FCC ID: B8Q-UKEP Universal Keypad Transmitter

1234504392, 11/2019 Keypad Overview ProgramKey LED Keypad Up/DownKey

(enter) LEDOff LEDOn LEDFlashing KeypadOff KeypadOn KeypadFlashing Activate keypad by opening battery compartment and pull protective tab. Reinstall compartment door to begin programming. TAB SAVE THESE INSTRUCTIONS FOR FUTURE USE Universal Wireless Keypad Instructions Scan this code with a QR code reader app on a smart device to view a video of these instructions or visit www.geniecompany.com Find the model of the garage door opener(s) that this keypad will be operating from the chart below. Mark down the pertinent information in the section below this chart. ID BRAND-TYPE F R E Q -

TYPE DESCRIPTION MHz I N S T R Group Genie Intellicode 1 315,390 Genie Intellicode and OHD Mfg from 1995 to present STEP 1-A) DETERMINE THE DOOR OPENER BRAND AND TYPE STEP 1-B) DETERMINE DOOR CODE FOR FIXED CODE OPENERS What do fixed code dip switches look like and how do I convert them to button presses on my new universal remote?

If the opener has a group of 9 switches with 3 positions per switch (TRINARY):

Switch in the UP position = Press button 1 Switch in the MIDDLE position = Press button 2 Switch in the DOWN position = Press button 4 1 2 3 4 5 6 7 8 9 In this example, the button presses would be:

4 1 2 1 4 1 1 1 2 If the opener has a group of 9-12 switches with 2 positions per switch (BINARY):

1 2 3 4 5 6 7 8 9 10 11 12 Switch in the UP position = Press button 1 Switch in the DOWN position = Press button 4 In this example, the button presses would be:

4 1 1 1 4 1 1 1 1 4 4 4

0

Genie Intellicode 2 315,390 Genie Intellicode and OHD Mfg from 2011-2012 <what else?>

STEP 1: Each shaded box below represents a DIP switch position. In these boxes, write in the number 1, 2 or 4 as it corresponds to the UP, MIDDLE or DOWN switch position you see on the remote, opener head or receiver.

WARNING MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT install transmitter (keypad) unless the door operators safety device works as required by the door operators manual. Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts. Keep people clear of opening while door is moving. DO NOT allow children to play with the transmitter or door If safety reverse does not work properly:

Close door then disconnect opener using the manual release operator. handle. DO NOT use transmitter or door operator. Refer to Door and Door Opener Owners Manuals before attempting any repairs.

AVERTISSEMENT DMNAGEMENT PORTE PEUT CAUSER DES BLESSURES GRAVES OU LA MORT. NE PAS installer le transmetteur (clavier) moins que le dispositif de scurit de loprateur de porte ne fonctionne comme lexige le manuel dutilisation de la porte. Console murale doit tre mont en vue de la porte dau moins 5 pieds au-dessus-de-chausse et claire des pices mobiles de la porte. Garder les personnes clair de louverture lorsque la porte est en mouvement. porte. Ne pas laisser les enfants jouer le premier match distance ou la Si la scurit inverse ne fonctionne pas correctement:

Fermer la porte, puis dbranchez moteur laide de la poigne de dverrouillage manuel. Ne pas utiliser douverture distance ou la porte. Reportez-vous la porte et ouvre-porte de propritaires manuels avant de tenter toute rparation. 315 390 390 390 310 318 372.5 372.5 303 315 Rolling Rolling Rolling Rolling Rolling Rolling Rolling Fixed-

Learn Rolling Rolling Fixed-

Learn Fixed-

Learn 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Chamberlain

(Purple) Chamberlain

(Orange/Red) Chamberlain

(Yellow) Chamberlain

(Green) Sommer Linear Wayne Dalton Ryobi Guardian Marantec FUTURE reserve FUTURE reserve FUTURE reserve FUTURE reserve FUTURE reserve FUTURE reserve FUTURE reserve Genie - 12 switch binary Genie - 9 switch binary Stanley - 10 switch binary 390 390 310 FUTURE reserve FUTURE reserve FAAC 433.92 Rolling 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic, and Do It GDO mfg from 2005 to present (purple button) Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic, and Do It GDO mfg from 1997-2004 (orange/red button) Chamberlain, Sears Craftsman, and LiftMaster GDO mfg from 2011 to present (yellow button) Chamberlain, Sears Craftsman, LiftMaster, Master Mechanic, and Do It GDO mfg from 1993-1996 (green button)

<need details>

Linear GDO mfg from 1997 to present Wayne Dalton GDO mfg from 1999 to present Ryobi GOD mfg from 2016 to present <correct?>

Guardian and Xtreme GDO mfg from 199x to present <dates? Want others listed, like Boss, Decko, etc?>

Marantec GDO mfg from 199x to present <dates?>

DOOR #1 Convert the 9 switch code:

Convert the 12 switch code:

DOOR #2 Convert the 9 switch code:

Convert the 12 switch code:

DOOR #3 Convert the 9 switch code:

Convert the 12 switch code:

It is recommended to complete programming before mounting keypad Keypad LEDs Successful Entries Failed Entries Fixed-Dip 12 DIP switch Genie GDO Fixed-Dip 9 DIP switch Genie GDO Fixed-Dip 10 switch Stanley and Moore-O-Matic GDO BOX A:

Opener ID - DOOR #1: __________________ Opener ID - DOOR #2: __________________ Opener ID - DOOR #3: __________________ BOX B:

Fixed Code Switch ID - DOOR #1: __ - __ - __ - __ Fixed Code Switch ID - DOOR #2: __ - __ - __ - __ Fixed Code Switch ID - DOOR #3: __ - __ - __ - __ PROGRAMMING STEP 2 - SETTING A PERSONAL PIN NUMBER:

1. Enter a personal PIN. (3-8 digits) 2. Press UP/DOWN key once. (LED will turn solid indicating keypad is ready for opener ID) Keypad LED will flash and beep each time a key is pressed and entry is accepted. Keypad LED and PROGRAM key will flash slowly and number pad back light will remain on for 15 seconds indicating a successful program or valid PIN has been entered. Keypad LED, PROGRAM key and number pad back light will flash rapidly indicating a problem with programming or an invalid PIN entry. Press the 7 & 9 keys together 3 times to start over. STEP 3 - PROGRAMMING THE KEYPAD - Section A = Learn Type, Section B = Fixed Code Type PLACING OPENER INTO LEARN MODE STEP 4) OPERATING THE KEYPAD WITH THE OPENER(S) This keypad can be used with, up to, 3 different brands and types of garage door openers in any combination. Use the steps below to program each of the 3 doors independently. EXAMPLE:

Door #1 is a Genie brand Intellicode opener. Use section A - Program Door # 1 Door #2 is a LiftMaster Purple Learn button type. Use Section A - Program Door # 2 Door #3 is an Overhead Door brand 9 switch trinary type. Use Section B - Program Door #3 SECTION A - PROGRAMMING THE KEYPAD FOR LEARN CODE TYPE OPENERS:

Program Door #1:

1. Enter the OPENER ID written in BOX A - DOOR #1. 2. Press the UP/DOWN key. (LED will go out) 3. Enter PIN. 4. Press UP/DOWN key. 5. Place opener into LEARN MODE. (See placing opener into learn mode section or openers instruction manual for remote programming 6. Enter PIN. 7. Press UP/DOWN key 3 times. Opener #1 will operate. Program Door #2:

1. Press PGRM button two times. 1. Enter the OPENER ID written in BOX A - DOOR #2. 2. Press the UP/DOWN key. (LED will go out) 3. Enter PIN. 4. Press UP/DOWN key. 5. Place opener into LEARN MODE. (See placing opener into learn mode section or openers instruction manual for remote programming instruction) instruction) 6. Enter PIN. 7. Press UP/DOWN key 3 times. Opener #2 will operate. Program Door #3:

1. Press PGRM button 3 times. 1. Enter the OPENER ID written in BOX A - DOOR #3. 2. Press the UP/DOWN key. (LED will go out) 3. Enter PIN. 4. Press UP/DOWN key. 5. Place opener into LEARN MODE. (See placing opener into learn mode section or openers instruction manual for remote programming Find the LEARN/PGRM button on the garage door opener or external receiver - shape, color or name of this button could vary by brand. Most garage door openers LEARN/PGRM buttons are located under the light covers. For commercial or gate openers, this button may be on the circuit board of the opener. In some cases, this button could also be on an external receiver that is mounted on or nearby the product. Consult the devices manual if needed. Single Door Operation:

1. Ensure number pad back lighting is off. 2. Enter PIN. 3. Press the UP/DOWN key. 4. Opener will operate. PRGM EXAMPLES:

SET RADIO SIGNAL LEARN CODE Gate Recievers LEARN CODE Multi-Door Operation:

1. Ensure number pad back lighting is off. 2. Enter PIN. 3. Press the UP/DOWN key. 4. Press number key corresponding with desired door (1, 2, or 3). 5. Desired opener will operate. NOTE: Keypad will remain active for 15 seconds after a successful entry is made. During this 15 seconds ANY key will operate the opener. IMPORTANT FEATURES OF THIS KEYPAD:

An audible beep will sound with every key pressed. Keypad will operate, up to, 3 doors with one PIN number. A temporary PIN can be set for convenient non user access. If at any time a mistake is made while programming or operating this keypad, Press the 7 & 9 keys together 3 times. The back light will go out indicating that the keypad is immediately ready for a new entry. 2. Drill a 3/32 pilot hole for the top mounting screw. 3. 4. Hook the slotted mount on back of keypad over the screw. Install included screw into pilot hole, leaving 1/8 gap between the screw head and wall. STEP 5) MOUNTING THE KEYPAD AND REPLACING BATTERIES Keypad MUST be mounted within sight of the garage door(s) at least 5 feet above floor and clear of any moving door parts. Programming will not be lost during battery removal. 1. Remove battery cover and batteries. Replace if necessary. NOTE: Only use standard or alkaline AAA batteries. DO NOT use rechargeable batteries Screw head gap 1/8"

Wall

- ACCESS TO THE GARAGE DOOR OPENER IS REQUIRED TO RESET THE KEYPAD TO THE OPENER -

NOTICE CLEARING THE KEYPAD:

If, for any reason, the keypad needs to be reset to factory default, follow these steps:

1. Press and Hold the PRGM & UP/DOWN keys for 5 seconds. 2. The LED will blink twice and go out indicating the keypad is back to factory default. 3. The keypad is now ready to be programmed. 5. Mark and drill a 3/32 pilot hole for the bottom screw and secure keypad to the wall.

(Do not over-tighten). 6. Reinstall batteries. instruction) 6. Enter PIN. 7. Press UP/DOWN key 3 times. Opener #3 will operate. SECTION B - PROGRAMMING THE KEYPAD FOR DIP SWITCH TYPE OPENERS:

Program Door #1:

1. Enter the OPENER ID written in BOX A -DOOR #1. 2. Press the UP/DOWN key. (LED will go out) 3. Enter switch string written in BOX B for DOOR #1. 4. Press UP/DOWN key. (LED will blink rapidly) 5. Enter PIN. 6. Press UP/DOWN key. Opener #1 will operate. Program Door #2:

1. Press PGRM button twice. 1. Enter the OPENER ID written in BOX A -DOOR #2. 2. Press the UP/DOWN key. (LED will go out) 3. Enter switch string written in BOX B for DOOR #2. 4. Press UP/DOWN key. (LED will blink rapidly) 5. Enter PIN. 6. Press UP/DOWN key. Opener #2 will operate. Program Door #3:

1. Press PGRM 3 times. 1. Enter the OPENER ID written in BOX A -DOOR #3. 2. Press the UP/DOWN key. (LED will go out) 3. Enter switch string written in BOX B for DOOR #3. 4. Press UP/DOWN key. (LED will blink rapidly) 5. Enter PIN. 6. Press UP/DOWN key. Opener #3 will operate. SETTING A TEMPORARY PIN:

If the keypad is to be used by, normally, unauthorized personnel (Such as a repairman) a temporary PIN can be assigned to that personnel to gain access to the garage. This PIN will remain active until the main set entry code is used. 1. Enter current active PIN. 2. Press PRGM key three times. (LED will turn solid indicating keypad is ready for temporary PIN) 3. Enter temporary PIN. (3-8 digits). 4. Press PGRM key one time (LED will blink twice and go out indicating a temporary PIN is set) 5. To cancel the temporary PIN. Operate the keypad/door with the original main PIN. 6. Follow the instructions below pertaining to the garage door opener to be programmed to use new PIN. RESETTING PIN:

Once the original main PIN is changed, the keypad must be reset to the garage door opener per instructions. 1. Enter current active PIN. 2. Press PRGM key one time. (LED will turn solid indicating keypad is ready for new PIN) 3. Enter new PIN. (3-8 digits). 4. Press PGRM key one time (LED will blink twice and go out indicating a new PIN is set) 5. Follow the instructions below pertaining to the garage door opener to be programmed to use new PIN. For questions, comments or troubleshooting, contact The Genie Company at:

1 Door Drive, Mount Hope Ohio, 44660 or call 1-800-354-3643 or visit our website at: www.geniecompany.com FCC Part 15.21 Statement:

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC / IC Statement:

This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. FRENCH & SPANISH VERSIONS GO HERE

8 7 6 5 4 3 2 1 NOTES: (UNLESS OTHERWISE SPECIFIED) 1. BLACK GRAPHICS AND TYPE ON 2 MIL MYLAR WITH PRESSURE SENSITIVE PERMANENT ADHESIVE FOR USE ON ABS PLASTIC, 1 MIL CLEAR MYLAR OVERLAY. D 2 COLOR PER ANSI Z535.1. ER/GCO REV 504392 00135

A REVISIONS DESCRIPTION ORIGINAL ISSUE DATE APPROVAL CHANGED FCC ID FROM "B8Q UKEP" TO

"B8Q-UKEP"

1/30/20 MLS 25.40 2 ORANGE BACKGROUND WHITE BACKGROUND P/N 41214B 4X R0.76 P/N 41214A D C B A PLOTTED: 1/30/20 UNLESS OTHERWISE SPECIFIED APPROVALS PER ASME Y14.5M INTERPRET DIMS & TOLS ALL DIMS ARE IN THE DRAWINGS AND ALL OTHER INFORMATION CONTAINED HEREIN ARE THE CONFIDENTIAL PROPRIETARY PROPERTY OF OVERHEAD DOOR CORPORATION, INCLUDING ITS AFFILIATED SUBSIDIARIES AND AFFILIATES. THIS DRAWING INFORMATION, IN WHOLE OR IN PART, MAY NOT BE COPIED IN ANY MANNER OR DISCLOSED TO ANYONE WITHOUT PRIOR WRITTEN CONSENT OF OVERHEAD DOOR CORPORATION. DISCLOSURE OF ANY DRAWING OR INFORMATION IS INTENDED NOT TO AND SHALL NOT OPERATE AS A LICENSE OR AUTHORIZATION TO USE IT QUALITY DESIGN FEATURES

& MUST MEET APPLICABLE FOR ANY PURPOSE WITHOUT SPECIFIC IN-PROCESS INSPECTION WRITTEN CONSENT OF OVERHEAD DOOR STANDARDS. CORPORATION. DIMS AND SPECIFICATIONS CIRCLED WITH SYMBOL

' ARE CRITICAL TO DO NOT SCALE MM TOLERANCES:

.X = .1

.XX = .01

.XXX = .005 ANGULAR = 1 DRAWN CHECKED APPROVED MATERIAL RSM DRU J.W. SEE NOTES DATE 10/03/19 1/3/20 1/9/20 HOLES:

< .251 =

.251-.500 =

> .500 =

ALL GEOMETRY GOVERNED BY 3D CAD DATABASE:

.003

.003

.003 FINISH 41214 CLEAN

3 7 6 5 4 A SUBSIDIARY OF OVERHEAD DOOR CORPORATION MT. HOPE, OHIO DESCRIPTION LABEL, FCC/IC, UNIVERSAL KEYLESS ENTRY PAD (UKEP) SIZE DWG NO. B 41214 SCALE 8:1 2 SHEET 1 OF 1 1 3.76 9.53 WHITE BACKGROUND C B A THIRD ANGLE PROJECTION ENG F.20.041B-(FORM REV A) 8

Genie Company P. O. Box 67 Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com January 27, 2023 Nemko North America Inc. Attn: Director of Certification 303 River Road Ottawa, Ontario, Canada K1V 1H2 Authority to Act as Agent FCC On our behalf, | appoint Chip Fleury, of Nemko USA Inc. at 2210 Faraday Avenue, Suite 150, Carlsbad, California 92008 to act as our agent in the preparation of this application for equipment certification.

| certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko North America Inc., still resides Radius Networks, Inc., 1228 31st St. SW, Suite 2, Washington D.C. 20007. Dated this Jol Day of Jan u ary , 20. ZB Title:

Genie Company P. O. Box 67 Mt. Hope, OH 44660 iy Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com January 27, 2023 Authority to Act as Agent FCC On our behalf, | appoint David Hui, of Genie Company. at P.O. Box 67, Mt. Hope, Ohio, 44660 to act as our agent in the preparation of this application for equipment certification.

| certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in FCC regulations will have affixed to it a label identical to that submitted for approval with this application. In signing this letter, Applicant certifies that neither the applicant nor any party to the application is not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. For instances where our authorized agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko North America Inc., still resides Radius Networks, Inc., 1228 34st St. SW, Suite 2, Washington D.C. 20007. Dated this PA; Day op Sawaney , 20 23 Signed:

Print Name:

Title: [-27 -LOAZ

The Genie Company P. O. Box 67 Mt. Hope, OH 44660 :

Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com February 3, 2023 *

Nemko North America Inc. Attn: Director of Certification 303 River Road Ottawa, Ontario, Canada K1V 1H2 Authorization of The Genie Company associates to Act on behalf of The Genie Company for all

: applications to FCC and ISED *

Pursuant to 47 CFR 2.911, The Genie Company has authorized the following The Genie Company associates to act on our behalf with respect to Federal Communications Commission (FCC) and Industry of Canada (ISED) applications and Filings. List of Names:

David Hui As such the listed associated are authorized to 1) sign Form 731, 2) sign letters of application, 3) request confidentiality, and exchange data and information with the FCC and/or authorized TCBs on behalf of The Genie Company. In addition, these individuals shall be considered authorized individuals to act on Genies behalf where an authorized individuals attestation is necessary or preferred. This authorization remains in effect until notified to the contrary by The Genie Company. Dated this 6 Day of rebeuacy 20 2%

Signed:

Print Name:_// ike i tle Title: NIVA F ;

Genie Company P. O. Box 67 Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com To whom it may concern, Software was developed to add the 360MHz, 380MHz and 412MHz to model GUK and OUK. No software modifications were developed that affected previously certified frequencies or protocols. No hardware modifications were developed. Applicant Company name: GMI Holdings, Inc. d/b/a The Genie Company Contact Name: David Hui Address: 1 Door Drive Telephone No: 214 579 6325 Fax No: N/A Email: David _Hui@geniecompany.com FCC ID: BBQ-UKEP ISED Certification / Registration Number: ISED: 2133A-UKEP Signature: pf Date: 2/27/2023 Signed by (printed name): David Hui

Genie Company P. O. Box 67 Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com January 27, 2023 Nemko Canada Inc. 303 River Road Ottawa, ON Canada K1V 1H2 REQUEST FOR CONFIDENTIALITY Name of Applicant: GMI Holdings, Inc. d/b/a The Genie Company Address: One Door Drive, PO Box 67 City: Mount Hope Country: USA FCC ID: BBQ-UKEP IC ID: 2133A-UKEP Pursuant to Sections 0.457(d) and 0.459 of the commissions rules and Industry of Canada Regulations stated in RSP-100 Clause 12, we hereby request that the following documents be held under confidentiality. LONG TERM:

1. SCHEMATIC 2. BILL OF MATERIAL 3. THEORY OF OPERATION SHORT TERM (For Canada there is no option for short term confidentiality See RSP-100 Clause 12.4) 1. NA The above information contains trade secrets and proprietary information not customarily released to the public. The public disclosure of this information might be harmful to the applicant and provide unjustified benefits to its competitors. pated: Javuaey 27 Zo23 Signed:

Title: /\ At ENAA Eas NECK Printed: ANI 2) | j

Genie Company P. O. Box 67 ta Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com Covered Equipment Certification Attestation Letter 3/13/2023 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATTN.: Reviewing Engineer FCC ID: BBQ-UKEP GMI Holdings, Inc. d/b/a The Genie Company (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not covered equipment. GMI Holdings, Inc. d/b/a The Genie Company (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Signed: nl eee Printed name: David Hui Title: RF Engineer Company Name: GMI Holdings, Inc. d/b/a The Genie Company Date: 3/13/2023

Genie Company P. O. Box 67 Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR)

} Fax: 330-763-8042 www.geniecompany.com U.S. Agent Designation for Service of Process -

Certification Attestation Letter March 15, 2023 Nemko North America, Inc. 303 River Road Ottawa K1V 1H2 Canada ATIN.: Reviewing Engineer FCC ID: BBQ-UKEP Per section 2.911(d)(7) of the FCC rules, The Genie Company a Division of Overhead Door Corporation (the applicant) certifies that the equipment for which authorization is sought is designated to the following U.S. Designated agent* for service of process:

Company Name: The Genie Company a Division of Overhead Door Corporation ;

Physical U.S. Company Address: 1 Door Drive, Mt. Hope, Texas, 44660, USA Agent name: Mike Whitley Agent Email Address: mike_whitley@geniecompany.com FRN: 0004055760 The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: /

Signed: s MN Printed name: ~ David Hui Title: Antenna Engineer Company Name: The Genie Company a Division of Overhead Door Corporation Date: March 15, 2023 the applicant must designate a contact located in the United States for purposes of acting as the applicant's agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process.

Genie Company P. O. Box 67 Mt. Hope, OH 44660 Phone: 800-827-3667 (DOOR) Fax: 330-763-8042 www.geniecompany.com Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, Illinois 60515-1082 FCC ID: B8Q UKEP Product Name: Universal Keypad Model: GUK-BX, GUK-R, OUK-BX Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

Electrical Schematics, Layout Drawings, and Bills of Materials Theory of Operation Documentation / Technical Description PCB Assembly and Block Diagram These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 15th Day of October 2019 By:

Title: Sr. RF Engineer On behalf of :

The Genie Company a Division of Overhead Door Corporation Telephone:

Mike Whitey Printed 830-660-0800 Signature