FCC ID: 2A3MG-TMS580A-400 RF Doppler Sensor ( Motion Sensor )

www.teltron.com Model : TMS580A-400 Telecommunications &

Electronics 5.8 GHz Motion Sensor

[ Features ]

The TMS580A-400 is a 5.8GHz Doppler sensor transceiver module for motion detection, consisting of a single element semiconductor and patch antenna including a phase-fixed loop frequency oscillator, power amplifier, low noise amplifier, and frequency mixer. It provides a reliable solution for motion detection.

[ Picture ]

[ Applications ]

Intrusion alarm Automatic door Obstruction alarm system Non-contact measurement Dual motion sensor with PIR Velocity measurement Automatic on and off lamps Min. Typ. Max. Condition

[Electrical Specifications]

Parameters Frequency Output Power Detection Range 1Note 1 Output Duration

- 3dB Beam Width (E) Operating Voltage Operating Current Operating temp. Storage temp. CW

- 3dB Beam Width (H)

: E-plane

: H-plane 5785 ~ 5815

-18

-17 3 1,800 75

+ 50

+120 92 93 5.0 65

-19 0.2 0.1 55

- 20

-40

-20 ~ +50 Front of antenna CW Unit MHz dBm m sec degree degree V mA mm Size 35.0 24 7.4 Warning : The specifications can be changed without any notice.

#202 Itplex, YusungGu, JangDong 59-2, Daejeon City, Korea 305-343 TEL : +82-42-360-2020 FAX : +82-42-360-2010 email : teltron@teltron.com 1 Telecommunications &

Electronics www.teltron.com 5.8 GHz Motion Sensor Model : TMS580A-400 TMS580A-400

[ Note 1 ]

3 m

[Dimension (Unit : mm)]

Side view 1 Front view Side view 2

[ Pin Description ]

[ Electrical Interface ]

Pin Name Description

1 2 3

+5 V GND OUTPUT Movement detection Power Ground

+5 V OUTPUT AC-DC converter SMPS etc. Active high

#202 Itplex, YusungGu, JangDong 59-2, Daejeon City, Korea 305-343 TEL : +82-42-360-2020 FAX : +82-42-360-2010 email : teltron@teltron.com 2 Telecommunications &

Electronics www.teltron.com 5.8 GHz Motion Sensor Model : TMS580A-400

[FCC Compliance Statement]

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

[FCC Interference Statement]

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

[FCC Caution]

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

#202 Itplex, YusungGu, JangDong 59-2, Daejeon City, Korea 305-343 TEL : +82-42-360-2020 FAX : +82-42-360-2010 email : teltron@teltron.com 3 Telecommunications &

Electronics www.teltron.com 5.8 GHz Motion Sensor Model : TMS580A-400 INTEGRATION INSTRUCTIONS per FCC KDB 996369 D03, Section 2.0 2.2 List of applicable FCC rules The module has been certified for use under FCC Part 15.249 only 2.8 Label and compliance information FCC ID: 2A3MG-TMS580A-400 If the module's FCC ID is not visible when installed in the host system then the host system shall be labeled with "Contains FCC ID: 2A3MG-TMS580A-400". The host devices user manual shall contain, in addition to the compliance information required for the host system for e.g. Part 15 subpart B, the following statements:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 2.9 Information on test modes and additional testing requirements To verify that your installation of the module into your host device has not compromised compliance with FCC rules we recommend performing spot checks with the module operational to check that emissions remain below the FCC 15.249 limits. Refer to FCC KDB 996369 D04. 2.10 Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.249 and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. This includes Part 15 subpart B requirements for unintentional radiators. Host manufacturers are responsible for the approvals of the host system with this module installed for Part 15 B when applicable following the appropriate procedures for SDoC or certification.

#202 Itplex, YusungGu, JangDong 59-2, Daejeon City, Korea 305-343 TEL : +82-42-360-2020 FAX : +82-42-360-2010 email : teltron@teltron.com 4

Label Info & Location

[TMS580A-400 TOP]

10mm 15mm

[Bottom of the device]

TELTRON Inc. MODEL : TMS580A-400 Operating Voltage : 5V FCC ID: 2A3MG-TMS580A-400

Teltron Inc. No.202, Itplex, Gajungbug-ro 26-41, Yusung-gu, Daejeon, South Korea Tel. +82-42-360-2028, Fax. +82-42-360-2010 Date: November 18, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern:

I, the undersigned, hereby authorize Ms. Chloe Lee / Deputy General Manager of KCTL Inc. and hereafter referred to as KCTL to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Chloe Lee / Deputy General Manager of KCTL Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KCTL as our agent, we still recognize that we are responsible to:

a) b) c) d) comply with the relevant provisions of the certification program;

make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) f) g) h) i) j) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, SOO-HO LEE / Assistant Manager

Teltron Inc. No.202, Itplex, Gajungbug-ro 26-41, Yusung-gu, Daejeon, South Korea Tel. +82-42-360-2028, Fax. +82-42-360-2010 CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 November 19, 2021 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, Teltron Inc. requests confidentiality for the following products:

FCC ID Number Product Title/Model 2A3MG-TMS580A-400 RF Doppler Sensor (Motion Sensor) / TMS580A-400 The following exhibits contain trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our product. This material is not customarily available to the general public and we request that it be withheld from public inspection. We request that the following information submitted be held permanent confidential treatment. Permanent Confidential Request

-. Schematics

-. Block Diagram

-. Operational Description

-. Antenna specification

-. External Photos

-. Internal Photos

-. Test set-up photo

-. User Manual We also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give temporary confidentiality of commercially sensitive information prior to product release. Short-Term Confidential Request If you have any questions, please feel free to contact me at the address shown below. Sincerely, SOO-HO LEE / Assistant Manager

Applicant/Grantee Teltron Inc. FCC ID:

2A3MG-TMS580A-400 Request for Modular Approval Request for Limited Modular Approval Section 15.212 Modular Transmitters Requirements EUT Conditions Single Modular Approval Requirements Comply (Y/N)

-Operating Voltage : 5V

- A LDO is configured for internal supply of the module. Connected to antenna with internal transmission line and matching. Y Y Y Y Y 1 2 3 4 5 OK OK The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-

modulation. The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph

(b) of this section. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines OK 6 Mark the FCC-ID certification number on the module label. Y connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID: XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy Module usage manuals were provided. Y 7 8 of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. OK Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.