Your ekt has three parts:
The key unit (A), which holds the key ring;
The belt unit (B), which securely aaches to any belt or ulity belt
Key ring (C) sold separately
To aach belt unit to belt or ulity belt:
1 Place the metal clip inward, or to-
wards the users body, onto the top of the belt
2 Push down unl metal clip ts snug-
ly around the belt and belt is com-
pletely within metal clip
3 When secured, the metal clip should form a loop around the belt to prevent it from sliding up and o
To aach key unit to belt unit:
1 First make sure the key unit front is facing outward, or away from the users body, and that the key ring is at the boom of the key unit
2 Place the key unit down into the belt unit such that hole in the key unit mates with the hook on the inside of the belt unit
3 The key unit will then click and lock securely in place
To remove the key unit from the belt unit:
1. Grasp the keys with your hand; at the same me, using your thumb, press the top buon and pull keys up and away from the body
2. As the units separate, the strobe light on the key unit will ash one me indicang both units are acve and alarms are set If alarm signals check immediately, for begin matching serial numbers If they connue to signal, replace baeries
If problem persists, contact ekt customer support
To store the key unit in a key cabinet:
1. Remove the key unit from the belt
2. Aer the strobe light ashes, place the key unit in the docking staon
3. The key and belt units will then beep 3N indicang that the units are un-paired and ready for storage
4. The belt unit is turned o and is ready to receive any previously stored (un-paired) key unit
2 The key unit emits an 85 decibel audio alarm and a bright LED strobe light
All warning alarm signals connue unl the key unit is safely reaached to the belt unit
5. The key unit enters a low-power storage mode Upon removal, the user has 10 seconds to re-holster the key unit else its alarm will sound Upon successful re-holster, the key unit will beep two mes
6. A key unit that alarms because it was not re-holstered will reset itself aer 10 seconds of alarming
)=H 5EC=I If the key unit and the belt unit are sepa-
rated by more than 5 - 8 steps, four alarms will start:
1 The belt unit emits a strong vibra-
on and audible chirp alarm
4AF=?EC *=JJAHEAI Your ekt runs on two standard AAA baeries with an average life of $
months When 80 of baeries power is spent, a chirp alerts users that they need to be replaced It is recommended that you replace the baery in both the belt and key units at the same me to ensure connuity
Using a Phillips screwdriver, remove the screws on the back of the belt unit and back of the key unit Once the screws are removed, the baery doors will come o Replace baeries and screw the doors onto both units
6HK>AIDJEC 9=HECI This equipment generates, uses and can radiate radio frequency energy and if not used in accordance with the instruc-
ons, may cause harmful interference to radio or television recepon, which can be determined by turning the unit on and o The user is encouraged to aempt correcng the interference by increasing the separaon between the ekt units and the aected device or consult Tether Technologies for tech-
nical help
Refer to: hp:wwwaccessgpogov
naracfrcfr-retrievehtml#page1 Title "% CFR; Part 15, 5econ 105 Cauon: Changes or modicaons to ekts RF hardware that are not eNpress-
ly approved by Tether Technologies, Inc
could void both the users authority to operate the equipment and the product warranty
61+-5 . +21)+-
This device complies with part 15 of the FCC Rules Operaon is subect to the following two condions: (1) This device may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, interference that may cause undesired operaon
including This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protec-
on against harmful interference in a residenal commercial use environ-
ment FCC ID labels are located inside the baery compartments of both units
2H@K?J 9=HH=JO 5KFFHJ Your ekt v2 is covered by a limited war-
ranty To be eligible, you must register your ekt within 30 days of purchase at wwwstopkeylosscomsupport In brief:
The warranty covers any defects or mal-
funcons in your new ekt and lasts for a for a period of 90 days from the date of purchase
Tether Technologies will replace any defecve or malfunconing part or if the unit is determined to be non-repairable, provide you with a replacement ekt, all at no charge
Baeries, or any problem that is caused by abuse, misuse, or an act of God (such as a ood) are not covered Also, conse-
quenal and incidental damages are not recoverable 5ome states do not allow the eNclusion or limitaon of incidental or consequenal damages, so the above limitaon or eNclusion may not apply to you
7IAH =K=
Electronic Key Tether www.StopKAyLoII.com