FCC ID: B8Q4BTX 4 Button Transmitter

Residential Style Transmitters Current Production Openers STEP 1: PLACE CURRENT PRODUCTION RESIDENTIAL OPENER INTO PROGRAMMING MODE STEP 1: PLACE COMMERCIAL OPENER INTO PROGRAMMING MODE NOTE: The openers LEARN MODE will time out in 30 seconds. Programming must be completed within 30 seconds. Adding a SINGLE (1-2-3-4 Button) Transmitter 1. 41360.00092, 02/20 Commercial Style Transmitters PROGRAMMING ASSISTANCE:

If the opener does not activate after the steps shown, repeat steps or contact Customer Care by website chat

(www.geniecompany.com) or by phone at: 1-800-354-3643 for programming assistance. You may also scan this QR code for additional information and links. Changing the Battery:

1. Remove vispr clip. 2. Remove small phillips head backing screw. 3. Pry case open with small coin or screwdriver. 4. Remove circuit board. 5. Replace battery with CR2032 coin cell. 2. 3. 4. 5. 2. 3. 4. 5. If operator is in RUN mode, press CAL/RUN key to enter calibration mode. Press SCROLL (up or down) until display reads LEARN NEW XMTR?

Fig.1 This question along with the instruction HIT SET FOR YES will continuously pan across the display window. (Pressing SCROLL or CAL/RUN will cancel the operation.) Press SET/CLEAR . Display will read PUSH XMTR BUTTON TWO TIMES TO LEARN XMTR. Press Transmitter button two times. The display will read XMTR ___LEARNED. Where it assigns a random number to the transmitter. That transmitter is entered and ready to operate the door.

(Label the transmitter with this number.) LEARN NEW XMTR?

OPEN CLOSE Press SCROLL (up or down) to move on to another menu item, or CAL/RUN to exit the CAL mode. CAL RUN SET CLEAR SCROLL SCROLL Fig. 1 STEP 1: PLACE COMMERCIAL OPENER INTO PROGRAMMING MODE Adding a Single (OPEN/CLOSE/STOP) Transmitter 1. If operator is in RUN mode, press CAL/RUN key to enter calibration mode. Press SCROLL (up or down) until display reads LEARN NEW XMTR?

Fig.1 This question along with the instruction HIT SET FOR YES will continuously pan across the display window. (Pressing SCROLL or CAL/RUN will cancel the operation.) Press SET/CLEAR . Display will read PUSH XMTR BUTTON TWO TIMES TO LEARN XMTR. Press OPEN Transmitter button two times. The display will read XMTR ___LEARNED. Where it assigns a random number to the transmitter. That transmitter is entered and ready to operate the door.

(Label the transmitter with this number.) LEARN NEW XMTR?

OPEN CLOSE Press SCROLL (up or down) to move on to another menu item, or CAL/RUN to exit the CAL mode. CAL RUN SET CLEAR SCROLL SCROLL Fig. 1 STOP STOP PRGM SET

PRGM PRGM PRGM SET SET SET TYPE 1 TYPE 2 TYPE 3 There are 4 types of programming button pads. Type 1 is shown TYPE 4 in these steps. All buttons perform the same function and programming is the same for all types shown above. Place operator into programming mode: TYPE 1-2-3-4 1. Press and hold the program button until the round LED turns blue, then release. PROGRAM PROGRAM SET

SET

2. The round LED will go out and the long LED will begin flashing purple. 3. Proceed to STEP 2. 4. Press desired remote control button 3 times slowly until door operates. PROGRAM PROGRAM SET

SET

STEP 1: PLACE OLDER STYLE RESIDENTIAL OPENER OR EXTERNAL RECEIVER INTO PROGRAMMING MODE Openers manufactured between 1995 to 2011 and all external receivers. (LEARN CODE TYPE) NOTE: Learn Code Buttons are normally located under lens covers on earlier models. Place opener into programming mode:

1. Press LEARN CODE button until RED LED begins to blink 2. Press desired remote control button 3 times or until door then release. operates. RADIO SIGNAL LEARN CODE RADIO SIGNAL LEARN CODE or OPEN SET SET LEARN MANUAL LIMIT FORCE CODE CLOSE LEARN CODE RADIO SIGNAL LEARN CODE Pull protective tab to activate remote

WARNING Moving Door can cause serious injury or death. Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving parts. Keep people clear of opening while door is moving. DO NOT allow children to play with the remote or door opener. If SAFETY REVERSE does not work properly:

Close door then disconnect opener using the manual release handle. Refer to Door and Door Openers Owners Manuals before attempting any repairs.

