all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 1.71 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Block Diagram | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | ID Label/Location Info | |||||||
1 | Operational Description | |||||||
1 | Test Setup Photos | |||||||
1 | Test Report |
1 | User Manual | Users Manual | 1.71 MiB |
Remote Alarm System Instructions for Use Copyright Notice Copyright 11/06/2010 TECNIPLAST S.p.A. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language without the prior written permission of TECNIPLAST S.p.A. Trademarks RAS is a trademark of TECNIPLAST S.p.A. Technical Support For technical support, call +39-0332-809711 or send an E- mail to service@tecniplast.it or tecnicom@tecniplast.it PREFACE I. Dear Customer, This manual is aimed at providing the user with all the information and safety standards required for the correct and safe installation, use and maintenance of the equipment you have purchased. Keep the manual in an easily accessible place, known by the Installer, the operator, the supervisor and the service technician who should carefully read it to have a clear understanding of the installation, use, and maintenance procedures as well as hazardous applications to avoid. This manual is an integral part of the equipment and should follow it, even in the event of a change of ownership, until final decommissioning. Should the manual get damaged or lost, a copy can be requested from TECNIPLAST. In order to receive technical assistance, spare parts or optional extras not required on order, contact TECNIPLAST and give the equipment serial number, version, and year of manufacture (see label on the equipment). The Operator, the Supervisor and the Service Technician must know all the standards reported in this manual before using the equipment or carrying out maintenance procedures. II. At TECNIPLAST both our production facilities and our end products reflect our commitment towards environmental policies in terms of:
COMPANY CONFORMITY TO ENVIRONMENTAL POLICIES compliance with the principles and contents of current laws and regulations concerning the environment;
reduction of the environmental impact deriving from our activities, maintaining the right balance between environmental, social and economic responsibilities;
on-going quest for innovative applications in order to reduce the environmental impact deriving from waste materials, energy consumption and to improve the use of natural resources and raw materials. preventive evaluation of the environmental impact of new plants and processes and improvement of existing ones using all possible and economically sustainable solutions to increase our environmental performances. incentivation and co-responsibility of employees towards this policy by means of adequate training use of effective tools to communicate principles and goals of such an environmental policy to our dealers during meetings and training courses;
defining during the design and development of new products the correct use and dismantling instructions to minimize environmental impact. i 1 2 3 4 5 6 7 Table of contents 2.1 2.2 1.4.1 1.4.2 1.4.3 1.4.4 INTRODUCTION .............................................................................................................................................. 4 1.1 MANUFACTURERS DETAILS ...................................................................................................................................... 4 TECHNICAL ASSISTANCE ............................................................................................................................................ 4 1.2 UNAUTHORISED MODIFICATIONS ............................................................................................................................. 4 1.3 1.4 TECHNICAL SPECIFICATIONS ..................................................................................................................................... 4 TX-WW MODULE ......................................................................................................................................... 4 TX-AMERICA ................................................................................................................................................. 5 CX/RX-WW ................................................................................................................................................... 5 CX/RX-AMERICA ........................................................................................................................................... 5 OPERATING ENVIRONMENTAL CONDITIONS ............................................................................................................ 6 1.5 COMPLIANCE TO EU DIRECTIVES .............................................................................................................................. 7 1.6 DECLARATION OF CONFORMITY ............................................................................................................................... 7 1.7 RESPONSIBILITY OF THE CUSTOMER ......................................................................................................................... 7 1.8 SPARE PARTS AND TECHNICAL ASSISTANCE ............................................................................................................. 7 1.9 1.10 UNAUTHORISED MODIFICATIONS ............................................................................................................................. 8 1.11 WASTE ELECTRIC AND ELECTRONIC EQUIPMENT ..................................................................................................... 8 1.12 DISPOSAL OF OTHER MATERIALS .............................................................................................................................. 8 SAFETY PRECAUTIONS .................................................................................................................................... 9 SAFETY NOTES ........................................................................................................................................................... 9 GENERAL PRECAUTIONS ........................................................................................................................................... 9 APPLICATIONS AND WORKING PRINCIPLE ................................................................................................... 10 3.1 HAZARDOUS AND INAPPROPRIATE APPLICATIONS................................................................................................. 10 3.2 MAIN FEATURES ...................................................................................................................................................... 