If your Door Opener has a black Antenna Wire, the Learn Code Button and Indicator LED are located near the Antenna. Red Indicator LED
(The Light Lens may need to be opened.) seated
- If your Door Opener does not ae have an Antenna, you have an External Receiver. The External Receiver cover must be removed to access me ae the Learn Code Button Button and Indicator LED.
+ Press the Learn Code Button. Learn Code Indicator LED (on Opener) will blink. Enter your PIN and press ED on Keypad. Learn Code Indicator LED stays on.
* Press again. Learn Code Indicator LED turns off. Wait until Keypad Backlight turns off (approximately 30 seconds).
| Step 3: | OPERATING ONE Door OPENER A Tomove the Garage Door.
* Enter your PIN. NOTE
+ Ifthe Door does not move, check the red LED on Keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking, re-enter your PIN and try again.
+ Any Keypad Button will control the Door for 30 seconds after the Door starts moving.
+ Rapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over. Proceed to Section 3 - Mounting Instructions. For answers to questions, call 1-800-35 GENIE, or visit www.geniecompany.com Additional Genie products can be ordered using the Accessories page in your Owner's Manual or through the 800 number above. 2003 The Genie Company, D.B.A. GMI Holdings, Inc.
* Press (
again. Red LED blinks - twice per second,
* Press the number of Doors (total) you wish fi Red LED blinks several times and turns off.
| Step 3: | ProcRAMMING Door OPENERS A Decide which Door will be Door #1,#2 and #3.
* Press the Learn Code Button (see Section 1 Step 2). Learn Code Indicator LED (on Opener) blinks. on Keypad. Learn Code Indicator LED stays on.
* Enter your PIN and press
* Press the number you have picked for this Door Opener ((
Learn Code Indicator LED stays on.
* Press Learn Code Indicator LED turns off. B_ Repeat step A above for each Door Opener. Each Door Opener must be programmed to receive the signal from the Wireless Keypad. Wait until Keypad Backlight turns off (approximately 30 seconds). Ezz OPERATING 2 OR 3 Door OPENERS A Tomove one of the Doors.
+ Enter your PIN.
* Press
* Press Door Opener number @ or SEE NOTE AT BOTTOM OF SECTION 1 Proceed to Section 3 - Mounting Instructions. a ee ee a a ee Gece eal OR CHANGING Your PIN A Erase old PIN.
+ Press and hold in order -
Red link once and turn off.
* Release all buttons. wi B_ Programming Door Opener(s).
* Return toProgramming (Section 1 or Section 2). USP Eee aad |
A temporary PIN allows temporary access to your home by repair persons, meter readers, etc. if you so desire. A Enter your PIN. NOTE
* DONOT reprogram the Door Openers).
* Temporary PIN remains active until the next time your normal PIN is entered. Pp @
If the red LED does Figure 2 e0 not blink during use, the battery needsto | Red LED ||l@@
be changed. OSI Bottom Covers available in:
* Brown - P/N 35365R
+ Almond - P/N 353655 Mounting Screw
<3 Press here
+ Sandstone - P/N 35365T FCC and IC CERTIFIED This vce complies wh Pat 5 and 85210 o dusty Canada Ts equipment ha een ested and fund teomplt wah nels ora Clssb lal dence pusant ta the Fc hues Theses re eda ei ean al gale hrnfditeference ha etna hstelabon Ts 1d can raat radiofrequency energy and, if not installed and used in accordance wath the instuctons may cause haul interference to ado conmunications However there no guarantee that interference will not occur in a particular instalation. this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off anon the user is ry to correct the interference by one ot more of the following measures: 1.Re-orient or iver antenna. 2. Increase the separation bet opener and receiver. 3.Connect the opener into an outlet on a circuit iffrent from that to which the appliances connected. 4, Consult the dealer, Changes or modifications nat expressly approved by the manufacturer could void the user authority to operate the equipment Printed in the U.S.A.