agras app. 2. Tap Mode button on the upper left corner and select Route Mapping in the Mapping panel. 3. Tap on the bottom right of the sreen and select Area Route or Boundary Route.Then tap in middle of the right screen to select Crosshair in the Add Point list. 4. Drag the map and tap Add to add a point at the crosshairs. Tap to save. 5. Tap and move the slider to launch the aircraft. The aircraft will perform the mapping operation along the route and land automatically. 6. Wait for the app to complete reconstruction. The reconstruction result will be displayed on the original map. 7. Tap Identify Field, then tap an identified field to select it and adjust the boundary. 8. Tap Mode button on the upper left and select Route in the Agriculture panel. 9. Tap on the left and select a field in the field list. 10. Tap Edit to edit field and set route parameters. Drag to adjust the flight direction of the route. Then save. 11. Tap to use the field. Set task parameters and tap to save. 12. Tap

, check the aircraft status and task settings, and move the slider to take off. The aircraft will perform the operation automatically. Only take off in open areas and set an appropriate Connection Routing and RTH Altitude according to the operating environment. An operation can be paused by moving the control stick slightly. The aircraft will hover and record the breakpoint. After that, the aircraft can be controlled manually. Select the operation again to continue. The aircraft will return to the breakpoint automatically and resume the operation. Pay attention to aircraft safety when returning to a breakpoint. In Route and Fruit Tree Operation modes, the aircraft is able to circumvent obstacles, which is disabled by default and can be enabled in the app. If the function is enabled and the aircraft detects obstacles, the aircraft will slow down and circumvent the obstacles and return to the original flight path. Users can set the action the aircraft will perform after the operation is completed in the app. More Operation Modes and Functions Refer to the user manual for more information about the A-B Route Operation, Manual Operation, and Fruit Tree modes, and on how to use functions such as Connection Routing, Operation Resumption, System Data Protection, and Empty Tank. Specifications Aircraft (Model: 3WWDZ-20B) Operating Frequency 2.4000-2.4835 GHz 5.725-5.850 GHz Transmitter Power (EIRP) 2.4 GHz: <33 dBm (FCC), <20 dBm (CE/SRRC/MIC) 5.8 GHz: <33 dBm (FCC), <23 dBm (SRRC), <14 dBm (CE) RTK/GNSS Operating RTK: GPS L1/L2, GLONASS F1/F2, BeiDou B1I/B2I/B3I, Galileo E1/E5b, Frequency QZSS L1/L2 GNSS: GPS L1, GLONASS F1, BeiDou B1I, Galileo E1, QZSS L1 Operating Temperature 0 to 45 C (32 to 113 F) Forward Phased Array Radar (Model: RD241608RF Operating Frequency 24.05-24.25 GHz (NCC/FCC/MIC/KC/CE) Power Consumption 23 W Transmitter Power (EIRP)

<20 dBm (NCC/MIC/KC/CE/FCC) Operating Voltage DC 15 V Operating Temperature 0 to 45 C (32 to 113 F) Rear Phased Array Radar (Model: RD241608RB Operating Frequency 24.05-24.25 GHz (NCC/FCC/MIC/KC/CE) Power Consumption 18 W Transmitter Power (EIRP)

<20 dBm (NCC/MIC/KC/CE/FCC) Operating Voltage DC 15 V Operating Temperature 0 to 45 C (32 to 113 F) Compliance Information FCC Statement:

Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. ISED Statement:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with FCC& RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ce matriel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102 nonce dans un autre environnement.cette eqipment devrait tre install et exploit avec distance minimale de 20 entre le radiateur et votre corps. EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device(RD241608RF /RD241608RB) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

2.75mm ITASCA AIR AB) SZ DJI TECHNOLOGY CO.,LTD. Address:Lobby of T2, DJl Sky City, No. 53 Xianyuan Road, Xili Community, Xili Street, Nanshan District, Shenzhen, China.

[Grsvmncne a ow 23000 C) ANATEL ORK CEMA} @ Ko ECGID: SSS RO Ss1SOBRE CAN ICES-003(A) / NMB-003(A) IC: N18OSA-RD241608RF This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made In China Nis 4 5 6 7 8 9 1011 12 13 14 15 1617

SZ DJI TECHNOLOGY CO., LTD. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: SS3-RD241608RF To whom it may concern:

Date: 2023/6/12 We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with << SZ DJI TECHNOLOGY CO., LTD.>>. This authorization is valid until further written notice from the applicant. Name (Printed): Gary Zeng Title: PM Signature:

On behalf of Company: SZ DJI TECHNOLOGY CO., LTD. Telephone: +8675586152250

SZ DJI TECHNOLOGY CO., LTD. To:

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: SZ DJI TECHNOLOGY CO., LTD. Lobby of T2, DJI Sky City, No. 53 Xianyuan Road, Xili Community, Xili Street, Nanshan District, Shenzhen, China. Regarding:

Confidentiality Request regarding application for FCC ID: SS3-RD241608RF LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature:

Printed Name: Gary Zeng Title: PM Company Name: SZ DJI TECHNOLOGY CO., LTD.

UNITED STATES DESIGNATED AGENT LETTER Date: 2023-06-06 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant Company Name:

Grantee Code:

Contact Name:

Address:

City/Province/Zip:

Telephone:

Fax:

Email:

SZ DJI TECHNOLOGY CO., LTD SS3 Gary Zeng Lobby of T2, DJI Sky City, No 53 Xianyuan Road, Xili Community,Xili Street,Nanshan District, Shenzhen 8675586152250

+86 755 86965903 certification@dji.com ATTN: Director of Certification:

U.S. designated agent Company Name:

FRN:

Contact Name:

Address:

DJI Research LLC 0033569757 Jie Shen 435 Portage Ave, Palo Alto, CA 94306 City/Province/Zip:

Telephone:

Fax:

Email:

Palo Alto/California/94306 530-574-9905 jack.shen@dji.com We, < SZ DJI TECHNOLOGY CO., LTD > and < DJI Research LLC > understand and acknowledge the applicants consent and the designated agents obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, < SZ DJI TECHNOLOGY CO., LTD > and < DJI Research LLC > acknowledge the applicants acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Gary Zeng Name (Printed): Jie Shen Title: PM Signature:

Title: General Manager Signature:

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name SZ DJI TECHNOLOGY CO., LTD. Address Grantee Code FCC ID Lobby of T2, DJI Sky City, No. 53 Xianyuan Road, Xili Community, Xili Street, Nanshan District, Shenzhen, China. SS3 SS3-RD241608RF Authorized Contact Name Gary Zeng Contact Email Contact Phone certification@dji.com

+8675586152250 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, c) d) e) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) g) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List

[SZ DJI TECHNOLOGY CO., LTD.] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules.

[SZ DJI TECHNOLOGY CO., LTD.] (the applicant) certifies that, as of the date of the filing of the application, the applicant [ is not]

identified on the Covered list, established pursuant to 1.50002, as an entity producing covered equipment. Applicant Signature:

Date:2023/6/12 Print Name:

Title:

Gary.Zeng PM

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database QSF27-14-04 Rev 1.0 Rev. Feb 6, 2023 Page 1 of 1 Original Issue: Jan. 4, 2021