11 TX TRANSMITTER ....................................................................................................................................... 11 3.2.1 3.2.2 RX AND CX .................................................................................................................................................. 11 HANDLING AND TRANSPORTATION ............................................................................................................. 12 DISPOSAL OF THE PACKAGING ................................................................................................................................ 12 HANDLING ............................................................................................................................................................... 12 INCOMING INSPECTION .......................................................................................................................................... 12 STORAGE ................................................................................................................................................................. 12 RAS SYSTEM INSTALLATION GUIDELINES ..................................................................................................... 13 RX AND CX ELECTRICAL CONNECTIONS................................................................................................................... 13 HOW TO MOUNT THE RX/CX ON THE WALL ........................................................................................................... 15 RX, CX AND TX CONNECTION .................................................................................................................................. 16 RAS SYSTEM RECEIVER (RX) SOFTWARE USER GUIDE .................................................................................. 18 6.1 MAIN MENU ............................................................................................................................................................ 18 6.2 UNIT MENU ............................................................................................................................................................. 19 ALARM FUNCTIONS ................................................................................................................................................. 20 6.3 PSTN DIALER FUNCTIONS ........................................................................................................................................ 21 6.4 SETTINGS FUNCTIONS ............................................................................................................................................. 22 6.5 HOURS AND DATE SETTING ....................................................................................................................... 22 UNIT SETTINGS ........................................................................................................................................................ 23 ALARM SETTING PAGE ............................................................................................................................... 24 PSTN DIALER SETTINGS .............................................................................................................................. 25 DIRECT OUTPUT ......................................................................................................................................... 27 PASSWORD SETTING .................................................................................................................................. 28 FIRMWARE .............................................................................................................................................................. 28 TIME-OUT EXIT ........................................................................................................................................................ 29 LANGUAGE SETTING PAGE ...................................................................................................................................... 29 RAS SYSTEM CENTRALISED RECEIVER(CX) SOFTWARE USER GUIDE ............................................................ 30 7.1 MAIN MENU ............................................................................................................................................................ 30 UNIT MENU ............................................................................................................................................................. 31 7.2 ALARM FUNTIONS ................................................................................................................................................... 32 7.3 7.4 PSTN DIALER FUNCTIONS ........................................................................................................................................ 33 6.6.1 6.6.2 6.6.3 6.6.4 4.1 4.2 4.3 4.4 6.7 6.8 6.9 5.1 5.2 5.3 6.5.1 6.6 2 8 7.5 7.6 7.7 7.8 7.9 8.1 8.2 7.5.1 7.6.1 7.6.2 7.6.3 7.6.4 SETTINGS FUNCTIONS ............................................................................................................................................. 33 HOURS AND DATE SETTING ....................................................................................................................... 34 UNIT SETTINGS ........................................................................................................................................................ 34 ALARM SETTING PAGE ............................................................................................................................... 35 PSTN DIALER SETTINGS .............................................................................................................................. 36 DIRECT OUTPUT ......................................................................................................................................... 37 PASSWORD SETTING .................................................................................................................................. 38 FIRMWARE .............................................................................................................................................................. 38 TIME-OUT EXIT ........................................................................................................................................................ 39 LANGUAGE SETTING PAGE ...................................................................................................................................... 39 ALARMS REPORTED BY THE SYSTEM ............................................................................................................ 40 ALARMS RAISED BY THE TRANSMITTER (TX) ........................................................................................................... 40 ALARMS RAISED BY THE RX ..................................................................................................................................... 40 3 1 INTRODUCTION 1.1 MANUFACTURERS DETAILS TECNIPLAST S.p.A. Via I Maggio, 6 21020 BUGUGGIATE (VA) ITALY Tel. Fax
