FCC ID: 2AEIM-BTVMS01 TPMS Sensor

Tesla Inc. 3500 Deer Creek Road, Palo Alto, CA. 94304 Model: BTVMS01 Tire Pressure Monitoring Sensor PMN: TPMS Sensor Operating Temperature: -40C to +120C EU:

Tesla Motors Netherlands B.V. Asteriastraat 1-7 5047 RM Tilburg The Netherlands User Manual The TPMS Transmitter is installed to the valve stem in each tyre of a vehicle. The unit measures tyre pressure periodically and transmits this information by RF communication to a receiver inside the vehicle. In addition, the TPMS Transmitter performs the following functions:

Determines a temperature compensated pressure value. Determines any abnormal pressure variations in the wheel. Monitors the state of the Transmitters internal battery and informs the receiver of a low battery condition. Modes Rotating Mode While the sensor/transmitter in the Rotating Mode, it shall satisfy the following requirements. The sensor/transmitter shall transmit an instantaneous measured data, if a pressure change of 2.0 psi from the last transmission or greater has occurred with respect to the following conditions. If the pressure change was a decrease of pressure, the sensor/transmitter shall transmit immediately every time it detects the 2.0-psi or greater pressure changes from the last transmission. If the pressure changes of 2.0 psi or greater was an increase of pressure, the sensor shall not react to it. Stationary Mode While the sensor/transmitter in the Stationary Mode, it shall satisfy the following requirements. The sensor/transmitter shall transmit an instantaneous measured data, if a pressure changes of 2.0 psi from the last transmission or greater has occurred with respect to the following conditions. If the pressure change was a decrease of pressure, the sensor/transmitter shall transmit immediately every time it detects the 2.0-psi or greater pressure changes from the last transmission. If the pressure changes of 2.0 psi or greater was an increase of pressure, the silent period between the RPC transmission and the last transmission shall be 30.0 seconds, and the silent period between the RPC transmission and the next transmission (Normal scheduled transmission or another RPC transmission) shall also be 30.0 seconds, to be in compliance of FCC Part 15.231. Factory Mode The factory mode is the mode that the sensor shall transmit more often in the factory to assure the programmability of the sensor ID during the manufacturing process. Off Mode This Off Mode is only for production parts sensors that are used for the builds during the production process and not in the service environment. LF Initiation The sensor/transmitter must provide data upon the presence of an LF signal. The sensor must react (Transmit and provide data) no later than 150.0 ms after the LF data code has been detected at the sensor. The sensor/transmitter must be sensitive (As sensitivity is defined in Table 1) and able to detect the LF field. RF Frequency Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures:

connected. Compliance with 2014/53/EU Radio Equipment Directive (RED) In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency bands used and the maximum RF transmit power of the product for sale in the EU:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is Consult the dealer or an experienced radio/TV technician to help. Frequency range (MHz) Max. Transmit Power 2400-2483.5 MHz

-0.82 dBm This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Note: FCC Radiation exposure: All equipment complies with FCC and IC RSS-102 radiation exposure limits for an uncontrolled environment and the radio device and antennas operating at more than 20cm distance from user. FCC ID: 2AEIM-BTVMS01 IC: 20098-BTVMS01 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. WARNING: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term IC: before the radio certification number only signifies that Industry Canada technical specifications were met.

NCC

Mexico Uso del Espectro Radioelctrico La operacin de este equipo est sujeta a las siguientes dos condiciones:

Es posible que este equipo o dispositivo no cause interferencia perjudicial. Este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada.

