TESOR PLUS CORP. TS5 SERIES - MFT USER MANUAL Touch-Screen Two Way Remote:TS1,TS4,TS5 One Way Remote :TX127 Two Way Transceiver:TR06CC,TR07CC,TR08CC,TR09CC,TR10CC Remote function table:
Remote command Buttons Arm Disarm Lock Unlock Silent Arm Silent Disarm Car finder Anti-hijack Panic Two stage unlock Shock bypass Activate Channel 1 Activate Channel 2 Activate Channel 3 Activate Channel 4 Activate Channel 5 Activate Channel 6 Remote engine start Remote engine shut Arm with engine down running hold 2 sec hold 2 sec / press times hold 2 sec hold 2 sec hold 2 sec 1 Key P1K1 P1K2 P1K1 P1K2 P0K1 P0K2 P1K1 P0K4 P0K4 P1K2 P1K1 P1K3 P1K1 P11K1 P11K2 P11K3 P11K4 P1K4 P1K4 P8K1 Conditions Ignition on Ignition on Arm state Ignition on Ignition off See function program See function program See function program See function program See function program See function program See function program Engine run (by ignition key) Outside view:
MAIN PAGE:
Press KEY to display Page 0: press anywhere in touch area to display PAGE ONE PAGE ONE:
2 Press Forward or Backward button display other page Other PAGES:
Button define is same as PAGE ONE,such as : P11K3 is CH5 button in p11 When transmitter received the car alarming will play trigger movies and sound voice:
The move will be stopped,if the key pressed Cancel count down: set count down =00:00 Cancel alert time: set alert time =00:00 Cancel PIN code: set PIN code =000000 3 Buttons Button in other page function table:
Key Explain Buttons P2K1 Set park time Set park position P2K2 P2K3 Set count down time P2K4 Clear trigger P3K1 Set alert time P3K2 Set time display Set VIBR. P3K3 Melody and key tone P3K4 Show DEMO P4K1 Set backlight P4K2 Set light delay Set currently time P4K3 P4K4 Set handset PIN Set currently car to 1st and set P6K1 code P6K2 P6K3 P6K4 car name Set currently car to 2nd and set car name Set currently car to 3rd and set car name Set currently car to 4th and set car name 4 Key P7K2 P7K3 P7K4 P8K1 P8K2 P8K4 P9K1 P9K2 P9K3 P9K4 P10K1 P10K2 Explain Set car loge in p0 Set English menu Set Spain menu Engine run Get vehicle battery volt Get the outside temperature Set daily start Set count down start time Power save on Power save off Silent arm key Silent disarm key P10K3 Arm without ZONE P10K4 car jack key 1. Arm Press button once, system will chirp once, parking lights flash once, lock the doors, starter disabled, window close output 1 sec. (if CH4 programmed), status LED start to flash slowly, will chirp 4 times and parking lights flash 4 times if door or hood or trunk isnt closed well while arming, and will not detect the door (hood, trunk) open until there are full closed well. The system can be triggered 5 second after armed if choosing off in program feature A-3. In other case see program feature table description. Shock sensor can be trigged after armed in program feature A-3. 2. Disarm Press button once, system will chirp and flash twice, unlock the door, turn on dome light, LED flash rapidly 30 sec. (if rearm function ON and off when door or trunk open or ignition turn ON). IF system was alarmed in arm mode (except warning zone of shock sensor) then if disarm siren chirps 4 times. IF system was alarmed in arm mode, Transmitter will chirp 4 times and show triggered detail record include trigger zone name, time, date. 3. Silent Arm Press button 4. SILENT DISARM
, system will arming without chirp. Press button
, system will disarm without chirp. 5. Alarm mode The siren will sound, parking lights flash 30 sec. if door or hood or trunk is opened or ignition key is turned on or triggered main zone of shock sensor. If trigged warning zone of shock sensor siren chirps 6 times. To stopping alarm press button Number of alarm hasnt to be more than 5 times for each zone. or
. 6. Trigger zone display 5 When system is alarming or after disarming, if the LED quick flashes several times and then 1 second pauses, it indicates the system has been triggered, and the times the LED flashes indicate the zone that was triggered, as below:
Twice: AUX 4 PIN 1 heavy trigger 3 times: AUX 4 PIN 2 heavy trigger 4 times: TRUNK 5 times: DOOR 6 times: HOOD 7 times: IGN 7. Arm without ZONE Press button build in shock sensor will be bypassed, other sensor is normal. Aux sensor 1 and sensor 2 will be bypassed, other sensor is normal.
, once to set arming, siren chirp, parking lights flash once, 8. Arm with engine running While engine is running and the key at ignition ON position press button lights flash, transmitter sounds. Then get out ignition key (engine goes on running! hand brake
, parking must be pull up). Press button will be running 15, 30, 45 or unlimited time period (according the program features F-3) then shut down and system. Shock sensor is bypassed at this period. system will chirp once, parking lights flash once. Engine Press button Engine also shut down when alarm. once to shut down engine. Parking flash once for confirm. 9. Auto rearm System will be rearm and relock if no any door (or trunk) opens or ignition key turn on within 30 seconds after disarmed. Its programmable function see program features B-1. 10. Passive arming / Arming reminder Ignition is off after driving, open the door, leave out and close it. the system will automatically armed after 30 sec. Passive arming still no lock door. Its programmable function see program features B-2 11. Immobilizer At immobilizer mode system automatically enter starter disable relay (w/o arm) after 30 sec from ignition turn off. At this mode LED flash when ignition ON. 12. Two-Stage unlock Press button will unlock drivers door only. Hold button for 2 seconds or press 6 twice (see program feature C-2), will unlock the passengers doors (activate button 2nd stage Unlock Output). If programmed. 13. Lock button will lock the doors. When system is disarmed and ignition key is on, press 14. Unlock When system is disarmed and ignition key is on, press button will unlock the drivers door. Hold button Output). 15. Lock / Unlock door upon ignition will unlock the passengers doors (activate 2nd stage Unlock If this function programmed (program feature A-2) cars doors lock automatically when ignition turn on and unlock when ignition turn off. 16. Car finder When system is armed, press button and parking lights flash 6 times. 17. Trunk release (Channel 1) simultaneously one time, siren will chirps 6 times Press and hold 2 sec. button shock sensors and trunk trigger will bypass until 10 sec after trunk closed. 18. Channel 2
, channel 31will active for 0.8 sec., When system armed for 2 seconds to activate channel 2. See programmable function (program Hold button feature C-2). 19. Channel 3 Press function (program feature C-3). to activate channel 3, remote Output pulse time of channel 3 is programmable 20. Channel 4 Press function (program feature C-4). to activate channel 4, remote Output pulse time of channel 4 is programmable 21. Channel 5 7 Press function (program feature D-1). to activate channel 5, remote Output pulse time of channel 5 is programmable 22. Channel 6 Press function (program feature D-2). to activate channel 6, remote Output pulse time of channel 6 is programmable 23. Panic In arm or disarm mode and ignition key is off. Press button siren will hold 2 sec ,system enter panic mode. System arm (with doors locking), sound and parking lights flash for 30 sec. Press button stopping alarm mode. (System stays at arm mode). or during 30 sec to 24. Anti-hijack mode Ignition must be ON and all doors closed. Press button anti-hijack mode. Parking lights flash once, LED start to flash rapidly.
, (or press override button once then open and close door) to activate To deactivate anti-hijack mode press button After 30 sec system enter arm with alarm modes, stopping alarm and disarm by transmitter is disable. To deactivate anti-hijack mode enter PIN-cod only or follow up override steps. or enter PIN-cod. 25. Valet mode At valet mode system can be remote door lock / unlock, activate channels. No any protect function. Enter and exit Valet mode procedure:
Be sure the system is disarmed. Turn the ignition key on. Press and hold the valet switch for 3 seconds. The siren will chirp once to enter valet or twice for exit. The LED will turn on solid indicating the system is in valet mode, or turn off indicating 26. Override Enter the vehicle Turn the ignition key on. Press and hold the valet switch for 3 seconds. The siren will stop sounding. The starter defeat is deactivated. 27. Pin code procedure 8 Pin-code consists of two digits. To disarm system with out remote transmitter or deactivate Anti-hijack mode use PIN-code procedure. Pin-code consists of two digits: X, Y. Factory default 1:1 (X=1, Y=1) To disarming:
- turn ignition ON
- press override button (X) times
- turn ignition OFF then ON
- press override button (Y) times
- turn ignition OFF After that system disarms. Note: System will automatically get out of PIN-code procedure if no pressing within 20 sec after last one. 28. PIN-code setting To change PIN-code:
- turn off ignition and the system is disarmed.
-Press the valet switch 4 times.
-Turn ignition on.
-The siren will chirp 4 times.
- press override button once
- siren chirps one time
- press button of transmitter to enter first digit of PIN-code:
- 1 ,
- 2,
- 3,
- 4
- siren confirm selecting digit ( 14 chirps)
- press override button once
- siren chirps two times
- press button of transmitter to enter second digit of PIN-code:
- 1 ,
- 2,
- 3,
- 4
- siren confirm selecting digit ( 14 chirps) After 20 sec or turning off ignition system will get out the PIN-code setting procedure, parking lights flash 4 times. 29. Manual arm Turn ignition off, press override button 3 times. Then open and close all doors. System auto arms in 10 sec with out door closing. If used manual arm mode and any zone triggered system turn alarm mode in 20 sec delay. 30. Turbo timer Turbo timer is programmable function (feature program F-2) 9 If function on:
- pull up hand brake while engine is running
- turn ignition key off and take out the key (engine is still running)
- engine will run for the programmed duration once. Parking flash once for confirm. To stopping engine press button 31. Mid-gear procedure (for manual gear only) If you are going to leave the vehicle the following procedure must be performed (It is need for safety engine auto start):
- ignition key is on, engine running
- pull up hand brake
- press and hold 2 sec. button
- turn ignition key off and take out the key (engine is still running)
- get out the vehicle and close the door
- after close the door, system shut down engine.
, parking lights flash once
- system shut down engine 1 minute later button arming (and door locking) by remote. pressing or immediately after This procedure must be performed each time before getting out the vehicle. Open door will cancel the setting. 32. Learn tachometer (RPM) turn off ignition Start the vehicle with the key. while the engine is running, the parking will flash. if dont,
- press override button 7 times
- turn on ignition
- parking lights flash and siren chirps 7 times
- press override button 6 times
- siren chirps 2 times please check tachometer wire connection. Press on transmitter to record the RPM. Chirp once to confirm. Press on transmitter to exit the RPM learn mode. chirp 4 times and flash 4 times 33. Remote engine start to remote engine start, parking light flash twice to confirm. Press and hold 2 sec. button If engine isnt started up from first, the system will automatically total start the engine 4 times. Cranking time (program feature E-2) of each next attempt will be increased by 0.2 sec. 10 once. Parking flash once for confirm. If start is successful. parking lights flash 3 times Engine runs during running time. Then shut down automatically. To stopping engine press button Engine auto start isnt available in case of:
When remote start is fall, siren chirps 4 times.
- engine is running
- hood is open
- hand brake isnt activated
- Mid-gear procedure isnt executed (for manual gear only) 34. Learning codes of remote transmitters There are only four transmitters may be learned in systems memory. Codes of learned remote transmitters will be erased each time the learning mode is activated. To activate leaning codes mode:
-Turn the ignition on, off, on, off and leave on. The siren will chirp.
-Press and hold the Valet/Override switch. The siren will chirp 3 times.
-Release the Valet/Override switch.
- press button of first remote transmitter
- siren chirps and remote transmitter beeps once
- press button
- siren chirps and remote transmitter beeps two times of second remote transmitter
- press button of third remote transmitter
- siren chirps and remote transmitter beeps 3 times of fourth remote transmitter
- press button
- siren chirps and remote transmitter beeps 4 times After 20 sec or turning off ignition system will get out the transmitter learning procedure, The siren will chirp 3 times. 11 35. Programming functions FEATURE A PROGRAMMING
- push the Valet Switch 1 times.
- turn off ignition
- press override button 3 times
- turn on ignition
- parking lights flash and siren chirps 3 times
- one long chirp with 1 short chirps is heard. You are now in the start feature A programming mode.
- press and release the transmitter button corresponding to the feature you want to program. Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. siren chirps when one chip arm, disarm LED 1 pulse Default setting 0.8 Second Door Lock &
Unlock siren no chirps two chip when arm, LED 2 pulse no chirps when disarm 3.5 Second Door Lock &
Unlock three chip LED 3 pulse four chip LED 4 pulse 0.8 Second Lock , 0.8 Second double Unlock 0.8 Second double Lock , 0.8 Second double Unlock Ign ON without lock, Ign OFF without unlock ARM no delay Ign ON with lock, Ign OFF with unlock ARM delay 15s Ign ON without lock, Ign OFF with unlock ARM delay 30s Ign ON with lock , Ign OFF without unlock ARM delay 45s 12 Press Transmitter A4 Button A1 A2 A3 FEATURE B PROGRAMMING
- push the Valet Switch 3 times.
- turn off ignition
- press override button 3 times
- turn on ignition
- parking lights flash and siren chirps 3 times
- one long chirp with 3 short chirps is heard. You are now in the start feature B programming mode.
- press and release the transmitter button corresponding to the feature you want to program. Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. Press Transmitter Button one chip LED 1 pulse Default setting Auto rearm off two chip LED 2 pulse three chip LED 3 pulse four chip LED 4 pulse Auto rearm on without lock Auto rearm on with lock passive arming off Passive arming on without lock Immobilizer mode off Immobilizer mode on Passive arming on with lock Anti-jack off Anti-jack on 13 B1 B2 B3 B4 FEATURE C PROGRAMMING
- push the Valet Switch 5 times.
- turn off ignition
- press override button 3 times
- turn on ignition
- parking lights flash and siren chirps 3 times
- one long chirp with 5 short chirps is heard. You are now in the start feature C programming mode.
- press and release the transmitter button corresponding to the feature you want to program. Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. Press Transmitter Button C1 C2 C3 one chip LED 1 pulse Default setting CH1 For trunk release each output 1s when active. CH2 for 2nd Unlock Hold button 2 2second to active CH3 For dome light two chip LED 2 pulse three chip LED 3 pulse four chip LED 4 pulse CH1 for channel output each output 30s when active. CH2 for 2nd Unlock Press button 2 2 times to active CH3 for channel output
= latched output and reset with IGN on CH1 for channel output
=latched output CH2 for OEM DISARM CH3 for channel output each output 1s when active. CH1 for channel output
= latched output and reset with IGN on CH2 for channel output each output 30s when active. CH3 for channel output each output 30s when active. 14 C4 CH4 For Car HORN output CH4 For window close Each output 1s , When arming . CH4 for OEM REARM CH4 for channel output each output 30s when active. Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. two chip LED 2 pulse three chip LED 3 pulse four chip LED 4 pulse FEATURE D PROGRAMMING
- push the Valet Switch 7 times.
- turn off ignition
- press override button 3 times
- turn on ignition
- parking lights flash and siren chirps 3 times
- one long chirp with 7 short chirps is heard. You are now in the start feature D programming mode.
