OSMO Mobile Quick Start Guide V1.0
Osmo Mobile The OSMOTM Mobile is a professional mobile phone gimbal that stabilize your phone while in motion. Powerful features such as ActiveTrack and Motion Timelapse are available through the DJI GO app.
OSMO Mobile www.dji.com 1 Mobile Phone Holder 2 Pan Motor 3 Camera Status LED 4 Joystick 5 Shutter Button 6 Record Button 7 Power Switch 8 System Status LED 9 Tilt Motor 10 Adjustable Arm 11 Mobile Phone Detect Sensor 12 Adjustable Arm Lock Knob 13 Roll Motor 14 Holder Lock Knob 15 Charging/Upgrade Port 16 Trigger 17 DJI Rosette Mount 18 Lanyard Hole 19 Battery Cover 1. Install the DJI GO App Search for DJI GO on the App Store or Google Play, and install the app on your mobile phone. 3. Mount and Balance the Mobile Phone Loosen the Holder Lock Knob, place the mobile phone in the mobile phone holder and tighten the knob to secure its position.
DJI GO supports iOS 8.0 (or later) and Android 4.3 (or later). 2. Prepare the Battery Fully charge the battery before using it for the first time to activate it. Insert the battery as shown. Battery Level High Low To balance the system, place the Osmo Mobile and mobile phone on a level surface as shown. The system is balanced if the mobile phone remains level when released, balanced only by the gimbal. A. If the roll axis tilts to the left, loosen the Adjustable Arm Lock Knob and pull out the arm until the roll axis remains level. B. If the roll axis tilts to the right, adjust the mobile phone to the left until the roll axis levels out.
4. Connect to the DJI GO App Enable Bluetooth on your mobile phone To Power On:
Pull down on the switch Pull down again > Sleep Pull down and hold for 1.5 s > Power Off
Launch the DJI GO app and tap Enter Camera View. Tap and then follow the instructions to connect to the Osmo Activate the Osmo Mobile when using it for the first time. This requires an internet connection. Internet 5. Controls
Use the joystick to pan or tilt the mobile phone.
Record Button: Press once to start recording, and again to stop recording.
Shutter Button: Press once to take a photo. Press and hold for burst capture.
Trigger Hold down to enable Lock Mode. Tap twice to center the mobile phone. Tap three times to switch between the mobile phones front and rear cameras. Specifications
Handle Dimensions Weight (battery included)
Gimbal Name Dimensions Weight Consumption Angular Vibration Range Controllable Range Mechanical Range 2.4 x 1.9 x 6.4 inch
(61.8 x 48.2 x 161.5 mm) 201 g Zenmuse M1 125.06 x 109.15 x 90.98 mm (Folded) 300 g Static: 2.2 W; Dynamic: 3 W 0.03 Pan: 150 Roll: 25 Tilt: -125 to +35 Pan: 165 Roll: -50 to +90 Tilt: -140 to +50 120/s Max Controllable Speed Mobile Phone Width Range 2.31-3.34 inch (58.6-84.8 mm). Minimum width approx. that of the iPhone 5S, Maximum width approx. that of the Huawei Mate 8 Max
Wireless Model
Intelligent Battery Model Type Capacity Energy Voltage
Bluetooth Low Energy 4.0 HB01-522365 LiPo 980 mAh 10.8 Wh 11.1 V
For more information, read the User Manual:
www.dji.com/product/osmo-mobile To charge the Osmo Mobile, connect the USB adapter (not included) to the charging port using the provided power cable.
Do not power on the Osmo Mobile without a mobile phone. The Osmo Mobile will not work if no device is detected by its sensor.
It is important to balance the mobile phone in order to achieve optimal performance. The Osmo Mobile should only be balanced when powered off. DJI GO advanced features:
This Quick Start Guide is subject to change without prior notice. ActiveTrack Motion Timelapse OSMOTM is a trademark of DJI. Copyright 2016 DJI All Rights Reserved. Printed in China FCC Compliance Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC RSS Warning This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure Information:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limitesd'exposition de rayonnement RF IC tabliespour un environnement non contrl. Cetmetteur ne doit pas tre co-implant oufonctionner en conjonction avec toute autreantenne ou transmetteur. CAN ICES-3 (B)/NMB-3(B) EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby dec compliance with the essential requirements and other relevant provisions of the R&TTE Directive. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance EU contact address: DJI GmbH, Industrie Strasse. 12, 97618, Niederlauer, Germany