1 2 3 4 5 REV 01 6 REVISION DESCRIPTION INITIAL RELEASE 7 BY ECO 8 DATE M.W. ECO-529419 27/SEP/2023 TABLE 1 - MANUFACTURING CODE MECH CODE 01924 TABLE 2 - PRODUCTION LOCATION PRODUCTION LOCATION COUNTRY OF MANUFACTURE AGUASCALIENTES ANTRIM MEXICO UK TABLE 3 - PRODUCT MARKINGS ITEM DESCRIPTION VALUE FORM SIZE REQUIRED 01 02 03 04 05 06 07 08 09 10 11 12 TESLA PART NUMBER 1819592-00-A SENSATA PART NUMBER 70503117292 TESLA SYMBOL N/A LASER LASER LASER PRODUCTION LOCATION MADE IN XXXXXX LASER BLUETOOTH SYMBOL N/A LASER LEGIBLE LEGIBLE LEGIBLE LEGIBLE LEGIBLE MAC ADDRESS

(HEXADECIMAL) FREQUENCY ASIC ID:

XXXXXXXXXXXX 2.4GHZ DATE OF MANUFACTURE YYMMDD LASER LEGIBLE LASER LASER LEGIBLE LEGIBLE 2D DATA MATRIX (SENSATA) 2D DATA MATRIX (SENSATA) N/A N/A LASER 5MM x 5MM LASER 10MM 3MM 2D DATA MATRIX (TESLA) TESLA DATA STRING LASER 10MM x 10MM TESLA DATA STRING SEE TABLE 5 LASER LEGIBLE TABLE 4 - COUNTRY APPROVALS ITEM REGION AUTHORITY FREQUENCY

(GHz) REF CODE/TEXT

[TEXT FONT: DIN1451]

REQ ON SENSOR SIZE REQUIRED 13 14 15 16 17 18 19 20 21 22 23 24 KOREAN KCC AUSTRALIA ACMA TAIWAN EUROPE JAPAN RUSSIA UK MEXICO USA CANADA BRAZIL CHINA NCC R&TTE MIC TR CU UKCA IFT FCC IC ANATEL SRRC TABLE 5 - TESLA DATA STRING DATA CHARACTERS PART NO. ORIGIN YEAR DAY UNIQUE ID 14 4 2 3 6 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 2.4 XXXX-XXX-XXX-XXXXXX TEXT & SYMBOL LEGIBLE

SYMBOL 3MM HIGH NCC: XXXXXXXXXXXXXX TEXT & SYMBOL LEGIBLE

CE SYMBOL 4MM HIGH XXX-XXXXXX TEXT & SYMBOLS 3MM & LEGIBLE

SYMBOL SYMBOL 5MM HIGH 5MM HIGH IFT: XXXXXXXXX-XXXX FCC ID: 2AEIM-BTVMS01 IC: 20098-BTVMS01 ANATEL: XXXX-XX-XXXX CMIIT ID: XXXXXXXXXX TEXT TEXT TEXT TEXT TEXT LEGIBLE LEGIBLE LEGIBLE LEGIBLE LEGIBLE VALUE P1819592-00-A:

SXXX WITH XXX BEING AMY FOR AGUAS, GEV FOR ANTRIM LAST TWO DIGITS OF YEAR, FOR EXAMPLE, 23 FOR 2023 001 TO 365 (366 FOR LEAP YEAR) WITH 001 BEING 01ST JAN SEQUENTIAL FROM 000001 A B C D E F 09 16 13 15 14 1819592-00-A 70503117292 MADE IN XXXXXX MODEL: BTVMS01 IC: 20098-BTVMS01 FCC ID: 2AEIM-BTVMS01 CMIIT ID: XXXXXXXXXX ANATEL: XXXX-XX-XXXX NCC: XXXXXXXXXXXXXX XXXX-XXX-XXX-XXXXXX IFT: XXXXXXXXX-XXXX ASIC ID: XXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXX 13,15, 20-24 12 01 02 03 04 06 11 18 2.4GHZ YYMMDD X X X X X X