- press and release the transmitter button corresponding to the feature you want to program. Press Transmitter Button D1 D2 D3 one chip LED 1 pulse Default setting CH5 For ACC output CH5 for channel output
=30s pulse CH6 For IGN3 output CH6 for channel output
=latched output Trunk pop no disarm Trunk pop with disarm 15 CH5 for channel output
= latched output and reset with IGN on CH6 for channel output
= latched output and reset with IGN on CH5 for channel output
=1s pulse CH6 for channel output
= 1s pulse D4 ENABLE Remote start and Engine Running as long as "+" or
"-" Brake input DISABLE Remote start and Engine Running as long as "+" or
"-" Brake input FEATURE E PROGRAMMING
- push the Valet Switch 9 times.
- turn off ignition
- press override button 3 times
- turn on ignition
- parking lights flash and siren chirps 3 times
- one long chirp with 9 short chirps is heard. You are now in the start feature E programming mode.
- press and release the transmitter button corresponding to the feature you want to program. Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. one chip LED 1 pulse Default setting Gasoline engine. The glow plug wire (diesel wait light) not use. two chip LED 2 pulse three chip LED 3 pulse four chip LED 4 pulse Diesel engine. 10 seconds warm-up timer The glow plug wire not use. Diesel engine. The glow plug wire must connect positive diesel wait light.
(max 120 sec.) Cranking time 3.6 s Diesel engine. The glow plug wire must connect negative diesel wait light.
(max 120 sec.) Push button start Cranking time 0.8 s Cranking time 1.8 s detects engine running by increasing low level of power voltage detects engine running by increasing hi level of power voltage detects engine running by RPM type detects engine running by GENERATOR 16 Press Transmitter Button E1 E2 E3 E4 Each time remote engine running 5 minutes Each time remote engine running 10 minutes Each time remote engine running 15 minutes Each time remote engine running 20 minutes FEATURE F PROGRAMMING
- push the Valet Switch 11 times.
- turn off ignition
- press override button 3 times
- turn on ignition
- parking lights flash and siren chirps 3 times
- one long chirp with 11 short chirps is heard. You are now in the start feature F programming mode.
- press and release the transmitter button corresponding to the feature you want to program. Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. Press Transmitter Button F1 F2 F3 F4 one chip LED 1 pulse Default setting ACC output When remote start success two chip LED 2 pulse three chip LED 3 pulse ACC output When hood temperature 50 ACC output When hood temperature 70 TURBO off Turbo timer 1 min. Turbo timer 3 min. four chip LED 4 pulse ACC output 5 min before engine shut down Turbo timer 6 min. Running time of Arm with engine running 15 min. Temperature-
control starting OFF Running time of Arm with engine running 30 min. Temperature-
control starting ON at -5 Running time of Arm with engine running 45 min. Temperature-
control starting ON at -10 Running time of Arm with engine running no limit. Temperature-
control starting ON at -20 17 RETURN TO FACTORY DEFAULT SETTING
- push the Valet Switch 13 times.
- turn off ignition
- press override button 3 times
- turn on ignition
- parking lights flash and siren chirps 3 times
- 3 long chirp is heard, You are now in the Return to factory default setting programming mode. Press and release the transmitter button confirm the system feature A,B,C&D programming all return to factory default setting.
, there will be a confirmation 1 short chirps to Press and release the transmitter button confirm the system feature E&F programming all return to factory default setting.
, there will be a confirmation 2 short chirps to Press and release the transmitter button confirm the system pin code return to factory default setting.
, there will be a confirmation 3 short chirps to Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. 36. Wires description 1 black loop for select type of gear not cut auto gear cut manual gear Set handset PIN code:
18 To check whether the PIN code is right or wrong, can press P1K2, P9K2 to check, if the PIN code is correct then can go to the next step. Before PIN code setting, need to check and see top right side of screen will show ***PIN, after entered the correct PIN code, will show *** 1ST on the top right side, means in the first entering status, after setting, will show ***2ND, second entering status, if same as the first setting will display SAVE the PIN code and return to P4, if not the same will display ERROR and return to P4, if lose the PIN code can read out through the data wire from PC. PIN code will be cancelled if set PIN code to 000000. 19 20 Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:
1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. 21