SPECIFICATION Bluetooth SpecificationsBluetooth version 4.1 Support profile: A2DP Transmission distance: up to 2 m (This may vary based on environmental factors or the type of Bluetooth device being used) Built-in battery: 55 mAh Lithium battery USB Recharge voltage: DC 5V/500mA Output power: 16mW Frequency Response: 20Hz - 20KHz Transmission Response: 2.4GHz - 2.48 GHz PACKING Bluetooth Earbuds Silicone Earbud Covers USB Charging Cable Travel Case and Carabiner User Manual Overview BLUETOOTH OPERATION FCCID: 2AGR43260B IC ID: 21530-3260B Spectrum Bluetooth Earbuds Vol + / Previous On/ Off Pause / replay Answer / Hang up Vol - / Next User Manual R Microphone Recharging Port 1. Please ensure that the Bluetooth function has been turned on in the settings of your Bluetooth enabled device. 2. Turn the earbuds on by pressing the power button for 4 seconds. The indicator light will flash to detect Bluetooth enabled devices near you and will enter pairing mode. When pairing, remain within 3 feet of the earbuds. The indicator light will go off if no Bluetooth devices are detected within 5 minutes. 3. GEMLINE EB will appear on the Bluetooth device list, select GEMLINE EB to establish pairing. If instructed to enter a PIN code, please enter 0000. 4. Once the earbuds have been paired to the desired mobile device, the indicator light will turn blue to confirm successful pairing. 5. When you want to play audio from another Bluetooth device, disconnect the earbuds from the original device and follow steps 1-3 to re-pair the earbuds with a new Bluetooth enabled device. Back Cover Front Cover page 02 page 03 BUTTON CONTROL Pause / Play: Press the On/Off button once to pause the music, press again to play. On / Off: Press and hold the On/Off button to control the power of the earbuds. Vol + / Previous: Press and hold the + button for 2 seconds for the previous track. Press once to increase the volume. Vol - / Next: Press and hold the button for 2 seconds for the next track. Press once to reduce the volume. Hands-free: Press On/Off button once to answer an incoming call. While on a call, press On/Off once to end the call. Redial last call: Press On/Off button twice to redial last number dialed on the connected mobile device. CHARGING THE EARBUDS 1. When the battery is low, please charge via the included USB cable. The charging time is approximately 1-1.5 hours and provides up to 2 hours of continuous operation. Standby time is approximately 60 hours. 2. The LED indicator light will be red during charging and will turn blue once it is fully charged. WARNING 1. Do not disassemble, repair, or modify the earbuds. 2. Do not place product in or near fire to avoid danger, as it uses a lithium battery. 3. Avoid storage at extreme temperatures, this can shorten the battery life and may affect the earbuds. 4. Keep the earbuds dry and do not store the earbuds in damp areas to avoid damage to the earbuds. 5. Avoid dropping the earbuds as it may damage the product. KIND REMINDER 1. To prolong the earbuds life span and to avoid hearing damage, please do not listen to music under high volume for long periods of time. 2. When an error occurs with the earbuds, please turn off the earbuds and restart it to troubleshoot. 3. When the earbuds power is low, the Bluetooth range may be affected. Please charge the earbuds to avoid disruptions during use. The sound is low or distorted The Bluetooth indicator light remains OFF 1. Inspect the volume of the connected earbuds or Bluetooth enabled device and adjust the volume as needed. 2. The power of the battery is insufficient, please recharge the earbuds. 1. The power of the battery is insufficient, please recharge the earbuds. 2. Restart the earbuds. Unable to pair the earbuds with a mobile device 1. Inspect whether the earbuds is searching for a Bluetooth enabled device to connect to. If not, restart the earbuds. 2. Difficulty in searching and connecting to a desired device can be affected if multiple devices are equipped, turned on, and in range for Bluetooth connectivity. Please turn off or disable the Bluetooth function on the other devices. 3. The power of the battery is insufficient, please recharge the earbuds. 1. Inspect the distance between the earbuds and the Bluetooth enabled device, it may exceed the Bluetooth transmission range. 2. Inspect if there is an obstacle between the earbuds and the Bluetooth enabled device. 3. The power of the battery is insufficient, please recharge the earbuds. page 04 page 05 page 06 page 07 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre lefonctionnement.