FCC ID: RYYEYSNCN Bluetooth low energy/ ANT/ 802.15.4 Module

EYSNCN 24-Dec.2019 Ver.0.9 TAIYO YUDEN CO., LTD. Bluetooth low energy/ANT/802.15.4 Module User manual

(for EYSNCN) FCC ID: RYYEYSNCN IC Number: 4389B-EYSNCN TAIYO YUDEN CO., LTD. 1/3 EYSNCN 24-Dec.2019 Ver.0.9 TAIYO YUDEN CO., LTD. Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification

(installation procedure). The following information must be indicated on the host device of this module;

1) Japan Regulatory Information a) This module is approved with the specic antenna on this module. b) Please ensure that your product can bear a label with the following information. If the product is so small that it is not practicable to place the label, please place it in the instruction manual and package. This product installs a radio system which has been approved as a radio station in a low power data communication system based on the Radio Law. EYSNCN : -

2) Canada Regulatory Information a) This device complies with Industry Canadas applicable licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. b) This product is certified as type of the portable device with Industry Canada Rules. To maintain compliance with RF Exposure requirement,please use within specification of this product. Ce produit est certifi comme type de l'appareil portable avec Industrie Rgles de Canada. Pour maintenir l'acquiescement avec exigence Exposition de RF, veuillez utiliser dans spcification de ce produit.

- IC: 4389B-EYSNCN c) Please notify certified ID by either one of the following method on your product.

-Contains IC : 4389B-EYSNCN Specifiez ID certifie dans votre produit par une de mthode suivante.

-Contains IC : 4389B-EYSNCN TAIYO YUDEN CO., LTD. 2/3 EYSNCN 24-Dec.2019 Ver.0.9 TAIYO YUDEN CO., LTD. 3) FCC Regulatory Information a) This device complies with part 15 of the FCC Rules.

-Part 15 Subpart C b) Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. c) Please notify certified ID by either one of the following method on your product.

-Contains Transmitter Module FCC ID: RYYEYSNCN

-Contains FCC ID: RYYEYSNCN d) CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the uses authority to operate the equipment. e) The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. f) This product is certified as type of the portable device with FCC Rules. To maintain compliance with RF Exposure requirement, please use within specification of this product. g) The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. h) This module can change the output power depending on the circumstances by the application software which is developed by module installer. Any end user cannot change the output power. The software is developed by Taiyo Yuden, and the output power cannot be changed to higher than granted power. 4) CE Regulatory Information a) When your end product installs this module, it is required to proceed additional certification processes before placing on the market in EU member states to make your products fully comply with relative EU standards. b) TAIYO YUDEN can provide you the test reports of conducted measurement portion for the radio module. You can utilize the test reports for the certification processes of your end product as it requires radio testing. TAIYO YUDEN CO., LTD. 3/3

Control No. Title APPROVED CHECKED DRAWN DESIGNED HD-AD-

OutlineAppearance 11 Description of laser Marking 8) unit:mm 3) 2) 1) TAIYO YUDEN Model:EYSNCN User-Code LOT NO. XXX-XXXXXX R FCC ID:RYYEYSNCN IC:4389B-EYSNCN 7) 4) 6) 5) 1) Model (upper 6 digits)

: EYSNCN 2) User-Code

3) Manufacturer 4) Japan ID

: TAIYO YUDEN

: XXX-XXXXXX 5) ISED number

: 4389B-EYSNCN 6) FCC ID

: RYYEYSNCN 7) Product Lot number

: Four digits (Refer to [Instruction for Lot Number]) 8) Japan logo mark Specified logo mark TAIYO YUDEN CO.,LTD.

Confidentiality Request Letter Confidentiality Request regarding application for certification of FCC ID: RYYEYSNCN and IC: 4389B-EYSNCN Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, and IC RSP-100, Section 10, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type (Long Term) Block Diagram, Schematics, Operational Description Exhibit Type (Short Term) Photos External Photos Internal Test setup photos User Manual Time of confidentiality: 180 days The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice we also request temporary confidential treatment of information accompanying this application as outlined above. Sincerely, Hideki Kato Deputy General Manager, Business Planning Department, Integrated Module Business Division Taiyo Yuden Co., Ltd.

Applicant/Grantee FCC ID:

TAIYO YUDEN CO., LTD. RYYEYSNCN Section 15.212 Modular Transmitters /

X Request for Modular Approval Request for Limited Modular Approval Requirements Device Conditions Comply (Y/N) Single Modular Approval Requirements The radio elements must have the radio frequency circuitry must be shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly. The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS standard under conditions of excessive data rates or over-modulation. The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. Requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module. The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The Equipment certification submission shall contain a detailed description of the configuration of all antennas that will be used with the module. The module shall be tested for compliance with the applicable standard in a stand-

alone configuration, i.e. the module must not be inside another device during testing. The module has its own RF shielding. Shield Can is employed on the board structure, please see exhibition External Photo, the emission measurement was conducted without further shielding added. All modulation and data input(s) are buffered. The EUT has buffered data inputs, it is integrated on the RF chip Output power is controlled by the RF Chip and de-coupled from supply voltage variations. Frequencies are determined by Crystal The antenna is part of the module The modular transmitter was tested in a stand-alone configuration via a SPI Interface. The module shall comply with the Category I equipment labelling requirements. In the exhibition OEM manual, there are Instructions given to the OEM on how to label the end product. 1 2 3 4 5 6 Y Y Y Y Y Y The modular transmitter complies with all specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer will provide adequate instructions along with the module to explain any such requirements. A copy of these instructions is included in this application for equipment authorization:

Address compliance with the Commission's RF exposure limits in Sections 1.1310 and 2.1093. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF exposure compliance in accordance with Section 15.247(b)(4). 7 8a Instructions in User Manual Please refer the Maximum Permissible Exposure Information. Y Y A single modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured. Signature Name/Title: Hideki Kato /Deputy General Manager Company Name: TAIYO YUDEN CO., LTD. Date: 29 Jan. 2020