HR True Wireless Earbuds 8083575 EN Product Description and Accessories Touch button Indicator light / microphone Charging case Earmus x 3 pairs USB charging cable There are dierent size of earmus attached in the package, please select the suitable ones to wear. Operational Guide Charge the Headphones During using, if only red light ashes, it indicates headphones are at low battery level, please use them after fully charged. Charging: place the headphones into the charging case Red light lit in a breathing pattern = charging Red light o = fully charged Charging time: about 1.5 hours for a full charging Charge the Charging Case If indicator light ashes slowly, its ashing times mean the times that the headphones can be charged, if the indicator light ashes rapidly, it means the charging case has a low battery capacity, please charge it in time; once the battery runs out, the headphones cannot be turned on. Indicator light steady lit = charging Indicator light o = fully charged Rated input: 5V 60mA(headphone) 5V 500mA(charging case) Warning: The rechargeable batteries that provide power for this product must be disposed properly for recycling. Do not dispose of batteries in
re to prevent an explosion. If not used for long periods of time, it is recommended to charge the product with lithium battery at least once per 3 months. Power ON/OFF 1. Power on automatically when taken out from the charging case;
2. Power o automatically while placed into the charging case. Bluetooth Connection 1. Two Headphones Mode Open the charging case to take two headphones out, press and hold the touch button of the left headphone to enter pairing state, red and blue light ashing rapidly;
Set mobile phone to search for and connect to EDIFIER TWS1, after pairing is successful, blue light will ash slowly. 2. One Headphone Mode If use one headphone only, please take the left or right headphone out from the charging case, and refer to the procedures mentioned in Two Headphones Mode to pair it with mobile phone. TWS (true wireless stereo) Pairing of the Left and Right Headphones The left and right headphones have nished TWS pairing before leaving the factory. If the wireless connection fails to resume, please follow the steps below to re-pair:
With no TWS and Bluetooth connection, double press the touch buttons to enter TWS pairing state, blue lights ashing rapidly;
After pairing is done, blue lights of two headphones will ash slowly. Functional Operation Instructions Music playback (same operation for the left and right headphones) Skip backward: triple tap Skip forward: double tap Pause: single tap Play: single tap Call (same operation for the left and right headphones) Accept a call: single tap End a call: single tap Decline a call: press and hold Clear pairing records: With no TWS and Bluetooth connection, respectively press and hold the touch button for 8 seconds. Disconnect from mobile phone: When the phone is connected, no music is playing and no phone conversation, press and hold the touch button for 5 seconds. FAQs Red light instead of blue light ashes. The headphones are at low battery level, please recharge the headphones. Red light is o during charging. Please ensure the headphones are correctly placed into the charging case. When the headphones are not used for long periods of time, the battery will enter sleep state, it needs to charge about 30 minutes and then the red light will be lit. No sound Check if the headphones are operating. Check if the headphones volume is at an appropriate level. Check if the headphones are correctly connected with mobile phone. Check if the headphones are operating within a normal working range. The call quality of the headphones is not good. Check if mobile phone is in an area with strong signal. Please ensure the headphones are within eective distance (10m) and no obstacle between the headphones and mobile phone. When playing music, cannot control pause/play/previous track/
next track via headphones. Please ensure the paired device support AVRCP (Audio/Video Remote Control Prole) prole. Maintenance During using, please read the following suggestions carefully. Keep the product away from humid places to avoid aecting internal circuit. Do not use the product during intense exercise or with much sweat to prevent sweat from dropping into the product to make damage. Do not put the product in places exposed to sun or with high temperature. High temperature will shorten service life of electronic components, damage battery and deform plastic components. Do not put the product in cold places to avoid damaging internal circuit board. Do not dismantle the product. Non-professional personnel may damage the product. Do not drop, strongly vibrate, strike the product with hard object to avoid damaging internal circuit. Do not use drastic chemicals or cleaner to clean the product. Do not use sharp objects to scratch product surface to avoid damaging shell and aecting looking. If the product cannot operate properly, please send it to your qualied maintenance agency. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. Caution: changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. ISED Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
Lappareil ne doit pas produire de brouillage;
Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.