USERS GUIDE Introduction Initial Setup Connecting a Bluetooth Source Using your STA-200 as a SKAA Receiver Using the Line-level Analog Audio Input Using the AUX Input Using your STA-200 Together in a SKAA Network The SKAA cmd App 2 3 5 7 9 9 10 12 012518 1/12 STA-200 USERS GUIDE Introduction Power LED Bright Orange: On Dim Orange: Sleep Bluetooth LED See Page 6 for behaviour SKAA Indicator LED See Page 8 for behaviour Gear Button Click to switch modes Hold to power on/off Bluetooth Button See Page 6 for behaviour SKAA Bond Button See Page 8 for behaviour AUX LED See Page 9 for behaviour Infrared Receiver Sensor for IR remote IR Audio Input Volume Down Button Volume Up Button Relay LED See Page 10-11 for behaviour AUX Input Jack See Page 9 for behaviour 012518 2/12 STA-200 USERS GUIDE Initial Setup The STA-200 supports both active and passive speakers. If you are connecting active speakers (i.e. if your speakers use power cables) connect them to the output labeled "Line out". Power On O R L Line in L Line out L R R
+
_ 100-240~50/60Hz 200 Watts Max Power Speaker Output (4Ohm) If you are connecting passive speakers (i.e. if your speakers are powered solely by the connection to your STA-200) connect them to the output labeled "Speaker Output". Power On O R L Line in L Line out L R R
+
_ 100-240~50/60Hz 200 Watts Max Power Speaker Output (4Ohm) 012518 3/12 STA-200 USERS GUIDE Initial Setup Before attempting to use any buttons on the front plate, ensure that the power switch on the back of your STA-200 is flipped to the "On" position. Next, hold the Gear button for two seconds to power on the unit. Once the power LED is illuminated, click the Gear button to cycle through modes. 012518 4/12 STA-200 USERS GUIDE Connecting a Bluetooth Source Cycle to Bluetooth mode by clicking the Gear button. When in Bluetooth mode, the Bluetooth LED will be illuminated. IR Audio Input Enter pairing mode on the Bluetooth device you want to connect to the JE-0495 and select the STA-200 from the discoverable devices list. The below diagram represents the Bluetooth behaviour of the STA-200 012518 5/12 STA-200 USERS GUIDE Connecting a Bluetooth Source Initialization Initialization begins when the user enters BT Mode or BT Relay Mode from any other mode, by clicking the Gear button. Initialization also begins if the user powers on STA-200 in either BT Mode or BT Relay mode. Pairing List The Paired List contains up to eight of the most recent hosts, which have successfully paired and connected with STA-200. Button Clicking the button toggles between the Attempt Connection state and the Pairing state. From the Connected state, a two-second press and hold of the button will force the STA-200 to drop the connection to its currently connected device and enter the Pairing state. A ten-second press
& hold of the button will clear the Paired List and enter the Paring state. Timeouts From Initialization, the STA-200 attempts to connect to the most recently connected host for ten seconds. After ten seconds, if a successful connection has not been established, Nadja will enter the Pairing state. If the connected host goes out of range, the STA-200 attempts to reconnect to that host for 60 seconds. After 60 seconds, if a successful connection has not been established, the STA-200 will enter the Pairing state. 012518 6/12 STA-200 USERS GUIDE Using your STA-200 as a SKAA Receiver The STA-200 can be used as a SKAA receiver when in SKAA mode. A SKAA receiver receives wireless audio from any SKAA transmitter. For a complete list of SKAA transmitters visit www.skaastore.com/products/
transmitters/
Ensure your SKAA transmitter is powered, and that your host device is playing audio. For example, if you are using a smart phone, make sure that your SKAA transmitter is plugged into your smart phone and that music is playing. Click the Gear button to cycle through modes, until you enter SKAA mode. The SKAA Indicator LED will will illuminate once you have entered SKAA mode. When in SKAA mode, your STA-200 should automatically begin playing the audio received over SKAA, through the speakers you have connected. IR Audio Input One SKAA transmitter can serve up to four SKAA receivers. SKAA Transmitter SKAA
(Up to 50 m) 012518 7/12 STA-200 USERS GUIDE Using your STA-200 as a SKAA Receiver Indicator Bond Button IR Audio Input 012518 8/12 STA-200 USERS GUIDE Using the Line-level Analog Audio Input Power On O R L Line in L Line out L R R
+
_ 100-240~50/60Hz 200 Watts Max Power Speaker Output (4Ohm) Audio Source Connect your line level input to the input labeled "Line in" on the back of your JE-0495. Click the Gear button to cycle to AUX mode. When in AUX mode, the yellow LED above AUX will illuminate. Make sure no cables are plugged into the AUX jack located on the front of the JE-0495. If you want to play audio from the "Line In"
input on the back, having something plugged into the Audio Input jack on the front will override the line in audio. IR Audio Input Using the AUX Audio Input Click the Gear button to cycle to AUX mode. When in AUX mode, the yellow LED above AUX will illuminate. IR Audio Input Plug your audio device into the AUX jack located on the front of the STA-200. 012518 9/12 STA-200 USERS GUIDE Using your STA-200 Together in a SKAA Network Both Bluetooth and AUX modes come equipped with an optional Relay mode. When in either BT Relay or AUX Relay modes, the white Relay LED will be illuminated in addition to the Bluetooth or AUX LEDS. When in one of the Relay modes, your Bluetooth or AUX signal is relayed over SKAA to up to four more SKAA receivers. Bluetooth Relay IR Audio Input SKAA Mode SKAA Mode SKAA Mode BT-Relay Mode Bluetooth
(Up to 10 m) SKAA
(Up to 50 m) SKAA Mode 012518 10/12 STA-200 USERS GUIDE Using your STA-200 Together in a SKAA Network AUX Relay IR Audio Input SKAA Mode SKAA Mode SKAA Mode AUX-Relay Mode AUX Cable SKAA
(Up to 50 m) SKAA Mode 012518 11/12 STA-200 USERS GUIDE SKAA cmd SKAA cmd is an optional App available for iPhone, iPad, iPod, Android, Mac and PC. You can find it on our website www.skaa.com/tlc/ or in the iOS App store and Google Play. SKAA cmd is great for getting the most out of your STA-200. To use SKAA cmd throw your STA-200 into SKAA mode, download the app, insert a SKAA transmitter and check out all of the customizable features of SKAA. 012518 12/12 FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.