all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 1.80 MiB | December 07 2012 | |||
1 | Cover Letter(s) | December 07 2012 | ||||||
1 | Cover Letter(s) | December 07 2012 | ||||||
1 | External Photos | December 07 2012 | ||||||
1 | ID Label/Location Info | December 07 2012 | ||||||
1 | Internal Photos | December 07 2012 | ||||||
1 | Test Report | December 07 2012 | ||||||
1 | Test Setup Photos | December 07 2012 |
1 | Users Manual | Users Manual | 1.80 MiB | December 07 2012 |
P1. WARNING 1. CAUTION!
1. To prevent damage to the finish, DO NOT use any abrasives, sharp objects or harsh chemical products containing alcohol, petroleum solvents, acids or acetone to clean this lockset. To prevent damage to the sensitive electronic components, DO NOT allow any liquids to enter lockset while installing or cleaning. Do not attempt to disassemble any internal components of this lockset as this WILL void the limited warranty. Do not drop or hit /strike the lockset as excessive shock may result in permanent damage. Do not use sharp objects to press key buttons. It is STRONGLY recommended that you always create a written backup of the programming code and individual user codes. Please use the last page of this booklet as your reference. For your security, please remember to change this lockset's factory default programming code to a PERSONAL programming code prior to normal day-to-day use of this product. It is STRONGLY recommended that you use only ALKALINE BATTERIES to operate this product. 2. 2. 3. 4. 5. 6. P2. CONTENTS MAIN OPERATING INSTRUCTIONS.....................................................................................03 PROGRAMMING CODE AND USER CODE..........................................................................05 COMPONENTS............................................................................................................................06 INSTALLATION INSTRUCTIONS...........................................................................................08 SETUP MODE 01. HOW TO CHANGE PROGRAMMING CODE.25 02. HOW TO ADD AN USER CODE.........................................................................................26 03. HOW TO ADD A PROXIMITY CARD (RFID).................................................................27 04. HOW TO ADD A REMOTE CONTROL (RADIO FREQUENCY, RF).........................28 05. HOW TO ADD A SINGLE-USE USER CODE/ REMOTE CONTROL.........................29 06. HOW TO DELETE AN INDIVIDUAL EXISTING USER CODE...................................30 07. HOW TO DELETE AN INDIVIDUAL EXISTING REMOTE CONTROL....................31 08. HOW TO DELETE AN INDIVIDUAL EXISTING PROXIMITY CARD.......................32 09. HOW TO DELETE ALL EXISTING USER CODES AT ONCE......................................33 10. HOW TO DELETE ALL EXISTING PROXIMITY CARDS/ REMOTE CONTROLS AT ONCE...34 11. HOW TO DISABLE ALL EXISTING USER CODES (VACATION MODE)..................35 12. HOW TO DISABLE BUTTON SOUND (MUTE MODE)...................................................36 13. HOW TO SETUP AUTO-LOCK TIME DELAY.................................................................37 14. HOW TO ENABLE AUTO-LOCK MODE..........................................................................38 15. HOW TO ENABLE DOUBLE AUTHORIZATION MODE..............................................39 16. HOW TO RESTORE FACTORY SETTING.......................................................................40 17. HOW TO REPLACE BATTERIES OF REMOTE CONTROL........................................41 OPERATION MODE 01. HOW TO LOCK (i.e. TO ENABLE AUTO-LOCK)...........................................................42 02. HOW TO UNLOCK................................................................................................................43 03. SAFE MODE............................................................................................................................44 TROUBLESHOOTING GUIDELINE........................................................................................45 DECLARATIONS AND SAFETY STATEMENTS..................................................................49 DATA RECORDS.........................................................................................................................50 P3. MAIN OPERATING INSTRUCTIONS LED indicator Keypad Lock button Cancel button Key override Thumbturn This manual is intended for Electronic Deadbolt Lock/ Proximity Card Electronic Deadbolt/ Remote Control Electronic Deadbolt. Please be advised that this manual is set up for this specific unit and is not to be used with any other product. LED Indicator 1. Green light: Code entered is valid. 2. Red light: Code entered is invalid/ Under setup mode. 3. Yellow light: Low battery warning.