+39 0332 809 711
+39 0332 458 315 www.tecniplast.it E-mail : tecnicom@tecniplast.it service@tecniplast.it TECNIPLAST S.p.A. reserves the right to modify the specifications to improve the product at any time. 1.2 TECHNICAL ASSISTANCE Requests for Technical Assistance should be addressed to TECNIPLAST or the authorized Dealer. 1.3 UNAUTHORISED MODIFICATIONS No modifications to the equipment or its components are to be made without written permission from TECNIPLAST. Unauthorised modifications could cause changes to the original functioning and consequently:
1. 2. All forms of warranty regarding the entire equipment will be null and void. If the equipment is used in a manner that is not specified by the manufacturer, the protection provided by the equipment may be impaired. 1.4 TECHNICAL SPECIFICATIONS 1.4.1 TX-WW MODULE Value Power supply Power consumption Operating frequency EMEA+AU+NZ module Operating frequency for China Operating frequency for Japan Installation frequency Radiated power for EMEA+AU+NZ+China module Radiated power for Japan Radio sensitivity Dimensions Operating temperature Protection rating Min 21,6V DC
+6dBm
+3dBm 0 C Typ 24V DC 20mA 434,4 MHz 431 MHz 429,825 MHz 433,2 MHz
+8dBm
+6dBm
-113dBm 5,2x11,5 cm IP20 Max 26,4V DC
+10dBm
+7dBm 40C 4 1.4.2 TX-AMERICA Value Power supply Power consumption Operating frequency for America Installation frequency Radiated power for America Radio sensitivity Dimensions Operating temperature Protection rating 1.4.3 CX/RX -WW Value Power supply Frequency Power supply model (UL:NO) Power consumption Relay dry contacts Operating frequency for EMEA+AU+NZ module Operating frequency for China module Operating frequency for Japan module Installation frequency Radiated power for EMEA+AU+NZ+Cina Radiated power for Japan Radio sensivity Dimensions Operating temperature Protection rating 1.4.4 CX/RX -AMERICA Value Power supply Frequency Power supply model (UL:NO) Power consumption Relay dry contacts Operating frequency for America module Installation frequency Radiated power for America Radio sensivity Dimensions Operating temperature Protection rating Min 21,6V DC
-6dBm 0 C Min 110V AC 50Hz
+6dBm
+3dBm 0 C Typ 24V DC 20mA 913 MHz 910 MHz
-3dBm
-113dBm 5,2x11,5 cm IP20 Typ Morsun LH10 10C0512-02 (10W) 0,1A 30Vcc 120Vac 2A 434,4 MHz 431 MHz 429,825 MHz 433,2 MHz
+8dBm
+6dBm
-113dBm 23x21,5 cm IP50 Min 110V AC 50Hz Typ
-6dBm 0 C Morsun LH10 10C0512-02 (10W) 0,1A 30Vcc 120Vac 2A 913 MHz 910 MHz
-3dBm
-113dBm 23x21,5 cm IP50 Max 26,4V DC
-2dBm 40 C Max 240V AC 60Hz
+10dBm
+7dBm 40 C Max 240V AC 60Hz
-2dBm 40 C 5 IMPORTANT: CHANGES AND MODIFICATIONS NOT APPROVED BY TECNIPLAST COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 6 1.5 OPERATING ENVIRONMENTAL CONDITIONS The equipment has been designed to perform under the following conditions:
Indoor use Altitude up to 2000m Maximum relative humidity 80% for temperatures up to 31C decreasing linearly to 50% relative humidity at Temperatures 5C to 40C 40C. Mains supply voltage fluctuations up to 10% of the nominal voltage Transient overvoltages typically present on the mains supply (OVERVOLTAGE CATEGORY II as per IEC 60364-
4-443) Pollution degree 2 1.6 COMPLIANCE TO EU DIRECTIVES DIRECTIVE 1999/05/EC R&TTE STANDARD EN/60950 - 1:2006 + A11:2009 STANDARD EN/300220 - 2 V2.3.1 STANDARD EN/301489 - 3 V1.4.1 TECNIPLAST S.p.A. reserves the right to modify the specifications to improve the product at any time. 1.7 DECLARATION OF CONFORMITY The equipment technical documentation includes the DECLARATION OF CONFORMITY in compliance with EU Equipmentry Directive 1999/05/EC R&TTE. 1.8 RESPONSIBILITY OF THE CUSTOMER Unless otherwise specified in the contract conditions, the Client shall supply:
Electrical supply complete with EARTH in the vicinity of the equipment. 1.9 SPARE PARTS AND TECHNICAL ASSISTANCE In order to conform to the terms and duration of the Warranty and to ensure perfect inter-changeability, only original TECNIPLAST spare parts are to be used. Requests for Technical Assistance should be addressed to TECNIPLAST or the authorized Dealer. 7 1.10 UNAUTHORISED MODIFICATIONS No modifications to the equipment or its components are to be made without written permission from TECNIPLAST. Unauthorised modifications could cause changes to the original functioning and consequently:
1. All forms of warranty regarding the entire equipment will be null and void. 2. If the equipment is used in a manner that is not specified by the manufacturer, the protection provided by the equipment may be impaired 1.11 WASTE ELECTRIC AND ELECTRONIC EQUIPMENT Tecniplast is committed to meeting the requirements of the EU directive 2002/96/EC amended by 2003/108/EC on Waste Electric and Electronic Equipment (WEEE) and, therefore, promotes the reuse, recycling and other forms of recovery of such wastes (WEEE) so as to reduce the disposal of waste. It also seeks to improve the environmental performance of all operators involved in the life cycle of electrical and electronic equipment, e.g. producers, distributors and consumers... Tecniplast has worked closely with its suppliers to eliminate hazardous materials from its products. There are instances, however, where it has not yet been possible to completely eliminate all such materials. Consequently, some products are labelled with a crossed-out "wheelie" symbol, indicating that special care must be applied to their disposal and / or recycling. DO NOT dispose of WASTE ELECTRIC AND ELECTRONIC EQUIPMENT as unsorted municipal waste. Waste electric and electronic equipment is to be collected and disposed of separately in specialised treatment facilities in compliance with EU legislation and any laws and regulations in force in the country where the machinery is installed. 1.12 DISPOSAL OF OTHER MATERIALS DO NOT dispose of plastic material as unsorted municipal waste. Any plastic material is to be collected and disposed of separately in compliance to any norm and regulation in force in the country where the machinery is installed. DO NOT dispose of metallic material as unsorted municipal waste. Any metallic material is to be collected and disposed of separately in compliance to any norm and regulation in force in the country where the machinery is installed. Contact Tecniplast to have detailed specifications and procedures on how to disassemble the EQUIPMENT. 8 2 SAFETY PRECAUTIONS 2.1 SAFETY NOTES The following words and symbols are used in order to explain safety procedures.