AVERTISSEMENT UNE PORTE EN MOUVEMENT PEUT CAUSER DE GRAVES BLESSURES, VOIRE LA MORT. Ninstallez PAS le transmetteur moins que lappareil de scurit du dispositif de fermeture de porte ne fonctionne conformment au manuel du dispositif de fermeture de porte. La console murale doit tre monte la vue de la porte, au moins 5 pieds au-dessus du sol et il ne doit y avoir aucune pice de porte en mouvement proximit. loignez les gens de louverture lorsque la porte est en mouvement. NE permettez PAS aux enfants de jouer avec le transmetteur ou le dispositif de fermeture de porte. Si linversion de scurit ne fonctionne pas correctement :

Fermez la porte, puis dconnectez le dispositif douverture laide de la poigne de dgagement manuel. Nutilisez PAS le transmetteur ni le dispositif de fermeture de porte. Rfrez-vous aux manuels du propritaire de la porte et de louvre-

porte avant de tenter toute rparation. For Patent Information: www.geniecompany.com/patent, 2020, The Genie Company FCC Part 15.21 Statement:

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC / IC Statement:

This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

8 7 6 5 4 3 1 NOTES: (UNLESS OTHERWISE SPECIFIED) 1. BLACK GRAPHICS AND TYPE ON 2 MIL MYLAR WITH PRESSURE SENSITIVE PERMANENT ADHESIVE FOR USE ON ABS PLASTIC, 1 MIL CLEAR MYLAR OVERLAY. 2. D CLEAN, COLOR PER ANSI Z535.1. 25.40 ORANGE BACKGROUND WHITE BACKGROUND 2 REVISIONS DESCRIPTION PRELIMINARY ADDED SPECIFIC FCC ID AND IC DATA BY MODEL NUMBER TO CHART. REVISED FCC ID AND INDUSTRY CANADA CHART DATA. GCO REV

01 02 03 DATE APPROVAL 03/20/2020 RSM 05/20/2020 RSM 06/17/2020 RSM D C B MODEL NUMBER (SEE TABLE) FCC ID DATA (SEE TABLE) INDUSTRY CANADA DATA (SEE TABLE) COMPANY NAME (SEE TABLE) R0.76 MODEL NUMBER (SEE TABLE) FCC ID DATA (SEE TABLE) INDUSTRY CANADA DATA (SEE TABLE) COMPANY NAME (SEE TABLE) 41428P 41428N 41428M 41428L 41428K 41428J 41428H 41428G 41428F 41428E 41428D 41428C 41428B 41428A OOCS-P O4BT-P O3BT-P O2BT-P O1BT-P GOCS-P G4BT-P G3BT-P G2BT-P G1BT-P G4BT-R G3BT-R G2BT-R G1BT-R B8QOCSTX B8Q4BTX B8Q3BTX B8Q2BTX B8Q1BTX B8QOCSTX B8Q4BTX B8Q3BTX B8Q2BTX B8Q1BTX B8Q4BTX B8Q3BTX B8Q2BTX B8Q1BTX 2133A-OCSTX OVERHEAD DOOR CORPORATION 2133A-4BTX OVERHEAD DOOR CORPORATION OVERHEAD DOOR CORPORATION 2133A-3BTX OVERHEAD DOOR CORPORATION 2133A-2BTX 2133A-1BTX OVERHEAD DOOR CORPORATION 2133A-OCSTX 2133A-4BTX 2133A-3BTX 2133A-2BTX 2133A-1BTX 2133A-4BTX 2133A-3BTX 2133A-2BTX 2133A-1BTX THE GENIE COMPANY THE GENIE COMPANY THE GENIE COMPANY THE GENIE COMPANY THE GENIE COMPANY THE GENIE COMPANY THE GENIE COMPANY THE GENIE COMPANY THE GENIE COMPANY PART NUMBER MODEL NUMBER FCC ID DATA INDUSTRY CANADA DATA COMPANY NAME PLOTTED: -