* All batteries should be replaced if yellow light flashes. Keypad 1. To unlock the lockset by entering a valid code. 2. To program the lockset. 3. When mis-typing codes during any process, press Cancel button to cancel the wrong codes and re-enter the correct codes if the yellow light is on or keeps flashing. 4. To lock the lockset by pressing Lock button. Key Override: To unlock the lockset by a valid key. Thumbturn: To lock or unlock the lockset manually. P4. MAIN OPERATING INSTRUCTIONS Inductive Zone LED Lock button Unlock button Inductive Zone (only available for Proximity Card Electronic Deadbolt) 1. 2. The proximity card we offer is the latest Radio Frequency Identification (RFID) Inductive zone is around the keypad. technology, compatible with standard Mifare -13.56 MHz. 3. Please contact the proximity card with the inductive zone. Remote Control (Radio Frequency, RF) (only available for Remote Control Electronic Deadbolt) 1. There is one unlock button and one lock button on the remote control. 2. We recommend the operating distance between the remote control and the lockset is within 50ft (15m.) This is maximum distance under the circumstance that no objects block the emission of the remote control toward the lockset. 3. The LED of the remote control will light on when holding the lock button on the remote for 3 seconds. P5. PROGRAMMING CODE AND USER CODE PROGRAMMING CODE 1. Only one programming code will be allowed, and the lockset can be programmed by entering the programming code. 2. A programming code is restricted to 6-digits in length only. The pre-set programming code is 1-2-3-4-5-6 (factory setting), please change it before operating the lockset. 3. The lockset can be unlocked by entering programming code. USER CODE 1. A user code can be from four (4) to six (6) digits in length. 2. A user code can be changed (added or deleted) by accessing the setup mode. 3. The lockset cannot be programmed by entering the user code. 4. The lockset will unlock by entering the user code. Note:
User code capacity: 10 sets maximum. Proximity card capacity: 10 sets maximum. Remote control capacity: 10 sets maximum. U P6. COMPONENTS A. Exterior Assembly B. Cable C. Tailpiece D. Mounting Plate P7. E. 1-1/4" (32mm) Screw (1) F. 2-1/8" (54mm) Mounting Bolt (2) G. Interior Assembly H. 5/16" (7.8mm) Screw (2) I. 13/16" (20mm) Screw (1) J. Decorative Cover K. Adjustable Latch (Square or radius faceplate or drive-in) L. 6/8" (19mm) Wood Screw (4) M. Strike Plate N. Reinforced Strike Plate O. Dust Box P. 3" (76mm) Wood Screw (2) Q. Key (2) R. Drive in Collar (Optional) S. Bottom Plate (Optional) T. Square or Radius Faceplate (Optional) U. Screw post P8. INSTALLATION INSTRUCTIONS: DOOR PREPARATION P9. INSTALLATION INSTRUCTION P10. INSTALLATION INSTRUCTIONS P11. INSTALLATION INSTRUCTION P12. INSTALLATION INSTRUCTIONS P13. INSTALLATION INSTRUCTIONS: LATCH BASKET ADJUSTMENT P14. INSTALLATION INSTRUCTION P15. INSTALLATION INSTRUCTION P16. INSTALLATION INSTRUCTIONS: COMBINE THE EXTERIOR ASSEMBLY WITH LATCH Drill a 5/16(8mm) hole on the door when the screw post is installed. Move the tailpiece horizontally into the latch Place the cable underneath the latch P17. INSTALLATION INSTRUCTION: COMBINE THE MOUNTING PLATE WITH THE EXTERIOR ASSEMBLY The bulged part of mounting plate must face toward the door Slide cable through the notch of mounting plate P18. INSTALLATION INSTRUCTION Make sure the mounting plate is parallel with the edge of the door Fasten the mounting plate with 2-1/8" (54mm) screws*2 and 1-1/4" (32mm) screw*1 Note: Screw (E) is an optional screw. We recommend using screw (E) for the stability of the lockset. P19. INSTALLATION INSTRUCTIONS: REMOVE THE DECORATIVE COVER 1. Hold on the lip of the 2. Put the thumbs on the 3. Remove the decorative cover decorative cover thumbturn by pushing the thumbturn. P20. INSTALLATION INSTRUCTIONS: CONNECTING THE CABLE Connect the cable into the connector port. The metal connector side should face outside. Cable Connector port Note: The red portion of the cable is aligned with the red portion of the connector port. P21. INSTALLATION INSTRUCTIONS The cable must be arranged as shown in the diagram. P22. INSTALLATION INSTRUCTIONS: INSTALL THE INTERIOR ASSEMBLY Insert 5/16" (7.8mm) screws "H"
