FCC ID: CASTEL0057 Mobile Transceiver

T2000 INSTALLATION GUIDE TAIT ELECTRONICS LIMITED Software licence agreement This legal document is an Agreement between you, (the Licencee) and Tait Electronics Limited (Tait). By opening this product package and/or using the product you agree to be bound by the terms of this Agreement. If you do not agree to the terms of this Agreement, do not open the product package and immediately return the unopened product package to Tait. If you open the product package that will be deemed to be acceptance of the terms of this licence agreement. Licence In consideration of the payment of the Licence Fee which forms part of the price you paid for products you acquired from Tait or its subsidiary or agent (the products) and our willingness to be bound by the terms of this agreement, Tait grants to you as Licencee the non-exclusive right to use the copy of a Tait software program included in the products, (the Software). In particular the Licencee may use the program on a single machine and if the software is supplied on a diskette, the licensee may:

(a) copy the program into any machine readable or printed form for backup purposes in support of your use of the program on the single machine

(Certain programs, however, may include mechanisms to limit or inhibit copying. They are marked copy protected), provided the copyright notice must be reproduced and included on any such copy of the Software.

(b) Merge it into another program for your use on the single machine. (Any portion of this program merged into another program will continue to be subject to the terms and conditions of this Agreement.);

The Licencee may not duplicate, modify, reverse compile or reverse assemble the Software in whole or part. Title to software This agreement does not constitute a contract of sale in relation to the Software supplied to the Licencee. Not withstanding the Licencee may own the magnetic or other physical media on which the Software was originally supplied, or has subsequently been recorded or fixed, it is a fundamental term of this Agreement that at all times title and ownership of the Software, whether on the original media or otherwise, shall remain vested in Tait or third parties who have granted licences to Tait. Term and termination This Licence shall be effective until terminated in accordance with the provisions of this Agreement. The Licencee may terminate this Licence at any time by destroying all copies of the Software and associated written materials. This Licence will be terminated automatically and without notice from Tait in the event that the Licencee fails to comply with any term or condition of this Agreement. The Licencee agrees to destroy all copies of the Software and associated written materials in the event of such termination. Limited warranty The Software is supplied by Tait and accepted by the Licencee as is without warranty of any kind either expressed or implied, including but not being limited to any implied warranties as to merchantability or fitness for any particular purpose. The entire risk as to the quality and performance of the Software vests in the Licencee. Should the Software prove to be defective, the Licencee (and not Licensor or any subsidiary or agent of the Licensor) shall assume the entire cost of all necessary servicing, repair or correction. Tait does not warrant that the functions contained in the Software will meet the Licencees requirements or that the operation of the Software will be uninterrupted or error free. However Tait warrants that the diskettes if any on which the Software is supplied to the Licencee shall be free from defects in material and workmanship under normal use and service for a period of ninety (90) days from the date of delivery to the Licencee. Exclusion of liability Taits entire liability and the Licencees exclusive remedy shall be:

1. 2. 3. 4. The replacement of any diskette not meeting Tait limited warranty and which is returned to Tait or an authorised agent or subsidiary of Tait with a copy of the Licencees purchase receipt; or If a diskette is supplied and if Tait is unable to deliver a replacement diskette which is free from defects in material or workmanship, the Licencee may terminate this Agreement by returning the Software to Tait. In no circumstances shall Tait be under any liability to the Licencee, or any other person whatsoever, for any direct or consequential damage arising out of or in connection with any use or inability of using the Software. Tait warrants the operation of the Software only with the operating system for which it was designed. Use of the Software with an operating system other than that for which it was designed may not be supported by Tait, unless otherwise expressly agreed by Tait. General The Licencee confirms that it shall comply with the provisions of law in relation to the Software. Law and jurisdiction This Agreement shall be subject to and construed in accordance with New Zealand law and disputes between the parties concerning the provisions hereof shall be determined by the New Zealand Courts of Law. Provided however Tait may at its election bring proceedings for breach of the terms hereof or for the enforcement of any judgement in relation to a breach of the terms hereof in any jurisdiction Tait considers fit for the purpose of ensuring compliance with the terms hereof or obtaining relief for breach of the terms hereof. No Dealings The Licencee may not sublicense, assign or transfer the licence or the program except as expressly provided in this Agreement. Any attempt otherwise to sublicense, assign or transfer any of the rights, duties or obligations hereunder is void. No Other Terms The Licencee acknowledges that it has read this agreement, understand it and agree to be bound by its terms and conditions. The Licencee further agrees that this is the complete and exclusive statement of the agreement between it and Tait in relation to the Software which supersedes any proposal or prior agreement, oral or written and any other communications between the Licencee and Tait relating to the Software. (LS-589) Contents Components of the T2000II Radio Kit ........................... 1 Recommended Installation Tools ................................. 1 Installation of your Radio .......................................... 2 Installation Planning ........................................................... 2 To Disassemble the Cradle .................................................. 2 Mounting ............................................................................. 3 To Reassemble the Cradle ................................................... 3 Antenna Installation ............................................................ 4 Wiring ................................................................................. 6 External Speaker ........................................................... 6 Power Cable .................................................................. 6 External Wire (Horn/Hush/Emergency) ............................... 7 Remote Control Head Option .............................................. 7 Microphone Clip .................................................................. 8 Installation Checks .............................................................. 8 Components of the T2000II Radio Kit The T2000II Radio kit includes the following parts:

T2000II Radio Unit

Microphone

Complete Cradle

4 Ohm Speaker (not for internal speaker models)

Installation Kit:

BNC Antenna Crimp Plug

Cradle Keys (2)

Power Cable (5m)

- Two-way hermaphroditic connector (1)

- Socket receptacle (2)

- 10A 12V Blade fuse (2)

- Inline crimp fuse holder (2)

- Self tapping screw (4)

- Shakeproof washer (4)

- Microphone clip kit (1)

- Control head mounting bracket (T2020II and T2040II only) Recommended Installation Tools

Portable Drill

Centre Punch

Drill Bits: 4mm for self-tapping screws, 6mm for nuts and bolts

Pozidriv Screwdrivers

BNC Crimp Tool (e.g. Transradio England Duo crimp 894)

In-line Power Meter capable of measuring forward and reflected power at the operat-

ing frequency of the radio

Hammer 1 Installation of your Radio Installation Planning To ensure trouble-free, efficient installation, inspect the vehicle and determine how and where the antenna, radio and accessories are to be mounted. It is possible to remote-mount the T2020II, T2040II and T2050II models as these have alphanumeric keypads, with the control head separate from the radio chassis. This enables the radio to be mounted in a discrete location, e.g. the rear luggage space, with the control head mounted in a convenient position for the vehicles occupants. See the M2000 service manual, available from your Tait dealer, for details of this modification. Occupants Safety Check that the chosen locations for the radio and accessories do not endanger the vehicle occupants. Overhead mounting is not recommended, especially without an additional safety strap. Check that the radio may be conveniently operated when seat belts are worn. Caution: To prevent interference with vehicle electronic systems (such as ignition and anti-skid devices), the radio, its antenna and wiring should be mounted away from these units and their associated cables. Allow sufficient airflow around the radio to permit adequate cooling. Once you have found a suitable mounting position for the radio, hold it (fitted in the cradle) in the proposed mount-

ing position and check there is clearance behind it for the heatsink, cables, etc. Check that the position provides a large enough flat surface that the cradle will not be distorted. To Disassemble the Cradle 1 Remove the radio from its cradle by sliding the plastic key supplied with the radio fully into the slot on the left front of the radio unit. The radio will now slide out forwards from the cradle, as shown below:

Cradle Radio unit Plastic key 2 Figure 1: Cradle and Key 2 Disassemble the cradle by placing it on a firm surface and applying pressure down on one of the middle ribs of the plastic side moulding with a screwdriver. This will release the ribs along this edge from the slots in the metal cover with which they mate. A similar approach will release the other edge of the metal cover which can now be lifted clear (as shown below). Figure 2: Cradle Disassembly Mounting 1 Hold the drilled half of the metal cradle cover in the position chosen for the radio and use the four cradle cover mounting holes as a template to mark the locations for drilling. Ensure that drilling at the selected points will not damage existing wiring. 2 Indent the drilling positions with a centre punch and drill 4mm holes for self-tapping screws, or 6mm holes for nuts and bolts. Reduce the hole size if using self-tapping screws in metal which is less than 1mm thick. 3 Drill any additional holes required for cables and fit them with suitable grommets or bushings. 4 Secure the metal cradle cover to the mounting points with the M5 self-tapping screws supplied, or with M5 nuts and bolts. Ensure that tightening the screws or bolts does not distort the cradle. To Reassemble the Cradle 1 Reassemble the cradle by clipping one plastic side moulding to each side of the mounted metal cover (as shown in Figure 3). Take care to locate the ribs on the plastic part in the slots on the shoulders of the metal cover. They will only fit one way round. 3 2 Take the remaining metal cover and fit it over the exposed edges of the side mould-