- This symbol is used in safety messages and on labels when there is an imminently hazardous situation which, if not avoided, may result in death, serious injury or serious damage to the equipment. These safety messages also describe how the hazard can be avoided.
- This symbol is used to explain any procedures which, if performed incorrectly, could cause damage or potential problems to the equipment.
- This symbol is used to indicate the need to wear personal protective equipment to carry out a specific procedure.
- This symbol is used to indicate that a certain procedure is to be carried out by trained service personnel only.
- This symbol is used to indicate the need to use specific tools and equipment.
- This symbol is used in safety messages and on labels whenever there is the need to refer to product instructions for use. NOTE - Annotations are made for information which requires specific consideration about any procedures, but for which there is no risk of damaging the equipment. Pay special attention to all Safety Warnings given throughout the instructions For any doubts regarding safety, contact TECNIPLAST. 2.2 GENERAL PRECAUTIONS The equipment is to be used by authorised and qualified personnel only. Follow all the precautions, procedures and safety measures prescribed by the standards in force to safeguard personal health and safety. Before using the equipment the user must have a clear understanding of the positioning and functions of the commands. Do not carry out modifications that might alter the performance or the working conditions of the equipment;
TECNIPLAST disclaims all responsibility for personal injury or material damage caused by mishandling of the equipment. If the equipment is used in a manner that is not specified by the manufacturer, the protection provided by the equipment may be impaired. Do not use the equipment in an explosive environment. DO NOT leave the equipment unattended while working. Read the user manual before use. Ensure the equipment is stable and balanced before starting operating. 9 3 APPLICATIONS AND WORKING PRINCIPLE Tecniplast Remote Alarm System (RAS) has been developed to simplify the work of facility managers and operators by providing them with an easy-to-use monitoring of Tecniplast equipment and machines. Each piece of equipment features a transmitter (the TX) which transmits any alarm condition to a receiver (the RX). Each receiver (ideally located inside one of the facility rooms), is designed to receive signals from 10 transmitters and to send at the same time an alarm message to a centralised receiver (the CX) which can monitor a number of RX simultaneously (maximum 10). Any time an alarm is transmitted to the RX (and CX), the system sends a voice message to the phone numbers recorded in the RX setting pages by means of a PSTN dialer*. Voice messages may be customised by the user following the dialer instructions for use directly on the phone. Up to 100 Alarm messages are logged by the system in FIFO logic. Complex System Simple System RX+ PD
................ TX1 TX2 TX10 3.1 HAZARDOUS AND INAPPROPRIATE APPLICATIONS Tecniplast disclaims all responsibility for any uses other than those stated in this User Manual unless previously authorised. Here is a list of some hazardous applications that should be avoided:
Operation by inexperienced or untrained personnel. Housing in an environment not compliant to the Environmental Requirements described in TABLE 1 - TECHNICAL SPECIFICATIONS Operation of the equipment with highly flammable materials. Operation of the equipment in an explosive environment. TECNIPLAST disclaims all responsibilities deriving from improper use and incorrect maintenance If the equipment is used in a manner that is not specified by the manufacturer, the protection provided by the equipment may be impaired
The PSTN dialer is installed in the WW version only. All the related function will not be available on the AMERICA version unit. 10 3.2 MAIN FEATURES 3.2.1 TX TRANSMITTER 1. 2. LED TX Connection Key TX LED STATUS (on-line, off-line) TX STATUS Not linked Linked , on-line LED blink Off (On during transmission every 30 45 seconds) Linked , off-line On 3.2.2 RX AND CX Screen 1. RAS system control panel 2. 3. Antenna 4. Red LED 5. Green LED 6. Yellow LED 7. Alpha-numerical keypad 8. 9. F1, F4 control keys Scroll arrows. 11 4 HANDLING AND TRANSPORTATION 4.1 DISPOSAL OF THE PACKAGING Dispose of the packaging in compliance with laws and regulations in force in the country where the equipment is installed. Collect the packaging and disposed of it separately in compliance with any law and regulation in force in the country where the equipment is installed. DO NOT dispose of plastic film wrapping as unsorted municipal waste. Any plastic material is to be collected and disposed of separately in compliance to laws and regulations in force in the country where the equipment is installed. 4.2 HANDLING The handling of the equipment and of its separate accessories must be carried out by trained personnel. It is advisable to transport the RAS directly to the site where it is going to be installed before removing the packaging. 4.3 INCOMING INSPECTION Upon delivery, unpack the equipment and inspect it for damage. If the equipment has been mishandled, dented or damaged, alert the carrier and Technical Assistance immediately. 4.4 STORAGE The RAS is designed for indoor use only. Always keep the equipment in a dry place, whether packaged or not. If the equipment is not deemed to be used, cover it with a piece of cloth or plastic to protect it from dust and store it in an environment compliant with the environment requirements specified in paragraph 1.5 OPERATING ENVIRONMENTAL CONDITIONS on page 6. If the equipment has been moved, packed and stored, after a period of use (e.g. if there is a change of laboratory or plant), contact Tecniplast technical assistance or the distributor in order to have accurate and precise instructions on how to put it back into service 12 5 RAS SYSTEM INSTALLATION GUIDELINES 5.1 RX AND CX ELECTRICAL CONNECTIONS The RAS is to be connected to the power supply protected by suitable protections in compliance with laws and regulations in force in the country where the machine is installed. The RAS is to be installed in compliance with IEC/EN 60950 Standard, and controlled by an external cut off switch. Before installing the system, connect the Rx and CX to the power supply cable, phone cable and outputs as shown hereunder:
Insert the cables into the slot on the RX and CX housing. Carry on with the following electrical connections:
M5 F1 J4 J3 M3 CONNECTOR CONNECT ONLY SELV (SAFETY EXTRA LOW VOLTAGE) OPERATING CIRCUITS L PE N FUSE LINE PHONE 1 2 3 4 POWER SUPPLY CABLE CONNECTION POINT 5X20mm 1,6 A (TIME LAG) LOW BREAKING CAPACITY 250 Vac. T1.6AL 250V TELEPHONE CABLE Rj11 4 poles DIRECT OUTPUT 1 DIRECT OUTPUT 2 13 into their Insert the connectors housing (M5 - power supply, M3 alarm contact, required by installation specs) and, if necessary, fix them into position. if Connect the power supply cable and signal cables so as to guarantee clearance between mains and SELV circuits so that they do not get in contact. adequate 14 5.2 HOW TO MOUNT THE RX/ CX ON THE WALL Screw the support plates to the RX CX housing Mark four holes on the wall at the most convenient height Drill the wall and insert the screw anchors. Screw the RX CX housing to the wall. 15 5.3 RX, CX AND TX CONNECTION 1. Turn on the CX (if present) 2. Set an ID for each CX If there are many CX installed in the same site, each CX must be given a different ID. SETTINGSUNITRFID CX. 3. Set an ID for each RX SETTINGSUNITRFID RX 4. Set the Country where the system is installed SETTINGSUNITRFCOUNTRY Ensure the selected Country Setting is the same on both the CX and RX before connecting them. Such setting is enabled only during the first start-up or after resetting the sub-network or before connecting the RX. 5. Connect the RX to the CX (if present) 6. The RX screen displays the detected CX. 7. Enter the RX Name on CX 8. Connect the TX to RX RX: SETTINGSUNITCONJUNCTION CX: MENUUNITRECORD Push to connect the RX to the CX Check the TX is connected. Record the TX on the RX RX: MENUUNITRECORDRECORD THE UNIT Press the connection key on the TX (picture below, n. 2) (led 1 off means connected) Enter the TX name on RX. 16 9. Switch off a Unit already registered into the system without generating any Alarm (e.g. for disinfection activity on the Unit) 10. Reset the TX
(If any problem arises) Follow the same procedure to connect all the RX, CX and TX . Before switching off the Unit, press the connection Key for 2 sec and the LED will be ON. On the RX the Unit will be considered OFFLINE and any alarm triggered by the AHU will not be sent to the RX. Press the connection Key again for 2 sec and the Unit will be ON-LINE again. Turn off the AHU. Keep pressed the connection key (2) and turn on the AHU again. Keep pressed for at least 10 seconds. System should be set again from the beginning. 17 6 RAS SYSTEM RECEIVER (RX) SOFTWARE USER GUIDE 6.1 MAIN MENU To open the main menu, press key F1. MENU UNIT ALARMS PSTN DIALER ACCESS TO SOME FUNCTIONS IS ALLOWED TO SUPERVISORS ONLY. UNIT ALARMS PSTN DIALER*
This function allows the user to view, record, delete and rename the units connected to the system. Select UNITS from the MENU list using the UP/DOWN arrows, then push menu. This function allows to view the alarm log. to enter the sub-
Select ALARMS from the MENU list using the UP/DOWN arrows, then push menu. This function allows the user to display the phone numbers to which the system has to send the notifications according to the different alarm priority. to enter the sub-
Select PSTN DIALER from the MENU list using the UP/DOWN arrows, then push sub-menu. to enter the 18 6.2 UNIT MENU UNIT VIEW RECORD ERASE RENAME RECORD THE UNIT
( STANDARD) RECORD THE UNIT RECORD THE RECORD THE UNIT
(MVC) UNIT
(ISO)
(IVC) RECORD THE UNIT CANCEL
(DCC) Unit name Unit name VIEW This function allows to check the connected TX state. To check the connected transmitters (TX) connection status push Record the unit (standard) Record the unit (IVC) RECORD Record the unit (MVC) Record the unit (ISO) Record the unit (DCC) After confirming the password push The system will ask to press the pushbutton on the unit transmitter (Tx ) to record the TX to the RAS system. In this configuration it is not possible to send any alarm. After confirming the password push The system will ask to press the pushbutton on the IVC unit transmitter (Tx ) to record the TX to the RAS system. After confirming the password push The system will ask to press the pushbutton on the Ventilated Cabinet unit transmitter (Tx ) to record the TX to the RAS system. After confirming the password push The system will ask to press the pushbutton on the ISOCAGE unit transmitter (Tx ) to record the TX to the RAS system. After confirming the password push The system will ask to press the pushbutton on the DCC unit transmitter (Tx ) to record the TX to the RAS system. CANCEL Returns to the Menu This function allows to delete the TX from the RX. ERASE RENAME After confirming the password push recorded any longer. This function allows to rename the TX ID. After confirming the password push and delete the TX which you do not want to be and rename the TX 19 6.3 ALARM FUNCTIONS This sub-menu allows to view all the alarms raised by the system. After selecting ALARMS it is possible to see the alarm log screen and check the reported alarm status. The alarm log displays the date and time when the alarm was triggered together with the TX unit name and alarm code. ALARMS Icon next to the alarm message, indicates that the alarm was solved. Icon indicates that the alarm is active. The RAS records up to 100 alarms in FIFO Logic. 20 6.4 PSTN DIALER FUNCTIONS 1 This sub-menu displays the set phone numbers to which the RAS system sends a warning call whenever one of the TX units is triggering an alarm, as well as the user and technical remote codes and RX private phone line number. The phone numbers must be set on the phone dialler (see the phone dialer IM). This sub-menu is only a visualization that act as a reminder for these numbers PSTN DIALER Call Cat. 1 Call Cat. 2 Private Number User remote code Technical remote code CALL CAT. 1 CALL CAT. 2 PRIVATE NUMBER USER REMOTE CODE TECHNICAL REMOTE CODE After confirming the password it is possible to see 5 different phone numbers. After confirming the password it is possible to see 4 different phone numbers Through this function it is possible to see a private number. Through this function it is possible to see the user remote code with 6 digits. Through this function it is possible to see the technical remote code with 6 digits. 1 This menu is enabled only if the set model with PSTN dialer 21 6.5 SETTINGS FUNCTIONS SETTINGS Hour Date Unit Alarms PSTN Dialer Direct Output Password Firmware &