and tighten Tighten three screws as shown below Insert 13/16" (20mm) screw "I" and tighten. P23. INSTALLATION INSTRUCTIONS: AUTOMATIC - BOLT DIRECTION DETERMINATION Steps:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press press direction set. button. The Red LED will light up for 10 seconds. The lockset will have the bolt button. Enter [00] and Note: We recommend to do bolt direction determination first once the lockset is installed on the door. P24. INSTALLATION INSTRUCTIONS: RE-INSTALL THE DECORATIVE COVER We recommend re-installing the decorative cover after completing setup mode in page 18 to page 30. Re-install the decorative cover If you want to remove the decorative cover, please hold the bottom of the decorative cover and pull it toward yourself. P25. SETUP MODE HOW TO CHANGE PROGRAMMING CODE Important:
Steps as following:
1. The pre-set programming code is 1-2-3-4-5-6. Please change the programming code before operating the lockset. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button
. Enter [10] and press button
. Enter new programming code (six digits) and press button
. 3. The Red LED will light up for 10 seconds. The lockset will have the new programming code set. Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. If you enter new programming code in 10 seconds after accessing setup mode, the last programming code will be stored in the lockset. P26. SETUP MODE HOW TO ADD AN USER CODE Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. 3. Enter 123456 (or current programming code) and then press button button The Red LED will light up for 10 seconds. The lockset will have the new user code set. Enter new user code (four to six digits) and press button
. Enter [20] and press
(If a number of user codes are to be added at the same time, enter new user code and press indicator light timing out 10 seconds after the last press of a keypad button.) Note:
prior to the 1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. P27. SETUP MODE HOW TO ADD A PROXIMITY CARD (only available for Proximity Card Electronic Deadbolt) Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button
. Enter [20] and press button
. Put card to contact with the inductive zone. 3. The Red LED will light up for 10 seconds. The lockset will have the new card set.
(If a number of proximity cards are to be added at the same time, use new card to contact with the inductive zone prior to the indicator light timing out 10 seconds after the last press of a keypad button.) Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. Please use or purchase proximity cards compatible with standard Mifare -13.56 MHz if you want to have more than one proximity card. 3. Proximity card capacity: 10 sets maximum. P28. SETUP MODE HOW TO ADD A REMOTE CONTROL (only available for Remote Control Electronic Deadbolt) Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. Enter 123456 (or current programming code) and then press button
. Press any button on the remote control and press button button
. Enter [20] and press
. 3. The Red LED will light up for 10 seconds. The lockset will have the new remote control set.
(If a number of remote controls are to be added at the same time, press any button of the every remote control consecutively and press button a keypad button.) Note:
finally prior to the indicator light timing out 10 seconds after the last press of 1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. Please purchase a remote control (produced by our company) from an authorized retailer if you want to have more than one remote control. 3. Remote control capacity: 10 sets maximum. P29. SETUP MODE HOW TO ADD A SINGLE-USE USER CODE/ REMOTE CONTROL (single-use remote control only available for Remote Control Electronic Deadbolt) Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. Enter 123456 (or current programming code) and then press button Please turn on auto-lock mode according to page 38 before following the below steps to enable single-use user code/ remote control. 2. 3. single-use Follow the below steps. Enter [21]
Press button User code Remote control Note:
Enter user codes (4 to 6 digits) Press button Press any button on the remote control Press button User codes could be stored to 5 sets Remote controls could be stored to 5 sets 1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. Single-use user code capacity: 5 sets maximum. 3. Single-use remote control capacity: 5 sets maximum. 4. Single-entry user code/single-entry user remote control is only allowed to work once and will become invalid after one use (entry). 5. Do not use your multiple-entry user code/ multiple-entry remote control to facilitate single-entry operation, or your user code and remote control will become invalid after only one use (entry). P30. SETUP MODE HOW TO DELETE AN INDIVIDUAL EXISTING USER CODE Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. 3. Enter 123456 (or a current programming code) and then press button button The Red LED will light up for 10 seconds. The lockset will delete the existing user code that you do not want. Enter existing user code (that you wish to delete) and press button
