FCC ID: 2ALB6-CTRLBLEL1 Bluetooth Remote Control

1. Caster L1 Remote Control 2. Turn On Caster L1 Caster L1 remote control arrives with a 2 AAA batteries blister inside a polybag. To turn on your Caster L1 remote control, please follow the instructions below. Product Manual CASTER L1 BLE remote control T4HS1 13 32kC 1. Turn ON your TV and your Set Top Box. 2. Remove your Caster L1 remote control and its batteries from the plastic bag. 3. Remove the remotes battery lid. 4. Place the batteries on the Caster L1 remote control as indicated in the image above and replace the battery lid. 5. After inserting the batteries, wait a few seconds and the Caster L1 remote will be ready to operate the Set-Top-Box. FCC Compliance Statements CAUTION 1. Risk of explosion if the battery is replaced by an incorrect type;

2. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;

3. Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;

4. A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. Temperature range: 0 - 50C Altitude: up to 3000 feet MANUFACTURER Tech4home, Lda Rua de Fund es, n 151 3 00-121 S.o o da Madeira, Portugal NAMEPLATE LOCATED ON THE BATTERY COMPARTMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televison reception, which can be determinated by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:

. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation expuser limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

APPENDIX C Label Artwork Each equipment covered in the certification for equipment authorization shall bear a label listing as the following:

1) An FCC ID, which should be printed in the following format with legible lettering. Eight point type is acceptable. FCC ID

in capital letters on a single line. FCC ID: 2ALB6-CTRLBLEL1 2ALB6 -

your grantee code as assigned by the FCC (may be three or five). CTRLBLEL1

up to 14 alphanumeric characters you select. Dash or hyphen (-) may be used. No spaces are allowed. 2) Label artwork Note 1: The label shall not be a stick-on paper label. The label on these products shall be permanently affixed to the product and shall be readily visible to the purchaser at the time of purchase. Permanently affixed means that the label is etched, engraved, stamped, silkscreened, indelibly printed, or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal, plastic, or other material fastened to the equipment by welding, riveting, or a permanent adhesive. The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable. Note 2: Label dimensions in millimeters. Note 3: Above labelling example is for reference only, may have some differences with to actual product.

Date (21/09/2022) Tech4home, Lda TUV SUD BABT UNLIMITED Octagon House, Concorde Way, Segensworth North, Fareham, Hampshire, PO15 5RL United Kingdom Confidentiality Request FCC ID: 2ALB6-CTRLBLEL1 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, Tech4home, Lda hereby requests permanent confidential treatment of information accompanying this application as outlined below:

Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation]

Tech4home, Lda also hereby requests short-term confidential treatment of information accompanying this application as outlined below for a period of 180 days:

Internal Photos External Photos User Manual Test Set-up Photographs The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Company Officer:

Miguel Valente Telephone Number:

+351 256 001 974 Email:

qc@tech4home.pt

Tech4home, Lda TUV SUD BABT UNLIMITED Octagon House, Concorde Way, Segensworth North, Fareham, Hampshire, PO15 5RL United Kingdom Date: September 20, 2022 Total Page (Cover Included):1 Quo#:

To:

Attention:

From:

Fax No:

Project No.:

Subject:

Declaration letter We: Tech4home, Lda Address: Rua de Fundoes 151, 3700-121 Sao Joao da Madeira, PORTUGAL Officially notify TV SD Certification and Testing (China) Co., Ltd. Shenzhen Branch that the

<<T4HS1906/32kC, T4HU2222/32kA, T4HU2223/32kA, T4HU2224/32kA, CTRLBLEL1, Caster L1 BLE (TL) RCU >> have the same technical construction including circuit diagram, PCB Layout, components and component layout, all electrical construction and mechanical construction, with <<

Bluetooth Remote Control >>, << T4HS1813/32kC >>. The difference lies only in <the outlook/color> of the different models.

<< Additional model >> T4HS1906/32kC, T4HU2222/32kA, T4HU2223/32kA, T4HU2224/32kA, CTRLBLEL1, Caster L1 BLE (TL) RCU

<< Main Model >>: T4HS1813/32kC

<<Product Name >>: Bluetooth Remote Control Applicant: Tech4home, Lda ___________

(Date 2022/09/20) (Miguel Valente, Quality and Purchasing Manager) file: declaration letter-template Page 1 of 1