THE DRAWINGS AND ALL OTHER INFORMATION CONTAINED HEREIN ARE THE CONFIDENTIAL PROPRIETARY PROPERTY OF OVERHEAD DOOR CORPORATION, INCLUDING ITS AFFILIATED SUBSIDIARIES AND AFFILIATES. THIS DRAWING INFORMATION, IN WHOLE OR IN PART, MAY NOT BE COPIED IN ANY MANNER OR DISCLOSED TO ANYONE WITHOUT PRIOR WRITTEN CONSENT OF OVERHEAD DOOR CORPORATION. DISCLOSURE OF ANY DRAWING OR INFORMATION IS INTENDED NOT TO AND SHALL NOT OPERATE AS A LICENSE OR AUTHORIZATION TO USE IT FOR ANY PURPOSE WITHOUT SPECIFIC WRITTEN CONSENT OF OVERHEAD DOOR CORPORATION. UNLESS OTHERWISE SPECIFIED INTERPRET DIMS & TOLS PER ASME Y14.5M ALL DIMS ARE IN MILLIMETERS DO NOT SCALE TOLERANCES:

.X = .25

.XX = .12

.XXX = .06 ANGULAR = 1 DRAWN CHECKED APPROVED MATERIAL APPROVALS DATE RSM 3/13/2020 SEE NOTE #1 DIMS AND SPECIFICATIONS CIRCLED WITH SYMBOL

' ARE CRITICAL TO QUALITY DESIGN FEATURES

& MUST MEET APPLICABLE IN-PROCESS INSPECTION STANDARDS. HOLES:

< 6.5 = +.10 / -.08 6.5-13 = +.15 / -.08

> 13 = +.20 / -.08 ALL GEOMETRY GOVERNED BY 3D CAD DATABASE:

FINISH 41428 SEE NOTE #2 3 A SUBSIDIARY OF OVERHEAD DOOR CORPORATION MT. HOPE, OHIO DESCRIPTION LABEL,FCC/IC,RCR XMTR, A SIZE B DRAWING NUMBER 41428 SCALE 6:1 2 SHEET 1 OF 1 1 7 6 5 4 3.76 9.53 C B A THIRD ANGLE PROJECTION ENG F.20.041B-(FORM REV A) 8

Genie Company P. O. Box 67 Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, Illinois 60515 Attn: Director of Certification FCC ID: B8Q1BTX, B8Q2BTX, B8Q3BTX, B8Q4BTX, B8QOCSTX Authority to Act as Agent FCC On our behalf, I appoint Rick King, of Elite Electronic Engineering, Inc. at 1516 Centre Circle, Downers Grove, Illinois 60515 to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Elite Electronic Engineering, Inc., still resides with The Genie Company, P.O. Box 67 Mt. Hope, OH 44660. Dated this 28th Day of April 2020 Agency agreement expiration date:

July 22, 2020 By:

Signature Title: Sr. RF Engineer Mike Whitley Printed Name On behalf of :

The Genie Company a Division of Overhead Door Corporation Telephone:

214-593-0042

Genie Company P. O. Box 67 Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, Illinois 60515-1082 FCC ID: B8Q1BTX, B8Q2BTX, B8Q3BTX, B8Q4BTX, B8QTX Product Name: 315390T4 Transmitter Model: G1BT-P, G2BT-P, G3BT-P, G4BT-P, GOCS-P, G1BT-R, G2BT-R, G3BT-R, G4BT-R, O1BT-P, O2BT-P, O3BT-P, O4BT-P, OOCS-P Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

Electrical Schematics, Layout Drawings, and Bills of Materials Theory of Operation Documentation / Technical Description PCB Assembly and Block Diagram These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 24th Day of March 2020 By:

Signature Title: Sr. RF Engineer Mike Whitey Printed On behalf of :

The Genie Company a Division of Overhead Door Corporation Telephone:

830-660-0800