. Enter [30] and press
(If a number of user codes are to be deleted at the same time, enter each user code to be deleted and press prior to the indicator light timing out 10 seconds after the last press of a keypad button.) Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. P31. SETUP MODE HOW TO DELETE AN INDIVIDUAL EXISTING REMOTE CONTROL (only available for Remote Control Electronic Deadbolt) Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. 3. Enter 123456 (or current programming code) and then press button button button The Red LED will light up for 10 seconds. The lockset will delete the existing remote control that you do not want. Press any button on the remote control (that you wish to delete) and press
. Enter [30] and press
(If a number of remote controls are to be deleted at the same time, press any button of the every remote control consecutively and press button of a keypad button.) Note:
finally prior to the indicator light timing out 10 seconds after the last press 1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. If any remote control is lost, for your safety, please delete all remote controls and re-add current remote controls excluding the lost one. P32. SETUP MODE HOW TO DELETE AN INDIVIDUAL EXISTING PROXIMITY CARD (only available for Proximity Card Electronic Deadbolt) Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. 3. Enter 123456 (or current programming code) and then press button button The Red LED will light up for 10 seconds. The lockset will delete the existing card that you do not want. Put the card that you wish to delete to contact with the inductive zone. Enter [30] and press
(If a number of cards are to be deleted at the same time, use every card to contact with the inductive consecutively prior to the indicator light timing out 10 seconds after the last press of a keypad button.) Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. If any card is lost, for your safety, please delete all cards and re-add current cards excluding the lost one. P33. SETUP MODE HOW TO DELETE ALL EXISTING USER CODES AT ONCE Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. Enter 123456 (or current programming code) and then press button button The Red LED will light up for 10 seconds. The lockset will delete all existing user codes. Enter [40] and press
. 2. 3. Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. P34. SETUP MODE HOW TO DELETE ALL EXISTING PROXIMITY CARDS/ REMOTE CONTROLS AT ONCE
(only available for Proximity Card Electronic Deadbolt/ Remote Control Electronic Deadbolt) Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. 3. Enter 123456 (or current programming code) and then press button button The Red LED will light up for 10 seconds. The lockset will delete all existing cards and remote controls. Enter [41] and press
. Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. If any card/ remote control is lost, for your safety, please delete all cards/ remote controls and re-add current cards/ remote controls excluding the lost one. P35. SETUP MODE HOW TO DISABLE ALL EXISTING USER CODES (VACATION MODE) Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. 3. 4. Enter 123456 (or current programming code) and then press button button Enter [0] and press button on vacation mode. The Red LED will light up for 10 seconds. The lockset will turn
. Enter [50] and press Enter [1] and press button off vacation mode. (Default vacation mode is off)
. The Red LED will light up for 10 seconds. The lockset will turn Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. Vacation mode is used to disable all user codes at the keypad. If a valid user code is entered while the lock is in vacation mode, the lock will not unlock. If you will be away from your home for a period of, it is a good idea to use vacation mode to prevent repeated access attempts. P36. SETUP MODE HOW TO DISABLE BUTTON SOUND (MUTE MODE) Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. 3. 4. Enter 123456 (or current programming code) and then press button button Enter [0] and press button on mute mode. again. The Red LED will light up for 10 seconds. The lockset will turn
. Enter [60] and press Enter [1] and press button off mute mode. (Default mute mode is off.)