X X X 07 08 05 17 19 D R A F T - F O R T E C H N I C A L F E E D B A C K O R Q U O T A T I O N P U R P O S E S O N L Y S U P P L I E R S - P L E A S E N O T E W H E N I N C O M M U N I C A T I O N W I T H S E N S A T A A B O U T D R A F T I T E M S , P L E A S E U S E P A R T N U M B E R T O G E T H E R W I T H 3 D C A D V E R S I O N A S U N I Q U E I D E N T I F I E R O F R E F E R E N C E D 3 D C A D M O D E L D R A W I N G V E R S I O N 3 D C A D V E R S I O N P A R T N O . 7 0 5 0 3 1 1 7 2 9 2 1 5 10 FOR REFERENCE ONLY, CHECK LATEST REVISION BEFORE USE. REFER TO PLM FOR CONTROLLED DATA, CHANGE HISTORY AND APPROVALS. TECHNOLOGY PARK, ANTRIM, UK, BT41 1QS MATERIAL N/A MASS (g) N/A PROJECT NO. PRJ0014620 REVISION SYMBOL THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY OF SCHRADER ELECTRONICS LIMITED. THE INFORMATION CONTAINED WITHIN IT MAY NOT BE USED, DISCLOSED OR REPRODUCED IN WHOLE OR PART, WITHOUT THE EXPRESSED WRITTEN CONSENT OF SCHRADER ELECTRONICS LIMITED. NO RIGHT IS GRANTED TO DISCLOSE OR USE ANY INFORMATION CONTAINED WITHIN THIS DRAWING. SCHRADER ELECTRONICS LIMITED IS PART OF THE SENSATA TECHNOLOGIES GROUP. INTERPRET DRAWING PER ASME Y14.5-2009 SEE NOTES FOR GENERAL TOLERANCE PART NUMBER 70503117292 TITLE TESLA DELTA 2.4GHZ SILVER 70503117292 LASER MARKING DRAWING -

DRAFT SIZE DRAWING NO. DRAWING REV. A3 00019624 01 SCALE 2:1 SOLIDWORKS 2020 SHEET 1 OF 1 EXAMPLE TEXT STRING: "P1819592-00-A:SGEV24001000001" WOULD BE THE FIRST PART MADE IN ANTRIM ON 01ST JAN 2024 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS DO NOT SCALE DRAWING THIRD ANGLE PROJECTION ENG-F-044 ISS 05 1 2 3 4 5 6 7 8 A B C D E F

To Whom It May Concern:

Authority to Act as Agent and REL Listing Attestation We appoint Joseph D. Brunett on behalf of Willow Run Test Labs, Inc. and Amber Helm Development, LC and Brad Koski of Wireless Approval Consultants, LLC to act as our agents in the preparation of applications for FCC and ISED equipment authorization for product:

FCC ID: 2AEIM-BTVMS01 IC: 20098-BTVMS01 Product Name: TPMS sensor We certify that submitted documents properly describe the device or system for which equipment certification is sought. We also certify that each unit manufactured, imported or marketed (as defined in Industry Canadas regulations) will have affixed to it a label identical to that submitted for approval with this application. Further, in accordance with section 6.5 of IC CB-02, we hereby acknowledge that our companys product cannot be distributed, leased or offered for sale in Canada until its listed on the Industry Canada Radio Equipment List (REL). For instances where our authorized agent signs the application for certification on our behalf, we acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by American Certification Body, Inc. and/or TUV Rheinland Group and/or Vista Laboratories, Inc. still resides with Tesla, Inc. 3500 Deer Creek Road, Palo Alto. USA For TCB applications, we certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) regarding certified equipment. Agency Agreement Expiration Date: 1/28/2025 Dated this ______________day of __________, 20___. By:

Title:

email:

On behalf of:

Telephone:

Page 6 of 9

(Signature) _____Cindy Li_______________

(Print name) Certification Engineer [email protected] Tesla, Inc

(Company Name)

+1-408-718-7809

Federal Communications Commission Office of Engineering & Technology Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Via Electronic Filing Date: April 28, 2021 Re: Authorized Personnel for Grantee Code 2AEIM To Whom It May Concern:

I currently serve as Tesla, Incs (Tesla) grantee contact (Grantee Code 2AEIM) for Federal Communications Commission (FCC) equipment authorizations. As prescribed in KDB 852134 Authorized Policy Form 731, I authorize the following personnel to act on Teslas behalf with regard to all matters that relate to FCC equipment authorization (i.e., signing Form 731, attestation letters, and confidentiality request letters). These individuals also are authorized to assign additional persons to act on Teslas behalf as authorized agents. Authorized Personnel:

