LED Flashlight Remote WARNING
!
MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT install transmitter unless the door operators safety device works as required by the door operators manual. Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts. Keep people clear of opening while door is moving. DO NOT allow children to play with the transmitter or door operator. If safety reverse does not work properly:
Close door then disconnect opener using the manual release handle. DO NOT use transmitter or door operator. Refer to Door and Door Opener Owners Manuals before attempting any repairs.
!
AVERTISSEMENT DMNAGEMENT PORTE PEUT CAUSER DES BLESSURES GRAVES OU LA MORT. NE PAS installer le transmetteur moins que le dispositif de scurit de loprateur de porte ne fonctionne comme lexige le manuel dutilisation de la porte. Console murale doit tre mont en vue de la porte dau moins 5 pieds au-dessus-de-chausse et claire des pices mobiles de la porte. Garder les personnes clair de louverture lorsque la porte est en mouvement. Ne pas laisser les enfants jouer le premier match distance ou la porte. Si la scurit inverse ne fonctionne pas correctement:
Fermer la porte, puis dbranchez moteur laide de la poigne de dverrouillage manuel. Ne pas utiliser douverture distance ou la porte. Reportez-vous la porte et ouvre-porte de propritaires manuels avant de tenter toute rparation. 1 Putting Opener into Programming Mode New Genie Openers PRGM SET TYPE 1 TYPE 2 TYPE 3 There are 3 types of programming button pads. Type 1 is shown in these steps. All buttons perform the same function and programming is the same for all types shown above. Place operator into programming mode: TYPE 1-2-3 1. Press and hold the program button until the round LED turns blue, then release. 2. The round LED will go out and the long LED will begin flashing purple. PROGRAM SET PROGRAM SET
+
+
PROGRAM SET PROGRAM SET
+
+
-OR-
Genie openers and external receivers manufactured between 1995 to 2011 Place operator into programming mode:
1. Press & release Learn Code button once. The red LED will begin to flash. RADIO SIGNAL LEARN CODE RADIO SIGNAL LEARN CODE or OPEN SET LEARN MANUAL LIMIT FORCE SET CODE CLOSE LEARN CODE RADIO SIGNAL LEARN CODE Proceed to step 2 2 Programming a Remote to the Opener NOTE: Once in programming mode, you will have approximately 30 seconds to perform this step. Note: While programing remote buttons, stand at least 5 feet away from the opener. This ensures you have proper communication between the remote and the opener. Flashlight Button Remote Buttons 1. Slowly press and release the remote button of your choice two times. The opener LEDs will flash and go off, indicating you have successfully programmed your remote.
+
+
PROGRAM SET PROGRAM SET
- OR -
RADIO SIGNAL LEARN CODE 2. Press and release the same button a third time and door will open or close. NOTE: It is possible to press the remote button too quickly or lightly. If the LEDs do not go OFF, press the remote button several more times to achieve confirmation. r e u m b t n a d p e N e r 111222501234, 11/2016 Proceed to step 2 or see alternate programming (top right) 3 Lost or Stolen Remote/Erasing all Remotes Replace the Battery This pertains to all button pad TYPES shown in section 1 New Genie Openers PROGRAM PROGRAM Replace remote battery with 1-AAA battery. 1. Press down on top of battery door and slide back off of remote. 1. Press and hold the program button until the round LED turns blue, then release. 2. Press and hold the Up(+) Down (-) buttons at the same time, until the both LEDs flash blue and go OFF.
-OR-
SET
+
SET
+
2. Match battery polarity symbols inside battery housing and replace battery. PROGRAM SET
+
3. Align cover and snap case closed. Genie openers and external receivers manufactured between 1995 to 2011. To erase all remote devices from all other types of Genie openers, Press and hold the Learn Code Button until the LED stops blinking. A A A RADIO SIGNAL LEARN CODE RADIO SIGNAL LEARN CODE Start at section 1 to reprogram your remotes. NOTE: Clearing remote control memory from the power head will clear ALL programmed remotes and wireless keypads. Your opener will no longer recognize any signal from any remote device, including a missing remote device. 4 Using the LED Flashlight Press the LED Flashlight button once. LED Flashlight will operate until button is pressed again or when 4 minutes have passed. After 4 minutes the LED will flash indicating that light will turn off automatically. For additional help or information, please visit our website at www.GenieCompany.com, contact our Customer Care group at 1-800-35-Genie, or write to us directly at:
GMI Holdings INC. d/b/a The Genie Company One Door Drive, PO Box 67 Mount Hope, Ohio 44660 FCC Part 15.21 Statement:
Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. 2016 GMI Holdings, Inc. DBA The Genie Company