Country Time-out Exit To access the settings functions, push F2 on the numerical key pad After confirming the password it is possible to access different functions such as hour/date, units, alarms, PSTN dialer, direct output, password and firmware & country. 6.5.1 HOURS AND DATE SETTING Hour Date Date: __/__/__ Hour: __/__/__ After confirming the password and selecting hour/date it is possible to record the current time HOUR / DATE and date using the numerical keypad. To confirm the setting push 22 6.6 UNIT SETTINGS Unit RX Name State Model Conjuction RF Default Insert the Unit's name On Line Off Line RX with PSTN Dialer RX without PSTN Dialer CONFIGURATION RESET FACTORY SETTINGS RSSI 00/10 ID Rx
(Insert ID between 0 and 225) Check Tx network
- Check Used Slot
- Full Check Reset Rx network
- Reset full Tx network
- Cancel TX POLLING ATTEMPTS
(3 TO 100) RX Name Through this function it is possible to set the Unit name (ex. LAB 01). Press to confirm. This function allows to set 2 different states: On Line and Off Line. Whenever one unit is online, all information on alarms are transmitted from the TX on the unit to the central receiver RX and alarms are logged by the system. If the unit is offline, the system sees the unit but does not record any messages. Press Through this function it is possible to choose two different models: RX with PSTN Dialer and Rx without to confirm. PSTN Dialer. To select either models, press Push 5.3 RX, CX and TX connection. whenever a record request has been sent by centralized receiver CX. Refer to paragraph RSSI: after confirming the password, press 10). ID Rx: after confirming the password, it is possible to insert the RX ID number between 0 and 225 using to see the received signal level (minimum 1 maximum the numerical keypad. Press Check Tx network: after confirming the password, it is possible to check the Tx network in 2 different ways:
to confirm 1. Check Used Slot: only the Tx recorded will be checked. 2. Full Check: all the Tx recognized will be checked. Press to confirm. Reset Rx network: after confirming the password, it is possible to reset the network:
1. Reset full TX network. 2. Cancel. 23 State Model Conjuction RF RF To select either function press TX polling attempts 3 to 100: after confirming the password it is possible to set the number of polling attempts after which the system automatically triggers the TX Missing Alarm. Default This function allows to go back to default CONFIGURATION or FACTORY SETTINGS 6.6.1 ALARM SETTING PAGE Alarms Erase LOG TYPE OF ALARMS Erase all LOG Cancel STD MODEL CATEGORY IVC MODEL CATEGORY MVC MODEL CATEGORY ISO MODEL CATEGORY DCC MODEL CATEGORY example:
AL 18 - CAT 1
....... ...... ...... ...... Erase LOG Type of Alarms to confirm either function. Through this function it is possible to erase all logged alarms or go back to the menu. Press Through this function it is possible to set the priority for each alarm triggered by the connected unit. 2 different priority levels may be set: CAT 1, high priority, CAT 2, low priority. To save the right configuration press to cancel press F1 24 6.6.2 PSTN DIALER SETTINGS 2 PSTN DIALER Enable Call Cat. 1 Call Cat. 2 Private Number Enter number Enter number Enter number User remote code Enter number Technical remote code Enter number Test Tutorial Enable Call Cat. 1 Call Cat.2 Through this function it is possible to enable/disable the PSTN dialer. Choose between Yes or No and press ENABLE THE DIALER AFTER CARRYING OUT THE SYSTEM SETTINGS IN ORDER TO AVOID TRIGGERING ALARMS Through this function it is possible to save 5 different phone numbers (maximum 26 digits) as a visual reminder of the numbers which the system will contact any time there is a HIGH PRIORITY alarm (the system will call the numbers previously stored in the dialer). Please refer to the dialer operating manual. Enter the numbers using the numerical keyboard and press To delete the number press C Through this function it is possible to save 4 different phone numbers (maximum 26 digits) as a visual reminder of the numbers which the system will contact any time there is a LOW PRIORITY alarm (the system will call the numbers previously stored in the dialer). Please refer to the dialer operating manual. Enter the numbers using the numerical keyboard and press To delete the number press C This page is used to record the RX line phone number (the system will call the numbers previously stored in the dialer). Please refer to the dialer operating manual. Private Number Enter the number using the numerical keypad and press To delete the number, press C 2 This menu is enabled only if the set model with PSTN dialer 25 User Remote Code Through this page it is possible to record (with 6 digits) and view the User remote code which is needed to set up some functions in the dialer. Please refer to the dialer operating manual. Enter the code using the numerical keypad and press To confirm the code, press
, press C to delete it. Technical Remote Code Through this page it is possible to record (with 6 digits) and view the Technical remote code which is needed to set up some functions in the dialer. Please refer to the dialer operating manual. Enter the code using the numerical keypad and press To confirm the code, press
, press C to delete it. Test Run Cat. 1 (HIGH PRIORITY ) call. Through this function it is possible to test the automatic dialer phone calls. F1 F2 C Run Cat. 2 (LOW PRIORITY) call Exit Tutorial PSTN DIALER INSTRUCTIONS FOR USE 26 6.6.3 DIRECT OUTPUT Direct Output Enable State Test Enable Direct OutPut Disable Direct Output Output Normally Opened Output Normally Closed F1 Activate Direct Ouput Cat. 1 F2 Activate Direct Ouput Cat. 2 C Exit Through this function it is possible to ENABLE/DISABLE the direct output Select the desired option and press Through this function it is possible to set the output state:
OUTPUT NORMALLY OPEN and OUTPUT NORMALLY CLOSED. Select the desired option and press Through this function it is possible to test the direct output:
F1 F2 C Activate Direct Output Cat. 2 Activate Direct Output Cat. 1 Exit Enable State Test 27 6.6.4 PASSWORD SETTING Password Insert new password Insert new password Through this function it is possible change password. Enter the new password using the numerical field. Confirm and enter the password again. Press to confirm, press C to delete. 6.7 FIRMWARE Firmware &
Country Country : Geographic area Through this function it is possible to see:
The firmware version loaded in the RX unit. The geographic area setting RX network. Country: Geographic area 28 6.8 TIME-OUT EXIT Time-out Exit Time-Out Exit3 Through this function it is possible to set the time-out value after which the system automatically returns to the home page:
Enter the numerical value (minimum 5 second maximum 240 second) To confirm, press F1 To exit, press
. To delete, press C
. 6.9 LANGUAGE SETTING PAGE LANGUAGE French English Spanish Italian German Portuguese F3 Language Touch languages: Italian, French, English, Spanish and German and Portuguese.
