User Guide Targus Wireless Comfort Laser Mouse Introduction Thank you for your purchase of the Targus Wireless Comfort Laser Mouse. The accompanying micro USB receiver is small enough to leave plugged into your computer or simply store it inside the mouse when travelling. This is a plug-n-play device so no additional software is required. The advance scroll wheel feature program can be downloaded from the Targus web-site. Contents
System Requirements Hardware
Operating System
2000
XP
7
X 10.4 or later 2 Targus Wireless Comfort Laser Mouse Installing the Batteries 1. Remove the battery cover from the top of the mouse by using the notch on the back. Carefully lift the cover up as shown in the diagram. 2. Remove the battery safety clip by squeezing the center of the clip and sliding it back, towards the rear of the mouse. Lift up and rotate the clip out of the way. NOTE: THE BATTERY SAFETY CLIP WILL NEED TO BE IN THE SECURE, LOCKED POSI-
TION BEFORE THE BATTERY COVER CAN BE PUT BACK IN PLACE. 3 Targus Wireless Comfort Laser Mouse 3. Remove the micro USB receiver stored inside the center compartment . Micro USB receiver 4. Insert the two AA batteries, making sure that the positive (+) and negative (-) ends of each battery match the polarity indicators inside the battery compartment. 4 Targus Wireless Comfort Laser Mouse 5. Replace the battery safety clip by sliding it forward until it clicks into place and then replace the battery cover. 5 Targus Wireless Comfort Laser Mouse Establishing the Connection
(A) Plug the USB receiver into an available USB port on your computer.
(B) Turn on the mouse pressing the power button, located on the bottom of the mouse, for 3 seconds and then release. Power Button This mouse is a plug-n-play device. It will automatically operate when the USB receiver is connected to the computer. 6 Targus Wireless Comfort Laser Mouse Power On:
Press and hold the power button for 3 seconds and then release. The battery life indicator will briey light up showing the current power level of the batteries. Power Off:
Press and hold the power button for 3 seconds and then release. The battery life indicator will briey light up and then fade out. Battery Check:
After the mouse is turned on, quickly press and release the power button. The battery life indicator will light up showing the current power level of the batteries. Power Saving mode:
cally enter power saving mode to conserve power and increase battery life. Click on any mouse button to resume the normal operation. The mouse may take a few seconds to re-connect with your computer. 7 Targus Wireless Comfort Laser Mouse Battery Life Indicator 3 LEDs lit 2 LEDs lit 1 LED lit Full power Half power Low power NOTE: WHEN THE FIRST LIGHT IS BLINKING, PLEASE REPLACE THE BATTERIES Power Management
when youre not using it. 8 Targus Wireless Comfort Laser Mouse Programming Your Mouse
To access the advanced scroll wheel features you will need to download and install the software driver. This can be downloaded from the following location:
www.targus.com to download and install the driver.
desired setting for the scroll-wheel button. Close the driver software application and youre ready to go. Activate your selected feature by pressing down on the scroll wheel. 9 Targus Wireless Comfort Laser Mouse Technical Support For technical questions, please visit:
US Australia New Zealand Internet: www.targus.com/support.asp Internet: www.targus.com/au Email: infoaust@targus.com Telephone: 1800-641-645 Telephone: 0800-633-222 Product Registration Targus recommends that you register your Targus accessory shortly after purchasing it. Go to:
http://www.targus.com/registration.asp You will need to provide your full name, email address, country of residence and product information. Warranty Targus warrants this product to be free from defects in materials and workmanship for one year. If your Targus accessory is found to be defective within that time, we will promptly repair or replace it. This warranty does not cover accidental damage, wear and tear, or consequential or incidental loss. Under no conditions is Targus liable for loss of, or damage to devices; nor loss of, or damage to, programs, records, or data;
nor any consequential or incidental damages, even if Targus has been informed of their possibility. This warranty does not affect your statutory rights. Regulatory Compliance
following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 10 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of FCC RF Rules. Operation is subject to the following two conditions:
1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. Canada Statement This Device complies with RSS-210 of the IC Rules, Operation is subject to the following two conditions:
(1). This device may not cause interference and
(2). This device must accept any interference received,, including interference that may cause undesired operation. Declaration of Conformity Hereby, Targus, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Targus Wireless Comfort Laser Mouse CAUTION
12 S U 1 5 W M A
A 1 0 0
9 8 6 1
0 1 4 1 YEAR LIMITED WARRANTY: We pride ourselves on the quality of our products. For complete warranty details and a list of our worldwide ofces, please visit www.targus.com. Features and specications are sub-
ject to change without notice. All trademarks and reg-
istered trademarks are the property of their respective owners. All rights reserved. 2009 Manufactured or imported by Targus Group International, Inc. (for U.S. sales: 1211 North Miller Street, Anaheim, CA 92806 USA) whose Australian sales representative is Targus Australia Pty. Ltd., 117-119 Bowden Street, Meadow-
bank, NSW 2114 Australia N2953