FCC ID: 2AEIM-WC1 Wireless Phone Charger

Model S/X Wireless Charger The Model S/X wireless phone charger can charge your Qi-enabled smartphone at up to 7.5W of power for Model S/X. Once installed, simply push on the center console rear bin lid to open and place your smartphone in the phone charger, which is located on the back of the bin cover. The wireless phone charger uses one of the front USB ports to charge. Installing Wireless Phone Charger To install:

1. Open the rear bin storage area in the center console. This area is the storage portion closest to the cup holders, where the 12V power socket and USB ports are located. 2. Remove the rubber mat from the bottom of the console. 3. Lower the wireless phone charger onto the back of the console storage cover while open. You will hear a snap when it has secured tightly. 4. Locate the USB ports and insert the charger into either port. 5. Route the wire through the wiring indent and ensure the wire does not stick up. 6. Reinstall the plastic mat in the center console. 7. Place your smartphone into the wireless phone charger. It should fit snugly and will automatically start charging. Model S/X will charge your smartphone only when the vehicle is powered on (i.e., the touchscreen is on, and you are in your vehicle). You smartphone will not continue to charge if you leave it plugged in after exiting the vehicle. Model S/X will not charge your smartphone if the vehicles battery is discharged. NOTE: The wireless phone charger many not work if your phone case is too large or made of medal. Take the phone out of the case and place the phone on the charger. FCC and IC Certification Component Wireless charger Manufacturer Tesla Model WC1 Operating Frequency

(KHz) FCC ID IC 127.7 2AEIM-WC1 20098-WC1 The devices listed above comply with Part 15 of the FCC rules and Industry Canada's license-

exempt RSS Standard(s) and EU Directive 2014/53/EU. Operation is subject to the following two conditions:

1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Changes or modifications not expressly approved by Tesla could void your authority to operate the equipment Note: Radiation Exposure Statement The product comply with the FCC/IC RF Exposure for Low Power Consumer Wireless Power Transfer. RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure that compliance was demonstrated at 20cm and greater separation from the user body or set the device to lower output power if such function is available. Dclaration d'exposition aux radiations:

Le produit est conforme l'exposition RF IC pour le transfert de puissance sans fil de consommateurs de faible puissance. La limite d'exposition RF fixe pour un environnement non contrl est sans danger pour le fonctionnement prvu tel que dcrit dans ce manuel. L'exposition RF supplmentaire que la conformit a t dmontre 20cm et plus de sparation du corps de l'utilisateur ou de mettre l'appareil la puissance de sortie infrieure si une telle fonction est disponible. Canada CAN ICES-3 (B)/NMB-3(B) Caution: This equipment and its antennas must not be co-located or operated with another antenna or transmitter. Caution: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. EU Declaration of Conformity Hereby, Tesla Motors, Inc. , declares that the radio equipment Wireless Charging, WC1, is in compliance with Directive 2014/53/EU. The full test of the EUT declaration of conformity is available at the following. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Radiation Exposure Statement: This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Frequency band in which the radio equipment operates: 127.7 kHz Maximum power transmitted: < 0.01mW Mexico La Operacin de Este Equipo no est Sujeta a las dos condiciones siguientes:

Es Posible Que Este Equipo o Dispositivo no causar interferenciaperjudicial. Este Equipo o Dispositivo debe Aceptar Cualquier interferencia. Incluyendo La Que Pueda causar do Operacin no Deseada. Model name: Wireless Phone Charger Manufacturer: Tesla, Inc. Model Number: WC1 Max. output: 7.5W Input:5V 3.5A

REV. DESCRIPTION ENG. APPROVAL CAN ICES-3 (B)/NMB-3(B) Made in China TRC/XX/XXXX/XXX R3D160 RoHS

(P)1546873-00-A

(S)AOV19295000001

:P 1546873-00-A

:SAOV19295000001 76mm 1 2 m m 2 1 Model Name: Wireless Phone Charger Manufacturer: Tesla, Inc. Model Number: WC1 FCC ID: 2AEIM-WC1 IC: 20098-WC1 Input:5V 3.5A XXXXXXXXXX R-C-Tsa-WC1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. TRC/XX/XXXX/XXX Made CAN ICES-3 (B)/NMB-3(B) in China R3D160 RoHS

(P)1546873-00-A

(S)AOV19295000001 2pcs label(1:1) NOTE :

1.All fonts is 4pt 2.MATERIAL : White PET 50g 3.PRINT COLOR: BLACK CODE QR CODE 4.THE BARCODE ARRANGEMENT IS 5.BARCODE ARRANGEMENT :

FOLLOWING THE STANDARD ASII CODES. Fixed code Part Number Fixed code Build Site Code Build Date Unique ID P 1546873-00-A: S AOV 19295 000001

AOV=

19295=

SSS

:Build Site Code

=>Build Date YYJJJ YY=(18=2018,19=2019...) JJJ=Refer to TABLE A1&TABLE A2

= >Unique ID 000001=

CCCCCC

(DIGITS 0~9 AND CAPITAL LETTERS A~Z) 6.TO BE PRINTED IN PRODUCTION USING DMX300 RIBBON ;

7.THE DIMENSIONS (2) ARE INCOMING INSPECTION AND CRITICAL. 8. ALL TOLERANCE ARE +/-0.01MM . 9.Requirement of PRIMAX Part:

1).Comply with PRIMAX QW-5Q002 Green Product Chemical Substances Specification . 2).Follow customer's specification as required. Follow Halogen- Free requirement : Br<900 ppm, Cl<900 ppm, 3). Br+Cl< 1500 ppm if required.

"Product must be halogen free"

PRIMAX ELECTRONICS LTD. WCI_T75 Zhibing.Wu 2019/12/2 Becky.Liu 2019/12/2 PRODUCT LABEL A910000000920 A910000000920V7.PDF 3 1 T h i s d e v i c e c o m p l i e s w i t h P a r t 1 5 o f t h e F C C R u l e s

. O p e r a t i o n i s s u b j e c t t o t h e f o l l o w i n g t w o c o n d i t i o n s

1

) t h i s d e v i c e m a y n o t c a u s e h a r m f u l i n t e r f e r e n c e

, a n d

2

) t h i s d e v i c e m u s t a c c e p t a n y i n t e r f e r e n c e r e c e i v e d

, i n c l u d i n g i n t e r f e r e n c e t h a t m a y c a u s e u n d e s i r e d o p e r a t i o n

. b 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Jan 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Feb 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 Mar 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 TABLE A1: Julian Date Calendar Apr 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 Sep 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 Jun 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 May 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 Aug 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 Jul 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 Oct 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 Nov 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 Dec 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 Requirement of PRIMAX Part:

1).Comply with PRIMAX QW-5Q002 Green Product Chemical Substances Specification . 2).Follow customer's specification as required. 3). Follow Halogen- Free requirement : Br<900 ppm, Cl<900 ppm, Br+Cl< 1500 ppm if required.

"Product must be halogen free"

REV. DESCRIPTION ENG. APPROVAL PRIMAX ELECTRONICS LTD. WCI_T75 Zhibing.Wu 2019/12/2 Becky.Liu 2019/12/2 PRODUCT LABEL A910000000920 A910000000920V7.PDF 32 1 TABLE A2: Julian Date Calendar Leap Year Feb 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Sep 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 Jun 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 Apr 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 May 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 Aug 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 Mar 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 Jul 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 Oct 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 Nov 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 Dec 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 b 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Jan 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Requirement of PRIMAX Part:

1).Comply with PRIMAX QW-5Q002 Green Product Chemical Substances Specification . 2).Follow customer's specification as required. 3). Follow Halogen- Free requirement : Br<900 ppm, Cl<900 ppm, Br+Cl< 1500 ppm if required.

"Product must be halogen free"

REV. DESCRIPTION ENG. APPROVAL PRIMAX ELECTRONICS LTD. WCI_T75 Zhibing.Wu 2019/12/2 Becky.Liu 2019/12/2 PRODUCT LABEL A910000000920 A910000000920V7.PDF 33 1

Date: 2019-11-28 FCC ID:2AEIM-WC1 AUTHORIZATION LETTER To Whom It May Concern:

Tesla Motors, Inc hereby authorizes Andrea Hsia / Supervisor of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan), to act on its behalf in all matters relating to the Federal Communication Commission (FCC) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Andrea Hsia /

Supervisor of BV CPS Taoyuan on Tesla Motors, Incs behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours,

Peng Zhang, Sr Certification Engineer Tesla Motors, Inc Tel: 650-681-5000 E-mail: pengzhang@tesla.com

Date: 2019-11-28 FCC ID:2AEIM-WC1 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours,

Peng Zhang, Sr Certification Engineer Tesla Motors, Inc Tel: 650-681-5000 Fax: 650-681-5000 E-mail: pengzhang@tesla.com

Date: 2019-11-28 FCC ID:2AEIM-WC1 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commissions rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

External photos Test Setup photos Users manual Internal Photos Sincerely yours,

Peng Zhang, Sr Certification Engineer Tesla Motors, Inc Tel: 650-681-5000 Fax: 650-681-5000 E-mail: pengzhang@tesla.com

Federal Communications Commission Office of Engineering & Technology Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Via Electronic Filing Date: Oct 3, 2019 Re: Authorized Personnel for Grantee Code 2AEIM To Whom It May Concern:

I currently serve as Tesla, Incs (Tesla) grantee contact (Grantee Code 2AEIM) for Federal Communications Commission (FCC) equipment authorizations. As prescribed in KDB 852134 Authorized Policy Form 731, I authorize the following personnel to act on Teslas behalf with regard to all matters that relate to FCC equipment authorization (i.e., signing Form 731, attestation letters, and confidentiality request letters). This (these) individual(s) also is (are) authorized to assign additional persons to act on Teslas behalf as authorized agents. Authorized Personnel:

Peng Zhang This authorization is valid until further written notice from any of Teslas authorized grantee contact(s). Sincerely Yours, Sean Lui Sr. Staff Charging Compliance Engineer 3500 Deer Creek Road, Palo Alto, California US 94304 Phone: (650)681-5109 slui@teslamotors.com Tesla, Inc. 3500 Deer Creek Road, Palo Alto, CA 94304 p +650 681 5100 f +650 681 5101