ings, again taking care to align the ribs with the slots. Clip it securely home. Figure 3: Cradle Reassembly Antenna Installation To comply with FCC RF exposure limits, this product must be installed using a 4.5 dBi gain antenna. 1 Terminate one end of the coaxial cable at the antenna. Good quality 50 ohm coaxial cables such as RG58 or UR76 are suitable. Run the free end of the coaxial cable to the radios mounting position and cut it to length allowing 200mm to 300mm excess. 2 Terminate the free end of the cable with the BNC crimp plug supplied, as shown in Figure 4:

- Fit the crimp sleeve over the cable sheath.

- Trim the outer sheath from the cable to 15mm.

- Trim the braid to 8.5mm.

- Trim the dielectric to 11mm. (Take extreme care not to nick the centre conductor with the trimming device.)

- Fit the male pin onto the centre conductor with the shoulder pressed against the end of the dielectric. 4

- Crimp the male pin onto the centre conductor.

- Press the assembly firmly into the rear of the plug. (Check that no braid gets trapped between the dielectric and the inside of the plug.)

- Slide the crimp sleeve over the braid and press against the shoulder of the plug.

- Crimp the crimp sleeve onto the braid and plug body. Crimp Sleeve aaaaaaaa bbbbbbbb aaaaaaaa bbbbbbbb aaaaaaaa bbbbbbbb aaaaaaaa bbbbbbbb Male Pin Plug Figure 4: Antenna Connector Assembly Wiring External Speaker Some T2000II models are fitted with internal speakers. However it is possible to fit an external speaker if required, by terminating a twin wire in the power connector. To disable the internal speaker, cut the link on the power connector as shown in Figure 5. T2000II models with no internal speaker must have an external speaker fitted. The power connector comes pre-wired with the speaker cable. Mount the external speaker in a convenient location close to the operator. Run the free end of the speaker wire to the speaker, and connect it to the speaker plug. Ignition External Power Supply

+13.8V Ground Internal Speaker Link

(cut to disable) Ground Live }External Speaker Figure 5: Power Connector Wiring 5 Power Cable 1 Disconnect the vehicles battery unless specifically prohibited from doing so by the customer, vehicle manufacturer, agent or supplier. In this event, exercise extreme caution throughout the installation and fit the fuses only when the installation is complete. Caution: Always disconnect the radios power lead before connecting a second battery or using power from another vehicle (e.g. when jump-starting the vehicle). 2 Determine where the battery leads will be routed. 3 Cut the negative and the positive wires where the in-line crimp fuse holders will be placed (as close to the battery as practicable). 4 Insert each end of the negative wire into one of the in-line crimp fuse holders and crimp them to force the metal contacts onto the wires. Terminate the wire at the battery earth. 5 Repeat Step 4 for the positive wire and terminate it at the positive terminal of the battery. Caution: Prevent the power wires chafing on any metal parts. Note: T2000II radios are designed to operate from a nominal 12V negative earth supply, and require currents of up to 8A. (The radios will tolerate a supply voltage range of 10.8V to 16.0V). In vehicles with a 24V electrical system (e.g. many trucks), it is essential to provide a suitably rated 24/12V converter (e.g. Tait T2007) to isolate the radio from the battery and protect it against excessive voltages. 6 If the economizer is to be controlled by the ignition line, terminate a wire in the power connector and connect the ignition wire to a +12V supply which is live only when the vehicles ignition is switched On. External Wire (Horn/Hush/Emergency) The T2000II can be configured to operate the vehicles horn, radio or a hidden switch:

1 Terminate a suitable length of wiring in the external port of the power connector. 2 Run the free end of the external wire from the power connector to the appropriate vehicle wiring. The options interface is usually configured to switch or be switched in the ground state. Confirm the exact operation in the documentation supplied with the interface unit. 6 Remote Control Head Option The control head of some T2000II models may be supplied ready for mounting remotely from the radio chassis. In this case the control head should be located away from direct sunlight, and the cable connecting it to the radio should be routed away from the antenna with care taken to ensure that the cable will not be subject to damage. If it is necessary to run the cable through a bulkhead or similar obstruction, you may unplug the cable from the control head as follows:

1 Unscrew the rear of the control panel and lift off the rear cover, taking care not to lose the two nuts located on each end. 2 Disconnect the red connector from the printed circuit board socket to free the cable. 3 Route the cable as required, fitting grommets where necessary to prevent chafing of the cable insulation. 4 Fit the red connector to the printed circuit board socket the connector is shaped so that it can be fitted in the correct orientation only. 5 Refit the cable to the cable clamp on the rear cover and slip the two nuts into the receptacles at each end of the rear cover. 6 Refit the rear cover and replace the cover screws, tightening them carefully. Do not overtighten the screws. The control head can now be installed as follows:

1 Mount the bracket for the control panel on a flat surface using the self-tapping screws supplied. 2 Place the control head in the bracket, position it for a good viewing angle, and fit the 2 screws to secure it in place. Microphone Clip The microphone clip must be earthed (to the negative supply line) if hookswitch control of monitoring, scanning or call termination is to operate. Refer to the radios operating in-

structions to confirm requirements. Ensure that the microphone clip is mounted in a position where the microphone PTT key cannot be inadvertently activated or jammed on. 7 Installation Checks 1 Plug the microphone into the socket on the lower left-hand corner of the radios front panel. Push the cable grommet into the rectangular aperture in the panel. 2 Insert the fuses into the power lead. 3 Switch on the radio and confirm that it is operational. 4 Connect an in-line power meter between the radio and the antenna and measure the forward and reflected power levels. Less than 1W should be reflected for 25W forward power. If this is not achieved, check the installation including antenna length. 5 Make a call to another party on the radio (as described in the operating instructions). Tait Electronics has made every effort to ensure the accuracy of information in this manual. However, Tait Electronics reserves the right to update the radio and / or this manual without notice. 8 Excellence in Radio Communications CORPORATE HEAD OFFICE NEW ZEALAND Tait Electronics Ltd P.O. Box 1645, Christchurch Phone : (64) (3) 358-3399 Fax : (64) (3) 358-0340 AUSTRALIA Tait Electronics (Aust) Pty Ltd Phone : (61) (7) 3865-7799 Fax : (61) (7) 3865-7990 Toll Free : (1-300) 304-344 E-mail: australia@taitworld.com CANADA Tait Mobile Radio Inc Phone : (1) (905) 472-1100 Fax : (1) (905) 472-5300 Toll Free : (1) 1-800-890-8248 E-mail: canada@taitworld.com LATIN AMERICA Tait Latin America Phone : (1) (305) 260-9900 Fax : (1) (305) 260-9209 E-mail: latinamerica@taitworld.com NEW ZEALAND Tait Communications Ltd Phone : (64) (3) 348-3301 Fax : (64) (3) 343-0558 E-mail: newzealand@taitworld.com USA Tait Electronics (USA) Inc Phone : (1) (713) 984-8684 Fax : (1) (713) 468-6944 Toll Free : (1-800) 222-1255 E-mail: usa@taitworld.com TAIT EUROPE Regional Head Office UNITED KINGDOM Tait Europe Ltd Phone : (44) (1480) 52255 Fax : (44) (1480) 411-996 E-mail: unitedkingdom@taitworld.com FRANCE Tait France S.A.R.L. Phone : (33) (1) 41-14-05-50 Fax : (33) (1) 41-14-05-55 E-mail: france@taitworld.com GERMANY German Office Phone : (49) (911) 2870-7064/7160 Fax : (49) (911) 2870-7077 E-mail: germany@taitworld.com TAIT NORTH ASIA Regional Head Office HONG KONG Tait Mobile Radio (Hong Kong) Ltd E-mail: hongkong@taitworld.com Phone : (852) 2369-3040 Fax : (852) 2369-3009 BEIJING Tait Mobile Radio (Hong Kong) Ltd Phone : (86) 10-6510-2680 Fax : (86) 10-6510-2686 E-mail: beijing@taitworld.com TAIWAN Tait Mobile Radio (Taiwan) Ltd Phone : (886) 2-2731-1290 Fax : (886) 2-2-711-6351 E-mail: taiwan@taitworld.com TAIT SOUTH EAST ASIA Regional Head Office SINGAPORE Tait Electronics (Far East) Pte Ltd Phone : (65) 471-2688 Fax : (65) 479-7778 E-mail: singapore@taitworld.com THAILAND Tait Mobile Radio Ltd Phone : (662) 267-6290 Fax : (662) 267-6293 E-mail: thailand@taitworld.com 11/00 IPN: 429-20000-06