. The Red LED will light up for 10 seconds. The lockset will turn Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. P37. SETUP MODE HOW TO SETUP AUTO-LOCK TIME DELAY Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. Enter 123456 (or current programming code) and then press button button
. Enter the seconds for delay time of auto-locking (10 to 90) and press button The Red LED will light up for 10 seconds. The lockset will setup auto-lock time delay. Enter [70] and press
. 2. 3. Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. The lockset will flash and beep three times if the seconds for delay time of auto-locking is not within 10 to 90 seconds. 3. Default auto-lock time delay is 10 seconds. P38. SETUP MODE HOW TO ENABLE AUTO-LOCK MODE Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. 3. 4. Enter 123456 (or current programming code) and then press button button Enter [0] and press button on auto-lock mode. The Red LED will light up for 10 seconds. The lockset will turn
. Enter [80] and press Enter [1] and press button off auto-lock mode. (Default auto-lock mode is off)
. The Red LED will light up for 10 seconds. The lockset will turn Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. The lockset will auto-lock in 10 seconds (default value) without flashing and beeping after unlocking if you turn on auto-lock mode. 3. The lockset can still be locked by pressing button auto-lock mode. manually even if you turn on P39. SETUP MODE HOW TO ENABLE DOUBLE AUTHORIZATION MODE (only available for Proximity Card Electronic Deadbolt/ Remote Control Electronic Deadbolt) Steps as following:
1. Press and hold [SET] button for over 2 seconds. The Red LED will light up and beep twice. You are now under setup mode. 2. 3. Enter 123456 (or current programming code) and then press button button Enter [0] and press button on double authorization mode. The Red LED will light up for 10 seconds. The lockset will turn
. Enter [99] and press
(When double authorization mode is turned on, both user code and card, or, both user code and remote control must be authenticated to unlock the lockset.) 4. The Red LED will light up for 10 seconds. The lockset will turn Enter [1] and press button off double authorization mode. (Default double authorization mode is off.) Note:
1. The lockset will go back to the standby status if no button is pressed in 10 seconds after accessing setup mode. 2. Please make sure that both user code and card, or both user code and remote control, are stored in the lockset before you turn on double authorization mode. P40. SETUP MODE HOW TO RESTORE FACTORY SETTING Steps as following:
1. 2. Remove one battery from the battery pack. Press [SET] button and put the battery back simultaneously. The Green LED will light up and beep twice. All functions will be restored back to factory setting. Note:
1. All existing user codes and current programming code will be deleted. 2. Lock will be restored to pre-set programming code of 1-2-3-4-5-6. 3. Please change the programming code and add a new user code immediately before operating the lockset. P41. SETUP MODE HOW TO REPLACE BATTERIES OF REMOTE CONTROL Steps as following:
1. 2. 3. Loose two screws before opening the bottom shell. Take the PCB out. Push the battery out by inserting the tool into the crack between the PCB and the electrode terminal. Push into the new battery. Replace the PCB. Place the bottom shell back and tighten the screws. Bottom shell Screws PCB Battery case CR2032 Battery
(The carving side should face up and the connecting point should face down) Front shell 4. 5. 6. P42. OPERATION MODE HOW TO LOCK manually Keypad: Press button Remote control: Press lock button to lock the door as shown. (Only available for Remote Control Electronic Deadbolt) to lock the door. HOW TO LOCK automatically 1. Auto-lock mode should be turned on and auto-lock time delay should be also set up. 2. The lockset will be auto-locked in few seconds (default 10 seconds or the time you entered) after unlocking by using codes, card, or remote control. P43. OPERATION MODE HOW TO UNLOCK 1. Enter a valid code, put card to contact with the inductive zone, or press unlock button on the remote control to unlock the lockset. 2. With double authorization mode is turned on, both user code and card, or both user code and remote control, must be authenticated to unlock the lockset. Note:
1. If you cannot unlock the lockset by using card, especially the lockset is mounted outside or under the sun, please wakeup the lockset by pressing button unlock the lockset by using card. on the keypad first, then 2. When you enter codes, the keypad backlight will also be activated automatically under low-light environment. 3. Please press button to clear previous codes and re-enter codes if the previous codes are incorrect. 4. If you do not press button and you have to wait until the red LED lights off, then the lockset is allowed to re-enter codes. to clear previous incorrect codes, the red LED will light up P44. OPERATION MODE SAFE MODE 1. 2. Wrong attempts will not be counted when you press button The keypad will be automatically deactivated for 1 minute after 4 wrong attempts. to clear previous incorrect codes before the red LED lights up. The deadbolt can be locked or unlocked by a valid traditional key under security. 3. P45. TROUBLESHOOTING GUIDELINE QUESTIONS The lockset did not operate correctly after installation. Feel a bump while turning of the motor. Feel a bump while turning the thumbturn or the key. Keypad is not response at all. Programming code cannot be changed. I cannot delete all user codes. I cannot add a new user code. ANSWERS 1. Check center of strike hole for alignment with latch hole on the door to ensure free movement for the deadbolt. 2. Make sure the tailpiece is properly inserted
(in the horizontal position) in the latch. 3. Do [AUTOMATIC -BOLT DIRECTION DETERMINATION]. 1. Please rotate the thumbturn back and forth a few times. 1. Please execute lock & unlock function to allow the motor for repositioning again. 1. Check to see if the batteries are well-installed. 2. Check to see if the Yellow LED light is flashing or not. It means "low battery" when the light keeps flashing. 3. Make sure the cable is well-connected to the port. 1. Please complete the "HOW TO CHANGE PROGRAMMING CODE" process by inputting codes within 10 seconds. 2. Please make sure you have entered the new programming code twice correctly or go back to the factory setting and reset the programming code again. 1. Make sure all code inputting processes should be completed within 10 seconds. 2. Make sure you have entered the correct programming code. button should be held over 3 3. seconds. 1. Make sure all code inputting processes should be completed within 10 seconds. 2. Make sure you have entered the correct programming code. The lockset is not able to unlock by the keypad I am unable to reset the lockset. Red LED light is still on after setting is completed.