Peng Zhang Cindy Li This authorization is valid until further written notice from any of Teslas authorized grantee contacts. Sincerely Yours, Sean Lui Sr. Staff Charging Compliance Engineer 3500 Deer Creek Road, Palo Alto, California US 94304 Phone: (650)681-5109 [email protected] Tesla, Inc. 3500 Deer Creek Road, Palo Alto, CA 94304 p +650 681 5100 f +650 681 5101

Willow Run (WR) Test Labs, Inc. 7117 Fieldcrest Dr., Brighton, Michigan 48116 USA Tel: (734) 252-9785, Fax: (734) 926-9785, e-mail: [email protected] Attn.:Certification and Engineering Bureau, Innovation, Science and Economic Development Canada 3701 Carling Avenue, Bldg. 94 Ottawa, Ontario K2H 8S2 Re: Certification for Tesla, Inc. BTVMS01 IC: 20098-BTVMS01 If necessary, we have enclosed application materials for certification of Tesla, Inc. BTVMS01. It has been verified to comply with IC RSS-247v3/GENe. Current Variants:

There is only a single variant of the EUT, as tested. History:

Original Grant: November, 2023; FCC ID: 2AEIM-BTVMS01; IC: 20098-BTVMS01, Model: BTVMS01. Changes Made:

The manufacturer may deploy this product without the tire valve stem originally mounted to the device chassis. While this valve stem element is not electrically in contact with the products PCB or antenna, measured data suggests that the product must undergo a Class II permissive change to demonstrate ongoing compliance. Action Taken:

The EUT without the tire valve stem is fully tested and data reported herein. The changes made qualify as a permissive change for IC (ref. IC RSP-100). If there are any questions regarding the application or testing performed, please contact us at the above address or call (734) 252-9785, or e-mail [email protected]. Sincerely, Joseph D. Brunett Willow Run (WR) Test Labs, Inc. 11 Willow Run (WR) Test Labs, Inc. 7117 Fieldcrest Dr., Brighton, Michigan 48116 USA Tel: (734) 252-9785, Fax: (734) 926-9785, e-mail: [email protected] Attn.:Federal Communications Commission Equipment Approval Services P.O. Box 358315 Pittsburgh, PA 15251-5315 Re: Certification for Tesla, Inc. BTVMS01 FCC ID: 2AEIM-BTVMS01 If necessary, we have enclosed application materials for certification of Tesla, Inc. BTVMS01. It has been verified to comply with CFR Title 47, Part 15.247/15.109. Current Variants:

There is only a single variant of the EUT, as tested. History:

Original Grant: November, 2023; FCC ID: 2AEIM-BTVMS01; IC: 20098-BTVMS01, Model: BTVMS01. Changes Made:

The manufacturer may deploy this product without the tire valve stem originally mounted to the device chassis. While this valve stem element is not electrically in contact with the products PCB or antenna, measured data suggests that the product must undergo a Class II permissive change to demonstrate ongoing compliance. Action Taken:

The EUT without the tire valve stem is fully tested and data reported herein. The changes made qualify as a permissive change for FCC (ref. FCC, Part 2, 2.1043(a)(1)).If there are any questions regarding the application or testing performed, please contact us at the above address or call (734) 252-9785, or e-mail [email protected]. Sincerely, Joseph D. Brunett Willow Run (WR) Test Labs, Inc. 10

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: November 13, 2024 FCC ID: 2AEIM-BTVMS01 FRN: 0020169504 RE: Attestation Statements Part 2.911(d)(5)(i) Filing Tesla, Inc (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: N/A RE: Attestation Statements Part 2.911(d)(5)(ii) Filing Tesla, Inc (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Applicant Address Signature

: Tesla, Inc

: 3500 Deer Creek Road, Palo Alto, California 94304, United States

Name and Job Title.

: Cindy Li, Certification Engineer _____ ____________________________ E-mail Tel.

: [email protected]

: +1-408-718-7809

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: October 31, 2024 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AEIM-BTVMS01 Tesla, Inc (the applicant) certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. The applicant as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC Grantee Code. The service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. The applicant acknowledges that they will maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the following agent information changes. Designated U.S. Agent Information:

FRN: 0020169504 Name: Tesla, Inc Address: 3500 Deer Creek Road, Palo Alto, California 94304, United States Contact Person: Cindy Li Tel.: +1-408-718-7809 Email: [email protected] Sincerely, Applicant Tesla, Inc Cindy Li, Certification Engineer Signature:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 30, 2023 FCC ID: 2AEIM-BTVMS01 RE: Attestation Statements Part 2.911(d)(5)(i) Filing Tesla, Inc (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. RE: Attestation Statements Part 2.911(d)(5)(ii) Filing Tesla, Inc (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Applicant Address

: Tesla, Inc

: 3500 Deer Creek Road, Palo Alto, California 94304, United States Signature

_____ ____________________________ Name and Job Title.

: Cindy Li, Certification Engineer E-mail Tel.

: [email protected]

: +1-408-718-7809

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 30, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing Grantee Code: 2AEIM Tesla, Inc (the applicant) certifies that, as of the date of the filing of the application, we designate ourselves as the U.S. agent for service of process. The applicant as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC Grantee Code. The service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. The applicant acknowledges that they will maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the following agent information changes. Designated U.S. Agent Information:

FRN: 0020169504 Name: Tesla, Inc Address: 3500 Deer Creek Road, Palo Alto, California 94304, United States Contact Person: Cindy Li Tel.: +1-408-718-7809 Email: [email protected] Sincerely, Applicant Tesla, Inc Cindy Li, Certification Engineer Signature:

Date: August 30, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: declaration of composite/rated equipment for FCC ID: 2AEIM-BTVMS01 To Whom it may concern, We, the undersigned, would like to declare that the composite portion catagorized as Other Class B digital devices & peripherals has been authorized under the Supplier's Declaration of Conformity (SDoC) procedures. Sincerely, Applicant Address Signature

: Tesla, Inc

: 3500 Deer Creek Road, Palo Alto, California 94304, United States

__ _______________________________ Name and Job Title.

: Cindy Li, Certification Engineer E-mail Tel.

: [email protected]

: +1-408-718-7809

Letter of Authorization Date: August 30, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: 2AEIM-BTVMS01 Product Name: TPMS sensor To whom it may concern:

We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization to the FCC Rules and Regulations. Sporton International Inc. Address

No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Name

: Leo Huang Job Title : VP e-mail

: [email protected] We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Applicant Address

: Tesla, Inc

: 3500 Deer Creek Road, Palo Alto, California 94304, United States Signature

_______________________________ Name and Job Title.

: Cindy Li, Certification Engineer E-mail Tel.

: [email protected]

: +1-408-718-7809

Confidentiality Request Letter Date: August 30, 2023 Federal Communications Commission Authorization and Evaluation Division Subject: Request for confidentiality FCC ID: 2AEIM-BTVMS01 To whom it may concern:

Short-term Confidentiality pursuant to Public Notice DA 04-1705, and in order to comply with the marketing regulations in 47 C.F.R. 2.803 and the importation rules in 47 C.F.R. 2.1204 while ensuring that business-sensitive information remains confidential until the actual marketing of newly authorized devices, we are request the Commission grant temporary confidential treatment and not release the following attachments for routine public disclosure until 180 days after the grant date. 1. Internal Photographs 2. External Photographs 3. Users manual 4. Test Set up photos Permanent Confidentiality Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. 1. Block Diagram 2. Schematics 3. Operational Description It is our understanding that test measurement reports and correspondence during the certification review process cannot be granted confidential treatment, and such information will be available for public review once the grant of equipment authorization is issued. Sincerely, Applicant Address

: Tesla, Inc

: 3500 Deer Creek Road, Palo Alto, California 94304, United States Signature

______________________________ Name and Job Title.

: Cindy Li, Certification Engineer E-mail Tel.

: [email protected]

: +1-408-718-7809