T2040 II Users Guide T2000 II ON/OFF - Volume knob PTT key Transmit indicator Display window Scrolling available indicator Service indicator T2000 BUSY TX WAIT GO SVC a 3 6 PQRS WXYZ 9 Keypad Microphone socket Function key Status key Despatcher key Alphanu m eric key Scroll keys Clear key Enter key Getting Started Introduction Your T2040II is controlled by a microprocessor which allows it to be configured to suit the needs of your particular fleet. This Users guide provides a brief description of the basic features of your radio. For information about the advanced features, a comprehensive operators manual is available from your Tait dealer. Switching on Turn the ON/OFF-Volume knob clockwise about one-third of a turn. You may need to finally adjust the volume when you receive your first call. Checking Check to see that the SVC (service) indicator System appears in the display within a few seconds, Availability showing that your radio has logged on to the network. There are three possible indications:

SVC Indicator Continuous Blinking Absent Meaning Your radio has access to a network and is ready to make or accept calls. Your radio does not currently have access to a network. It is attempting to find a site it is authorised to use, or it may be out of range of a network signal. Your radio is in Conventional mode. The radio is fitted with a preprogrammed timer to limit the maximum length of transmissions. When this time limit is reached, a three tone warning is sounded and transmission stops. You must release the PTT key before proceeding. Making a Call Receiving a Call Sending a Call There are four ways to make a call using your T2040II:

1 Enter the full number of the required party using the numeric keypad and then press the Hash

) key to send the call. 2 Enter a two-digit short dial preset number using the numeric keypad and then press the Hash

) key to send the call. 3 Use the Despatcher (

) and Function ( Fn ) keys which may each be preprogrammed to send a call directly, when you apply a long press. The Despatcher (

grammed to call your base despatcher.

) key is usually prepro-

4 Use an alphanumeric label to select a call identity (see Alphanumeric Entry mode). You may hear call setup tones followed by a ringing tone similar to that of a telephone, and the WAIT indicator may be displayed. When the called party answers, the WAIT indicator is replaced by the GO indicator and you may proceed with your conversation. The PTT key on the side of the microphone Using the Microphone switches the radio between transmit and receive and PTT key modes. Each time the radio transmits, the TX indicator appears in the display. To speak, press the PTT key. Hold the microphone about 5cm from your mouth and pause briefly to ensure your first word is not cut off, then speak clearly. Release it to listen to the reply. When you receive a call your radio will alert you with a ringing tone like a telephone and the identity of the caller will be displayed as explained below. Responding You may accept a call by lifting the microphone to Calls from its clip, pressing the PTT key and identifying yourself (for example Mobile-9 Receiving). If you do not want to accept the call, press the Clear (

) key and the call will be cancelled. If the call is a group call, you will hear a single ring and then the caller will broadcast a message to all members of your group. It is not normally necessary to reply. The source of an incoming call or the Caller Identification callers identity is shown in the display as follows:

Display Label Example VEHICLE7 Preset Number 8 Call Number 23 System Message OFLT System Message System Message PHONE PABX Explanation The calling party is one of your preset numbers with a label preprogrammed into your radio. The calling party is one of your network stored preset numbers without a label preprogrammed into your radio. The calling party is in the same fleet as your radio but is not preprogrammed. The calling party is not in the same fleet as your radio and is not preprogrammed. A call from the PSTN (Public Switched Telephone Network). A call from the PABX (Private Automatic Branch Exchange). T2040II Transmit Timer Call Queuing Status Calls If you need to leave your T2040II unattended, you may have it save incoming calls as call-back messages for you to return later. To set call queuing on and have all calls except Setting Queuing On group, PABX and PSTN calls queued:

Press the Despatcher (

) key until the indicator beside it illuminates. Handling Saved Calls number of calls received and the identity of the When you return to your radio it displays the first caller. You may:

1 Return the displayed call by pressing the PTT key;

2 Discard the call by pressing the Clear (

3 Scroll to another message using the Up and

) keys and handle it as above;

Down (

) key;

4 Make a new outgoing call as normal. Cancelling You may restore the radio to normal operation Call Queuing by pressing the Despatcher (

) key again until Do Not Disturb the indicator beside it extinguishes. The radio will now alert you normally when a call is received. If you still have calls saved in the queue, they are preserved and you may recover them at any time by turning call queuing back on. You may set your T2040II to reject all incoming calls whilst allowing you to make calls out normally. The radio will display QUIET and callers will be given the unavailable response.

To set Do Not Disturb, dial *49#.

To cancel, dial #49# or press the Clear (

) key, and the QUIET message is removed from the display. Sending a Status Message Status calls permit the rapid exchange of simple messages without voice conversation. Your radio can have messages such as En route, At lunch and so on preprogrammed. To select and send a status message:

1 Press the Status ( STAT ) key and use the (

) scroll keys to select an appropriate message;

2 To send the message to your despatcher, press the Hash (

) key;

3 To send the message to any other party, press

) key, and then:

4 Press the Hash (

the Star (

Dial the identity number using the keypad, or;

Select an alphanumeric label for the call.

) key to make the call. Receiving a When you receive a status call, your T2040II Status automatically enters the Call Queuing mode. Message The status message value shows on the left of the display and the callers identity on the right. If the status message corresponds to a label which is preprogrammed into your radio, the indicator beside the Alphanumeric (

flashes. To view the label:

Press the Alphanumeric (

) key.

) key Alphanumeric Entry Mode To perform repetitive operations which require several keystrokes, your T2040II may be preprogrammed with alphanumeric labels. These labels, when recalled, can perform a series of operations such as sending a call. FCC RF Exposure Limits Selecting a To use preset sequences, select them by their Sequence label as follows:

1 Press the Alphanumeric (

Alphanumeric Entry mode.

) key to enter the Example 2 Locate the desired label by using the cursor and keys (

the label is displayed, or enter the label for the required party, using the keypad.

) to scroll through the list until 3 Press the Hash (

) or the PTT key to initiate the labelled action as it is preprogrammed. You want to call your base despatcher who has been assigned the label, BASE. The keystroke sequence and display might appear as follows:

Press Key Display Reads Explanation Most recent selection displayed Label not yet identified Label not yet identified New label identified BASE is called and the BASE number is displayed 2 ABC2 ABC 2 ABC 7 PQRS or PTT key Safety Training Information This product generates radio frequency energy during transmissions. This device must be restricted to work-related use in an occupational/controlled exposure environment. The radio operator must have control of the exposure conditions and duration of all persons exposed to the antenna of this transmitter to satisfy FCC RF exposure compliance. This device is not approved for general population use.

It must only be used with authorized accesso-

ries and antennas.

The operator must ensure that the minimum safe distance of 0.34m (14 inches) between persons and the antenna is not exceeded during transmissions.

Do not exceed a duty cycle ratio of 50% transmit mode to stand-by or receive modes. The radio is in transmit mode when the PTT key on the microphone is pressed and the TX indicator shows in the display window. Additional Safety Warnings

DANGER: SWITCH THE RADIO OFF AT PETROL FILLING STATIONS

DANGER: SWITCH THE RADIO OFF IN THE VICINITY OF EXPLOSIVE DEVICES (such as in a quarry that uses blasting techniques)

Use of a handheld microphone or a radio while driving could contravene the legislation that applies in your country or state. Please check the vehicle regulations of your own country. 459-20400-02