Q-TRACK Q-DOSE SIMULATED DOSIMETER QUICK START GUIDE Q-TRACK QT-640 TAG TRANSMITTER QUICK START GUIDE NOTE: CHARGE BEFORE FIRST USE! FOUR HOURS IN THE QT-654 CRADLE CHARGER NOTE: CHARGE BEFORE FIRST USE! FOUR HOURS IN THE QT-654 CRADLE CHARGER WILL YIELD A FULL CHARGE SHOULD YIELD SOLID GREEN CHARGED LED The Q-Dose Simulated Dosimeter emulates the functionality of the Mirion DMC 2000:
Display: The display shows simulated dose and rate data and other user information. Interfaces: Include two charging contacts and a mini-USB interface. Button: The button toggles the Q-Dose through three modes of operation:
Display 1. Sleep Mode: The Q-Dose goes to sleep to conserve battery life when left in Pause mode for a prolonged period. To wake up the tag, hold the button 3 seconds or until the display illuminates, indicating the Q-Dose is in Pause mode. 2. Pause Mode: This mode allows the user to configure or view administrative settings. Each subsequent button press cycles through the following functions:
Change: At the change menu, wait five seconds and the text Enter will appear. Then push the button again to enter Run Mode. Frequency: Displays the frequency of the tag to which the Q Dose is assigned. A Q-Dose may be assigned to a different tag through the Q-Track software. Mini-
USB MAC Address: Displays the MAC address of the device. This uniquely identifies the Q-Dose in the selection dialog in the Q-Track software. Battery Voltage: Displays the battery voltage: 4.1V is a full charge;
3.6V denotes a low battery. Button Charging Contacts Firmware Version: Displays the version number of the Q-Dose firmware. DoseAlarm: Displays the Dose Alarm set point defined in the Q-Track software. RateAlarm: Displays the Rate Alarm set point defined in the Q-Track software. Dose: Displays Dose Pre-Alarm set point defined in the Q-Track software. Rate: Displays Rate Pre-Alarm set point defined in the Q-Track software. TimeAlarm: Displays Time set point defined in the Q-Track software (under development). Pause: Back to the beginning of the Pause options. 3. Run Mode: From Pause Mode, push the button until Change appears. Wait five seconds until Enter appears, then push the button again to enter Run Mode. While in Run Mode, the button press will toggle between Dose and Rate. To exit Run Mode, push and hold the button ten seconds. The display will read Go Out. Push the button once more to enter Pause Mode. The Q-Dose Simulated Dosimeter is a ZigBee-transceiver-equipped simulated dosimitter emulating a Mirion DMC 2000. Q-Dose antennas are self-contained within the plastic enclosure, and cannot be modified or changed by the user. Q-Track Corp. FCC ID: VJ3-Q-DOSE. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) the device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Q-Track Corporation; Model: Q-Dose; IC: 10503A-QDOSE. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This product meets the applicable Industry Canada technical specifications. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. Cet appareil est conforme Industrie Canada une licence standard RSS exonrs (s). Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne doit pas provoquer d'interfrences 2. Cet appareil doit accepter toute interfrence reue, y compris les interfrences pouvant provoquer un fonctionnement indsirable de l'appareil. Ce produit est conforme aux spcifications d'Industrie Canada. Cet appareil est conforme aux limites dexposition aux rayonnements dfinies pour un environment non cntrol. The Q-Track Corporation 2223 Drake Avenue SW 1st Floor Huntsville, AL 35805 www.q-track.com