"Auto lock" is malfunction. Yellow LED light keeps flashing. What should I do if I input the wrong code?
How to operate this lock under a dark situation?
Card or remote control is lost. Need more remote controls. 3. The new user code will not be accepted if 10 sets of user codes are already stored in the memory. 1. Make sure you have entered the correct user code. 2. Check to see if the Yellow LED light is flashing or not. It means "low battery" if the light keeps flashing. 3. Please make sure the position of strike plate is installed correctly if you see the latch is jammed. 1. Please refer to "HOW TO RESTORE FACTORY SETTING section and make sure all steps are followed correctly. 2. Check to see if the Yellow LED light is flashing or not. It means "low battery" if the light keeps flashing. 1. Please make sure if [SET] button is jammed. 2. Please re-install the batteries. 1. Please make sure turn on auto-lock mode. 2. Check to see if the Yellow LED light is flashing or not. It means "low battery" if the light keeps flashing. The battery is getting low, please reinstall all new batteries for best performance (AA size Alkaline batteries are only allowed). 1. Press button once and continue to input code according to regular procedures. 1. Press any button on the keypad to initiate LED backlight. 1. For your safety, please delete all cards/
remote controls and re-add current cards/
remote controls excluding the lost one. 1. Please purchase the remote control
(produced by our company) from an authorized retailer. Other remote controls Need more proximity cards. What should I do if the lockset cannot be unlocked by using card?
maybe not compatible with this lockset. 1. Proximity card we offer is the latest Radio Frequency Identification (RFID) technology, compatible with standard Mifare -13.56 MHz. 2. You can use any card compatible with standard Mifare -13.56 MHz or purchase new cards from an authorized retailer. 1. Make sure this card is stored in the lockset. 2. Please press button first then use card to unlock. 3. Please put card to contact with the inductive zone to unlock. If the lock appears to be damaged or does not function properly, please contact your local provider for more help. P49. DECLARATIONS AND SAFETY STATEMENTS Federal Communications Commission Statement This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC Regulations This Class B digital apparatus complies with Canadian ICES-003. This device complies with Industry Canada licence-exempt RSS-210 standard. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. P50. DATA RECORDS
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2012-07-12 | 2406 ~ 2406 | DXX - Part 15 Low Power Communication Device Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2012-07-12
|
||||
1 | Applicant's complete, legal business name |
Taiwan Fu Hsing Industrial Co., Ltd.
|
||||
1 | FCC Registration Number (FRN) |
0021762976
|
||||
1 | Physical Address |
No.88, Yucai Rd., Gangshan Dist.
|
||||
1 |
Kaohsiung City,, N/A 820
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
J******@eurofins.de
|
||||
1 | TCB Scope |
A2: Low Power Transmitters (except Spread Spectrum) and radar detectors operating above 1 GHz
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
O3I
|
||||
1 | Equipment Product Code |
A05
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
J****** H******
|
||||
1 | Title |
Director
|
||||
1 | Telephone Number |
+886 ******** Extension:
|
||||
1 | Fax Number |
+886 ********
|
||||
1 |
a******@fuhsing.com.tw
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Worldwide Testing Services (Taiwan) Co., Ltd.
|
||||
1 | Name |
T****** C****
|
||||
1 | Physical Address |
6F., No. 58, Lane 188, Ruey Kuand Rd.
|
||||
1 |
Taipei, 114
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
+886-******** Extension:
|
||||
1 | Fax Number |
+886-********
|
||||
1 |
j******@wts-lab.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DXX - Part 15 Low Power Communication Device Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Remote Control Electronic Deadbolt | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Worldwide Testing Services (Taiwan) Co. Ltd.
|
||||
1 | Name |
C**** T****
|
||||
1 | Telephone Number |
88626******** Extension:
|
||||
1 | Fax Number |
88626********
|
||||
1 |
j******@wts-lab.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2406.00000000 | 2406.00000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC