FCC ID: 2ACCJH089 LTE / UMTS / GSM mobile phone

Safety and Precautions www.sar-tick.com This product meets applicable national SAR limits of 1.6 W/kg. The specific maximum SAR values can be found in the Radio waves section. When carrying the product or using it while worn on your body, either use an approved accessory such as a holster or otherwise maintain a distance of 10 mm from the body to ensure compliance with RF exposure requirements. Note that the product may be transmitting even if you are not making a phone call. PROTECT YOUR HEARING To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise caution when holding your phone near your ear while the loudspeaker is in use. English - CQF2B03ALAAA Printed in China Safety and use We recommend that you read this chapter carefully before using your phone. The manufacturer disclaims any liability for damage, which may result as a consequence of improper use or use contrary to the instructions contained herein. TRAFFIC SAFETY:

Given that studies show that using a phone while driving a vehicle constitutes a real risk, even when the hands-free kit is used (car kit, headset...), drivers are requested to refrain from using their phone when the vehicle is not parked. Check the laws and regulations on the use of wireless phones and their accessories in the areas where you drive. Always obey them. The use of these devices may be prohibited or restricted in certain areas. CONDITIONS OF USE:

You are advised to switch off the phone from time to time to optimize its performance;

Remember to abide by local authority rules of mobile phone use on aircrafts;

If your phone is a unibody device, where the back cover and battery are not removable, disassembling the phone will void your warranty. Disassembling the phone can cause bodily injury if the battery is punctured;

Always handle your phone with care and keep it in a clean and dust-free place;

Do not allow your phone to be exposed to adverse weather or environmental conditions, such as moisture, humidity, rain, infiltration of liquids, dust, sea air, etc. The manufacturers recommended operating temperature range is -10C (14F) to +45C (131F). At over 45C (131F), the legibility of the phones display may be temporarily impaired;

Do not open, dismantle, or attempt to repair your phone yourself;

Do not drop, throw, or bend your phone;

1 Use only batteries, battery chargers, and accessories which are recommended by TCL Communication Ltd. and its affiliates and are compatible with your phone model. TCL Communication Ltd. and its affiliates disclaim any liability for damage caused by the use of other chargers or batteries;

Your phone should not be disposed of in a municipal waste. Please check local regulations for disposal of electronic products;

Remember to make backup copies or keep a written record of all important information stored on your phone;

Some people may suffer epileptic seizures or blackouts when exposed to flashing lights, or when playing video games. These seizures or blackouts may occur even if a person never had a previous seizure or blackout. If you have experienced seizures or blackouts, or if you have a family history of such occurrences, please consult your doctor before playing video games on your phone or enabling a flashing-lights feature on your phone;

Parents should monitor their childrens use of video games or other features that incorporate flashing lights on the phones. All persons should discontinue use and consult a doctor if any of the following symptoms occur: convulsion, eye or muscle twitching, loss of awareness, orientation, or movements. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. PRIVACY:

Please note that you must respect the laws and regulations in force in your jurisdiction or other jurisdiction(s) where you will use your phone regarding taking photographs and recording sounds with your phone. Pursuant to such laws and regulations, it may be strictly forbidden to take photographs and/or to record the voices of other people or any of their personal attributes, and reproduce or distribute them, as this may be considered to be an invasion of privacy. It is the user's sole responsibility to ensure that prior authorization has been obtained, if necessary, in order to record private or confidential conversations or take a photograph of another person; the manufacturer, the seller or vendor of your phone (including the carrier) disclaim any liability which may result from improper use of the phone. 2 BATTERY:

For a non-unibody device:

Observe the following precautions:

Do not attempt to open the battery (due to the risk of toxic fumes and burns);

Do not puncture, disassemble, or cause a short circuit in the battery;

Do not burn or dispose of a used battery in household garbage or store it at temperatures above 60C (140F). Batteries must be disposed of in accordance with locally applicable environmental regulations. Only use the battery for the purpose for which it was designed. Never use damaged batteries or those not recommended by TCL Communication Ltd. and/or its affiliates. For a non-unibody device with a non-removable battery:

Observe the following precautions:

Do not attempt to eject, replace, or open the battery;

Do not puncture, disassemble, or cause a short circuit in the battery;

Do not burn or dispose of your phone in household garbage or store it at temperature above 60C (140F). Phone and battery must be disposed of in accordance with locally applicable environmental regulations. For a unibody device:

Observe the following precautions:

Do not attempt to open the back cover;

Do not attempt to eject, replace, or open the battery;

3 Do not puncture the back cover of your phone;

Do not burn or dispose of your phone in household rubbish or store it at temperature above 60C (140F);

Phone and battery as a unibody device must be disposed of in accordance with locally applicable environmental regulations. This symbol on your phone, the battery, and the accessories means that these products must be taken to collection points at the end of their life:

Municipal waste disposal centers with specific bins for these types of equipment;

Collection bins at points of sale. They will then be recycled, preventing substances being disposed of in the environment, so that their components can be reused. In European Union countries:

These collection points are accessible free of charge. All products with this sign must be brought to these collection points. In non-European Union jurisdictions:

Items of equipment with this symbol are not to be thrown into ordinary bins if your jurisdiction or your region has suitable recycling and collection facilities; instead they are to be taken to collection points for them to be recycled. In the United States you may learn more about CTIAs Recycling Program at http://www.gowirelessgogreen.org/

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 4 CHARGERS:

Home A.C./ Travel chargers will operate within the temperature range of: 0C (32F) to 40C (104F). The chargers designed for your phone meet the standard for safety of information technology equipment and office equipment use. Due to different applicable electrical specifications, a charger you purchased in one jurisdiction may not work in another jurisdiction. They should be used for this purpose only. Characteristics of power supply (depending on the country):

Travel charger: Input: 100-240V,50/60Hz, 150mA Battery:

Output:5V,550mA Lithium 2000 mAh Radio waves THIS PHONE MEETS THE GOVERNMENTS REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio-frequency (RF) energy. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. These guidelines include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. The exposure standard for phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by public authorities such as the Federal Communications Commission of the US Government (FCC), or by Innovation, Science and Economic Development Canada (ISEDC), is 1.6 W/kg averaged over 1 gram of body tissue. Tests for SAR are conducted using standard operating positions with the phone transmitting at its highest certified power level in all tested frequency bands. 5 This device is complied with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/

oet/ea/fccid after searching on FCC ID : 2ACCJH089 Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output of the phone. Before a phone model is available for sale to the public, compliance with national regulations and standards must be shown. The highest SAR value for 5033A/5033J when tested is 0.99 W/Kg for use at the ear and 1.19 W/Kg for use close to the body. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for RF exposure. For body-worn operation, the phone meets FCC RF exposure guidelines provided that it is used with a non-metallic accessory with the handset at least 10 mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Additional information on SAR can be found on the Cellular Telecommunications & Internet Association (CTIA) Web site: http://www.ctia.org/

The World Health Organization (WHO) considers that present scientific information does not indicate the need for any special precautions for use of phones. If individuals are concerned, they may choose to limit their own or their childrens RF exposure by limiting the length of calls, or using hands-

free devices to keep phones away from the head and body. Additional WHO information about electromagnetic fields and public health are available on the following website: http://www.who.int/peh-emf. 6 Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna;

Increase the separation between the equipment and receiver;

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;

Consult the dealer or an experienced radio/ TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. For the receiver devices associated with the operation of a licensed radio service (e.g. FM broadcast), they bear the following statement:

This phone complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference;

This device must accept any interference received, including interference that may cause undesired operation. Your phone is equipped with a built-in antenna. For optimal operation, you should avoid touching it or degrading it. As mobile devices offer a range of functions, they can be used in positions other than against your ear. In such circumstances the device will be compliant with the guidelines when used with a headset or usb data cable. If you are using another accessory ensure that whatever product is used is free of any metal and that it positions the phone at least 10 mm away from the body. 7 Please note by using the device some of your personal data may be shared with the main device. It is under your own responsibility to protect your own personal data, not to share with it with any unauthorized devices or third party devices connected to yours. For products with Wi-Fi features, only connect to trusted Wi-Fi networks. Also when using your product as a hotspot (where available), use network security. These precautions will help prevent unauthorized access to your device. Your product can store personal information in various locations including a SIM card, memory card, and built-in memory. Be sure to remove or clear all personal information before you recycle, return, or give away your product. Choose your apps and updates carefully, and install from trusted sources only. Some apps can impact your products performance and/or have access to private information including account details, call data, location details and network resources. Note that any data shared with TCL Communication Ltd. is stored in accordance with applicable data protection legislation. For these purposes TCL Communication Ltd. implements and maintains appropriate technical and organizational measures to protect all personal data, for example against unauthorized or unlawful processing and accidental loss or destruction of or damage to such personal data whereby the measures shall provide a level of security that is appropriate having regard to The technical possibilities available;

The costs for implementing the measures;

The risks involved with the processing of the personal data, and;

The sensitivity of the personal data processed. You can access, review, and edit your personal information at any time by logging into your user account, visiting your user profile or by contacting us directly. Should you require us to edit or delete your personal data, we may ask you to provide us with evidence of your identity before we can act on your request. 8 Licenses microSD Logo is a trademark. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by TCL Communication Ltd. and its affiliates is under licence. Other trademarks and trade names are those of their respective owners. Alcatel 5033A/5033J Bluetooth Declaration ID D038401 The Wi-Fi Logo is a certification mark of the Wi-Fi Alliance. Google, the Google logo, Android, the Android logo, Google SearchTM, Google MapsTM, GmailTM, YouTube, Google Play Store, Google LatitudeTM, and HangoutsTM are trademarks of Google Inc. The Android robot is reproduced or modified from work created and shared by Google and used according to terms described in the Creative Commons 3.0 Attribution License (the text will show when you touch Google legal in Settings > About phone > Legal information) (1). You have purchased a product which uses the open source (http://opensource.org/) programs mtd, msdosfs, netfilter/iptables and initrd in object code and other open source programs licensed under the GNU General Public Licence and Apache Licence. We will provide you with a complete copy of the corresponding source codes upon request within a period of three years from the distribution of the product by TCL Communication Ltd. You may download the source codes from http://sourceforge.net/projects/alcatel/files/. The provision of the source code is free of charge from the internet.

(1) May not be available in all countries. 9 General information Website(USA): https://us.alcatelmobile.com Facebook (USA): https://www.facebook.com/alcatelmobileus Twitter (USA): https://twitter.com/alcatelmobileus Instagram (USA): https://www.instagram.com/alcatelmobileus Hotline: In the United States, call 855-368-0829 for technical support. Manufacturer: TCL Communication Ltd. Address: 5/F, Building 22E, 22 Science Park East Avenue, Hong Kong Science Park, Shatin, NT, Hong Kong Electronic labeling path: Touch Settings > Regulatory & safety or press *#07# to find more information about labeling (1), such as FCC ID. On our website, you will find our FAQ (Frequently Asked Questions) section. You can also contact us by email to ask any questions you may have. Your phone is a transceiver that operates on GSM in quad-band (850/900/1800/1900 MHz), UMTS in penta-band (B1/2/4/5/8) or LTE

(B1/2/3/4/5/7/8/12/13/17/28). Protection against theft (2) Your phone is identified by an IMEI (phone serial number) shown on the packaging label and in the phones memory. We recommend that you note the number the first time you use your phone by entering *#06# and keep it in a safe place. It may be requested by the police or your carrier if your phone is stolen. This number allows your phone to be blocked preventing a third person from using it, even with a different SIM card.

(1) This may vary depending on country.

(2) Contact your service provider to check service availability. 10 Disclaimer There may be certain differences between the user manual description and the phones operation, depending on the software release of your phone or specific carrier services. TCL Communication Ltd. shall not be held legally responsible for such differences, if any, nor for their potential consequences, which responsibility shall be borne by the carrier exclusively. Warranty For information on warranty of your device, visit USA website at https://us.alcatelmobile.com/warranty/. Electronic Recycling For more information on Electronic Recycling, please Visit Alcatel Electronic Recycling Program website at (USA) https://us.alcatelmobile.com/

accessibility-compliance/electronic-recycling-program/. Battery Recycling Alcatel partners with Call2Recycle to offer a safe and convenient battery recycling program.For more information on our Battery Recycling Program, please visit the USA website at https://us.alcatelmobile.com/accessibility-compliance/battery-recycling/. 11 Troubleshooting Before contacting the service center, you are advised to follow the instructions below:

To have optimal operation, fully charge the battery. To improve the phones performance, remove unnecessary files or apps on your phone. To update your system software, use the System Updates command in your phones settings. To set your phone to factory default, use the Backup & Reset in the phones settings, All your phone data will be lost permanently. It is strongly advised to fully back up your phone before resetting. My phone can't be switched on When the phone can't be switched on, charge for at least 10 minutes to ensure the minimum battery power needed. Then switch it on again. My phone has not responded for several minutes If your phone doesnt respond, turn off your phone by pressing and holding the Power key until it turns off and then restart it again. If your phone has a removable battery, remove the battery and re-insert it, then restart the phone. My phone turns off by itself When your phone turns off by itself, make sure that the Power key is not accidentally pressed. Check the battery charge level. Check your phones settings for turning off the phone at a certain time. If it still doesn't work, Factory reset the phone via the Backup & reset in the phones Settings. Make sure you have backed up your data. 12 My phone can't charge properly Make sure that you are using the proper charger that comes with the phone. If your phone has a removable battery, make sure that your battery is inserted properly and the battery terminal makes a good contact with the phone. It must be inserted before plugging in the charger. Make sure that your battery is not completely discharged; if the battery power has been discharged for a long time, it may take around 10 minutes to display the battery charging indicator on the screen. Make sure that charging is carried out under normal conditions (0C (32F) to 55C (131F)). When abroad, check that the voltage input is compatible. Check that the charging port is secured or its not damaged. My phone can't connect to a network or "No service" is displayed Try connecting to the network by moving to another physical location. Verify the network coverage with your carrier in your current area. Check with your carrier that your SIM card is valid. Make sure your phones setting is not in airplane mode. If you are away from your carriers network, you may need to enable roaming in the phones settings to connect to other network. Roaming charges may apply. My phone can't connect to the internet Make sure that Cellular Data internet service is available in your wireless service plan. 13 Check your phone's settings. Make sure Cellular Data is enabled or Wi-Fi connected. Make sure that you are in a place with network coverage for cellular data or Wi-Fi internet connection. Try connecting at a later time or another location. Invalid SIM card Make sure that the SIM card has been correctly inserted (see "Inserting or removing the SIM card"). Make sure that the chip on your SIM card is not damaged. Make sure that the service of your SIM card matches the network youre on. My phone can't make outgoing calls Make sure that you have dialed a valid number and have touched Call on your phone. For international calls, check the country and area codes. Make sure that your phone is connected to a network, and the network is not overloaded or unavailable. Check your subscription status with your carrier. Make sure that you have not barred outgoing calls. Make sure that your phone is not in airplane mode. My phone can't receive incoming calls Make sure that your phone is switched on and connected to a network. Check for overloaded or unavailable network. Check your subscription status with your carrier. 14 Make sure that you have not forwarded incoming calls. Make sure that you have not barred certain calls. Make sure that your phone is not in airplane mode. The callers name/number doesn't appear when a call is received Check that you have subscribed Caller ID service with your carrier. Your caller may have concealed his name or number. I can't find my contacts Make sure that your SIM card is not broken. Make sure that your SIM card is inserted properly. Import all contacts stored in SIM card to phone. The sound quality of the calls is poor Adjust the volume during a call by pressing the Volume up/down key. Check the network strength. Move to a location with stronger signal strength. Make sure that the receiver, connector or speaker on your phone is clean. I can't use the features described in the manual Check with your carrier to make sure that your subscription includes this service. Make sure that this feature doesn't require any additional accessory. 15 When I select a number from my contacts, the number can't be dialed Make sure that you have correctly recorded the number in your file. Make sure that you have selected the country code when calling an international number. I can't add a contact Make sure that your SIM card contact list are not full; delete some files or save the files to the phone. My callers can't leave messages on my voicemail Contact your network carrier to check service availability. Set up your voicemail with your carrier, so that your caller can leave a message. I can't access my voicemail Make sure that your carriers voicemail number is correctly entered in "Voicemail number". Try later if the network is busy. I can't send and receive MMS Check your phone memory as it might be full. Contact your network carrier to check service availability and MMS parameters. Verify the server center number or your MMS profile with your carrier. The server center may be swamped. Try again later. Start a new Messaging string. You messaging string may have reached its limit. 16 SIM card PIN locked Contact your network carrier to obtain the PUK (Personal Unblocking Key) code. I can't connect my phone to my computer Install Smart Suite. Check that your USB driver is installed properly. Open the Notification panel to check if the Smart Suite Agent has been activated. Check that you have marked the USB debugging checkbox. Check that your computer meets the requirements for Smart Suite installation. Make sure that youre using the right cable from the box. I can't download new files Make sure that there is sufficient phone storage space for your download. Select the microSD card as the location to store downloaded files. Check your subscription status with your carrier. The phone can't be detected by others via Bluetooth Make sure that Bluetooth is turned on and your phone is visible to other users. Make sure that the two phones are within Bluetooths detection range. The battery drains too fast Make sure that you follow the complete charge time (minimum 200 minutes). 17 After a partial charge, the battery level indicator may not be exact. Wait for at least 10 minutes after removing the charger to obtain an exact indication. Adjust the brightness of screen as appropriate. Extend the email auto-check interval for as long as possible. Update news and weather information on manual demand, or increase their auto-check interval. Exit background-running applications if they are not being used for extended periods of time. Deactivate Bluetooth, Wi-Fi, or GPS when not in use. The phone becomes warm following prolonged calls, game playing, internet surfing or running other complex applications This heating is a normal consequence of the CPU handling excessive data. Ending the above actions will make your phone return to normal temperature. After Factory data reset is performed, I can't use my phone without entering Google account credentials After reset is performed, you must enter the original Google account credentials that were used on this phone. If you dont remember your Google account credentials, complete Google account recovery procedures. If you still cannot access your phone, apply to the authorized repair center, but remember that it will not be regarded as warranty case. The phone doesn't ring when a call or message arrives Make sure that Do Not Disturb mode (go to Settings > Sound & notification > Do Not Disturb) is not activated. Press the Volume up/down key to adjust volume. 18 I forget some passwords/codes/keys on phone Perform Factory data reset. If you still cannot access your phone, apply to the authorized repair center, but remember that it will not be regarded as warranty case. alcatel is a trademark of Alcatel-Lucent and is used under license by TCL Communication Ltd. Copyright 2018 TCL Communication Ltd All rights reserved TCL Communication Ltd reserves the right to alter material or technical specification without prior notice. All "Signature" ringtones embedded in this phone have been composed, arranged, and mixed by NU TROPIC (Amar Kabouche). 19

Safety and Precautions www.sar-tick.com This product meets applicable national SAR limits of 1.6 W/kg. The specific maximum SAR values can be found in the Radio waves section. When carrying the product or using it while worn on your body, either use an approved accessory such as a holster or otherwise maintain a distance of 10 mm from the body to ensure compliance with RF exposure requirements. Note that the product may be transmitting even if you are not making a phone call. PROTECT YOUR HEARING To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise caution when holding your phone near your ear while the loudspeaker is in use. English - CQF2B0802AAA Printed in China Safety and use We recommend that you read this chapter carefully before using your phone. The manufacturer disclaims any liability for damage, which may result as a consequence of improper use or use contrary to the instructions contained herein. TRAFFIC SAFETY:

Given that studies show that using a phone while driving a vehicle constitutes a real risk, even when the hands-free kit is used (car kit, headset...), drivers are requested to refrain from using their phone when the vehicle is not parked. Check the laws and regulations on the use of wireless phones and their accessories in the areas where you drive. Always obey them. The use of these devices may be prohibited or restricted in certain areas. CONDITIONS OF USE:

You are advised to switch off the phone from time to time to optimize its performance;

Remember to abide by local authority rules of mobile phone use on aircrafts;

If your phone is a unibody device, where the back cover and battery are not removable, disassembling the phone will void your warranty. Disassembling the phone can cause bodily injury if the battery is punctured;

Always handle your phone with care and keep it in a clean and dust-free place;

Do not allow your phone to be exposed to adverse weather or environmental conditions, such as moisture, humidity, rain, infiltration of liquids, dust, sea air, etc. The manufacturers recommended operating temperature range is -10C (14F) to +45C (113F). At over 45C (113F), the legibility of the phones display may be temporarily impaired;

Do not open, dismantle, or attempt to repair your phone yourself;

Do not drop, throw, or bend your phone;

1 Use only batteries, battery chargers, and accessories which are recommended by TCL Communication Ltd. and its affiliates and are compatible with your phone model. TCL Communication Ltd. and its affiliates disclaim any liability for damage caused by the use of other chargers or batteries;

Your phone should not be disposed of in a municipal waste. Please check local regulations for disposal of electronic products;

Remember to make backup copies or keep a written record of all important information stored on your phone;

Some people may suffer epileptic seizures or blackouts when exposed to flashing lights, or when playing video games. These seizures or blackouts may occur even if a person never had a previous seizure or blackout. If you have experienced seizures or blackouts, or if you have a family history of such occurrences, please consult your doctor before playing video games on your phone or enabling a flashing-lights feature on your phone;

Parents should monitor their childrens use of video games or other features that incorporate flashing lights on the phones. All persons should discontinue use and consult a doctor if any of the following symptoms occur: convulsion, eye or muscle twitching, loss of awareness, orientation, or movements. PRIVACY:

Please note that you must respect the laws and regulations in force in your jurisdiction or other jurisdiction(s) where you will use your phone regarding taking photographs and recording sounds with your phone. Pursuant to such laws and regulations, it may be strictly forbidden to take photographs and/or to record the voices of other people or any of their personal attributes, and reproduce or distribute them, as this may be considered to be an invasion of privacy. It is the user's sole responsibility to ensure that prior authorization has been obtained, if necessary, in order to record private or confidential conversations or take a photograph of another person; the manufacturer, the seller or vendor of your phone (including the carrier) disclaim any liability which may result from improper use of the phone. 2 BATTERY:

For a non-unibody device:

Observe the following precautions:

Do not attempt to open the battery (due to the risk of toxic fumes and burns);

Do not puncture, disassemble, or cause a short circuit in the battery;

Do not burn or dispose of a used battery in household garbage or store it at temperatures above 60C (140F). Batteries must be disposed of in accordance with locally applicable environmental regulations. Only use the battery for the purpose for which it was designed. Never use damaged batteries or those not recommended by TCL Communication Ltd. and/or its affiliates. For a non-unibody device with a non-removable battery:

Observe the following precautions:

Do not attempt to eject, replace, or open the battery;

Do not puncture, disassemble, or cause a short circuit in the battery;

Do not burn or dispose of your phone in household garbage or store it at temperature above 60C (140F). Phone and battery must be disposed of in accordance with locally applicable environmental regulations. For a unibody device:

Observe the following precautions:

Do not attempt to open the back cover;

Do not attempt to eject, replace, or open the battery;

3 Do not puncture the back cover of your phone;

Do not burn or dispose of your phone in household rubbish or store it at temperature above 60C (140F);

Phone and battery as a unibody device must be disposed of in accordance with locally applicable environmental regulations. This symbol on your phone, the battery, and the accessories means that these products must be taken to collection points at the end of their life:

Municipal waste disposal centers with specific bins for these types of equipment;

Collection bins at points of sale. They will then be recycled, preventing substances being disposed of in the environment, so that their components can be reused. In European Union countries:

These collection points are accessible free of charge. All products with this sign must be brought to these collection points. In non-European Union jurisdictions:

Items of equipment with this symbol are not to be thrown into ordinary bins if your jurisdiction or your region has suitable recycling and collection facilities; instead they are to be taken to collection points for them to be recycled. In the United States you may learn more about CTIAs Recycling Program at http://www.gowirelessgogreen.org/

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 4 CHARGERS:

Home A.C./ Travel chargers will operate within the temperature range of: 0C (32F) to 40C (104F). The chargers designed for your phone meet the standard for safety of information technology equipment and office equipment use. Due to different applicable electrical specifications, a charger you purchased in one jurisdiction may not work in another jurisdiction. They should be used for this purpose only. Characteristics of power supply (depending on the country):

Travel charger: Input: 100-240V,50/60Hz, 150mA Battery:

Output:5V,550mA Lithium 2000 mAh Radio waves THIS PHONE MEETS THE GOVERNMENTS REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio-frequency (RF) energy. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. These guidelines include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. The exposure standard for phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by public authorities such as the Federal Communications Commission of the US Government (FCC), or by Innovation, Science and Economic Development Canada (ISEDC), is 1.6 W/kg averaged over 1 gram of body tissue. Tests for SAR are conducted using standard operating positions with the phone transmitting at its highest certified power level in all tested frequency bands. 5 This device is complied with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/

oet/ea/fccid after searching on FCC ID : 2ACCJH089 Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output of the phone. Before a phone model is available for sale to the public, compliance with national regulations and standards must be shown. The highest SAR value for 5033M when tested is 0.99 W/Kg for use at the ear and 1.26 W/Kg for use close to the body. The highest SAR value for 5033E when tested is 0.99 W/Kg for use at the ear and 1.28 W/Kg for use close to the body. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for RF exposure. For body-worn operation, the phone meets FCC RF exposure guidelines provided that it is used with a non-metallic accessory with the handset at least 10 mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Additional information on SAR can be found on the Cellular Telecommunications & Internet Association (CTIA) Web site: http://www.ctia.org/

The World Health Organization (WHO) considers that present scientific information does not indicate the need for any special precautions for use of phones. If individuals are concerned, they may choose to limit their own or their childrens RF exposure by limiting the length of calls, or using hands-

free devices to keep phones away from the head and body. Additional WHO information about electromagnetic fields and public health are available on the following website: http://www.who.int/peh-emf. 6 Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna;

Increase the separation between the equipment and receiver;

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;

Consult the dealer or an experienced radio/ TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. For the receiver devices associated with the operation of a licensed radio service (e.g. FM broadcast), they bear the following statement:

This phone complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference;

This device must accept any interference received, including interference that may cause undesired operation. Your phone is equipped with a built-in antenna. For optimal operation, you should avoid touching it or degrading it. As mobile devices offer a range of functions, they can be used in positions other than against your ear. In such circumstances the device will be compliant with the guidelines when used with a headset or usb data cable. If you are using another accessory ensure that whatever product is used is free of any metal and that it positions the phone at least 10 mm away from the body. 7 Please note by using the device some of your personal data may be shared with the main device. It is under your own responsibility to protect your own personal data, not to share with it with any unauthorized devices or third party devices connected to yours. For products with Wi-Fi features, only connect to trusted Wi-Fi networks. Also when using your product as a hotspot (where available), use network security. These precautions will help prevent unauthorized access to your device. Your product can store personal information in various locations including a SIM card, memory card, and built-in memory. Be sure to remove or clear all personal information before you recycle, return, or give away your product. Choose your apps and updates carefully, and install from trusted sources only. Some apps can impact your products performance and/or have access to private information including account details, call data, location details and network resources. Note that any data shared with TCL Communication Ltd. is stored in accordance with applicable data protection legislation. For these purposes TCL Communication Ltd. implements and maintains appropriate technical and organizational measures to protect all personal data, for example against unauthorized or unlawful processing and accidental loss or destruction of or damage to such personal data whereby the measures shall provide a level of security that is appropriate having regard to The technical possibilities available;

The costs for implementing the measures;

The risks involved with the processing of the personal data, and;

The sensitivity of the personal data processed. You can access, review, and edit your personal information at any time by logging into your user account, visiting your user profile or by contacting us directly. Should you require us to edit or delete your personal data, we may ask you to provide us with evidence of your identity before we can act on your request. 8 Licenses microSD Logo is a trademark. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by TCL Communication Ltd. and its affiliates is under licence. Other trademarks and trade names are those of their respective owners. Alcatel 5033M/5033E Bluetooth Declaration ID D038401 The Wi-Fi Logo is a certification mark of the Wi-Fi Alliance. Google, the Google logo, Android, the Android logo, Google Search TM, Google Maps TM, Gmail TM, YouTube, Google Play Store, Google Latitude TM, and Hangouts TM are trademarks of Google Inc. The Android robot is reproduced or modified from work created and shared by Google and used according to terms described in the Creative Commons 3.0 Attribution License (the text will show when you touch Google legal in Settings > About phone > Legal information) (1). You have purchased a product which uses the open source (http://opensource.org/) programs mtd, msdosfs, netfilter/iptables and initrd in object code and other open source programs licensed under the GNU General Public Licence and Apache Licence. We will provide you with a complete copy of the corresponding source codes upon request within a period of three years from the distribution of the product by TCL Communication Ltd. You may download the source codes from http://sourceforge.net/projects/alcatel/files/. The provision of the source code is free of charge from the internet.

(1) May not be available in all countries. 9 General information Internet address: www.alcatelmobile.com Hotline: See the "SERVICES" leaflet that came with your phone or go to our website. Manufacturer: TCL Communication Ltd. Address: 5/F, Building 22E, 22 Science Park East Avenue, Hong Kong Science Park, Shatin, NT, Hong Kong Electronic labeling path: Touch Settings > Regulatory & safety or press *#07# to find more information about labeling (1), such as FCC ID. On our website, you will find our FAQ (Frequently Asked Questions) section. You can also contact us by email to ask any questions you may have. Your phone is a transceiver that operates on GSM in quad-band (850/900/1800/1900 MHz), UMTS in penta-band (B1/2/4/5/8) or LTE

(B1/2/3/4/5/7/8/12/13/17/28). Protection against theft (2) Your phone is identified by an IMEI (phone serial number) shown on the packaging label and in the phones memory. We recommend that you note the number the first time you use your phone by entering *#06# and keep it in a safe place. It may be requested by the police or your carrier if your phone is stolen. This number allows your phone to be blocked preventing a third person from using it, even with a different SIM card. Disclaimer There may be certain differences between the user manual description and the phones operation, depending on the software release of your phone or specific carrier services.

(1) This may vary depending on country.

(2) Contact your service provider to check service availability. 10 TCL Communication Ltd. shall not be held legally responsible for such differences, if any, nor for their potential consequences, which responsibility shall be borne by the carrier exclusively. Warranty Your phone is warranted against any defect or malfunctioning which may occur in conditions of normal use during the warranty period of twelve (12) months (1) from the date of purchase as shown on your original invoice. Batteries (2) and accessories sold with your phone are also warranted against any defect which may occur during the first six (6) months (1) from the date of purchase as shown on your original invoice. In case of any defect of your phone which prevents you from normal use thereof, you must immediately inform your vendor and present your phone with your proof of purchase. If the defect is confirmed, your phone or part thereof will be either replaced or repaired, as appropriate. Repaired phone and accessories are entitled to a one (1) month warranty for the same defect. Repair or replacement may be carried out using reconditioned components offering equivalent functionality. This warranty covers the cost of parts and labor but excludes any other costs. This warranty shall not apply to defects to your phone and/or accessory due to (without any limitation):

- Non-compliance with the instructions for use or installation, or with technical and safety standards applicable in the geographical area where your phone is used;

(1) The warranty period may vary depending on your country.

(2) The life of a rechargeable phone battery in terms of conversation time, standby time and total service life, will depend on the conditions of use and network configuration. Batteries being considered expendable supplies, the specifications state that you should obtain optimal performance for your phone during the first six months after purchase and for approximately 200 more recharges. 11

- Connection to any equipment not supplied or not recommended by TCL Communication Ltd.;

- Modification or repair performed by individuals not authorised by TCL Communication Ltd. or its affiliates or your vendor;

- Modification, adjustment or alteration of software or hardware performed by individuals not authorised by TCL Communication Ltd.;

- Inclement weather, lightning, fire, humidity, infiltration of liquids or foods, chemical products, download of files, crash, high voltage, corrosion, oxidation Your phone will not be repaired in case labels or serial numbers (IMEI) have been removed or altered. There are no express warranties, whether written, oral or implied, other than this printed limited warranty or the mandatory warranty provided by your country or jurisdiction. In no event shall TCL Communication Ltd. or any of its affiliates be liable for indirect, incidental or consequential damages of any nature whatsoever, including but not limited to commercial or financial loss or damage, loss of data or loss of image to the full extent those damages can be disclaimed by law. Some countries/states do not allow the exclusion or limitation of indirect, incidental or consequential damages, or limitation of the duration of implied warranties, so the preceding limitations or exclusions may not apply to you. 12

Safety and Precautions www.sar-tick.com This product meets applicable national SAR limits of 1.6 W/kg. The specific maximum SAR values can be found in the Radio waves section. When carrying the product or using it while worn on your body, either use an approved accessory such as a holster or otherwise maintain a distance of 10 mm from the body to ensure compliance with RF exposure requirements. Note that the product may be transmitting even if you are not making a phone call. PROTECT YOUR HEARING To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise caution when holding your phone near your ear while the loudspeaker is in use. English - CQF2B0802AAA Printed in China Safety and use We recommend that you read this chapter carefully before using your phone. The manufacturer disclaims any liability for damage, which may result as a consequence of improper use or use contrary to the instructions contained herein. TRAFFIC SAFETY:

Given that studies show that using a phone while driving a vehicle constitutes a real risk, even when the hands-free kit is used (car kit, headset...), drivers are requested to refrain from using their phone when the vehicle is not parked. Check the laws and regulations on the use of wireless phones and their accessories in the areas where you drive. Always obey them. The use of these devices may be prohibited or restricted in certain areas. CONDITIONS OF USE:

You are advised to switch off the phone from time to time to optimize its performance;

Remember to abide by local authority rules of mobile phone use on aircrafts;

If your phone is a unibody device, where the back cover and battery are not removable, disassembling the phone will void your warranty. Disassembling the phone can cause bodily injury if the battery is punctured;

Always handle your phone with care and keep it in a clean and dust-free place;

Do not allow your phone to be exposed to adverse weather or environmental conditions, such as moisture, humidity, rain, infiltration of liquids, dust, sea air, etc. The manufacturers recommended operating temperature range is -10C (14F) to +45C (113F). At over 45C (113F), the legibility of the phones display may be temporarily impaired;

Do not open, dismantle, or attempt to repair your phone yourself;

Do not drop, throw, or bend your phone;

1 Use only batteries, battery chargers, and accessories which are recommended by TCL Communication Ltd. and its affiliates and are compatible with your phone model. TCL Communication Ltd. and its affiliates disclaim any liability for damage caused by the use of other chargers or batteries;

Your phone should not be disposed of in a municipal waste. Please check local regulations for disposal of electronic products;

Remember to make backup copies or keep a written record of all important information stored on your phone;

Some people may suffer epileptic seizures or blackouts when exposed to flashing lights, or when playing video games. These seizures or blackouts may occur even if a person never had a previous seizure or blackout. If you have experienced seizures or blackouts, or if you have a family history of such occurrences, please consult your doctor before playing video games on your phone or enabling a flashing-lights feature on your phone;

Parents should monitor their childrens use of video games or other features that incorporate flashing lights on the phones. All persons should discontinue use and consult a doctor if any of the following symptoms occur: convulsion, eye or muscle twitching, loss of awareness, orientation, or movements. PRIVACY:

Please note that you must respect the laws and regulations in force in your jurisdiction or other jurisdiction(s) where you will use your phone regarding taking photographs and recording sounds with your phone. Pursuant to such laws and regulations, it may be strictly forbidden to take photographs and/or to record the voices of other people or any of their personal attributes, and reproduce or distribute them, as this may be considered to be an invasion of privacy. It is the user's sole responsibility to ensure that prior authorization has been obtained, if necessary, in order to record private or confidential conversations or take a photograph of another person; the manufacturer, the seller or vendor of your phone (including the carrier) disclaim any liability which may result from improper use of the phone. 2 BATTERY:

For a non-unibody device:

Observe the following precautions:

Do not attempt to open the battery (due to the risk of toxic fumes and burns);

Do not puncture, disassemble, or cause a short circuit in the battery;

Do not burn or dispose of a used battery in household garbage or store it at temperatures above 60C (140F). Batteries must be disposed of in accordance with locally applicable environmental regulations. Only use the battery for the purpose for which it was designed. Never use damaged batteries or those not recommended by TCL Communication Ltd. and/or its affiliates. For a non-unibody device with a non-removable battery:

Observe the following precautions:

Do not attempt to eject, replace, or open the battery;

Do not puncture, disassemble, or cause a short circuit in the battery;

Do not burn or dispose of your phone in household garbage or store it at temperature above 60C (140F). Phone and battery must be disposed of in accordance with locally applicable environmental regulations. For a unibody device:

Observe the following precautions:

Do not attempt to open the back cover;

Do not attempt to eject, replace, or open the battery;

3 Do not puncture the back cover of your phone;

Do not burn or dispose of your phone in household rubbish or store it at temperature above 60C (140F);

Phone and battery as a unibody device must be disposed of in accordance with locally applicable environmental regulations. This symbol on your phone, the battery, and the accessories means that these products must be taken to collection points at the end of their life:

Municipal waste disposal centers with specific bins for these types of equipment;

Collection bins at points of sale. They will then be recycled, preventing substances being disposed of in the environment, so that their components can be reused. In European Union countries:

These collection points are accessible free of charge. All products with this sign must be brought to these collection points. In non-European Union jurisdictions:

Items of equipment with this symbol are not to be thrown into ordinary bins if your jurisdiction or your region has suitable recycling and collection facilities; instead they are to be taken to collection points for them to be recycled. In the United States you may learn more about CTIAs Recycling Program at http://www.gowirelessgogreen.org/

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 4 CHARGERS:

Home A.C./ Travel chargers will operate within the temperature range of: 0C (32F) to 40C (104F). The chargers designed for your phone meet the standard for safety of information technology equipment and office equipment use. Due to different applicable electrical specifications, a charger you purchased in one jurisdiction may not work in another jurisdiction. They should be used for this purpose only. Characteristics of power supply (depending on the country):

Travel charger: Input: 100-240V,50/60Hz, 150mA Battery:

Output:5V,550mA Lithium 2000 mAh Radio waves THIS PHONE MEETS THE GOVERNMENTS REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio-frequency (RF) energy. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. These guidelines include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. The exposure standard for phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by public authorities such as the Federal Communications Commission of the US Government (FCC), or by Innovation, Science and Economic Development Canada (ISEDC), is 1.6 W/kg averaged over 1 gram of body tissue. Tests for SAR are conducted using standard operating positions with the phone transmitting at its highest certified power level in all tested frequency bands. 5 This device is complied with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measurement methods and procedures specified in IEEE1528. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/

oet/ea/fccid after searching on FCC ID : 2ACCJH089 Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output of the phone. Before a phone model is available for sale to the public, compliance with national regulations and standards must be shown. The highest SAR value for 5033M/5033E when tested is 0.99 W/Kg for use at the ear and 1.26 W/Kg for use close to the body. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for RF exposure. For body-worn operation, the phone meets FCC RF exposure guidelines provided that it is used with a non-metallic accessory with the handset at least 10 mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Additional information on SAR can be found on the Cellular Telecommunications & Internet Association (CTIA) Web site: http://www.ctia.org/

The World Health Organization (WHO) considers that present scientific information does not indicate the need for any special precautions for use of phones. If individuals are concerned, they may choose to limit their own or their childrens RF exposure by limiting the length of calls, or using hands-

free devices to keep phones away from the head and body. Additional WHO information about electromagnetic fields and public health are available on the following website: http://www.who.int/peh-emf. 6 Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna;

Increase the separation between the equipment and receiver;

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected;

Consult the dealer or an experienced radio/ TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. For the receiver devices associated with the operation of a licensed radio service (e.g. FM broadcast), they bear the following statement:

This phone complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference;

This device must accept any interference received, including interference that may cause undesired operation. Your phone is equipped with a built-in antenna. For optimal operation, you should avoid touching it or degrading it. As mobile devices offer a range of functions, they can be used in positions other than against your ear. In such circumstances the device will be compliant with the guidelines when used with a headset or usb data cable. If you are using another accessory ensure that whatever product is used is free of any metal and that it positions the phone at least 10 mm away from the body. 7 Please note by using the device some of your personal data may be shared with the main device. It is under your own responsibility to protect your own personal data, not to share with it with any unauthorized devices or third party devices connected to yours. For products with Wi-Fi features, only connect to trusted Wi-Fi networks. Also when using your product as a hotspot (where available), use network security. These precautions will help prevent unauthorized access to your device. Your product can store personal information in various locations including a SIM card, memory card, and built-in memory. Be sure to remove or clear all personal information before you recycle, return, or give away your product. Choose your apps and updates carefully, and install from trusted sources only. Some apps can impact your products performance and/or have access to private information including account details, call data, location details and network resources. Note that any data shared with TCL Communication Ltd. is stored in accordance with applicable data protection legislation. For these purposes TCL Communication Ltd. implements and maintains appropriate technical and organizational measures to protect all personal data, for example against unauthorized or unlawful processing and accidental loss or destruction of or damage to such personal data whereby the measures shall provide a level of security that is appropriate having regard to The technical possibilities available;

The costs for implementing the measures;

The risks involved with the processing of the personal data, and;

The sensitivity of the personal data processed. You can access, review, and edit your personal information at any time by logging into your user account, visiting your user profile or by contacting us directly. Should you require us to edit or delete your personal data, we may ask you to provide us with evidence of your identity before we can act on your request. 8 Licenses microSD Logo is a trademark. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by TCL Communication Ltd. and its affiliates is under licence. Other trademarks and trade names are those of their respective owners. Alcatel 5033M/5033E Bluetooth Declaration ID D038401 The Wi-Fi Logo is a certification mark of the Wi-Fi Alliance. Google, the Google logo, Android, the Android logo, Google Search TM, Google Maps TM, Gmail TM, YouTube, Google Play Store, Google Latitude TM, and Hangouts TM are trademarks of Google Inc. The Android robot is reproduced or modified from work created and shared by Google and used according to terms described in the Creative Commons 3.0 Attribution License (the text will show when you touch Google legal in Settings > About phone > Legal information) (1). You have purchased a product which uses the open source (http://opensource.org/) programs mtd, msdosfs, netfilter/iptables and initrd in object code and other open source programs licensed under the GNU General Public Licence and Apache Licence. We will provide you with a complete copy of the corresponding source codes upon request within a period of three years from the distribution of the product by TCL Communication Ltd. You may download the source codes from http://sourceforge.net/projects/alcatel/files/. The provision of the source code is free of charge from the internet.

(1) May not be available in all countries. 9 General information Internet address: www.alcatelmobile.com Hotline: See the "SERVICES" leaflet that came with your phone or go to our website. Manufacturer: TCL Communication Ltd. Address: 5/F, Building 22E, 22 Science Park East Avenue, Hong Kong Science Park, Shatin, NT, Hong Kong Electronic labeling path: Touch Settings > Regulatory & safety or press *#07# to find more information about labeling (1), such as FCC ID. On our website, you will find our FAQ (Frequently Asked Questions) section. You can also contact us by email to ask any questions you may have. Your phone is a transceiver that operates on GSM in quad-band (850/900/1800/1900 MHz), UMTS in penta-band (B1/2/4/5/8) or LTE

(B1/2/3/4/5/7/8/12/13/17/28). Protection against theft (2) Your phone is identified by an IMEI (phone serial number) shown on the packaging label and in the phones memory. We recommend that you note the number the first time you use your phone by entering *#06# and keep it in a safe place. It may be requested by the police or your carrier if your phone is stolen. This number allows your phone to be blocked preventing a third person from using it, even with a different SIM card. Disclaimer There may be certain differences between the user manual description and the phones operation, depending on the software release of your phone or specific carrier services.

(1) This may vary depending on country.

(2) Contact your service provider to check service availability. 10 TCL Communication Ltd. shall not be held legally responsible for such differences, if any, nor for their potential consequences, which responsibility shall be borne by the carrier exclusively. Warranty Your phone is warranted against any defect or malfunctioning which may occur in conditions of normal use during the warranty period of twelve (12) months (1) from the date of purchase as shown on your original invoice. Batteries (2) and accessories sold with your phone are also warranted against any defect which may occur during the first six (6) months (1) from the date of purchase as shown on your original invoice. In case of any defect of your phone which prevents you from normal use thereof, you must immediately inform your vendor and present your phone with your proof of purchase. If the defect is confirmed, your phone or part thereof will be either replaced or repaired, as appropriate. Repaired phone and accessories are entitled to a one (1) month warranty for the same defect. Repair or replacement may be carried out using reconditioned components offering equivalent functionality. This warranty covers the cost of parts and labor but excludes any other costs. This warranty shall not apply to defects to your phone and/or accessory due to (without any limitation):

- Non-compliance with the instructions for use or installation, or with technical and safety standards applicable in the geographical area where your phone is used;

(1) The warranty period may vary depending on your country.

(2) The life of a rechargeable phone battery in terms of conversation time, standby time and total service life, will depend on the conditions of use and network configuration. Batteries being considered expendable supplies, the specifications state that you should obtain optimal performance for your phone during the first six months after purchase and for approximately 200 more recharges. 11

- Connection to any equipment not supplied or not recommended by TCL Communication Ltd.;

- Modification or repair performed by individuals not authorised by TCL Communication Ltd. or its affiliates or your vendor;

- Modification, adjustment or alteration of software or hardware performed by individuals not authorised by TCL Communication Ltd.;

- Inclement weather, lightning, fire, humidity, infiltration of liquids or foods, chemical products, download of files, crash, high voltage, corrosion, oxidation Your phone will not be repaired in case labels or serial numbers (IMEI) have been removed or altered. There are no express warranties, whether written, oral or implied, other than this printed limited warranty or the mandatory warranty provided by your country or jurisdiction. In no event shall TCL Communication Ltd. or any of its affiliates be liable for indirect, incidental or consequential damages of any nature whatsoever, including but not limited to commercial or financial loss or damage, loss of data or loss of image to the full extent those damages can be disclaimed by law. Some countries/states do not allow the exclusion or limitation of indirect, incidental or consequential damages, or limitation of the duration of implied warranties, so the preceding limitations or exclusions may not apply to you. 12

Date: Nov. 26, 20 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID: 2ACCJH089 Original Grant Date: Nov, 17th, 2020 Applicant: TCL Communication Ltd. Dear Examiner, This is to request a Class II permissive change for FCC ID: 2ACCJH089

, originally granted on 11/17/2020 The major change filed under this application is:

SOFTWARE MODIFICATIONS:

Protocol Stack changes: No MMS/STK/USAT/USIM changes: No DM/SUPL/VT/FUMO/SWP/HCI: No Other changes detailed:

HARDWARE MODIFICATIONS:

Band changes: No PCB Layout changes: NO Main components changes:

Anten na Transceiv er GSM850 GSM900 GSM1800 GSM1900 UMTS210 0 NO NO NO NO NO Base Ban d NO NO NO NO NO NO NO NO NO NO ASM Power Amplifi er NO NO Tx SAW Filter NO Rx SAW Filter NO NO NO NO NO NO NO NO NO NO NO NO NO Duple xer NO NO NO NO NO NO NO NO NO UMTS190 NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO 0 UMTS170 0 UMTS900 UMTS850 LTE 1 LTE 2 LTE 3 LTE 4 LTE 5 LTE 7 LTE 8 LTE 12 LTE 13 LTE 17 NO NO NO NO NO NO NO NO NO NO NO NO NO LTE 28 Bluetooth NO NO WiFi NFC NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA FM changes: No Other components changes:

LCD/ Speaker/ Camera/ Vibrator changes: No Other changes detailed: memory changed from 8+1 to 16+1, and the chipset is pin to pin compatible. MECHANICAL MODIFICATIONS:

Use new metal front/back cover or keypad: No Mechanical shell changes:

Whole size of EUT: No Distance of Ear reference point to bottom of handset: No Other trinkets to change the surface of handset: No Other changes detailed:

We request permission to partially use LTE / UMTS / GSM mobile phone test results from model 5033A (FCC ID:

2ACCJH089) in our applications for model 5033M (FCC ID: 2ACCJH089). You can find details next page:

For the above, we performed 2 points spot check for SAR, partially re-used the test results of 5033A for other parts. In Class II permissive change for FCC ID: 2ACCJH089, originally granted on 06/18/2019.We have been test and verify Part15B RE TCs. As below. For details, please refer to the relevant test reports. 1 FCC testing and certification Items 1.1 SAR part 1.1.1 GSM mobile phone FCC certification SAR testing Band Comment 850,1900 spot check for LTE mobile phone FCC 1.1.2 certification SAR testing acc to Oet65 FDD7,FDD2,FDD5,FDD 12,FDD13,FDD4 1.1.3 UMTS mobile phone FCC certification SAR testing 1900,1700,850 share basic model 85019002 points additional 1 battery FDD7FDD2FDD5 FDD12FDD13 FDD4share basic model results 19001700850 results Sincerely yours, Zi Xiaogang

Date 2020-11-09 To: Federal Communications Commission, Authorization & Evaluation Division, 7345 Oakland Mills Road Columbia, MD 21046 And American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

CTTL-Telecommunication Technology Labs, Academy of Telecommunication Research, MIIT is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, which includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR1.2002 (b) to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you. Regards, Zhizhou GONG Product Certification Manager TCL Communication Ltd. TCL Communication Ltd. 5F, C building, No. 232, Liang Jing Road, ZhangJiang High-Tech Park, Pudong Shanghai, P.R. China. 201203 Tel: +86 21 6146 0666 Fax: +86 21 6146 0602 http://tclcom.tcl.com TCL Communication Ltd. 5F, C building, No. 232, Liang Jing Road, ZhangJiang High-Tech Park, Pudong Shanghai, P.R. China. 201203 Tel: +86 21 6146 0666 Fax: +86 21 6146 0602 http://tclcom.tcl.com

Date: Nov. 9, 20 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID: 2ACCJH089 Original Grant Date: Jul., 29th, 2019 Applicant: TCL Communication Ltd. Dear Examiner, This is to request a Class II permissive change for FCC ID: 2ACCJH089

, originally granted on Jul., 29th, 2019 The major change filed under this application is:

Add a battery. Sincerely yours, Zhizhou GONG Product Certification Manager TCL Communication Ltd. TCL Communication Ltd. 5/F, Building 22E, 22 Science Park East 55 Avenue des Champs Pierreux, Avenue, Hong Kong Science Park, Shatin, Immeuble Le Capitole 92000 Nanterre http://tclcom.tcl.com

No No No No Declaration of changes from 5033E to 5033E General: 5033E is a variant product of 5033E SOFTWARE MODIFICATIONS:

Protocol Stack changes: No MMS/STK/USAT/USIM changes: No DM/SUPL/VT/FUMO/SWP/HCI: No (indicated the changed items if yes) Other changes detailed: No Antenna AP Modem Transceiver Rx SAW Filter ASM HARDWARE MODIFICATIONS:

Band changes: No PCB Layout changes: No Main RF components changes:NO No GSM850 No GSM900 GSM1800 No GSM1900 No No No No No No No No No No No No No NA NA UMTS210 0 UMTS190 0 UMTS170 0 UMTS900 NA UMTS850 NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA Power Amplifier No No No No No No No No Power Amplifie r NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA Antenna AP Modem Transceiver Tx SAW Filter Duple xer ASM LTE Band x LTE Band x Ante nna NA AP NA Mode m NA Transcei ver NA Power Amplifier NA Tx SAW Filter NA Rx SAW Filter NA Duplexe r NA NA NA NA NA NA NA NA NA ASM NA NA Antenna AP Modem Transceiver Balun Diplexer Power Amplifie r No NA Band pass filter No NA No NA No NA No NA Bluetooth No NA Wi-Fi FM changes: No LCD/ Speaker/ Camera/ Vibrator changes: (indicated the changed items if yes) No Other changes detailed: yes Add a battery No NA No NA Accessories Battery Charger USB Cable Headset

5033E ALCATEL 5033E ALCATEL CAB1930012CA Remark Add a battery MECHANICAL MODIFICATIONS:

Use new metal front/back cover or keypad: No Mechanical shell changes:

Whole size of EUT: No Distance of Ear reference point to bottom of handset: No Other trinkets to change the surface of handset: No Other changes detailed:

APPROVED BY:

Project Manager:

Signature:

Date: 2020-11-06

Date: Nov. 17, 20 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attn: OET Dept. Ref: FCC Class II Permissive change for FCC ID: 2ACCJH089 Original Grant Date: May. 11th ,2018. Applicant: TCL Communication Ltd. Dear Examiner, This is to request a Class II permissive change for FCC ID: 2ACCJH089

, originally granted on May. 11th ,2018. The major change filed under this application is:

Add a battery. Sincerely yours, Zhizhou GONG Product Certification Manager TCL Communication Ltd. TCL Communication Ltd. 5/F, Building 22E, 22 Science Park East 55 Avenue des Champs Pierreux, Avenue, Hong Kong Science Park, Shatin, Immeuble Le Capitole 92000 Nanterre http://tclcom.tcl.com

No No No No Declaration of changes from 5033A to 5033A General: 5033A is a variant product of 5033A SOFTWARE MODIFICATIONS:

Protocol Stack changes: No MMS/STK/USAT/USIM changes: No DM/SUPL/VT/FUMO/SWP/HCI: No (indicated the changed items if yes) Other changes detailed: No Antenna AP Modem Transceiver Rx SAW Filter ASM HARDWARE MODIFICATIONS:

Band changes: No PCB Layout changes: No Main RF components changes:NO No GSM850 No GSM900 GSM1800 No GSM1900 No No No No No No No No No No No No No NA NA UMTS210 0 UMTS190 0 UMTS170 0 UMTS900 NA UMTS850 NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA Power Amplifier No No No No No No No No Power Amplifie r NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA NA Antenna AP Modem Transceiver Tx SAW Filter Duple xer ASM LTE Band x LTE Band x Ante nna NA AP NA Mode m NA Transcei ver NA Power Amplifier NA Tx SAW Filter NA Rx SAW Filter NA Duplexe r NA NA NA NA NA NA NA NA NA ASM NA NA Antenna AP Modem Transceiver Balun Diplexer Power Amplifie r No NA Band pass filter No NA No NA No NA No NA Bluetooth No NA Wi-Fi FM changes: No LCD/ Speaker/ Camera/ Vibrator changes: (indicated the changed items if yes) No Other changes detailed: yes Add a battery No NA No NA Accessories Battery Charger USB Cable Headset

5033A ALCATEL 5033A ALCATEL CAB1930012CA Remark Add a battery MECHANICAL MODIFICATIONS:

Use new metal front/back cover or keypad: No Mechanical shell changes:

Whole size of EUT: No Distance of Ear reference point to bottom of handset: No Other trinkets to change the surface of handset: No Other changes detailed:

APPROVED BY:

Project Manager:

Signature:

Date: 2020-11-10

2019-07-29 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland21046 Subject: FCC ClassII Permissive change for FCC ID: 2ACCJH089 To Whom It May Concern, This is to request a ClassII Permissive change for FCC ID: 2ACCJH089, originally granted on May. 11th ,2018. The Major change filed under this application is as below. 1. Memory changed from 8+1 to 16+1, the memory chip is pin to pin compatible;

2. Changed from single SIM to dual SIM, but PCB layout is the same;

3. Software changed from 7LT2 to 7LTD, only updated some security patch. Others are fully same with basic model. Thank you. Sincerely, Zhizhou GONG Product Certification Manager TCL Communication Ltd. TCL Communication Ltd. 7/F, Block F4, TCL International E City, Zh zhong Shan Yuan Road, Nanshan District, shenzhen, Guangdong, P.R. China 518052 Tel: +0086-755-36611722 Fax: 0086-75536612000-81722 http://tclcom.tcl.com

201 9-07-29 Fed Offi Equ 734 Colu deral Comm fice of Engin uipment Aut 45 Oakland M umbia, Mar munications C neering and thorization Mills Road ryland 2104 46 Commission n d Technolog gy Division Sub bject: Perma anent Confid dentiality re equest for F FCC ID: 2A CCJH089 To W Purs con Whom It M suant to sec fidential tre n, May Concern 7 and 0.459 ctions 0.457 eatment of th he followin of CFR 47, ng informati the applica ion accompa ant requests anying this permanent application n:

am lock Diagra chematics perational D

- Bl

- Sc

- Op

BOOM list Description The rele appl e above mat eased to the licant and p erials conta public. The provide unju ain trade sec e public disc ustified bene crets and pro closure of th efits to its c nformation n oprietary in hese matter s might be h

. competitors not customa harmful to t arily the You urs Sincerel ly, Zhiz Prod TCL G zhou GONG duct Certifi cation Man nication Lt L Commun nager d. TCL Communic 7/F, B lock zhong Sh an h z henzhen, Gua sh Tel:0086-755-366 cation Ltd. F4, T CL I nt Yuan Ro ad, angdong, P.R 611722 Fax: 008 ernational E Nanshan D i

. China 5180 86-75536612000-

City, strict, 52

-81722 htt p://tclcom.tcl.co om

Date: Jul. 29, 19 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request permission to use Wi-Fi/BT/USB/GSM/WCDMA/LTE/SAR test results from model 5033A in our applications for model 5033E FCC ID: 2ACCJH089 To whom it may concern:

We request permission to use Wi-Fi/BT/USB/GSM/WCDMA/LTE/SAR test results from model 5033A (FCC ID: 2ACCJH089) in our applications for model 5033E

(FCC ID: 2ACCJH089). Changes:

1. Memory changed from 8+1 to 16+1, the memory chip is pin to pin compatible;

2. Changed from single SIM to dual SIM, but PCB layout is the same;

3. Software changed from 7LT2 to 7LTD, only updated some security patch. Others are fully same with basic model. For the above, we performed SAR spot check and Radiated Emission tests. The rest test results all come from the initial model 5033A. Sincerely yours, Zi Xiaogang

The Photos of SAR test No. I19Z61162-SEM01 For TCL Communication Ltd. LTE / UMTS / GSM mobile phone Model Name: 5033E With Hardware Version: 05 Software Version: v7LTD Note:

The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of CTTL. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S.Government. Test Laboratory:

CTTL, Telecommunication Technology Labs, CAICT No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2512, Fax:+86(0)10-62304633-2504 Email: cttl_terminals@caict.ac.cn, website: www.caict.ac.cn Copyright. All rights reserved by CTTL. Picture - 1 Constituents of the sample Picture - 2 Left Hand Touch Cheek Position Picture - 3 Left Hand Tilt 15 Position Picture - 4 Right Hand Touch Cheek Position Picture - 5 Right Hand Tilt 15 Position Test positions for body:

The Body SAR is tested at the following 6 test positions all with the distance =10mm between the EUT and the phantom bottom:

Picture - 6 Front Picture - 7 Rear Picture - 8 Left edge Picture - 9 Right edge Picture - 10 Bottom edge Picture - 11 Top edge

TEST REPORT No. I19Z61162-EMC01 for TCL Communication Ltd. LTE / UMTS / GSM mobile phone Model Name: 5033E FCC ID: 2ACCJH089 with Hardware Version: 05 Software Version: v7LTD Issued Date: 2019-07-26 Note:

The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of CTTL. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S.Government. Test Laboratory:

CTTL, Telecommunication Technology Labs, CAICT No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2512, Fax:+86(0)10-62304633-2504 Email: cttl_terminals@caict.ac.cn, website: www.caict.ac.cn Copyright. All rights reserved by CTTL. REPORT HISTORY No.I19Z61162-EMC01 Page 2 of 27 Report Number Revision I19Z61162-EMC01 I19Z61162-EMC01 Rev.0 Rev.1 Description 1st edition 2nd edition Issue Date 2019-07-11 2019-07-26 Copyright. All rights reserved by CTTL. CONTENTS No.I19Z61162-EMC01 Page 3 of 27 1. TEST LABORATORY ............................................................................................................... 4 1.1. TESTING LOCATION ........................................................................................................... 4 1.2. TESTING ENVIRONMENT ................................................................................................... 4 1.3. PROJECT DATA ................................................................................................................... 4 1.4. SIGNATURE .......................................................................................................................... 4 2. CLIENT INFORMATION ........................................................................................................... 5 2.1. CERTIFICATION CONTACT INFORMATION ...................................................................... 5 2.2. APPLICANT INFORMATION ................................................................................................ 5 2.3. MANUFACTURER INFORMATION ...................................................................................... 5 3. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ............................ 6 3.1. ABOUT EUT .......................................................................................................................... 6 3.2. INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST ................................... 6 3.3. INTERNAL IDENTIFICATION OF AE USED DURING THE TEST ...................................... 6 3.4. EUT SET-UPS ....................................................................................................................... 8 4. REFERENCE DOCUMENTS .................................................................................................... 9 4.1. REFERENCE DOCUMENTS FOR TESTING....................................................................... 9 5. LABORATORY ENVIRONMENT ............................................................................................ 10 6. SUMMARY OF TEST RESULTS ............................................................................................ 11 7. TEST EQUIPMENTS UTILIZED ............................................................................................. 12 ANNEX A: MEASUREMENT RESULTS ....................................................................................... 13 Copyright. All rights reserved by CTTL. No.I19Z61162-EMC01 Page 4 of 27 1. Test Laboratory 1.1. Testing Location CTTL(huayuan North Road) Address:

No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191 1.2. Testing Environment 15-35 20-75%

2018-04-12 2019-07-09 Normal Temperature:

Relative Humidity:

1.3. Project data Testing Start Date:

Testing End Date:

1.4. Signature Wang Junqing

(Prepared this test report) Zhang Ying

(Reviewed this test report) Liu Baodian Deputy Director of the laboratory

(Approved this test report) Copyright. All rights reserved by CTTL. 2. Client Information No.I19Z61162-EMC01 Page 5 of 27 2.1. Certification Contact Information Company Name:

Address /Post:

TCL Communication Ltd. 17 Huifeng 3th Road,ZhongKai Hi-tech Development District Huizhou,Guangdong 516006 P.R.China Contact Person:

Li Tingting Contact Email:

tingting.li@tcl.com Telephone:

0752-8228549 2.2. Applicant Information Company Name:

TCL Communication Ltd. Address /Post:

International E City, Zhong Shan Yuan Road, Nanshan District, 7/F, Block F4, TCL Communication Technology Building, TCL Shenzhen, Guangdong, P.R. China 518052 Contact Person:

Zhizhou Gong Contact Email:

zhizhou.gong@tcl.com 0086-755-36611722 Telephone:

2.3. Manufacturer Information Company Name:

TCL Communication Ltd. Address /Post:

International E City, Zhong Shan Yuan Road, Nanshan District, 7/F, Block F4, TCL Communication Technology Building, TCL Shenzhen, Guangdong, P.R. China 518052 Contact Person:

Zhizhou Gong Contact Email:

zhizhou.gong@tcl.com Telephone:

0086-755-36611722 Copyright. All rights reserved by CTTL. No.I19Z61162-EMC01 Page 6 of 27 3. Equipment Under Test (EUT) and Ancillary Equipment (AE) 3.1. About EUT Description Model Name FCC ID LTE / UMTS / GSM mobile phone 5033E 2ACCJH089 Extreme vol. Limits 3.5VDC to 4.4VDC (nominal: 3.8VDC) Note: Components list, please refer to documents of the manufacturer; it is also included in the original test record of CTTL, Telecommunication Technology Labs, Academy of Telecommunication Research, MIIT. 3.2. Internal Identification of EUT used during the test EUT ID*

SN or IMEI HW Version SW Version EUT1 358675100000030/

05 v7LTD 358675100000048

*EUT ID: is used to identify the test sample in the lab internally. 3.3. Internal Identification of AE used during the test AE ID* Description SN

/

/

/

/

/

/

/

/

/

/

AE1 AE2 AE3 AE4 AE5 AE6 AE7 AE8 AE9 Battery Charger Charger Charger USB Cable USB Cable Headset Headset Headset AE10 Headset AE1 Model Manufacturer Capacitance Remarks

/

18TCT-CH-0306 1860562CH004 1860562CH002 19TCT-DC-0003 18TCT-DC-0317 SH-0014 SH-0023 SH-0043 SH-0045 CAB1930000C7 Ningbo Veken Battery Co.,LTD 2000mAh Nominal voltage 3.85V AE2 Model CBA0066AGAC5 Manufacturer Length of cable AE3

/

HUIZHOU PUAN ELECTRONICS CO.,LTD Model CBA0066AGAC7 Manufacturer Length of cable JIANGSU CHENYANG ELECTRON CO.,LTD

/

Copyright. All rights reserved by CTTL. No.I19Z61162-EMC01 Page 7 of 27 AE4 Model CBA3068AGAC5 Manufacturer Length of cable AE5 HUIZHOU PUAN ELECTRONICS CO.,LTD

/

Model CDA3122005C1 Manufacturer Length of cable AE6 HUIZHOU JUWEI ELECTRONICS CO.,LTD 100cm Model CDA3122005C2 Manufacturer Length of cable Sheng Hua Industrial Co., Ltd 100cm AE7 Model CCB0046A10C4 Dongguan MeiHao Electronic Technology Co., Ltd. Manufacturer Length of cable AE8 Manufacturer Length of cable AE9 Manufacturer Length of cable AE10

/

/

/

Model CCB0046A10C1 HUIZHOU JUWEI ELECTRONICS CO.,LTD Model CCB0049A10C1 HUIZHOU JUWEI ELECTRONICS CO.,LTD Model CCB0049A10C4 Manufacturer Length of cable Dongguan MeiHao Electronic Technology Co., Ltd.

/

*AE ID: is used to identify the test sample in the lab internally. Note: The USB cables are shielded. Copyright. All rights reserved by CTTL. 3.4. EUT set-ups EUT set-up No. Combination of EUT and AE No.I19Z61162-EMC01 Page 8 of 27 Remarks Set.1 Set.2 Set.3 Set.4 EUT1+ AE1+ AE2+ AE5/AE6 + AE7/AE8/AE9/AE10 Charger + FM EUT1+ AE1+ AE3+ AE5/AE6 EUT1+ AE1+ AE4+ AE5/AE6 EUT1+ AE1+ AE5/AE6 Charger Charger USB mode Note: LTE / UMTS / GSM mobile phone 5033E manufactured by TCL Communication Ltd. is a variant model based on 5033A for conformance test. According to the declaration of changes, the following items are tested on Set.1 and Set.4. Mode or Feature EUT set-up No Test Item Charger + FM USB Mode Set.1 Set.4 Radiated Emission Radiated Emission Other results are inherited from the initial model. The report number of initial model is I18Z60562-EMC01. Copyright. All rights reserved by CTTL. 4. Reference Documents No.I19Z61162-EMC01 Page 9 of 27 4.1. Reference Documents for testing The following documents listed in this section are referred for testing. Reference Title Version FCC Part 15, Subpart B Radio frequency devices - Unintentional Radiators 2016 ANSI C63.4 American National Standard for 2014 Methods of Measurement of Radio-

Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz Note: The test methods have no deviation with standards. Copyright. All rights reserved by CTTL. No.I19Z61162-EMC01 Page 10 of 27 5. LABORATORY ENVIRONMENT Semi-anechoic chamber SAC-1 (23 meters17meters10meters) did not exceed following limits along the EMC testing:

Temperature Relative humidity Shielding effectiveness Electrical insulation Ground system resistance Normalised site attenuation (NSA) Min. = 15 , Max. = 35 Min. = 15 %, Max. = 75 %

0.014MHz - 1MHz, >60dB;

1MHz - 1000MHz, >90dB.

> 2 M

< 4

< 4 dB, 3m/10m distance, from 30 to 1000 MHz Site voltage standing-wave ratio (SVSWR) Between 0 and 6 dB, from 1GHz to 18GHz Uniformity of field strength Between 0 and 6 dB, from 80 to 3000 MHz Shielded room did not exceed following limits along the EMC testing:

Temperature Relative humidity Shielding effectiveness Electrical insulation Ground system resistance Min. = 15 , Max. = 35 Min. = 20 %, Max. = 75 %

0.014MHz-1MHz, >60dB;

1MHz1000MHz, >90dB.

> 2 M

< 4 Copyright. All rights reserved by CTTL. No.I19Z61162-EMC01 Page 11 of 27 6. SUMMARY OF TEST RESULTS Abbreviations used in this clause:

Verdict Column P NA F Pass Not applicable Fail Items Test Name Clause in FCC rules Section in this report Verdict Radiated Emission Conducted Emission 1 2 15.109(a) 15.107(a) B.1 B.2 P P Test Location CTTL(huayuan North Road) CTTL(huayuan North Road) Copyright. All rights reserved by CTTL. 7. Test Equipments Utilized No.I19Z61162-EMC01 Page 12 of 27 CAL DUE CALIBRA DATE TION INTERVA L 1 year 1 year NO. Description TYPE SERIES NUMBER MANUFACTURE Test Receiver Test Receiver Universal Radio ESU26 ESCI 7 100235 100344 R&S R&S 2020-03-01 2020-02-14 Communication CMW500 116588 R&S 2019-12-26 1 year Tester Universal Radio Communication CMW500 150344 R&S 2019-12-27 1 year Tester LISN ENV216 Signal Power SMBV100A 101200 260613 R&S R&S 2020-03-14 2019-12-27 EMI Antenna VULB 9163 9163-483 Schwarzbeck 2019-08-21 EMI Antenna 3115 6914 ETS-Lindgren 2020-01-03 PC Printer M4000e-17 M706GWXD P1606dn VNC3L52122 DELL HP N/A N/A 1 year 1 year 1 year 1 year N/A N/A 1 2 4 5 6 7 8 9 Test Item Test Software and Version Software Vendor Radiated Continuous Emission Conducted Emission EMC32 V9.01 EMC32 V8.52.0 R&S R&S Copyright. All rights reserved by CTTL. No.I19Z61162-EMC01 Page 13 of 27 ANNEX A: MEASUREMENT RESULTS A.1 Radiated Emission Reference FCC: CFR Part 15.109(a). A.1.1 Method of measurement The field strength of radiated emissions from the unintentional radiator (USB mode of MS and charging mode of MS) at distances of 10 meters(for 30MHz-1GHz) and 3 meters (for above 1GHz) is tested. Tested in accordance with the procedures of ANSI C63.4 2014, section 8.3. The EUT was placed on a non-conductive table. The measurement antenna was placed at a distance of 3/10 meters from the EUT. During the tests, the antenna height and the EUT azimuth were varied in order to identify the maximum level of emissions from the EUT. This maximization process was repeated with the EUT positioned in each of its three orthogonal orientations. A.1.2 EUT Operating Mode The MS is operating in the USB mode and charging mode. During the test MS is connected to a PC via a USB cable in the case of USB mode and is connected to a charger in the case of charging mode. The model of the PC is DELL OPTIPLEX 380, and the serial number of the PC is 2X1YV2X. The software is used to let the PC keep on copying data to MS, reading and erasing the data after copy action was finished. NoteI/O informationPrinter USB, Mouse PS/2, Keyboard USB. A.1.3 Measurement Limit Frequency range

(MHz) 30-88 88-216 216-960 960-1000

>1000 Field strength limit (V/m) Quasi-peak Average Peak 100 150 200 500 500 5000 Note: the above limit is for 3 meters test distance. 10 meters limit is got by converting. A.1.4 Test Condition Frequency range (MHz) RBW/VBW Sweep Time (s) Detector 30-1000 Above 1000 120kHz (IF Bandwidth) 1MHz/1MHz 5 15 Peak/Quasi-peak Peak, Average Copyright. All rights reserved by CTTL. A.1.5 Measurement Results No.I19Z61162-EMC01 Page 14 of 27 A "reference path loss" is established and the ARpl is the attenuation of reference path loss. It includes the antenna factor of receive antenna and the path loss. The measurement results are obtained as described below:

Result = PMea + ARpl = PMea + GA + GPL Where GA: Antenna factor of receive antenna GPL: Path Loss PMea: Measurement result on receiver. Measurement uncertainty (worst case): U = 4.3 dB, k=2. Measurement results for Set.1:

Charging Mode/Average detector Frequency

(MHz) 17956.367 17983.000 17835.667 17943.333 17831.133 17963.733 Measurement Result

(dBV/m) 43.7 43.7 43.7 43.6 43.5 43.5 Charging Mode/Peak detector Measurement Frequency

(MHz) 17680.400 17869.667 17406.700 17643.000 17949.000 17376.667 Result

(dBV/m) 55.3 54.5 54.3 54.2 54.1 54.1 Cable loss

(dB)

-5.4

-5.4

-5.7

-5.4

-5.7

-5.4 Cable loss

(dB)

-6.9

-5.7

-5.9

-6.9

-5.4

-6.5 Antenna Factor

(dB/m) 43.4 33.8 43.4 43.4 43.4 43.4 Antenna Factor

(dB/m) 43.4 33.8 40.1 43.4 43.4 40.1 Receiver Reading

(dBV) 5.716 15.316 6.038 5.616 5.838 5.516 Receiver Reading

(dBV) 18.802 26.438 20.125 17.702 16.116 20.496 Antenna Pol.

(H/V) H H V H H H Antenna Pol.

(H/V) H H V H H H Copyright. All rights reserved by CTTL. Measurement results for Set.2:

Charging Mode/Average detector Frequency

(MHz) 17416.050 17903.100 17371.000 17459.400 17975.350 17869.100 Measurement Result

(dBV/m) 38.7 38.6 38.4 38.4 38.4 38.4 Charging Mode/Peak detector Measurement Frequency

(MHz) 17757.750 17422.000 17881.000 17462.800 17914.150 17427.950 Result

(dBV/m) 49.1 49.0 49.0 49.0 48.9 48.8 No.I19Z61162-EMC01 Page 15 of 27 Cable loss

(dB)

-19.2

-18.5

-19.5

-19.2

-17.7

-18.5 Cable loss

(dB)

-18.5

-19.2

-18.5

-19.2

-18.5

-19.2 Antenna Factor

(dB/m) 41.5 45.6 41.5 41.5 45.6 45.6 Antenna Factor

(dB/m) 45.6 41.5 45.6 41.5 45.6 41.5 Receiver Reading

(dBV) 16.400 11.500 16.400 16.100 10.500 11.300 Receiver Reading

(dBV) 22.000 26.700 21.900 26.700 21.800 26.500 Antenna Pol.

(H/V) H H V H H H Antenna Pol.

(H/V) H H V H H H Copyright. All rights reserved by CTTL. Measurement results for Set.3:

Charging Mode/Average detector Frequency

(MHz) 17763.700 17897.150 17908.200 17906.500 17282.600 17893.750 Measurement Result

(dBV/m) 38.5 38.5 38.4 38.3 38.3 38.2 Charging Mode/ Peak detector Measurement Frequency

(MHz) 17858.050 17227.350 17869.950 17381.200 17832.550 17897.150 Result

(dBV/m) 48.9 48.8 48.7 48.7 48.7 48.6 No.I19Z61162-EMC01 Page 16 of 27 Cable loss

(dB)

-18.5

-18.5

-18.5

-18.5

-19.5

-18.5 Cable loss

(dB)

-18.5

-19.5

-18.5

-19.5

-18.5

-18.5 Antenna Factor

(dB/m) 45.6 45.6 45.6 45.6 41.5 45.6 Antenna Factor

(dB/m) 45.6 41.5 45.6 41.5 45.6 45.6 Receiver Reading

(dBV) 11.400 11.400 11.300 11.200 16.300 11.100 Receiver Reading

(dBV) 21.800 26.800 21.600 26.700 21.600 21.500 Antenna Pol.

(H/V) H H V H H H Antenna Pol.

(H/V) H H V H H H Copyright. All rights reserved by CTTL. Measurement results for Set.4:

USB Mode/Average detector Frequency

(MHz) 4851.633 4852.200 17898.000 17925.767 17987.533 17952.967 Measurement Result

(dBV/m) 47.6 46.5 34.8 34.8 34.6 34.6 USB Mode/ Peak detector Frequency

(MHz) 4852.200 4851.633 4852.767 4851.067 17823.200 17947.867 Measurement Result

(dBV/m) 51.6 51.5 50.7 50.6 47.9 47.4 No.I19Z61162-EMC01 Page 17 of 27 Cable loss

(dB)

-17.3

-17.3

-5.7

-5.4

-5.4

-5.4 Cable loss

(dB)

-17.3

-17.3

-17.3

-17.3

-5.7

-5.4 Antenna Factor

(dB/m) 32.3 33.8 43.4 43.4 43.4 43.4 Antenna Factor

(dB/m) 32.3 33.8 32.3 32.3 43.4 43.4 Receiver Reading

(dBV) 32.628 30.028

-2.862

-3.184

-3.384

-3.384 Receiver Reading

(dBV) 36.628 35.028 35.728 35.628 10.238 9.416 Antenna Pol.

(H/V) H H V H H H Antenna Pol.

(H/V) H H V H H H Note: The measurement results of Set.1, Set.2, Set.3 and Set.4 showed here are worst cases of the combinations of different USB cables and headsets. Copyright. All rights reserved by CTTL. Charging Mode, Set.1 No.I19Z61162-EMC01 Page 18 of 27 Fig A.1 Radiated Emission from 30MHz to 1GHz Final_Result Frequency QuasiPeak Limit Margin Meas. Bandwidth Height Pol Azimuth

(MHz)

(dBV/m)

(dBV/m)

(dB) Time

(kHz)

(cm)

(deg)

(ms) 34.910000 10.13 30.00 19.87 1000.0 120.000 400.0 V 39.354000 13.18 30.00 16.82 1000.0 120.000 400.0 V 41.742000 14.64 30.00 15.36 1000.0 120.000 217.0 V 114.0 202.0 76.0 51.534000 12.73 30.00 17.27 1000.0 120.000 125.0 V 151.0 102.348000 200.240000 8.51 8.20 33.50 25.01 1000.0 120.000 101.0 V 33.50 25.32 1000.0 120.000 400.0 V 30.0

-4.0 Copyright. All rights reserved by CTTL. 5 10 15 20 25 30 35 40 4530M 5060 80100M200300400500 8001GLevel in dBV/Frequency in HzFull SpectrumFCC PART15_QP_10m No.I19Z61162-EMC01 Page 19 of 27 Fig A.2 Radiated Emission from 1GHz to 18GHz Copyright. All rights reserved by CTTL. 10 20 30 40 50 60 70 801G2G3G4G5G6 8 10G18GLevel in dBV/Frequency in HzFull SpectrumFCC PART 15 _PKFCC PART 15_AVG Charging Mode, Set.2 No.I19Z61162-EMC01 Page 20 of 27 Fig A.3 Radiated Emission from 30MHz to 1GHz Final Result 1 Frequency QuasiPeak Limit Margin Meas. Time Bandwidth Height Pol Azimuth

(MHz)

(dBV/m)

(dBV/m)

(dB)

(ms)

(kHz)

(cm)

(deg) 50.061000 18.01 30.00 11.99 1000.0 120.000 111.0 V 30.0 Fig A.4 Radiated Emission from 1GHz to 18GHz Copyright. All rights reserved by CTTL. 0 5 10 15 20 25 30 35 40 4530M 5060 80100M200300400500 8001GLevel in dBV/mFrequency in HzFull SpectrumFCC PART15_QP_10m10 20 30 40 50 60 70 801G2G3G4G5G6 8 10G18GLevel in dBV/mFrequency in HzFull SpectrumFCC PART 15 _PKFCC PART 15_AVG Charging Mode, Set.3 No.I19Z61162-EMC01 Page 21 of 27 Fig A.5 Radiated Emission from 30MHz to 1GHz Final Result 1 Frequency QuasiPeak Limit Margin Meas. Time Bandwidth Height Pol Azimuth

(MHz)

(dBV/m)

(dBV/m)

(dB)

(ms)

(kHz)

(cm) 49.576000 18.50 30.00 11.50 1000.0 120.000 125.0 52.532000 16.96 30.00 13.04 1000.0 120.000 100.0

(deg) 30.0 195.0 V V Fig A.6 Radiated Emission from 1GHz to 18GHz Copyright. All rights reserved by CTTL. 0 5 10 15 20 25 30 35 40 4530M 5060 80100M200300400500 8001GLevel in dBV/mFrequency in HzFull SpectrumFCC PART15_QP_10m10 20 30 40 50 60 70 801G2G3G4G5G6 8 10G18GLevel in dBV/mFrequency in HzFull SpectrumFCC PART 15 _PKFCC PART 15_AVG USB Mode, Set.4 No.I19Z61162-EMC01 Page 22 of 27 Fig A.7 Radiated Emission from 30MHz to 1GHz Fig A.8 Radiated Emission from 1GHz to 18GHz Copyright. All rights reserved by CTTL. 0 5 10 15 20 25 30 35 40 45 50 55 6030M 5060 80100M200300400500 8001GLevel in dBV/Frequency in HzFull SpectrumFCC PART15_QP_10m10 20 30 40 50 60 70 801G2G3G4G5G6 8 10G18GLevel in dBV/Frequency in HzFull SpectrumFCC PART 15 _PKFCC PART 15_AVG No.I19Z61162-EMC01 Page 23 of 27 A.2 Conducted Emission Reference FCC: CFR Part 15.107(a). A.2.1 Method of measurement For equipment that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits. Tested in accordance with the procedures of ANSI C63.4 2014, section 7.3. A.2.2 EUT Operating Mode The MS is operating in the USB mode and charging mode. During the test MS is connected to a PC via a USB cable in the case of USB mode and is connected to a charger in the case of charging mode. The model of the PC is DELL OPTIPLEX 380, and the serial number of the PC is 2X1YV2X. The software is used to let the PC keep on copying data to MS, reading and erasing the data after copy action was finished. NoteI/O informationPrinter USB, Mouse PS/2, Keyboard USB. A.2.3 Measurement Limit Frequency of emission (MHz) Conducted limit (dBV) Quasi-peak 66 to 56*

56 60 0.15-0.5 0.5-5 5-30

*Decreases with the logarithm of the frequency A.2.4 Test Condition in charging mode VoltageV 120 FrequencyHz 60 RBW/IF bandwidth Sweep Time(s) 9kHz 1 Average 56 to 46*

46 50 Copyright. All rights reserved by CTTL. A.2.5 Measurement Results Measurement uncertainty: U= 2.9 dB, k=2. Charging Mode, Set.1 No.I19Z61162-EMC01 Page 24 of 27 Fig A.9 Conducted Emission Final Result 1 Frequency QuasiPeak Meas. Bandwidth Line Corr. Margin Limit

(MHz)

(dBV) 0.195000 0.735000 1.131000 1.968000 3.097500 3.844500 40.7 36.6 38.4 42.1 43.5 41.5 Time

(ms) 2000.0 2000.0 2000.0 2000.0 2000.0 2000.0

(kHz)

(dB)

(dB)

(dBV) 9.000 9.000 9.000 9.000 9.000 9.000 L1 L1 L1 L1 L1 L1 19.8 19.8 19.6 19.7 19.7 19.6 23.1 19.4 17.6 13.9 12.5 14.5 63.8 56.0 56.0 56.0 56.0 56.0 Final Result 2 Frequency Average Meas. Bandwidth Line Corr. Margin Limit

(MHz)

(dBV) 0.636000 1.108500 1.869000 2.688000 3.628500 6.171000 25.3 27.8 31.1 33.0 31.9 28.5 Time

(ms) 2000.0 2000.0 2000.0 2000.0 2000.0 2000.0

(kHz)

(dB)

(dB)

(dBV) 9.000 9.000 9.000 9.000 9.000 9.000 L1 L1 L1 L1 L1 L1 19.8 19.6 19.7 19.7 19.6 19.7 20.7 18.2 14.9 13.0 14.1 21.5 46.0 46.0 46.0 46.0 46.0 50.0 Note: The measurement results showed here are worst cases of the combinations of different USB cables. Copyright. All rights reserved by CTTL. 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70150k 300400500 8001M2M3M4M5M6 810M20M30MLevel in dBVFrequency in Hz Charging Mode, Set.2 No.I19Z61162-EMC01 Page 25 of 27 Fig A.10 Conducted Emission Final Result 1 Frequency QuasiPeak Meas. Bandwidth Line Corr. Margin Limit

(MHz)

(dBV) 0.393000 0.672000 1.180500 2.004000 3.331500 4.110000 42.5 44.7 39.5 46.3 45.0 46.0 Time

(ms) 2000.0 2000.0 2000.0 2000.0 2000.0 2000.0

(kHz) 9.000 9.000 9.000 9.000 9.000 9.000

(dB)

(dB)

(dBV) L1 L1 L1 L1 L1 L1 19.9 19.8 19.6 19.7 19.7 19.6 15.5 11.3 16.5 9.7 11.0 10.0 58.0 56.0 56.0 56.0 56.0 56.0 Final Result 2 Frequency Average Meas. Bandwidth Line Corr. Margin Limit

(MHz)

(dBV) 0.339000 0.730500 1.176000 2.067000 3.484500 4.272000 38.5 35.0 37.3 37.5 32.7 37.0 Time

(ms) 2000.0 2000.0 2000.0 2000.0 2000.0 2000.0

(kHz)

(dB)

(dB)

(dBV) 9.000 9.000 9.000 9.000 9.000 9.000 L1 L1 L1 L1 L1 L1 19.8 19.8 19.6 19.7 19.7 19.6 10.7 11.0 8.7 8.5 13.3 9.0 49.2 46.0 46.0 46.0 46.0 46.0 Note: The measurement results showed here are worst cases of the combinations of different USB cables. Copyright. All rights reserved by CTTL. 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70150k 300400500 8001M2M3M4M5M6 810M20M30MLevel in dBVFrequency in Hz Charging Mode, Set.3 No.I19Z61162-EMC01 Page 26 of 27 Fig A.11 Conducted Emission Final Result 1 Frequency QuasiPeak Meas. Bandwidth Line Corr. Margin Limit

(MHz)

(dBV) 0.424500 0.703500 1.216500 1.729500 2.796000 3.655500 40.1 40.1 44.1 44.9 43.3 41.5 Time

(ms) 2000.0 2000.0 2000.0 2000.0 2000.0 2000.0

(kHz)

(dB)

(dB)

(dBV) 9.000 9.000 9.000 9.000 9.000 9.000 L1 L1 L1 L1 L1 L1 19.9 19.8 19.6 19.7 19.7 19.6 17.2 15.9 11.9 11.1 12.7 14.5 57.4 56.0 56.0 56.0 56.0 56.0 Final Result 2 Frequency Average Meas. Bandwidth Line Corr. Margin Limit

(MHz)

(dBV) Time

(kHz)

(dB)

(dB)

(dBV) 0.415500 0.703500 1.212000 1.797000 2.674500 3.655500 28.7 29.3 34.1 31.9 32.9 28.3

(ms) 2000.0 2000.0 2000.0 2000.0 2000.0 2000.0 9.000 9.000 9.000 9.000 9.000 9.000 L1 L1 L1 L1 L1 L1 19.9 19.8 19.6 19.7 19.7 19.6 18.9 16.7 11.9 14.1 13.1 17.7 47.5 46.0 46.0 46.0 46.0 46.0 Note: The measurement results showed here are worst cases of the combinations of different USB cables. Copyright. All rights reserved by CTTL. 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70150k 300400500 8001M2M3M4M5M6 810M20M30MLevel in dBVFrequency in Hz USB Mode, Set.4 No.I19Z61162-EMC01 Page 27 of 27 Final Result 1 Frequency QuasiPeak Meas. Bandwidth Line Corr. Margin Limit

(MHz)

(dBV) 0.204000 0.978000 3.520500 4.398000 6.598500 24.009000 45.1 32.1 30.8 33.7 41.8 38.3 Time

(ms) 2000.0 2000.0 2000.0 2000.0 2000.0 2000.0

(kHz) 9.000 9.000 9.000 9.000 9.000 9.000

(dB)

(dB)

(dBV) L1 N N N N N 19.8 19.7 19.7 19.7 19.8 20.2 18.3 23.9 25.2 22.3 18.2 21.7 63.4 56.0 56.0 56.0 60.0 60.0 Final Result 2 Frequency Average Meas. Bandwidth Line Corr. Margin Limit

(MHz)

(dBV) 0.168000 0.267000 3.381000 4.600500 6.598500 24.009000 44.7 34.4 21.7 25.4 38.9 38.4 Time

(ms) 2000.0 2000.0 2000.0 2000.0 2000.0 2000.0

(kHz)

(dB)

(dB)

(dBV) 9.000 9.000 9.000 9.000 9.000 9.000 L1 L1 N N N N 19.8 19.8 19.7 19.7 19.8 20.2 10.4 16.8 24.3 20.6 11.1 11.6 55.1 51.2 46.0 46.0 50.0 50.0 Note: The measurement results showed here are worst cases of the combinations of different USB cables.

***END OF REPORT***

Copyright. All rights reserved by CTTL. 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70150k 300400500 8001M2M3M4M5M6 810M20M30MLevel in dBVFrequency in Hz

201 9-06-11 Fed Offi Equ 734 Colu deral Comm fice of Engin uipment Aut 45 Oakland M umbia, Mar munications C neering and thorization Mills Road ryland 2104 46 Commission n d Technolog gy Division Sub bject: Perma anent Confid dentiality re equest for F FCC ID: 2A CCJH089 To W Purs con Whom It M suant to sec fidential tre n, May Concern 7 and 0.459 ctions 0.457 eatment of th he followin of CFR 47, ng informati the applica ion accompa ant requests anying this permanent application n:

-

BOOM list The rele appl e above mat eased to the licant and p erials conta public. The provide unju ain trade sec e public disc ustified bene crets and pro closure of th efits to its c nformation n oprietary in hese matter s might be h

. competitors not customa harmful to t arily the You urs Sincerel ly, Zhiz Prod TCL G zhou GONG duct Certifi cation Man nication Lt L Commun nager d. TCL Communic 7/F, Block zhong Shan h z henzhen, Gua sh Tel:0086-755-366 cation Ltd. F4, TCL Int Yuan Road, angdong, P.R 611722 Fax: 008 ernational E Nanshan Di

. China 5180 86-75536612000-

City, strict, 52

-81722 htt p://tclcom.tcl.co om

CTT TL-Telecomm munication T Technology y Labs, Acad demy of Tel ecommunic cation Resea arch, T is authori merican Certi ized to act ification Bo on our beh ody, Inc. (A half, until o ACB). otherwise no otified, for application ns to certify that efits, pursua ther, no par ial of federa t we are not ant to Sectio rty, as defin al benefits, subject to d on 5301 of ed in 47 CF that include denial of fed the Anti-Dr FR1.2002 (b es FCC ben deral benefi rug Abuse A b) to the app nefits. fits, which in Act of 1988 plication is s ncludes FCC C 62. 8, U.S.C. 86 subject to e 2018-04-2 27 Federal Co Authoriza 7345 Oakl Columbia ons Commi ommunicatio luation Div ation & Eval land Mills R Road 6

, MD 21046 ission, vision, Certificatio d American ttier Avenu 6731 Whi 0 Suite C11 McLean, V VA 22101 on Body, In ue nc. Whom It M May Concern n:

ank you. gards, G zhou GONG duct Certifi cation Man nication Lt L Commun nager d. Dat To:

And To W MIIT Am We ben Furt deni Tha Reg Zhiz Prod TCL TCL Communic 7/F, Block zhong Shan h z henzhen, Gua sh Tel:0086-755-366 cation Ltd. F4, TCL Int Yuan Road, angdong, P.R 611722 Fax: 008 ernational E Nanshan Di

. China 5180 86-75536612000-

City, strict, 52

-81722 htt p://tclcom.tcl.co om

5F, C building, No. 232, Liang Jing Road ZhangJiang High-Tech Park, Pudong Area Shanghai, P.R. China. 201203 TEL: +86(0)21 61460666 FAX: +86(0)21 61460602 Declaration of changes from 5033A to 5033M SOFTWARE MODIFICATIONS:

Protocol Stack changes: No MMS/STK/USAT/USIM changes: No DM/SUPL/VT/FUMO/SWP/HCI: No Other changes detailed:

HARDWARE MODIFICATIONS:

Antenn a NO GSM850 NO GSM900 NO GSM1800 NO GSM1900 UMTS2100 NO UMTS1900 NO UMTS1700 NO NO UMTS900 NO UMTS850 NO LTE 1 NO LTE 2 NO LTE 3 NO LTE 4 NO LTE 5 NO LTE 7 NO LTE 8 NO LTE 12 NO LTE 13 NO LTE 17 NO LTE 28 NO Bluetooth NO WiFi NA NFC Band changes: No PCB Layout changes: NO Main components changes:

Transceive Base r Band NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NA FM changes: No Other components changes:

Other changes detailed: memory changed from 8+1 to 16+1, and the chipset is pin to pin compatible. Power Amplifier NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA Duplex er NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA Tx SAW Filter NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA Rx SAW Filter NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA ASM NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA LCD/ Speaker/ Camera/ Vibrator changes: No MECHANICAL MODIFICATIONS:

Use new metal front/back cover or keypad: No Mechanical shell changes:

Whole size of EUT: No Distance of Ear reference point to bottom of handset: No Other trinkets to change the surface of handset: No Other changes detailed:

APPROVED BY:

Project Manager:

Signature:

Date: 2019-5-9