atl j=
ENT CE COMPLIANCE STATEM TecniToys Juguetes, S.A., Avda. Diagonal 545 7*, 08029 Barcelona, here by states that:
My First Driving School by SCX ref. 18000 Complies with the following European Directives:
- 88/378/EEC as amended by 92/59/EEC and 93/68/EEC. Toy Safety Directive.
~ 99/5/EEC . (Compliance assessment for telecommunications devices}, radio contro! toys This statement is issued based on compliance with the following European Standards:
- EN 71:1998/4 4A5:20001-A1:2001+A2,A6,A7:2002+A8:2003+A9,A10,A1 1:2004) y EN 71:2003/2
- EN 50088:1996 + Ai: 1996 + A2: 1997 + A3: 2002
- EN300-220-1 (V1-3-1 2002-09)
- EN30Q0-220-3 (V1-1-1 2002-09)
- EN301-489-1 (V1-4-1 2002-08)
~ EN301-489-3(V1-4-1 2002-08) Any non specified use of the instruction manual and/or the use of the product for any task or purpose other than that it was designed and manufactured for, will void this statement and be user's entire responsibility. This product was manufactured by a company which complies with European Directive 2002/96/EC conceming electrical and electronic apparatus and management of waste therefrom. The product may contain substances which are harmful to the environment if they are handled improperly or in a manner which contravenes current legislation. The crossed-out container is a symbol illustrating selective disposal of electrical or electronic apparatus in order to encourage its recycling wherever possible. HES Piease show responsibility towards the environment and recycle this product at the end of its useful life, WARNING Improper use of the remote controller batteries may lead to overheating, battery leakage, explosion and damage or injury. Please read the following instructions carefully. Do not attempt to recharge non-rechargeable batteries.
* Remove the batteries from the toy to charge rechargeable batteries.
* Charge rechargeable batteries under supervision.
* Use batteries of the recommended type or the equivalent. Do not short-circuit the power terminals.
* Do not mix different makes of battery together.
* Do not mix new and used batteries.
* Do not mix alkaline, standard (zinc carbon) and rechargeable (Ni-Cd) batteries.
* Insert batteries the right way round as regards polarity, as shown in the battery compartment.
* Remove used batteries from the vehicles and controllers, and dispose of them in the appropriate container.
* Do not put batteries on a fire, or allow them to leak or explode.
* Avoid children handling the batteries. Batteries must be changed by an adult.
* Keep these instructions for future reference. NOTE: phanges or modifications which are not expressly approved by the manufacturer may invalidate the user's authorization to use this device. peng: Changes or modifications tc this unit not expressly approved by the party responsible for compliance could veid the user authority to operate je equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try fo correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. * increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circult different from that to which the receiver is needed, Consult the dealer or an experienced radio/TV technician for help. Only for USA FCC ID; VOH-0014-7T / VSH-0014-9T / VSH-0014-9R, MADE IN CHINA. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.