, after inserting the password it is possible to choose among 6 different To select the language press 3 This function is not enabled in the pages where it is possible to insert data (i.e.Hour/Date page) 29 7 RAS SYSTEM CENTRALISED RECEIVER(CX) SOFTWARE USER GUIDE 7.1 MAIN MENU To open the main menu, press key F1. MENU UNIT ALARMS PSTN DIALER ACCESS TO SOME FUNCTIONS IS ALLOWED TO SUPERVISORS ONLY. MENU NAME UNIT FUNCTION This function allows the user to view, record, delete and rename the units connected to the system. ALARMS PSTN DIALER Select UNITS from the MENU list using the UP/DOWN arrows, then push menu. This function allows to view the alarm log. to enter the sub-
Select ALARMS from the MENU list using the UP/DOWN arrows, then push menu. This function allows the user to display the phone numbers to which the system has to send the notifications according to the different alarm priority. to enter the sub-
Select PSTN DIALER from the MENU list using the UP/DOWN arrows, then push sub-menu. to enter the 30 7.2 UNIT MENU UNIT VIEW RECORD ERASE RENAME RECORD THE UNIT RX CANCEL Unit name Unit name MENU NAME VIEW FUNCTION This function allows to check the connected RX state. To check the connected transmitters (RX) connection status push RECORD Record the RX unit
. After confirming the password push The system will ask to press the pushbutton on the RX unit transmitter to record the unit to the RAS system. Refer to paragraph 5.3 RX, CX and TX connection. CANCEL Returns to the Menu ERASE RENAME After confirming the password push any longer. After confirming the password push and delete the RX which you do not want to be recorded and rename the unit 31 7.3 ALARM FUNTIONS This sub-menu allows acknowledge all the alarms raised by the system. ALARMS After selecting ALARMS it is possible to see the alarm log screen and check the reported alarm status. The alarm log displays the date and time when the alarm was triggered together with the TX unit name and alarm code. Icon next to the alarm message, indicates that the alarm was solved. Icon The RAS records up to 100 alarms in FIFO Logic. indicates that the alarm is active. 32 7.4 PSTN DIALER FUNCTIONS 4 This sub-menu displays the set phone numbers to which the RAS system sends a warning call whenever one of the TX units is triggering an alarm, as well as the user and technical remote codes and RX private phone line number. The phone numbers must be set on the phone dialler (see the phone dialer IM). This sub-menu is only a visualization menu that acts as a reminder for these numbers PSTN DIALER Call Cat. 1 Call Cat. 2 Private Number User remote code Technical remote code CALL CAT. 1 CALL CAT. 2 After confirming the password it is possible to see 5 different phone numbers. After confirming the password it is possible to see 4 different phone numbers PRIVATE NUMBER Through this function it is possible to see a private number. USER REMOTE CODE Through this function it is possible to see the user remote code with 6 digits. TECHNICAL REMOTE CODE Through this function it is possible to see the technical remote code with 6 digits. 7.5 SETTINGS FUNCTIONS SETTINGS Hour Date Unit Alarms PSTN Dialer Direct Output Password Firmware &
Country Time-out Exit To access the settings functions, push F4 on the numerical key pad After confirming the password it is possible to access different functions such as hour/date, units, alarms, PSTN dialer, direct output, password and firmware & country. 4This menu is displayed only when the model is set with PSTN dialer 33 7.5.1 HOURS AND DATE SETTING Hour Date Date: __/__/__ Hour: __/__/__ After confirming the password and selecting hour/date it is possible to record the current time HOUR / DATE and date using the numerical keypad. To confirm the setting push 7.6 UNIT SETTINGS Unit CX Name State Model Conjuction RF Default Insert the Unit name On Line Off Line CX with PSTN Dialer CX without PSTN Dialer CONFIGURATION RESET FACTORY SETTINGS RSSI 00/10 ID Cx
(Insert ID between 0 and 225) Check Rx network
- Check Used Slot
- Full Check Reset Cx network
- Reset full Cx network
- Cancel TX POLLING ATTEMPTS
(3 TO 100) CX Name Through this function it is possible to set the Unit name (ex. LAB 01). Press to confirm. State Model This function allows to set 2 different states: On Line and Off Line. Whenever one unit is online, all information on alarms are transmitted from the TX on the unit to the central receiver RX and alarms are logged by the system. If the unit is offline, the system sees the unit but does not record any messages. Press Through this function it is possible to choose two different models: RX with PSTN Dialer and Rx without to confirm. PSTN Dialer. To select either models, press 34 Conjuction RF Push 5.3 RX, CX and TX connection. whenever a record request has been sent by centralized receiver CX. Refer to paragraph RSSI: after confirming the password, press 10). ID Rx: after confirming the password, it is possible to insert the RX ID number between 0 and 225 using to see the received signal level (minimum 1 maximum the numerical keypad. Press Check Tx network: after confirming the password, it is possible to check the Tx network in 2 different ways:
to confirm 3. Check Used Slot: only the Tx recorded will be checked. 4. Full Check: all the Tx recognized will be checked. Press to confirm. Reset Rx network: after confirming the password, it is possible to reset the network:
3. Reset full TX network. 4. Cancel. To select either function press TX polling attempts 3 to 100: after confirming the password it is possible to set the number of polling attempts after which the system automatically triggers the TX Missing Alarm. Default This function allows to go back to default CONFIGURATION or FACTORY SETTINGS 7.6.1 ALARM SETTING PAGE Alarms Erase LOG Type of Alarms Erase all LOG Cancel AL. 31 - Cat. 1/2 AL. 32 - Cat. 1/2 Erase LOG Type of Alarms to confirm either function. Through this function it is possible to erase all logged alarms or go back to the menu. Press Through this function it is possible to set the priority for each alarm triggered by the connected unit. 2 different priority levels may be set: CAT 1, high priority, CAT 2, low priority. To save the right configuration press to cancel press F1 35 7.6.2 PSTN DIALER SETTINGS PSTN DIALER Enable Call Cat. 1 Call Cat. 2 Private Number Enter number Enter number Enter number User remote code Enter number Technical remote code Enter number Test Tutorial Through this function it is possible to enable/disable the PSTN dialer. Enable Choose between Yes or No and press ENABLE THE DIALER AFTER CARRYING OUT THE SYSTEM SETTINGS IN ORDER TO AVOID TRIGGERING ALARMS Through this function it is possible to save 5 different phone numbers (maximum 26 digits) as a visual reminder of the numbers which the system will contact any time there is a HIGH PRIORITY alarm (the system will call the numbers previously stored in the dialer). Please refer to the dialer operating manual. Enter the numbers using the numerical keyboard and press C To delete the number press Through this function it is possible to save 4 different phone numbers (maximum 26 digits) as a visual reminder of the numbers which the system will contact any time there is a LOW PRIORITY alarm (the system will call the numbers previously stored in the dialer). Please refer to the dialer operating manual. Enter the numbers using the numerical keyboard and press Call Cat. 1 Call Cat.2 C To delete the number press This page is used to record the RX line phone number (the system will call the numbers previously stored in the dialer). Please refer to the dialer operating manual. Private Number Enter the number using the numerical keypad and press C To delete the number, press Through this page it is possible to record(with 6 digits) and view the User remote code which is needed to set up some functions in the dialer. Please refer to the dialer operating manual. User Remote Code Enter the code using the numerical keypad and press C to delete it. To confirm the code, press
, press 36 Technical Remote Code Test Tutorial Through this page it is possible to record (with 6 digits) and view the Technical remote code which is needed to set up some functions in the dialer. Please refer to the dialer operating manual. Enter the code using the numerical keypad and press C
, press to delete it. Run Cat. 1 (HIGH PRIORITY ) call. To confirm the code, press Through this function it is possible to test the automatic dialer phone calls. F1 F2 C PSTN DIALER INSTRUCTIONS FOR USE Run Cat. 2 (LOW PRIORITY) call Exit 7.6.3 DIRECT OUTPUT Direct Output Enable State Teste Enable Direct OutPut Disable Direct Output Output Normally Opened Output Normally Closed F1 Activate Direct Ouput Cat. 1 F2 Activate Direct Ouput Cat. 2 C Exit Through this function it is possible to ENABLE/DISABLE direct output Select the desired option and press Through this function it is possible to set the output state:
OUTPUT NORMALLY OPEN and OUTPUT NORMALLY CLOSED. Select the desired option and press Through this function it is possible to test the direct output:
F1 F2 C Activate Direct Output Cat. 2 Activate Direct Output Cat. 1 Exit Enable State Test 37 7.6.4 PASSWORD SETTING Password Insert new password Insert new password To change password:
Enter the new password using the numerical field. Confirm and enter the new password again. Press to confirm, press C to delete. 7.7 FIRMWARE Firmware &
Country Country : Geographic area Through this function it is possible to see:
The firmware version loaded in the RX unit. The geographic area setting RX network. Country: Geographic area 38 7.8 TIME-OUT EXIT Time-Out Exit Time-Out Exit5 To set the time-out value after which the system automatically returns to the home page:
Enter the numerical value (minimum 5 second maximum 240 second) To confirm, press F1 To exit, press
. To delete, press C
. 7.9 LANGUAGE SETTING PAGE LANGUAGE French English Spanish Italian German Portuguese F3 Touch such as Italian, French, English, Spanish, German and Portuguese.
, after inserting the password it is possible to choose among 6 different languages To select the language, press Language 5 This function is not enabled in the pages where it is possible to insert data (i.e.Hour/Date page) 39 8 ALARMS REPORTED BY THE SYSTEM 8.1 ALARMS RAISED BY THE TRANSMITTER
(TX) The RAS is to be connected to the power supply protected by suitable protections in compliance with laws and regulations in force in the country where the machine is installed. Hereunder is the list of the alarm messages which might be sent by the transmitter (TX) to the RX, according to the equipment type. NOTE: Refer to the equipment user manual for a complete troubleshooting. IVC/MVC AL01 MIN SUPPLY FLOW AL02 MAX SUPPLY FLOW AL03 MIN EXHAUST FLOW AL04 MAX EXHAUST FLOW AL05 MIN PRESSURE AL06 MAX PRESSURE AL07 MIN TEMPERATURE AL08 MAX TEMPERATURE AL09 MIN RH%
AL10 MAX RH%
AL11 REPL SUPPLY HEPA AL12 REPL EXHAUST HEPA AL13 SUPPLY AIR FLOW AL14 EXHAUST AIR FLOW AL16 FLOODING ALARM AL23 SUPPLY HOUR-COUNTER WARNING AL24 EXHAUST HOUR-COUNTER WARNING ISOCAGE AL01 MIN PRESSURE AL02 MAX PRESSURE AL03 AIRFLOW AL04 REPL SUPPLY HEPA AL05 REPL EXHAUST HEPA AL06 UPS BATTERY LOW AL07 UPS FAULT AL08 MIN TEMPERATURE AL09 MAX TEMPERATURE AL10 MIN HUMIDITY AL11 MAX HUMIDITY AL23 SUPPLY HOUR-COUNTER WARNING AL24 EXHAUST HOUR-COUNTER WARNING DCC AL03 AIRFLOW AL05 REPL EXHAUST HEPA AL06 UPS BATTERY LOW AL07 UPS FAULT AL08 MIN TEMPERATURE AL09 MAX TEMPERATURE AL10 MIN HUMIDITY AL11 MAX HUMIDITY AL24 EXHAUST HOUR-COUNTER WARNING GENERAL AUX 1 ALARM AUX 2 ALARM AL19 TX POWER FAILURE AL20 TX MISSING AL21 485 COMMUNICATION FAILURE TX OFFLINE 8.2 ALARMS RAISED BY THE RX RX Power failure RX Missing RX Offline 2-00003572-0-02EN
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2013-05-17 | 913 ~ 913 | DXT - Part 15 Low Power Transceiver, Rx Verified | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2013-05-17
|
||||
1 | Applicant's complete, legal business name |
Tecniplast S.p.A.
|
||||
1 | FCC Registration Number (FRN) |
0022521652
|
||||
1 | Physical Address |
Via primo Maggio 6
|
||||
1 |
Buguggiate, N/A
|
|||||
1 |
Italy
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
h******@acbcert.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
SGN
|
||||
1 | Equipment Product Code |
ACBOXTX02
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
A**** R********
|
||||
1 | Telephone Number |
00390********
|
||||
1 | Fax Number |
00390********
|
||||
1 |
a******@tecniplast.it
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Tecniplast
|
||||
1 | Name |
A********
|
||||
1 | Physical Address |
Italy
|
||||
1 |
a******@tecniplast.it
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DXT - Part 15 Low Power Transceiver, Rx Verified | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Transmission of alarm signals | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | Yes | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Istituto Italiano del Marchio di Qualita' S.p.A.
|
||||
1 | Name |
E****** G****
|
||||
1 | Telephone Number |
00390********
|
||||
1 | Fax Number |
00390********
|
||||
1 |
f******@imq.it
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 913.00000000 | 913.00000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC