PRODUCT SPECIFICATION TITLE Full LTE SMT Antenna TABLE OF CONTENTS 1.0 SCOPE 2.0 PRODUCT DESCRIPTION 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS 4.0 RATINGS 5.0 PERFORMANCE 6.0 TEST GROUPINGS 7.0 RECOMMENDED REFLOW CONDITION 8.0 PACKING REVISION: ECR/ECN INFORMATION: TITLE:
A EC No: 103559 DATE: 2016/02/22 Full LTE SMT Antenna SHEET No. 1 of 5 DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001 Benson Liu 2016-02-22 Chris Zhong 2016-02-22 Welson Tan2016-02-22 d TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION Full LTE SMT Antenna 1.0 SCOPE This Product Specification covers the mechanical, electrical and environmental performances requirements and test methods for Full LTE SMT antenna. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER Product name: Full LTE SMT Antenna 146200-0001 2.2 Design and Construction Antenna shall be of the design, construction and physical dimensions specified on the applicable sales drawing. 2.3 Materials a) Ceramic: Refer to respective Molex sales or engineering drawings b) Plating:
Refer to respective Molex sales or engineering drawings 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS See drawings and other sections of this specification for the relevant reference documents. In cases where the specification differs from the drawings, the drawings take precedence. 4.0 RATINGS 4.1 RF POWER 2 WATTS 4.2 TEMPERATURE Operating: - 30C to + 85C Storage : - 40C to + 95C 4.3 HUMIDITY Operating :-30C to+85C
-30C to+50C, 85%RH or less
+50C to+85C, 60%RH or less Storage : -40C to+95C
-40C to+50C, 85%RH or less
+50C to+95C, 60%RH or less REVISION: ECR/ECN INFORMATION: TITLE:
A EC No: 103559 DATE: 2016/02/22 Full LTE SMT Antenna SHEET No. 2 of 5 DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001 Benson Liu 2016-02-22 Chris Zhong 2016-02-22 Welson Tan2016-02-22 d TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 5.0 PERFORMANCE 5.1 ELECTRICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION Measure antenna on REQUIREMENT 5.1.1 Frequency Range recommended PCB through VNA 698-960MHz 1.7-2.7GHz E5071C Measure antenna on 5.1.2 Return Loss recommended PCB through VNA
< -5 dB
< -5 dB E5071C Measure antenna on 5.1.3 Peak Gain recommended PCB through OTA 1.1dBi 4.5dBi 5.1.4 Avg. Total Efficiency chamber Measure antenna on recommended PCB through OTA 60%
70%
chamber Measure antenna on 5.1.5 Polarization recommended PCB through OTA Linear Linear chamber Measure antenna on 5.1.6 Input Impedance recommended PCB through VNA 50 Ohms 50 Ohms 5.2 MECHANICAL REQUIREMENTS E5071C ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.2.1 Ag thickness measure Use X-ray measure the thickness of Ag Ag thickness spec: 8-10um. 5.2.2 Cross cut Test Testing is performed in accordance with Cross cut adhesion test ASTM D-3359-93 Acceptance criteria > 2B as acceptance, <35% peeling off. 5.3 RELIABILITY REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.3.1 Peeling Force Apply six axial peeling force on parts soldered on the PCB at the speed rate of 253 mm/minute 8 N Min REVISION: ECR/ECN INFORMATION: TITLE:
A EC No: 103559 DATE: 2016/02/22 Full LTE SMT Antenna SHEET No. 3 of 5 DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001 Benson Liu 2016-02-22 Chris Zhong 2016-02-22 Welson Tan2016-02-22 d TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 5.4 ENVIRONMENTAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.4.1 Humidity Test 5.4.2 Temperature cycling test 5.4.3 High Temperature 5.4.4 Salt mist test 1.Test condition:
The device under test is kept for 12 hours in an environment with a temperature of 55 degrees and a relating humidity of 95%. Thereafter for 12 Hours in an environment with a temperature of 25 degrees and a relative humidity of 95%. The cycle is repeated until a total of 6 cycles have been completed. Hereafter the conditions are stabilized at room temperature. 1.Test condition:
The device under test at -40 125 by 72 cycles, Dwell of 30 min, transition time between Dwell 15 sec (~ 61 min /
cycle ) and each item should be measured after exposing them in normal temperature and humidity for 24 h. Test condition:
1) Temperature:125, time:1008hours 2) There is no substantial obstruction to air flow across and around the samples, and the samples are not touching each other 1.Test condition:
The device under test is exposed to a spray of a 5% (by volume) resolution of Nacl in water for 2 hours. Thereafter the device under test is left for 1 week in room temperature at a relative humidity of 95%. The cycle is repeated until a total of 2 cycles have been completed. Here after the conditions are stabilized at room temperature. 1) Parts should meet RF spec before and after test. 2 No cosmetic problem 1) Parts should meet RF spec before and after test. 2 No cosmetic problem 1) Parts should meet RF spec before and after test. No cosmetic problem 2) 1) Parts should meet RF spec before and after test. 2) No visible corrosion. Discoloration accept. The meaning of text No mechanical damage in the table above is:
a. no soldering problem b. no adhesion problem of glue c. no peel off of plating REVISION: ECR/ECN INFORMATION: TITLE:
A EC No: 103559 DATE: 2016/02/22 Full LTE SMT Antenna SHEET No. 4 of 5 DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001 Benson Liu 2016-02-22 Chris Zhong 2016-02-22 Welson Tan2016-02-22 d TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 6.0 TEST GROUPINGS Note: All test specimens (except group 5) shall pass the reflow process for 3 times. Description Group1 Group2 Group3 Group4 Group5 Group6 Group7 Test Item 5.2.1 5.2.2 5.3.1 Ag thickness X Cross cut Peeling Force 5.4.1 Humidity Test 5.4.2 Temperature cycling test 5.4.3 High Temperature 5.4.4 Salt mist test X X X Sample Quantity 5 5 5 5 7.0 RECOMMENDED REFLOW CONDITION X 5 X 5 X 5 8.0 PACKAGING Refer to the Molex related packaging drawings. REVISION: ECR/ECN INFORMATION: TITLE:
A EC No: 103559 DATE: 2016/02/22 Full LTE SMT Antenna SHEET No. 5 of 5 DOCUMENT NUMBER:
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
PS-146200-001 Benson Liu 2016-02-22 Chris Zhong 2016-02-22 Welson Tan2016-02-22 d TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC